quickstart guide
EDU-500
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
EDU-500
QUICKSTART DOC. 8271A (2050999) 03.18
Student Collaboration Workstation
Verify Contents
Check the table below for the system's package contents before starting installation. The following items are
included:
Additional Requirements
The following items are also required to build a student collaboration workstation.
• A video display (not included) must be connected to the HD-WP-4K-401-C.
• Source devices (not included) may be connected to the TT-100-devices.
The Crestron
®
EDU-500 Student Collaboration Workstation provides all the hardware required to build a collaboration
solution for an educational setting.
Preparation
1
1
Display
HDMI
TT-100
TT-100
TT-100
TT-100
HD-WP-4K-401-C
USB
HDMI
USB
HDMI
USB
HDMI
USB
HDMI
CAT5e
LAN
QUANTITY ITEM PART NUMBER
1 CBL-CAT5E-7, Ethernet LAN Cable, 7 feet (2.13 m)
6509924
4 CBL-HD-6, HDMI Interface Cable, 6 feet (1.83 m)
6503565
1 CBL-HD-20, HDMI Interface Cable, 20 feet (6.10 m)
6503567
1 HD-WP-4K-401-C, 4K Multi-Window Video Processor with
HDBaseT
®
& HDMI
®
Outputs
6507977
4 TT-100-B-T, Crestron Connect It™ Cable Caddy w/120V Outlet,
No Cables, Black Textured
6506815
quickstart guide
EDU-500
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
QUICKSTART DOC. 8271A (2050999) 03.18
Student Collaboration Workstation
EDU-500
LAN
2
Connect the System
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, and Crestron Connect It are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries.
HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other
countries. HDMI is either a trademark or a registered trademark of HDMI Licensing LLC in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
HD-WP-4K-401-C
2
When all connections are made, apply power to all of the devices in the system. Then, use the HD-WP-4K-401-C out-of-the-box functionality to present audio/video sources connected to the TT-100 devices on the video display device.
If more than one source is connected, two or more equally-sized windows appear on the display. Press the button on the TT-100 while the LED is blue to display the associated source as a full-screen window on the display. Press the button
again while the LED is green to allow the display to return to the previous configuration (two, three, or four windows). For more information, refer to the HD-WP-4K-401-C DO Guide (Doc. 7900) at www.crestron.com/manuals.
Apply Power and Present Sources
3
For more information, refer to the HD-WP-4K-401-C DO Guide (Doc. 7900), the HD-WP-4K-401-C Supplemental Guide (Doc. 7901), and the TT-100 Series DO Guide (Doc. 7833) at www.crestron.com/manuals.
More Information
4
100-240V ~ 2.0A
50/60Hz
Make the following connections to the HD-WP-4K-401-C:
Connect each of the four CBL-HD-6 cables to one of the HDMI INPUT ports, and then route each cable through one of the TT-100 devices as described in the TT-100 Series DO Guide (Doc. 7833) at
www.crestron.com/manuals.
Connect each of the four USB 2.0, A to Micro B cables (included with each TT-100 device) to one of the USB INPUT ports and to the micro USB port on the appropriate TT-100 device. Ensure that each TT-100 device is
connected to a matching HDMI and USB input pair on the HD-WP-4K-401-C.
Connect a video display device (not included) to the HDMI OUTPUT port with the CBL-HD-20 cable.
Connect the LAN to the (LAN) port using the CBL-CAT5E-7 cable.
Connect power cord included with the HD-WP-4K-401-C to an ac power outlet.
/
