Prime-Line N 6545 Operating instructions

Brand
Prime-Line
Model
N 6545
Type
Operating instructions

Prime-Line N 6545:

This product is a bi-fold door top pivot, designed to replace the top pivot of a bi-fold door. It allows for vertical and horizontal adjustment, and has a snap-in snugger (spring stop) to keep the door in place. The N 6545 is easy to install and can be used to replace a broken or damaged top pivot, or to adjust the height and alignment of a bi-fold door.

Features:

  • Vertical and horizontal adjustment
  • Snap-in snugger (spring stop)
  • Easy to install

Possible use cases:

  • Replacing a broken or damaged bi-fold door top pivot
  • Adjusting the height and alignment of a bi-fold door

Prime-Line N 6545:

This product is a bi-fold door top pivot, designed to replace the top pivot of a bi-fold door. It allows for vertical and horizontal adjustment, and has a snap-in snugger (spring stop) to keep the door in place. The N 6545 is easy to install and can be used to replace a broken or damaged top pivot, or to adjust the height and alignment of a bi-fold door.

Features:

  • Vertical and horizontal adjustment
  • Snap-in snugger (spring stop)
  • Easy to install

Possible use cases:

  • Replacing a broken or damaged bi-fold door top pivot
  • Adjusting the height and alignment of a bi-fold door
N 6545-INS
TOOLS NEEDED
HERRAMIENTAS REQUERIDAS
OUTILS REQUIS
NOTE: Installation drawings are typical for this style of replacement part. They may not show a part identical to the
one you are installing.
NOTA: Los dibujos para la instalación son genéricos para repuestos de este tipo; por lo que podrían no mostrar una
pieza idéntica a la que usted esté instalando.
REMARQUE : Les dessins d'installation sont typiques pour ce style de pièce de rechange. Ils pourraient ne pas
illustrer une pièce identique à celle que vous installez.
N-6545
Phillips Screwdriver
Destornillador Phillips
Tournevis Phillips
Screwdriver
Destornillador
Tournevis
Bi-fold door top pivot
Puertas de dos dobladuras: Punto de eje superior
Guide supérieur de porte pliante à deux battants
Spring pin in
jamb corner
Clavija de resorte en
la esquina de la jamba
Cheville à ressort du coin
de montant
Spring roller
Rueda de resorte
Roulette à ressort
For vertical adjustment: lift and rotate adjusting wheel. Doors
should just clear header.
Para regular verticalmente, levante y gire la rueda reguladora. La
hojas de la puerta deben quedar apenas distanciadas del
travesaño superior.
Pour le réglage vertical: Levez et tourner la roulette de réglage.
Les portes devraient tout juste dégager la solive de porte.
For horizontal adjustment: lift and slide into next slot. Adjust so
doors have 1/8" gap between pairs of doors at center, or jamb in
a 2 door opening.
Para regular horizontalmente, levante y deslice dentro de la
siguiente ranura. Regule las dos hojas para que queden con una
separación de 1/8" en el centro, o de la jamba en puertas de
doble abertura.
Pour le réglage horizontal: Levez et glissez dans la fente
suivante. Réglez de manière à obtenir un espacement de 1/8" au
centre entre les paires de portes, ou au montant dans les
ouvertures à deux portes.
1. Remove door by lifting up and
tilting bottom out.
2. Replace hardware
3. Vertical adjustment
4. Horizontal adjustment
5. Snap-in snugger (spring stop)
1. Saque la hoja de la puerta
levantándola e inclinándola hacia fuera.
2. Reemplace los elementos de ferretería
3. Regulación vertical
4. Regulación horizontal
5. Enganche el tensionador (tope de resorte)
1. Enlevez la porte en la levant et en inclinant le bas vers
l'extérieur.
2. Remplacez la ferronnerie
3. Réglage vertical
4. Réglage horizontal
5. Tendeur à enclenchement (arrêt à ressort).
33//88"" OO..DD..
10 mm
11//44"" OO..DD..
6 mm
55//1166"" OO..DD..
8 mm
77//1166"" OO..DD..
11 mm
11//22""
13 mm
11--11//22""
38 mm
26950 San Bernardino Ave., Redlands, CA 92374
© 2010 Prime-Line Products
  • Page 1 1

Prime-Line N 6545 Operating instructions

Brand
Prime-Line
Model
N 6545
Type
Operating instructions

Prime-Line N 6545:

This product is a bi-fold door top pivot, designed to replace the top pivot of a bi-fold door. It allows for vertical and horizontal adjustment, and has a snap-in snugger (spring stop) to keep the door in place. The N 6545 is easy to install and can be used to replace a broken or damaged top pivot, or to adjust the height and alignment of a bi-fold door.

Features:

  • Vertical and horizontal adjustment
  • Snap-in snugger (spring stop)
  • Easy to install

Possible use cases:

  • Replacing a broken or damaged bi-fold door top pivot
  • Adjusting the height and alignment of a bi-fold door
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents