OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 07/19)
MODEL W1859/W1860
8" X 76" PARALLELOGRAM
JOINTER W/MOBILE BASE
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © NOVEMBER, 2018 BY WOODSTOCK INTERNATIONAL, INC. REVISED AUGUST, 2019 (AI)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#19884ES Printed in Taiwan
175370
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
SETUPELECTRICAL MAINTENANCE
SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION .....................................2
Machine Differences ............................. 2
Woodstock Technical Support .................. 2
Machine Specifications (W1859) ............... 3
Machine Specifications (W1860) ............... 5
Identification ..................................... 7
Controls & Components ......................... 8
SAFETY ............................................. 10
Standard Machinery Safety Instructions .... 10
Additional Safety for Jointers ................ 12
ELECTRICAL ....................................... 13
Circuit Requirements .......................... 13
Grounding Requirements ...................... 14
Extension Cords ................................ 14
SETUP .............................................. 15
Unpacking ....................................... 15
Items Needed for Setup ....................... 15
Inventory ........................................ 16
Cleaning Machine ............................... 17
Machine Placement ............................ 18
Assembly ......................................... 19
Knife-Setting Jig (W1859) ..................... 21
Dust Collection ................................. 22
Test Run .......................................... 23
Tensioning Belt ................................. 23
Disabling & Locking Switch ................... 24
OPERATIONS....................................... 25
General .......................................... 25
Stock Inspection ................................ 26
Squaring Stock .................................. 27
Surface Planing ................................. 28
Edge Jointing ................................... 29
Bevel Cutting ................................... 30
Rabbet Cutting ................................. 31
Setting Depth of Cut ........................... 33
ACCESSORIES ...................................... 35
Jointer Accessories ............................. 35
MAINTENANCE .................................... 37
General .......................................... 37
Cleaning & Protecting ......................... 37
Lubrication ...................................... 38
SERVICE ............................................ 39
General .......................................... 39
Setting/Replacing Knives (W1859) ........... 39
Rotating/Replacing Helical Cutterhead
Inserts (W1860) ................................. 43
Checking/Adjusting Table Parallelism ...... 45
Setting Outfeed Table Height ................ 49
Calibrating
1
⁄8" Infeed Table Stop ........... 50
Setting Fence Stops ............................ 51
Calibrating Depth-of-Cut Scale .............. 54
Tensioning/Replacing Belt .................... 55
Checking/Aligning Pulleys .................... 56
Checking/Adjusting Cutterhead Guard ..... 57
Troubleshooting ................................. 58
Electrical Safety Instructions ................. 60
Wiring Diagram ................................. 61
PARTS .............................................. 62
Tables, Fence & Cutterhead .................. 62
Base, Stand & Motor ........................... 63
Labels & Cosmetics ............................ 66
WARRANTY ........................................ 69
Contents
-2-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
INTRODUCTION
Woodstock Technical Support
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
Models W1859 and W1860 are 3 HP, 8" x 76" jointers with the following differences:
• Model W1859 has a 4-knife cutterhead with high-speed steel knives.
• Model W1860 has a helical cutterhead with 4 helicals and 36 indexable carbide inserts.
Machine Differences
-3-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
Model W1859 Machine Specifications, Page 1 of 3
MODEL W1859
8" X 76" PARALLELOGRAM JOINTER WITH MOBILE BASE
Product Dimensions
Weight.......................................................................................................... 365 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height................................... 76 x 25 x 41‐1/2 in.
Footprint (Length x Width).............................................................................. 40 x 16 in.
Shipping Dimensions
Type....................................................................................................... Wood Crate
Content........................................................................................................ Machine
Weight.......................................................................................................... 470 lbs.
Length x Width x Height........................................................................... 85 x 26 x 43 in.
Must Ship Upright.................................................................................................. Yes
Electrical
Power Requirement.................................................................... 230V, Single‐Phase, 60 Hz
Motor Size......................................................................................................... 3 HP
Full‐Load Current Rating......................................................................................... 12A
Minimum Circuit Size............................................................................................. 20A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 6 ft.
Power Cord Gauge............................................................................................ 14 AWG
Plug Included....................................................................................................... Yes
Included Plug Type............................................................................................... 6‐20
Switch Type................................................... Push Button Magnetic w/Large Shut‐Off Paddle
Motors
Main
Horsepower................................................................................................. 3 HP
Phase.............................................................................................. Single‐Phase
Amps.......................................................................................................... 12A
Speed.................................................................................................. 3450 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ..................................................................................... Belt Drive
Bearings................................................................. Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type................................................................. External
Machine Specifications (W1859)
-4-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
Model W1859 Machine Specifications, Page 2 of 3
Main Specifications
Main Specifications
Jointer Size................................................................................................. 8 in.
Bevel Jointing................................................................................. 0 – 45 deg. L/R
Maximum Width of Cut................................................................................... 8 in.
Maximum Depth of Cut................................................................................ 1/8 in.
Minimum Workpiece Length............................................................................ 10 in.
Minimum Workpiece Thickness....................................................................... 1/2 in.
Maximum Rabbeting Depth............................................................................ 1/2 in.
Number of Cuts Per Minute............................................................................ 22,000
Fence Information
Fence Length............................................................................................. 38 in.
Fence Width........................................................................................... 1‐1/4 in.
Fence Height.......................................................................................... 4‐1/2 in.
Fence Stops.................................................................................. 45, 90, 135 deg.
Cutterhead Information
Cutterhead Type........................................................................................ 4 Knife
Cutterhead Diameter............................................................................... 3‐1/16 in.
Cutterhead Speed................................................................................... 5500 RPM
Knife Information
Number of Knives.............................................................................................. 4
Knife Type................................................................................... HSS, Single‐Sided
Knife Length................................................................................................ 8 in.
Knife Width.............................................................................................. 3/4 in.
Knife Thickness......................................................................................... 1/8 in.
Knife Adjustment.................................................................... Jack Screws or Springs
Table Information
Table Length.............................................................................................. 76 in.
Table Width................................................................................................ 8 in.
Table Thickness....................................................................................... 1‐3/4 in.
Floor to Table Height.............................................................................. 31‐1/4 in.
Table Adjustment Type......................................................................... Lever Action
Table Movement Type......................................................................... Parallelogram
Construction
Body Assembly........................................................................................ Cast Iron
Cabinet............................................................................................. Sheet Metal
Fence Assembly................................................................. Precision‐Ground Cast Iron
Guard...................................................................................... Die‐Cast Aluminum
Table............................................................................. Precision‐Ground Cast Iron
Paint Type/Finish............................................................................. Powder Coated
Other Information
Number of Dust Ports......................................................................................... 1
Dust Port Size.............................................................................................. 4 in.
Mobile Base............................................................................................. Built‐In
-5-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
Model W1860 Machine Specifications, Page 1 of 3
MODEL W1860
8" X 76" PARALLELOGRAM JOINTER WITH HELICAL CUTTERHEAD &
MOBILE BASE
Product Dimensions
Weight.......................................................................................................... 365 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height................................... 76 x 25 x 41‐1/2 in.
Footprint (Length x Width).............................................................................. 40 x 16 in.
Shipping Dimensions
Type....................................................................................................... Wood Crate
Content........................................................................................................ Machine
Weight.......................................................................................................... 470 lbs.
Length x Width x Height........................................................................... 85 x 26 x 43 in.
Must Ship Upright.................................................................................................. Yes
Electrical
Power Requirement.................................................................... 230V, Single‐Phase, 60 Hz
Motor Size......................................................................................................... 3 HP
Full‐Load Current Rating......................................................................................... 12A
Minimum Circuit Size............................................................................................. 20A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 6 ft.
Power Cord Gauge............................................................................................ 14 AWG
Plug Included....................................................................................................... Yes
Included Plug Type............................................................................................... 6‐20
Switch Type................................................... Push Button Magnetic w/Large Shut‐Off Paddle
Motors
Main
Horsepower................................................................................................. 3 HP
Phase.............................................................................................. Single‐Phase
Amps.......................................................................................................... 12A
Speed.................................................................................................. 3450 RPM
Type......................................................................... TEFC Capacitor‐Start Induction
Power Transfer ..................................................................................... Belt Drive
Bearings................................................................. Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type................................................................. External
Machine Specifications (W1860)
-6-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
Model W1860 Machine Specifications, Page 2 of 3
Main Specifications
Main Specifications
Jointer Size................................................................................................. 8 in.
Bevel Jointing................................................................................. 0 – 45 deg. L/R
Maximum Width of Cut................................................................................... 8 in.
Maximum Depth of Cut................................................................................ 1/8 in.
Minimum Workpiece Length............................................................................ 10 in.
Minimum Workpiece Thickness....................................................................... 1/2 in.
Maximum Rabbeting Depth............................................................................ 1/2 in.
Number of Cuts Per Minute............................................................................ 22,000
Fence Information
Fence Length............................................................................................. 38 in.
Fence Width........................................................................................... 1‐1/4 in.
Fence Height.......................................................................................... 4‐1/2 in.
Fence Stops.................................................................................. 45, 90, 135 deg.
Cutterhead Information
Cutterhead Type........................................................................................ Helical
Cutterhead Diameter............................................................................... 3‐1/16 in.
Number of Cutter Spirals..................................................................................... 4
Number of Indexable Cutters............................................................................... 36
Cutterhead Speed................................................................................... 5500 RPM
Cutter Insert Information
Cutter Insert Type........................................................................ Indexable Carbide
Cutter Insert Length.................................................................................... 15 mm
Cutter Insert Width..................................................................................... 15 mm
Cutter Insert Thickness............................................................................... 2.5 mm
Table Information
Table Length.............................................................................................. 76 in.
Table Width................................................................................................ 8 in.
Table Thickness....................................................................................... 1‐3/4 in.
Floor to Table Height.............................................................................. 31‐1/4 in.
Table Adjustment Type......................................................................... Lever Action
Table Movement Type......................................................................... Parallelogram
Construction
Body Assembly........................................................................................ Cast Iron
Cabinet............................................................................................. Sheet Metal
Fence Assembly................................................................. Precision‐Ground Cast Iron
Guard...................................................................................... Die‐Cast Aluminum
Table............................................................................. Precision‐Ground Cast Iron
Paint Type/Finish............................................................................. Powder Coated
Other Information
Number of Dust Ports......................................................................................... 1
Dust Port Size.............................................................................................. 4 in.
Mobile Base............................................................................................. Built‐In
-7-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
Identification
Become familiar with the names and locations of the controls and features shown below to better
understand the instructions in this manual.
For Your Own Safety Read Instruction Manual Before Operating Jointer
a) Wear eye protection.
b) Always keep cutterhead and drive guards in place and in proper operating condition. If
removed, ALWAYS replace cutterhead guard immediately after rabbeting operations.
c) Never make cuts deeper than
1
⁄8" per pass.
d) Always use hold-down or push blocks when jointing material narrower than 3" or planing
material thinner than 3".
e) Never perform jointing, planing, or rabbeting cuts on pieces shorter than 10" in length.
Mobile Base Lock Knobs
Push Block
Holders (2 of 4)
Infeed Table
Adjustment Lever
Infeed
Table
Infeed Table Lock
Depth-of-Cut Scale
ON/STOP SwitchInfeed Table Stop
Release Knob
Fence
Outfeed
Table
Outfeed
Table Lock
Outfeed Table
Adjustment Lever
Cutterhead
Guard
Fence Tilt
Handle
Rear Access
Panel
Fence
Adjustment
Knob
Fence Tilt Lock
Fence Lock
Lever
4" Dust
Port
-8-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
Controls & Components
Refer to the Figures 1–4 and the following descriptions to
become familiar with the basic controls and components
of this machine. Understanding these items and how they
work will help you understand the rest of the manual and
stay safe when operating this machine.
Figure 1. ON/STOP controls.
A
B
Figure 2. Table controls and components,
fence, and mobile base lock knobs.
C
D
H
E
F
G
A. ON Button: Push to start motor. Insert padlock
through button to disable (padlock not included).
B. STOP Paddle: Push to stop motor.
C. Outfeed Table: Supports workpiece after it passes
over cutterhead. For optimum results, outfeed table
must be properly adjusted even with highest point of
cutterhead knives/inserts.
D. Fence: Supports workpiece laterally as it moves
across cutterhead; determines angle of cut when
edge or bevel jointing.
E. Infeed Table: Supports workpiece before it reaches
cutterhead. Position of infeed table relative to
cutterhead knives/inserts determines depth of cut.
F. Infeed Table Adjustment Lever: Move up or down
to adjust position of infeed table (when infeed table
lock is loosened).
G. Mobile Base Lock Knobs: Tighten to secure jointer
in position; loosen to move jointer.
H. Outfeed Table Adjustment Lever: Move up or down
to adjust position of outfeed table (when outfeed
table lock is loosened). Only used when setting
outfeed table even with cutterhead knives/inserts.
To reduce your risk of serious injury
or damage to the machine, read this
entire manual BEFORE using machine.
-9-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
INTRODUCTI ON
I. Cutterhead Guard: Covers cutterhead until
workpiece pushes guard out of the way during
operation. When workpiece leaves cutterhead, guard
springs back to its starting position.
J. Depth-of-Cut Scale: Shows depth of cut (per pass).
K. Infeed Table Lock: Tighten to secure infeed table
position; loosen for table adjustment.
L. Table Release Knob: Pull out to lower infeed
table more than
1
⁄8". Infeed table is factory-set to
automatically stop at
1
⁄8".
M. Outfeed Table Lock: Tighten to secure outfeed
table position; loosen for table adjustment.
N. Fence Tilt Handle: Use to tilt fence throughout its
range of motion from 45° inward to 45° outward
(135°). (Fence tilt lock must be loosened first.)
O. 90° Stop Block: Swivels to engage with 90° stop
bolt. When engaged, stops fence at 90°. When
disengaged, allows bevel cuts greater than 90°.
P. 45° Inward Fence Stop: Stops fence at 45° inward.
Q. 90° Fence Stop: Stops fence at 90°.
R. 45° Outward Fence Stop: Stops fence at 45°
outward (135°).
S. Fence Tilt Lock: Secures fence at any position in
available tilt range.
IMPORTANT: Always tighten tilt lock before starting
machine—even when fence is resting against stops.
T. Fence Lock Lever: Secures fence position.
U. Fence Adjustment Knob: Moves fence position
forward/backward. (Fence lock lever must be
loosened first.)
Figure 3. Table locks, cutterhead guard,
and depth-of-cut scale.
I
M
J
K
L
Figure 4. Fence controls and components.
O
R
T
S
N
P
Q
U
-10-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SAFETY
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
NOTICE
SAFETY
OWNER’S MANUAL.
Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY.
Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DANGEROUS ENVIRONMENTS.
Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
MENTAL ALERTNESS REQUIRED.
Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
Standard Machinery Safety Instructions
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-
sures—this responsibility is ultimately up to the operator!
SAFETY
Standard Machinery Safety Instructions
-11-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SAFETY
WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
HAZARDOUS
DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
HEARING PROTECTION.
Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
REMOVE ADJUSTING TOOLS.
Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
INTENDED USAGE.
Only use machine for its
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leads to serious
personal injury or death!
AWKWARD POSITIONS.
Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
CHILDREN & BYSTANDERS.
Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
GUARDS & COVERS.
Guards and covers reduce
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during
operation greatly increases risk of injury or
loss of control. Before starting, verify machine
is stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
UNATTENDED OPERATION. To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
malfunction, leading to serious personal injury
or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
from heated surfaces, high traffic areas, harsh
chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the
intended operation, stop using the machine!
Contact Technical Support at (360) 734-3482.
-12-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SAFETY
Additional Safety for Jointers
Serious cuts, amputation, entanglement, or death can occur from contact with rotating cutterhead
or other moving components! Flying chips from cutting operations can cause eye injuries or
blindness. Workpieces or inserts/knives thrown by cutterhead (kickback) can strike nearby operator
or bystanders with deadly force. To reduce the risk of serious personal injury from these hazards,
operator and bystanders MUST completely heed the hazards and warnings below.
GRAIN DIRECTION. Jointing against the grain or
end grain can increase the risk of kickback.
It also requires more cutting force, which
produces chatter or excessive chip out.
Always joint or surface plane with the grain.
CUTTING LIMITATIONS. Cutting workpieces
that do not meet minimum dimension
requirements can result in kickback or
accidental contact with cutterhead. Never
perform jointing, planing, or rabbeting cuts
on pieces smaller than specified in data sheet.
PUSH BLOCKS. Push blocks reduce risk of
accidental cutterhead contact with hands.
Always use push blocks when planing
materials less than 3" high or wide. Never
pass your hands directly over cutterhead
without a push block.
WORKPIECE SUPPORT. Poor workpiece support
or loss of workpiece control while feeding
will increase risk of kickback or accidental
contact with cutterhead. Support workpiece
with fence continuously during operation.
Support long stock with auxiliary table if
necessary.
FEED WORKPIECE PROPERLY. Kickback or
accidental cutterhead contact may result if
workpiece is fed into cutterhead the wrong
way. Allow cutterhead to reach full speed
before feeding. Never start jointer with
workpiece touching cutterhead. Always feed
workpiece from infeed side to outfeed side
without stopping until cut is complete. Never
move workpiece backwards while feeding.
SECURE KNIVES/INSERTS. Loose knives or
improperly set inserts can be thrown from
cutterhead with dangerous force. Always
verify knives/inserts are secure and properly
adjusted before operation. Straight knives
should never project more than
1
⁄8" (0.125")
from cutterhead body.
KICKBACK. Occurs when workpiece is ejected
from machine at high rate of speed.
Kickback injuries occur from getting struck
by workpiece or hands being pulled into
cutterhead. To reduce risk of kickback,
only use proper workpieces, safe feeding
techniques, and proper machine setup.
GUARD REMOVAL. Operating jointer without
guards exposes operator to knives/inserts
and other hazardous moving parts. Except
when rabbeting, never operate jointer or
allow it to be connected to power if any
guards are removed. Turn jointer OFF
and disconnect power before clearing
any shavings or sawdust from around
cutterhead. After rabbeting or maintenance
is complete, immediately replace all
guards and ensure they are properly
installed/adjusted before resuming regular
operations.
DULL/DAMAGED KNIVES/INSERTS. Dull or
damaged knives/inserts increase risk of
kickback and cause poor workpiece finish.
Only use sharp, undamaged knives/inserts.
OUTFEED TABLE ALIGNMENT. Setting outfeed
table too high can cause workpiece to hit
table or get stuck while feeding. Setting
outfeed table too low may cause workpiece
to rock or shift while feeding. Both results
will increase risk of kickback. Always keep
outfeed table even with knives/inserts at
highest point during rotation.
INSPECTING STOCK. Impact injuries or kickback
may result from using improper workpieces.
Thoroughly inspect and prepare workpiece
before cutting. Verify workpiece is free of
nails, staples, loose knots or other foreign
material.
MAXIMUM CUTTING DEPTH. To reduce risk of
kickback, never cut deeper than
1
⁄8".
-13-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
ELECTRICAL
ELECTRICAL
Circuit Requirements
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the full-
load current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
Circuit Requirements
This machine is prewired to operate on a power supply
circuit that has a verified ground and meets the following
requirements:
Circuit Type ............ 220V/240V, 60 Hz, Single-Phase
Circuit Size ............................................ 20 Amps
Plug/Receptacle ................................... NEMA 6-20
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
Full-Load Current Rating at 230V ................ 12 Amps
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instrtucted to do so later
in this manual.
Incorrectly wiring or grounding this
machine can cause electrocution, fire,
or machine damage. To reduce this risk,
only an electrician or qualified service
personnel should do any required
electrical work on this machine.
NOTICE
The circuit requirements listed in this
manual apply to a dedicated circuit—
where only one machine will be running
at a time. If this machine will be
connected to a shared circuit where
multiple machines will be running at the
same time, consult with an electrician
to ensure that the circuit is properly
sized for safe operation.
Electrical
-14-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
ELECTRICAL
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of
malfunctions or breakdowns, grounding provides
a path of least resistance for electric current
to travel—in
order
to reduce the risk of electric shock.
Improper connection of the equipment-grounding
wire
will
increase
the risk of electric shock. The wire with green
insulation
(with/without yellow stripes) is the equipment-
grounding
wire. If repair or replacement of the power
cord or plug is necessary, do not connect the equipment-
grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel
if
you do not understand these grounding requirements,
or if
you are in doubt about whether the tool is
properly grounded.
If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
This machine is equipped with a power cord that has
an equipment-grounding
wire and NE M A 6-15 grounding
plug
(see figure). The plug must only be inserted into
a matching
receptacle that is properly installed and
grounded in accordance with local codes and ordinances.
For 220V Connection
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instrtucted to do so later
in this manual.
Extension Cords
We do not recommend using an extension cord with
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required
plug and receptacle, and
meet the following requirements:
Minimum Gauge Size at 220V ...................... 12 AWG
Maximum Length (Shorter is Better) ................50 ft.
Grounding Pin
Current Carrying Prongs
6-20 PLUG
GROUNDED
6-20 RECEPTACLE
Figure 5. NEMA 6-20 plug & receptacle.
No adapter should be used with the
required plug. If the plug does not fit
the available receptacle or the machine
must be reconnected to a different
type of circuit, the reconnection must
be made by an electrician or qualified
service personnel and it must comply
with all local codes and ordinances.
-15-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SETUP
SETUP
Unpacking
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Description Qty
• Additional People ....................................... 1-3
• Safety Glasses ......................................... 1 ea.
• Leather Gloves .................................. 1 Pair ea.
• Cleaner/Degreaser ............................ As Needed
• Disposable Rags ................................ As Needed
• Lifting Equipment (Min. 1000-lb Rating):
—Forklift or Hoist .........................................1
—Lifting Slings .............................................2
• Precision Straightedge 3' .................................1
• Phillips Screwdriver #2 ...................................1
• Dust-Collection System ...................................1
• 4" Dust Hose (length as needed) ........................1
• 4" Hose Clamp ..............................................1
Items Needed for Setup
The following items are needed, but not included, to set
up your machine.
SUFFOCATION HAZARD!
Immediately discard all
plastic bags and packing
materials to eliminate
choking/suffocation
hazards for children and
animals.
Wear safety glasses during
entire setup process!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual
to become familiar with
the controls and opera-
tions before starting the
machine!
HEAVY LIFT!
Straining or crushing
injury may occur from
improperly lifting the
machine or some of its
parts. To reduce this
risk, get help from other
people and use a forklift
(or other lifting equip-
ment) rated for weight of
machine.
-16-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SETUP
Inventory (Figures 6–7): Qty
A. Jointer Assembly ...........................................1
B. Lifting Hooks ...............................................2
C. Lock Washers 8mm (Lifting Hooks) .....................4
D. Cap Screws M8-1.25 x 20 (Lifting Hooks) ..............4
E. Fence Tilt Handle ..........................................1
F. Push Blocks .................................................2
G. Open-End Wrench 11/13mm .............................1
H. Open-End Wrench 8/10mm ..............................1
I. Hex Wrench 6mm ..........................................1
J. Knife-Setting Jig (W1859)
—E-Clips ....................................................4
—Knife Jig Feet ...........................................2
—Knife Jig Rod.............................................1
K. Helical Cutterhead Accessories (W1860)
—T-Handle Torx Driver T-25 .............................2
—Torx Screws T-25 #10-32 x
1
⁄2 ....................... 10
—Indexable Inserts 15 x 15 x 2.5mm ..................5
Inventory
Figure 6. Inventory—jointer assembly.
A
Figure 7. Inventory—loose items.
B
H
I
K
C
D
E
F
G
The following is a list of items shipped with your machine.
Before beginning setup, lay these items out and inventory
them.
Note:
If you cannot find an item on this list, carefully
check around/inside the machine and packaging materials.
Often, these items get lost in packaging materials while
unpacking or they are pre-installed at the factory.
J
-17-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SETUP
To prevent
corrosion during shipment and storage of your
machine, the factory has coated t
he bare metal surfaces
of your machine
with a heavy-duty rust prevention
compound
.
I
f you are unprepared or impatient, this compound can
be difficult to
remove. To ensure that the removal of this
coating is as easy as possible, please gather the correct
cleaner, lubricant, and tools listed below:
• Cleaner/degreaser
designed to remove storage wax
and grease
• Safety glasses & disposable gloves
•
Solvent brush or paint brush
• Disposable Rags
To
remove rust preventative coating, do these steps:
1.
DISCONNECT MACHINE FROM POWER!
2.
Put on safety glasses and disposable gloves.
3
. Coat the rust preventative with a liberal amount of
cleaner/degreaser, then let it soak for 5–10 minutes.
4
. Wipe off surfaces. If your cleaner/degreaser is
effective, the coating will wipe off easily.
Tip: An easier way to clean off thick coats of rust
preventative from flat surfaces is to use a PLASTIC
paint scraper to scrape off the majority of the
coating before wiping it off with your rag. (Do
not use a metal scraper or you may scratch your
machine.)
5
. Repeat cleaning steps as necessary until all of the
compound is removed.
6
. To prevent rust on freshly cleaned surfaces,
immediately coat with a quality metal protectant.
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.
Many cleaning solvents
are toxic if inhaled.
Minimize your risk
by only using these
products in a well
ventilated area.
In a pinch, automotive degreasers,
mineral spirits or WD•40 can be used
to remove rust preventative coating.
Before using these products, though,
test them on an inconspicuous area of
your paint to make sure they will not
damage it.
Cleaning Machine
-18-
Model W1859/W1860 (For Machines Mfd. Since 07/19)
SETUP
Figure 8. Working clearances.
Machine Placement
Wall
Min. 30"
for Maintenance
76"
25"
Weight Load
Refer to the
Machine Specifications for the
weight of your machine. Make sure that the
surface upon which the machine is placed will
bear the weight of the machine, additional
equipment that may be installed on the
machine, and the heaviest workpiece that will
be used. Additionally, consider the weight of
the operator and any dynamic loading that may
occur when operating the machine.
Space Allocation
Consider the largest size of workpiece that
will be processed through this machine and
provide enough space around the machine
for adequate operator material handling or
the installation of auxiliary equipment. With
permanent installations, leave enough space
around the machine to open or remove doors/
covers as required by the maintenance and
service described in this manual.
See below for
required space allocation.
Physical Environment
The physical environment where your machine is
operated is important for safe operation and the
longevity of its components. For best results,
operate this machine in a dry environment
that is free from excessive moisture, hazardous
chemicals, airborne abrasives, or extreme
conditions. Extreme conditions for this type
of machinery are generally those where the
ambient temperature range exceeds 41°–104°F;
the relative humidity range exceeds 20–95%
(non-condensing); or the environment is subject
to vibration, shocks, or bumps.
Electrical Installation
Place this machine near an existing power
source. Make sure all power cords are protected
from traffic, material handling, moisture,
chemicals, or other hazards. Make sure to leave
access to a means of disconnecting the power
source or engaging a lockout/tagout device.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed
safely. Shadows, glare, or strobe effects that
may distract or impede the operator must be
eliminated.
Children or untrained people
may be seriously injured by this
machine. Only install in an access
restricted location.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
Grizzly W1860 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Grizzly G0959 Owner's manual
-
Grizzly 15 in. Planer W1862 Owner's manual
-
Woodstock W1754H Owner's manual
-
-
Woodstock W1694 User manual
-
-
-
-
-
Other documents
-
Shop fox W1859 Owner's manual
-
-
-
-
-
-
South bend SB1113 Owner's manual
-
South bend SB1091 Owner's manual
-
King Canada KKC-60 User manual
-
Craftex CX Series CX06Z Owner's manual
