Land Pride RBT45 User manual

Brand: Land Pride

Model: RBT45

Type: User manual

This manual is also suitable for

RBT45 Series

Table of Contents

Cover photo may show optional equipment not supplied

with standard unit.

For an Operator’s Manual and Decal Kit in French

Language, please see your Land Pride dealer.

Read the Operator’s Manual entirely. When you see this symbol,

the subsequent instructions and warnings are serious - follow

without exception. Your life and the lives of others depend on it!

Rear Blades

RBT4596 & RBT45108

301-205M

Operator’s Manual

Printed 11/27/18

35106

11/27/18RBT4596 & RBT45108 Rear Blades 301-205M

Machine Identification

Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new

manual.

If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were

originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by

adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with

the Option(s) weight and measurements.

Dealer Contact Information

Model Number

Serial Number

Machine Height

Machine Length

Machine Width

Machine Weight

Delivery Date

First Operation

Accessories

Name:

Street:

City/State:

Telephone:

Email:

WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov

California Proposition 65

Table of Contents

11/27/18

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

RBT4596 & RBT45108 Rear Blades 301-205M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1

Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1

Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 6

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Section 1: Assembly & Set-Up . . . . . . . . . . . . 7

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . . 7

Weight & Horsepower . . . . . . . . . . . . . . . . . . . . . 7

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3-Point Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Hydraulic Outlets . . . . . . . . . . . . . . . . . . . . . . . . . 7

Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . 7

Tractor Shutdown Procedure . . . . . . . . . . . . . . . . . 7

Assembly & Set-Up Safety . . . . . . . . . . . . . . . . . . . 8

Hitch, Frame & Blade . . . . . . . . . . . . . . . . . . . . . . . 8

3-Point Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standard 3-Point Hook-Up . . . . . . . . . . . . . . . . . . 9

Quick Hitch Hook-Up . . . . . . . . . . . . . . . . . . . . . . 9

Blade Offset Cylinder . . . . . . . . . . . . . . . . . . . . . . 10

Blade Angling Cylinder . . . . . . . . . . . . . . . . . . . . . 10

Blade Tilting Cylinder . . . . . . . . . . . . . . . . . . . . . . 11

Section 2: Set-Up of Accessories . . . . . . . . . 12

Manual Offset, Angling and Tilting . . . . . . . . . . . . 12

Gauge Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Hydraulic Cushion Valve . . . . . . . . . . . . . . . . . . . . 14

Hydraulic Selector Valve . . . . . . . . . . . . . . . . . . . . 15

Skid Shoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

End Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Section 3: Adjustments . . . . . . . . . . . . . . . . . 17

Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Blade Offset Adjustment . . . . . . . . . . . . . . . . . . . . 17

Manual Offset . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Hydraulic Offset . . . . . . . . . . . . . . . . . . . . . . . . . 17

Blade Angle and Reversing . . . . . . . . . . . . . . . . . . 17

Manual Angle and Reversing . . . . . . . . . . . . . . . 17

Hydraulic Angle and Reversing . . . . . . . . . . . . . 17

Blade Tilt Adjustments . . . . . . . . . . . . . . . . . . . . . 18

Manual Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Hydraulic Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Gauge Wheel Depth Adjustments . . . . . . . . . . . . . 18

Manual Depth Control . . . . . . . . . . . . . . . . . . . . 18

Hydraulic Depth Control . . . . . . . . . . . . . . . . . . . 18

Blade Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Section 4: Operating Procedures . . . . . . . . . 19

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 19

General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Inspection After Hook-Up . . . . . . . . . . . . . . . . . . . 20

Transport With Rear Blade . . . . . . . . . . . . . . . . . . 20

Rear Blade Functions . . . . . . . . . . . . . . . . . . . . . . 21

Grading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Edge work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Ditch Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Backfilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Unhook Rear Blade . . . . . . . . . . . . . . . . . . . . . . . . 21

Basic Operating Instructions . . . . . . . . . . . . . . . . . 22

General Operating Instructions . . . . . . . . . . . . . . . 22

Section 5: Maintenance & Lubrication . . . . . 23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Tractor Maintenance . . . . . . . . . . . . . . . . . . . . . . . 23

Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 23

Ordering Replacement Parts . . . . . . . . . . . . . . . . . 23

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Blade Pivot Shaft . . . . . . . . . . . . . . . . . . . . . . . . 24

Blade Tilt Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Front Pivot Shaft . . . . . . . . . . . . . . . . . . . . . . . . 24

Moldboard and Blade . . . . . . . . . . . . . . . . . . . . . 24

Ratchet Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Gauge Wheel Front Pivot . . . . . . . . . . . . . . . . . . 25

Gauge Wheel Caster Tube . . . . . . . . . . . . . . . . . 25

Gauge Wheel Hub . . . . . . . . . . . . . . . . . . . . . . . 25

Section 6: Specifications & Capacities . . . . . 26

Section 7: Features & Benefits . . . . . . . . . . . 27

Section 8: Troubleshooting . . . . . . . . . . . . . . 28

Section 9: Torque Values Chart . . . . . . . . . . . 29

Section 10: Warranty . . . . . . . . . . . . . . . . . . . 31

Table of Contents Continued

11/27/18

Parts Manual QR Locator

The QR (Quick Reference) code on the

cover and to the left will take you to the

Parts Manual for this equipment.

Download the appropriate App on your

smart phone, open the App, point your

phone on the QR code and take a picture.

Dealer QR Locator

The QR code on the left will

link you to available dealers

for Land Pride products.

Refer to Parts Manual QR

Locator on this page for

detailed instructions.

RBT4596 & RBT45108 Rear Blades 301-205M

Table of Contents

See previous page for Table of Contents.

Important Safety Information

11/27/18

Important Safety Information

Listed below are common practices that may or may not be applicable to the products

described in this manual.



Tractor Shutdown & Storage

 If engaged, disengage power

take-off.

 Park on solid, level ground and

lower implement to ground or onto

support blocks.

 Put tractor in park or set park

brake, turn off engine, and remove

switch key to prevent unauthorized

starting.

 Relieve all hydraulic pressure to

auxiliary hydraulic lines.

 Wait for all components to stop

before leaving operator’s seat.

 Use steps, grab-handles and

anti-slip surfaces when stepping

on and off the tractor.

 Detach and store implement in an

area where children normally do

not play. Secure implement using

blocks and supports.

OFF

REMOVE

Look for the Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

potential hazard to personal safety involved and extra

safety precaution must be taken. When you see this

symbol, be alert and carefully read the message that

follows it. In addition to design and configuration of

equipment, hazard control, and accident prevention are

dependent upon the awareness, concern, prudence, and

proper training of personnel involved in the operation,

transport, maintenance, and storage of equipment.

Safety Precautions for

Children

Tragedy can occur if the operator

is not alert to the presence of

children. Children generally are

attracted to implements and their

work.

 Never assume children will remain

where you last saw them.

 Keep children out of the work area

and under the watchful eye of a

responsible adult.

 Be alert and shut the implement

and tractor down if children enter

the work area.

 Never carry children on the tractor

or implement. There is not a safe

place for them to ride. They may

fall off and be run over or interfere

with the control of the power

machine.

 Never allow children to operate the

power machine, even under adult

supervision.

 Never allow children to play on the

power machine or implement.

 Use extra caution when backing

up. Before the tractor starts to

move, look down and behind to

make sure the area is clear.

Safety at All Times

Careful operation is your best

assurance against an accident.

All operators, no matter how much

experience they may have, should

carefully read this manual and

other related manuals, or have the

manuals read to them, before

operating the power machine and

this implement.

 Thoroughly read and understand

the “Safety Label” section. Read

all instructions noted on them.

 Do not operate the equipment

while under the influence of drugs

or alcohol as they impair the ability

to safely and properly operate the

equipment.

 The operator should be familiar

with all functions of the tractor and

attached implement and be able to

handle emergencies quickly.

 Make sure all guards and shields

appropriate for the operation are in

place and secured before

operating implement.

 Keep all bystanders away from

equipment and work area.

 Start tractor from the driver’s seat

with hydraulic controls in neutral.

 Operate tractor and controls from

the driver’s seat only.

 Never dismount from a moving

tractor or leave tractor unattended

with engine running.

 Do not allow anyone to stand

between tractor and implement

while backing up to implement.

 Keep hands, feet, and clothing

away from power-driven parts.

 While transporting and operating

equipment, watch out for objects

overhead and along side such as

fences, trees, buildings, wires, etc.

 Do not turn tractor so tight as to

cause hitched implement to ride

up on the tractor’s rear wheel.

 Store implement in an area where

children normally do not play.

When needed, secure attachment

against falling with support blocks.

Be Aware of

Signal Words

A signal word designates a degree or

level of hazard seriousness. The

signal words are:

Indicates a hazardous situation that, if

not avoided, will result in death or

serious injury.

Indicates a hazardous situation that, if

not avoided, could result in death or

serious injury.

Indicates a hazardous situation that, if

not avoided, may result in minor or

moderate injury.

WARNING

CAUTION

DANGER

Important Safety Information

11/27/18

Listed below are common practices that may or may not be applicable to the products

described in this manual.

Practice Safe Maintenance

 Understand procedure before doing

work. Refer to the Operator’s

Manual for additional information.

 Work on a level surface in a clean

dry area that is well-lit.

 Lower implement to the ground and

follow all shutdown procedures

before leaving the operator’s seat to

perform maintenance.

 Do not work under any hydraulic

supported equipment. It can settle,

suddenly leak down, or be lowered

accidentally. If it is necessary to

work under the equipment, securely

support it with stands or suitable

blocking beforehand.

 Use properly grounded electrical

outlets and tools.

 Use correct tools and equipment for

the job that are in good condition.

 Allow equipment to cool before

working on it.

 Disconnect battery ground cable (-)

before servicing or adjusting

electrical systems or before welding

on implement.

 Inspect all parts. Make certain

parts are in good condition &

installed properly.

 Replace parts on this implement

with genuine Land Pride parts only.

Do not alter this implement in a way

which will adversely affect its

performance.

 Do not grease or oil implement

while it is in operation.

 Remove buildup of grease, oil, or

debris.

 Always make sure any material and

waste products from the repair and

maintenance of the implement are

properly collected and disposed.

 Remove all tools and unused parts

before operation.

 Do not weld or torch on galvanized

metal as it will release toxic fumes.

Use A Safety Chain

 A safety chain will help control

drawn machinery should it

separate from the tractor drawbar.

 Use a chain with the strength

rating equal to or greater than the

gross weight of the towed

implement.

 Attach the chain to the tractor

drawbar support or other specified

anchor location. Allow only

enough slack in the chain to

permit turning.

 Always hitch the implement to the

machine towing it. Do not use the

safety chain tow the implement.

Transport Safely

 Comply with federal, state, and

local laws.

 Use towing vehicle and trailer of

adequate size and capacity. Secure

equipment towed on a trailer with

tie downs and chains.

 Sudden braking can cause a towed

trailer to swerve and upset. Reduce

speed if towed trailer is not

equipped with brakes.

 Avoid contact with any overhead

utility lines or electrically charged

conductors.

 Always drive with load on end of

loader arms low to the ground.

 Always drive straight up and down

steep inclines with heavy end of a

tractor with loader attachment on

the “uphill” side.

 Engage park brake when stopped

on an incline.

 Maximum transport speed for an

attached equipment is 20 mph. DO

NOT EXCEED. Never travel at a

speed which does not allow

adequate control of steering and

stopping. Some rough terrains

require a slower speed.

 As a guideline, use the following

maximum speed weight ratios for

attached equipment:

20 mph when weight of attached

equipment is less than or equal

to the weight of machine towing

the equipment.

10 mph when weight of attached

equipment exceeds weight of

machine towing equipment but

not more than double the weight.

 IMPORTANT: Do not tow a load

that is more than double the weight

of the vehicle towing the load.

Tire Safety

 Tire changing can be dangerous

and must be performed by

trained personnel using the

correct tools and equipment.

 Always maintain correct tire

pressure. Do not inflate tires

above recommended pressures

shown in the Operator’s Manual.

 When inflating tires, use a clip-on

chuck and extension hose long

enough to allow you to stand to

one side and NOT in front of or

over the tire assembly. Use a

safety cage if available.

 Securely support the implement

when changing a wheel.

 When removing and installing

wheels, use wheel handling

equipment adequate for the

weight involved.

 Make sure wheel bolts have been

tightened to the specified torque.

Important Safety Information

11/27/18

Listed below are common practices that may or may not be applicable to the products

described in this manual.

Avoid High

Pressure Fluids Hazard

 Escaping fluid under pressure can

penetrate the skin causing serious

injury.

 Before disconnecting hydraulic

lines or performing work on the

hydraulic system, be sure to

release all residual pressure.

 Make sure all hydraulic fluid

connections are tight and all

hydraulic hoses and lines are in

good condition before applying

pressure to the system.

 Use a piece of paper or

cardboard, NOT BODY PARTS, to

check for suspected leaks.

 Wear protective gloves and safety

glasses or goggles when working

with hydraulic systems.

 DO NOT DELAY. If an accident

occurs, see a doctor familiar with

this type of injury immediately. Any

fluid injected into the skin or eyes

must be treated within

a few hours or

gangrene may

result.

Wear Personal Protective

Equipment (PPE)

 Wear protective clothing and

equipment appropriate for the job

such as safety shoes, safety

glasses, hard hat, and ear plugs.

 Clothing should fit snug without

fringes and pull strings to avoid

entanglement with moving parts.

 Prolonged exposure to loud noise

can cause hearing impairment or

hearing loss. Wear suitable

hearing protection such as

earmuffs or earplugs.

 Operating equipment safely

requires the operator’s full

attention. Avoid wearing

headphones while operating

equipment.

Use Seat Belt and ROPS

 Land Pride recommends the use

of a CAB or roll-over-protective-

structures (ROPS) and seat belt

in almost all power machines.

Combination of a CAB or ROPS

and seat belt will reduce the risk

of serious injury or death if the

power machine should be upset.

 If ROPS is in the locked-up

position, fasten seat belt snugly

and securely to help protect

against serious injury or death

from falling and machine overturn.

Keep Riders Off

Machinery

 Never carry riders on tractor or

implement.

 Riders obstruct operator’s view

and interfere with the control of

the power machine.

 Riders can be struck by objects or

thrown from the equipment.

 Never use tractor or implement to

lift or transport riders.

Avoid Underground

Utilities

 Dig Safe, Call 811 (USA).

Always contact your local utility

companies (electrical, telephone,

gas, water, sewer, and others)

before digging so that they may

mark the location of any

underground services in the area.

 Be sure to ask how close you can

work to the marks they positioned.

Prepare for Emergencies

 Be prepared if a fire starts.

 Keep a first aid kit and fire

extinguisher handy.

 Keep emergency numbers for

doctor, ambulance, hospital, and

fire department near phone.

911

Use Safety

Lights and Devices

 Slow moving tractors, skid steers,

self-propelled machines, and towed

equipment can create a hazard

when driven on public roads. They

are difficult to see, especially at

night. Use the Slow Moving Vehicle

sign (SMV) when on public roads.

 Flashing warning lights and turn

signals are recommended

whenever driving on public roads.

Important Safety Information

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

818-339C

Warning: High Pressure

818-487C

Danger Avoid Injury

35107

Safety Labels

Your Rear Blade comes equipped with all safety labels in place.

They were designed to help you safely operate your implement.

Read and follow their directions.

1. Keep all safety labels clean and legible.

2. Refer to this section for proper label placement. Replace

all damaged or missing labels. Order new labels from your

nearest Land Pride dealer. To find your nearest dealer,

visit our dealer locator at www.landpride.com.

3. Some new equipment installed during repair requires

safety labels to be affixed to the replaced component as

specified by Land Pride. When ordering new components

make sure the correct safety labels are included in the

request.

4. Refer to this section for proper label placement.

To install new labels:

a. Clean surface area where label is to be placed.

b. Spray soapy water on the surface where the label is to

be placed.

c. Peel backing from label. Press firmly onto the surface.

d. Squeeze out air bubbles with the edge of a credit card

or with a similar type straight edge.

Important Safety Information

RBT4596 & RBT45108 Rear Blades 301-205M11/27/18

Table of Contents

818-491C

Warning Pinch/Shear

35107

35106

35107

838-615C

2" x 9" Amber Reflector

(RBT45108 Only: On front left side of moldboard)

838-075C

Caution Falling Moldboard

838-614C

2" x 9" Red Reflector

(2 places on back side of moldboard)

Introduction

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

Owner Assistance

The dealer should complete the Online Warranty

Registration at the time of purchase. This information is

necessary to provide you with quality customer service.

The parts on your Rear Blade have been specially

genuine Land Pride parts. Contact a Land Pride dealer if

customer service or repair parts are required. Your Land

Pride dealer has trained personnel, repair parts, and

equipment needed to service the implement.

Serial Number

For quick reference and prompt service, record model

and serial number on the inside cover page and again on

the warranty page. Always provide model number and

serial number when ordering parts and in all

correspondences with your Land Pride dealer. For

location of your serial number plate, see Figure 1.

Serial Number Location

Figure 1

Further Assistance

Your dealer wants you to be satisfied with your new Rear

Blade. If for any reason you do not understand any part of

this manual or are not satisfied with the service received,

the following actions are suggested:

1. Discuss any problems you have with your implement

with your dealership service personnel so they can

address the problem.

2. If you are still not satisfied, seek out the owner or

general manager of the dealership, explain the

problem, and request assistance.

3. For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

lpser[email protected]

NOTE: A special point of information that the

operator should be aware of before continuing.

35107

Land Pride welcomes you to the growing family of new

product owners. This Rear Blade has been designed with

care and built by skilled workers using quality materials.

Proper assembly, maintenance, and safe operating

practices will help you get years of satisfactory use from

this machine.

Application

The Land Pride RBT45 Series 3-Way Hydraulic Rear

Blades are built tough from the ground up for applications

ranging from landscaping, construction, snow removal,

and feedlot cleaning. This blade is also ideal for ditching,

road grading, and all-around farm use.

They are designed for Category II or III 3-Point hitch

mounting, attachment to tractors in the 70 to 125 hp

range and are Quick Hitch compatible. The blade with its

reversible cutting edge can be angled left or right up to

, the ends can be tilted up or down by as much as 15

and the whole blade can be offset to the left or right by as

much as 35". The blade can also be rotated 180

for

blading in reverse with same angling, tilting, and offset

capabilities. A retractable parking stand is included to

accommodate easier blade removal, storage, and

reattachment.

Available accessories includes manual or hydraulic

operated single or dual gauge wheel for good depth

control, end plates for holding material, skid shoes for

blade protection and manual angling, offset, and tilting

links for tractors with only one or two duplex outlets.

See “Specifications & Capacities” on page 26 and

“Features & Benefits” on page 27 for additional

information.

Using This Manual

•

This Operator’s Manual is designed to help familiarize

you with safety, assembly, operation, adjustments,

troubleshooting, and maintenance. Read this manual

and follow the recommendations to help ensure safe

and efficient operation.

• The information contained within this manual was

current at the time of printing. Some parts may change

slightly to assure you of the best performance.

• To order a new Operator’s or Parts Manual, contact

your authorized dealer. Manuals can also be

downloaded, free-of-charge, from our website at

www.landpride.com

Terminology

“Right” or “Left” as used in this manual is determined by

facing forward in the direction the machine will operate

while in use unless otherwise stated.

Definitions

IMPORTANT: A special point of information related

to the following topic. Land Pride’s intention is this

information must be read & noted before continuing.

Introduction

Section 1: Assembly & Set-Up

RBT4596 & RBT45108 Rear Blades 301-205M11/27/18

Table of Contents

Tractor Requirements

Weight & Horsepower

WARNING

To avoid serious injury or death:

Do not hitch implement to a tractor rated outside the

recommended horsepower range. Doing so can bend and/or

break the implement.

Tractor rating should be between 70 - 125 horsepower.

Tractors above the maximum horsepower rating must not

be used. Excessive horsepower can damage the Rear

Blade. Never hitch a Rear Blade to a track type tractor.

Track type tractors can damage equipment.

Weight

WARNING

To avoid serious injury or death:

Lightweight tractors with rear attached implements may need

weights added to the front to maintain steering control.

Consult your tractor Operator’s Manual to determine proper

weight requirements and maximum weight limitations.

Tractor weight must be capable of controlling the

Rear Blade under all operating conditions. An

underweight tractor is difficult to steer. Do not use tractors

that are too light. See Important Note Below.

3-Point Hitch

A 3-Point Category ll or lII hitch is required. The lower

3-Point arms of the 3-Point hitch must be stabilized to

prevent side-to-side movement. Most tractors have sway

blocks or adjustable chains for this purpose.

Hydraulic Outlets

WARNING

To avoid serious injury or death:

Hydraulic fluid under high pressure can penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than hands

when searching for leaks. A doctor familiar with this type of

injury must treat the injury within a few hours or gangrene

may result. DO NOT DELAY.

The number of required hydraulic duplex outlets at the

tractor is dependent upon how the 3-Way Rear Blade is

set-up.

• No outlets are required if the 3-Way Rear Blade is

set-up with manual links and ratchet jacks only.

• One to three duplex outlets are required if the 3-Way

Rear Blade is set-up with any one or more of the

following hydraulic cylinders; Offset Cylinder, Tilt

Cylinder and Angle Cylinder. Each cylinder will require

a duplex outlet at the tractor.

Section 1: Assembly & Set-Up

• A fourth duplex outlet is required if a gauge wheel is

purchased with a hydraulic cylinder.

A Selector Valve Kit may be purchased through your local

Land Pride dealer if your tractor does not have the

required number of duplex outlets. The selector valve

provides a way to operate 2 hydraulic cylinders through

one duplex outlet at the tractor. See “Hydraulic Selector

Valve” on page 15 for Kit Part No. and assembly

instructions.

Torque Requirements

See “Torque Values Chart” on page 29 to determine

correct torque values when tightening hardware.

Tractor Shutdown Procedure

The following are basic tractor shutdown procedures.

Follow these procedures and any additional shutdown

procedures provided in your tractor Operator’s Manual

before leaving the operator’s seat.

1. Reduce engine speed and disengage power take-off

if engaged.

2. Park tractor and implement on level, solid ground.

3. Lower implement to ground or onto non-concrete

support blocks.

4. Put tractor in park or set park brake, turn off engine,

and remove switch key to prevent unauthorized

starting.

5. Relieve all hydraulic pressure to auxiliary hydraulic

lines.

6. Wait for all components to come to a complete stop

before leaving the operator’s seat.

7. Use steps, grab-handles and anti-slip surfaces when

stepping on and off the tractor.

Section 1: Assembly & Set-Up

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

Rear Blade Assembly

Figure 1-1

18767

SHIPPING BLOCK

DO NOT REMOVE UNTIL AFTER ALL HYDRAULIC

CYLINDERS AND/OR RATCHET JACK AND

MANUAL LINKS HAVE BEEN INSTALLED.

Assembly & Set-Up Safety

WARNING

To avoid serious injury or death:

Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

DANGER

To avoid serious injury or death:

• Always check all blade hardware for tightness before

moving or working around the unit. Make sure moldboard

pivot and tilt retaining hardware is tightened to the correct

torque. The moldboard can fall from the its pivot mount or

tilt mount if retaining hardware is loose or missing.

• Components falling from the implement can injure a

person. Make certain all components are secured to the

implement before lifting it, and that the unit is properly

supported on the ground before removing lifting device.

Always keep feet and other extremities clear of areas where

components can fall.

Hitch, Frame & Blade

Refer to Figure 1-1:

1. Locate shipping crate on a level surface. Remove &

separate blade assemblies from shipping crate.

2. Use a lifting device to set blade pivot assembly (#8)

upright. Remove bolts (#5), lock washers (#6) & pivot

cap (#9) from blade pivot assembly (#8). Do not

remove shipping block in the blade tilt housing.

3. Carefully insert blade pivot assembly (#8) into main

frame (#2) at a 90° angle to the frame.

4. Reinstall pivot cap (#9), lock washers (#6), and

3/4"-16 x 1 3/4" GR5 hex head cap screws (#5).

Tighten hardware to secure main frame to blade pivot

assembly.

5. Remove 3/4" x 4 3/8" hitch pin (#10) and rotate jack

stand (#11) to a vertical position. Re-insert pin with

lock pin.

6. Lower unit to ground and unhook lifting device.

7. Remove front pivot shaft (#3) from front hitch

assembly (#1) by removing 1/2" bolts (#4).

8. Secure front hitch assembly (#1) to a lifting device or

attach to a tractor. Refer to “3-Point Hook-Up” on

page 9.

9. Insert main frame (#2) into front hitch (#1) as shown.

Reinstall front pivot shaft (#3) and secure with

1/2"-13 x 1 1/2" GR5 bolts (#4). Tighten the hardware

to secure front pivot shaft (#3).

10. If not already done, attach unit to tractor 3-Point

hitch. The top 3-Point hitch pin and linchpin are to be

supplied by the customer. See Figure 1-2 for

category settings.

11. Re-check all hardware for tightness. Torque all bolts

to specifications as listed in the “Torque Values

Chart” on page 29.

12. Check blade pivot bolts (#5) and blade tilt bolts (#7)

for tightness. If needed, tighten bolts to the correct

torque.

Section 1: Assembly & Set-Up

RBT4596 & RBT45108 Rear Blades 301-205M11/27/18

Table of Contents

3-Point & Quick Hitch Hook-Up

Figure 1-2

35108

Linchpin

Hitch Pin

QH20 Quick Hitch

Mounting Holes

Upper Holes: Cat. II With Bushings or Cat.III Without Bushings

See step 8 on this page for additional information.

Coupling Storage

Slots (Both Sides)

37298

Cat. III Lower Hitch Pin

Cat. II Lower Hitch Pin Install 1

7/16" O.D. bushings when using

Land Pride’s QH20 Quick Hitch.

Parking Stand

3-Point Hook-Up

WARNING

To avoid serious injury or death:

Always shut tractor down using “Tractor Shutdown

Procedure” provided in this manual before allowing anyone

including the operator to hook-up and unhook implement.

DANGER

To avoid serious injury or death:

• A crushing hazard exists while hooking-up and unhooking

implement. Keep people and animals away while backing-

up to implement or pulling away from implement. Do not

operate hydraulic controls while a person or animal is

directly behind the power machine or near the implement.

• Always check all blade hardware for tightness before

moving or working around the unit. Make sure moldboard

pivot and tilt retaining hardware is tightened to the correct

torque. The moldboard can fall from the its pivot mount or

tilt mount if retaining hardware is loose or missing.

Standard 3-Point Hook-Up

Refer to Figure 1-2:

A 3-Point Category II or III hitch is required. The lower

3-Point arms of the 3-Point hitch must be stabilized to

prevent side-to-side movement. Most tractors have sway

blocks or adjustable chains for this purpose.

1. Shorten or remove tractor drawbar to keep it from

interfering with the Rear Blade.

2. Remove linchpins and hitch pins from clevis

lugs.Keep for reuse.

3. Slowly back tractor up to Rear Blade while using

tractor’s 3-Point hydraulic control to align hitch holes

in lower arms with implement’s hitch pin holes.

4. Engage tractor park brake, shut tractor engine off

and remove key before dismounting from tractor or

allowing someone else to hook-up the Rear Blade.

5. With tractor’s lower hitch arms aligned and

positioned in the clevises, insert hitch pins through

the clevis lugs and lower arm hitch holes. Secure

hitch pins with linchpins.

6. Ensure lower arms are stabilized to prevent

excessive side movement.

7. Refer to Figure 1-1 on page 8: Remove hitch

pin (#10) from parking stand (#11) and rotate stand

up. Reinsert hitch pin and secure with hairpin cotter.

8. Connect Cat. II top center link to upper holes using

customer supplied 1" clevis pin & linchpin. If top

center link is Cat. III, drive 1" x 1 1/4" x 1 5/8"

bushings out and connect center link to upper holes

using customer supplied 1 1/4" clevis pin & linchpin.

9. Manually adjust one of the two lower lift arms up or

down to level the Rear Blade from left to right.

10. Manually adjust length of top-link to level Rear Blade

front to rear.

11. Check clearances after all offset, pivot, and tilt

linkages have been installed. Refer to “Inspection

After Hook-Up” on page 20.

Quick Hitch Hook-Up

Refer to Figure 1-2:

The customer must purchase and install two

1.141" ID x 1.4375" OD x 2 1/2" long busings (Land Pride

Part No. 890-940C) on the lower hitch pins. Also, the

center hitch pin must be moved to the lower hitch holes.

Follow hook-up and unhooking instructions in the Quick

Hitch Operator’s manual when using a Quick Hitch.

NOTE: Land Pride’s Quick Hitch can be attached to

the tractor to provide quick and easy 3-point hook-

up and detachment. See your nearest Land Pride

dealer to purchase a Quick-Hitch.

Section 1: Assembly & Set-Up

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

Blade Angling Cylinder

Refer to Figure 1-4:

WARNING

To avoid serious injury or death:

Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

1. Position hydraulic cylinder (#3) with ports on top as

shown. Install two 90 degree elbows (#4) into the

cylinder ports as shown. Tighten as needed.

2. Screw 74" long hydraulic hose (#6) into elbow (#4) at

the cylinder base and tighten.

3. Screw 82" long hydraulic hose (#5) into elbow (#4) at

the cylinder rod end and tighten.

4. Thread adapter fittings (#7) to the other end of the

hydraulic hoses and tighten. (Customer to supply

quick disconnect hydraulic couplings.)

5. Attach hydraulic cylinder to the lugs on the right side

of the frame with clevis pins (#1). Make sure

hydraulic ports are positioned on top and the cylinder

base in positioned to the front as shown.

6. Secure clevis pins with hair pin cotters (#2).

7. Route hoses through hose bracket located on the

right side of the front hitch. Connect hoses to tractor's

hydraulic system.

Hydraulic Blade Angling

Figure 1-4

IMPORTANT: Attach cylinder base to the front

cylinder mount. The base will interfere with the

mainframe if attached to rear cylinder mount.

24994

Customer to supply Quick Disconnect Couplings.

Blade Offset Cylinder

Refer to Figure 1-3:

WARNING

To avoid serious injury or death:

Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

Assemble hydraulic hoses to the hydraulic cylinder

before placing cylinder on the blade.

1. Position hydraulic cylinder (#3) with ports on top as

shown. Install two 90 degree elbows (#4) into the

cylinder ports as shown. Tighten as needed.

2. Screw 74" long hydraulic hose (#6) into elbow (#4) at

the cylinder base and tighten.

3. Screw 82" long hydraulic hose (#5) into elbow (#4)

located at the cylinder rod end and tighten.

4. Thread adapter fittings (#7) to the other end of the

hydraulic hoses and tighten. (Customer to supply

quick disconnect hydraulic couplings.)

5. Attach hydraulic cylinder to lugs located on left side of

3-Way Rear Blade with clevis pins (#2). Make sure

hydraulic ports are positioned on top and the cylinder

base in positioned to the front as shown.

6. Secure clevis pins with hair pin cotters (#1).

7. Route hoses through hose bracket located on the

right side of the front hitch. Connect hoses to tractor's

hydraulic system.

Hydraulic Blade Offsetting

Figure 1-3

IMPORTANT: Attach cylinder base to the front

cylinder mount. The base will interfere with the

mainframe if attached to rear cylinder mount.

24993

Customer to supply Quick Disconnect Couplings.

Section 1: Assembly & Set-Up

RBT4596 & RBT45108 Rear Blades 301-205M11/27/18

Table of Contents

Blade Tilting Cylinder

Refer to Figure 1-5:

WARNING

To avoid serious injury or death:

• Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic

cylinders have been installed and cylinders have been

charged with oil.

• The Rear Blade may be unstable and hard to control until

all the hydraulic cylinders have been purged with oil.

IMPORTANT: The blade tilt cylinder receives a 90

degree elbow with a small orifice in one end of the

elbow. Make sure this orifice elbow is installed in the

cylinder port at the rod end of the tilt cylinder.

IMPORTANT: Attach cylinder base to the upper

cylinder mount. The base will interfere with the

moldboard if attached to the lower cylinder mount.

Hydraulic Blade Offsetting and Angling

Figure 1-5

24995

SHIPPING BLOCK

DO NOT REMOVE UNTIL AFTER ALL HYDRAULIC

CYLINDERS, RATCHET JACKS AND/OR MANUAL

LINKS HAVE BEEN INSTALLED.

Customer to supply Quick

Disconnect Couplings (#8).

1. Install a 90 degree elbow (#5) with 3/32" orifice (#4)

into the cylinder port located at the rod end as shown.

Tighten as needed.

2. Install a second 90 degree elbow (#6) without an

orifice into the cylinder port located at the base

shown. Tighten as needed.

3. Screw 111" long hydraulic hoses (#7) into

elbows (#5 & #6) and tighten.

4. Thread adapter fittings (#8) to the other end of the

hydraulic hoses and tighten. (Customer to supply

quick disconnect hydraulic couplings.)

5. Attach hydraulic cylinder (#3) to the lugs at the back

of the blade with clevis pins (#2). Make sure hydraulic

ports are positioned on the back and the cylinder

base is mounted to the center lug as shown.

6. Secure clevis pins with hair pin cotters (#1).

7. Route hoses through hose brackets located on the

main frame and hitch. Connect hoses to tractor's

hydraulic system.

8. Remove shipping block at this time.

Section 2: Set-Up of Accessories

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

Manual Offset, Angling and Tilt

Figure 2-1

24999

Blade Angling

Blade Offset

Blade Tilting

SHIPPING BLOCK

DO NOT REMOVE UNTIL AFTER ALL

HYDRAULIC CYLINDERS AND/OR

RATCHET JACK AND MANUAL LINKS

HAVE BEEN INSTALLED.

Section 2: Set-Up of Accessories

Manual Offset, Angling and Tilting

Kit Bundles

300-206A. . . . . . MANANUAL ANGLE LINK ASSEMBLY

300-206A. . . . . MANANUAL OFFSET LINK ASSEMBLY

890-637C . . . . . . . . . . . RATCHET JACK 16.25 - 22.25

The manual links and ratchet jack may be used in place

of the hydraulic cylinders.

WARNING

To avoid serious injury or death:

Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

Blade Angling Manual Link

Refer to Figure 2-1:

1. Attach manual angling links (#3 & #4) to the right side

of the Rear Blade as shown with two 1" clevis

pins (#1). Secure with hair pin cotters (#5).

2. Adjust blade angle by removing hitch pin (#2) and

moving outer link (#3) to a different hole. Replace

hitch pin and secure with hair pin cotter (#5).

Blade Offset Manual Link

Refer to Figure 2-1:

1. Attach manual offset links (#3 & #4) to the left side

of the Rear Blade as shown with two 1" clevis

pins (#1). Secure with hair pin cotters (#5).

2. Adjust offset angle by removing hitch pin (#2) and

moving outer link (#3) to a different hole. Replace

hitch pin and secure with hair pin cotter (#5).

Blade Tilting Ratchet Jack

Refer to Figure 2-1:

1. Attach ratchet jack (#6) to the back side of the Rear

Blade as shown with two 1" clevis pins (#1). Secure

with hair pin cotters (#5).

2. Adjust blade tilt by setting the lock on the ratchet

lever and pumping the lever back and forth to raise

one end of the blade higher than the other end.

Reposition ratchet lock and pump lever back and

forth to tilt blade in the opposite direction.

3. Remove shipping block after ratchet jack (#6) has

been installed.

Section 2: Set-Up of Accessories

RBT4596 & RBT45108 Rear Blades 301-205M11/27/18

Table of Contents

Hydraulically Controlled Gauge Wheel

Figure 2-2

24996

Customer to supply Quick

Disconnect Couplings.

Ratchet Jack Set-Up

1. Attach ratchet jack (#19) to the mounting lugs on the

gauge wheel arm (#3) and mounting bracket (#11)

with two 1" clevis pins (#20). Secure pins with hair pin

cotters (#21).

Hydraulic Cylinder Set-Up

1. Position hydraulic cylinder (#15) with ports on top as

shown. Thread 90 degree elbows (#13) into the two

ports and tighten.

2. Screw 116" long hydraulic hoses (#14) to the elbows

and tighten.

3. Thread hydraulic couplings (#18) to the other end of

hydraulic hoses and tighten. (Customer to supply

quick disconnect hydraulic couplings.)

4. Attach hydraulic cylinder to the lugs on the gauge

wheel with two 1" clevis pins (#17). Make sure

hydraulic ports are positioned on top and cylinder

base is located to the front as shown.

5. Secure clevis pins with hair pin cotters (#16).

6. Route hoses through the hose brackets located on

the top of the main frame and right side of the front

hitch. Connect hoses to tractor's hydraulic system.

IMPORTANT: Attach cylinder base to the front

mounting lug. The base will interfere with the gauge

wheel arm if attached to the rear mounting lug.

Gauge Wheel

Kit Bundles

301-225A. . . . . . HYDRAULIC SINGLE GAUGE WHEEL

301-236A. . . . . . . .HYDRAULIC DUAL GAUGE WHEEL

301-281A. . . . . . . . .MANUAL SINGLE GAUGE WHEEL

301-282A. . . . . . . . . . MANUAL DUAL GAUGE WHEEL

Refer to Figure 2-2::

1. Attach gauge wheel mounting bracket (#11) to Rear

Blade frame with two 3/4"-10 x 10 1/2" GR5 hex head

bolts (#8) and 3/4" hex nuts (#10). Tighten nuts to

correct torque.

2. Insert gauge wheel hitch tube (#9) in gauge wheel

arm (#3).

3. Attach gauge wheel arm (#3) to mounting

bracket (#11) with 3/4"-10 x 10 1/2" GR5 hex head

bolt (#8) and 3/4" hex nut (#10). Tighten nut to correct

torque.

4. Insert gauge wheel caster assembly (single wheel

caster #1) or (dual wheel caster #2) in gauge wheel

arm (#3) and retainer washer (#4). Secure caster

assembly with 1/2" x 2 1/2" long roll pin (#5).

5. Attach center floating link (#12) to the front hitch with

1 1/4" x 1 3/4" hitch pin (#7). Secure with hair pin

cotter (#6).

Section 2: Set-Up of Accessories

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

Hydraulic Cushion Valve Assembly

Figure 2-3

24997

Customer to supply Quick

Disconnect Couplings.

Blade Ange Cylinder

Blade Offset Cylinder

Hydraulic Cushion Valve

Kit Bundles

301-235A . . . . . . . . . 96" - CYLINDER CUSHION VALVE

301-234A . . . . . . . . 108" - CYLINDER CUSHION VALVE

CAUTION

To avoid minor or moderate injury:

Do not operate Rear Blade with angling or offset cylinder fully

extended. Fully extending either cylinder will keep cushion

valves from operating correctly.

Refer to Figure 2-3:

1. Mount cushion valves (#1 & #2) onto mounting plate

with 3/8"-16 x 4" GR5 hex head cap screws (#3),

spring lock washers (#4) and hex nuts (#5). Tighten

hex nuts to correct torque.

2. Screw eight fittings (#6) into cushion valves (#1 & #2)

until tight.

3. Attach hydraulic hose (#7) to the right rear fitting of

cushion valve (#2) as shown.

4. Attach hydraulic hose (#8) to the right front fitting of

cushion valve (#1) as shown.

5. Attach hydraulic hose (#9) to the left rear fitting of

cushion valve (#1) as shown.

6. Attach hydraulic hose (#10) to the left front fitting of

cushion valve (#2) as shown.

7. Attach four hydraulic hoses (#11) included with this

option to the remaining cushion valve fittings (#6) and

thread through the hose retainer (#12).

Section 2: Set-Up of Accessories

RBT4596 & RBT45108 Rear Blades 301-205M11/27/18

Table of Contents

Hydraulic Selector Valve

Kit Bundle

301-227A . . . . . . . . . . Double Selector Valve Assembly

Refer to Figure 2-4:

An optional hydraulic selector valve kit may be purchased

that bolts to the front hitch frame. This kit provides a way

to operate 2 cylinders at one outlet, thereby reducing the

number of required outlets at the tractor by one. See also

“Tractor Requirements” on page 7.

1. Remove existing two bolts (#4) and discard.

2. Attach selector mount (#9) to the top of the hitch with

two new 1/2"-13 x 2" GR5 hex head cap screws (#4),

flat washers (#5), spring lock washers (#6), and hex

nuts (#7). Tighten nuts to the correct torque.

3. Attach double selector valve (#3) to selector

mount (#9) with two 3/8"-16 x 3" GR5 hex head cap

screws (#8), spring lock washers (#10), and hex

nuts (#11). Tighten nuts to the correct torque.

Hydraulic Selector Valve Assembly

Figure 2-4

24998

Customer to supply Quick

Disconnect Couplings.

4. Apply teflon tape to the pipe threads of the three

3/4 x 1/2MNPT elbows (#1) and screw them into the

double selector valve as shown. Tighten to correct

orientation.

5. Apply teflon tape to the threads of the three

3/4JIC x 1/2MNPT adapters (#13) and screw them

into the double selector valve until tight.

6. Attach three 3/4JIC x 3/4JIC elbows (#12) to the

adapters (#13). Tighten to correct orientation.

7. Attach blade offset hydraulic hoses (#14) to the

bottom elbows.

8. Attach hydraulic hoses (#15) from one of the other

cylinders to the top elbows.

9. Attach tractor connected hydraulic hoses (#2) to the

side elbows.

10. Thread hydraulic adapters onto hydraulic hoses (#2)

and tighten. (Customer to supply quick disconnect

hydraulic couplings.)

Section 2: Set-Up of Accessories

RBT4596 & RBT45108 Rear Blades 301-205M 11/27/18

Table of Contents

Skid Shoe

Kit Bundle (Pair of skid shoes)

301-333A. . . . . . . . . . . . . . . . . SKID SHOE ASSEMBLY

Refer to Figure 2-5:

The skid shoes are attached to both ends of the blade to

help prevent damage to the surface of the ground by the

blade.

1. Remove two 5/8"-11 x 1 3/4" GR5 plow bolts (#1)

from the end of the blade. Keep hardware for

installation of skid shoes.

2. Attach skid shoe bracket (#3) with 5/8"-11 x 1 3/4"

GR5 plow bolts (#1), flat washers (#2), and hex

flange locknuts (#4). Tighten hardware to the correct

torque.

3. Insert skid shoe (#5) into skid shoe bracket (#3).

Secure with bent pin (#6) and hairpin cotter (#7).

4. Repeat steps 1 through 3 for the other side.

Skid Shoe Assembly

Figure 2-5

25535

End Plates

Kit Bundle (Pair of End Plates)

301-147A. . . . . . . . . . . . . . . . . . . . . . . . . .END PLATES

Refer to Figure 2-6:

End plates are attached to both ends of the blade,

eliminating spillage when moving snow or loose material.

1. Attach right-hand end plate (#3) to the moldboard as

shown with two 5/8"-11 x 2" GR5 hex head cap

screws (#4), spring lock washer (#7), and hex nuts

(#8). Draw hex nuts up snug. Do not tighten.

2. Attach side plate support strap (#2) with two

1/2"-13 x 1 1/4" GR5 hex head cap screws (#1), lock

washers (#5), and hex nuts (#6). Draw hex nuts up

snug. Do not tighten

3. First tighten hex nuts (#8) to the correct torque and

then next nuts (#6) last.

4. Repeat steps 1 through 3 for the left-hand end plate.

End Plate Assembly

Figure 2-6

NOTE: Alternate tightening of bolts when installing

mounting hardware. Some deflection may occur in

moldboard.

12550

Page is loading ...

Land Pride RBT45 User manual

Brand: Land Pride

Model: RBT45

Type: User manual

This manual is also suitable for

RBT45 Series

Download PDF

report

Land Pride RBT45 User manual

This manual is also suitable for

Land Pride RBT45 User manual

Related papers

Other documents