Land Pride 3rd User manual

Type
User manual
© Copyright 2019 Printed
1
Figure 1
Notes
1. This manual is written with the assumption that the
tractor is not supplied with rear remotes or backhoe.
2. This valve kit is designed to operate hydraulic
cylinders.
3. For further assistance write to:
Land Pride Service Department
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address: [email protected]
Assembly Instructions
Assembly Instructions
Initial Preparations
1. Park tractor on a flat surface, place gear shift lever in
park, turn off engine, and remove ignition key.
Valve Assembly
Refer to Figure 1 & Figure 2:
1. Attach valve assembly support bracket (#1) to
existing holes “C” on right-hand side of loader frame
with M18-2.5 x 100 bolts (#7), 3-1/4" long tube (#3),
3-1/2" long tube (#4), flat washers (#11), and
nuts (#9) as shown. Tighten nuts (#9) to the correct
torque.
2. Route hydraulic hoses (#16 & #22) under the tractor
platform and rearward toward the loader valve.
37026
113 9
C
1
7
114 97
For color photos, visit
https://dealers.landpride.com/en/12036/dealer-training
and look for “Third Function Valves.”
Figure 2
Connect Hydraulic Hoses to Power
Beyond Ports
1. Place chocks in front and back of tractor's left rear
wheel.
2. Loosen lug nuts on right rear wheel. Do not remove
lug nuts at this time.
3. Jack right rear wheel off the ground and place a jack
stand under the right rear axle.
4. Lower right rear axle onto the jack stand. The rear
wheel should be slightly off the ground. Make sure
jack stand is secure and will not slip out from under
the tractor axle.
5. Remove lug nuts and right rear wheel.
6. Locate and remove the steel tube that is connected
to the power beyond port.
37027
Right-
Hand Side
Left-Hand
Side
Attach to
positive (+)
post on the
tractor battery
IMPORTANT: Land Pride recommends that your
dealer connect hydraulic hoses (#16 & #22) to your
tractor’s power beyond ports. Improper hook-up
could cause damage to your tractor or valve.
For B2320 Kubota Tractors with LA304 Loader,
B2620 Kubota Tractors with LA364 Loader, and
B2301 & B2601 Kubota Tractors with LA434 Loader
Manual No. 380-151M
Third Function Valve Kit #380-149A
Installation Instructions
5/3/19
Assembly Instructions
Third Function Valve Kit #380-149A Installation Instructions Manual No. 380-151M 5/3/19
2
Figure 3
Refer to Figure 3:
7. Screw the larger hydraulic adapter (#14) to power
beyond port at the loader valve until tight.
8. Screw elbow (#15) to adapter (#14) until tight.
9. Locate 48" long hose (#22) attached to “P” port in
valve (#13). Screw hose to elbow (#15) until tight.
10. Locate port on right-hand side of tractor where steel
tube in step 6 was removed. Screw the smaller
hydraulic adapter (#23) or 90
o
adapter (#25) to this
port until tight.
11. Locate 62" long hose (#16) attached to “T” port in
valve (#13). Screw hose to adapter (#23) or 90
o
adapter (#25)until tight.
12. Secure hoses (#16 & #22) to underside of tractor with
cable ties (#5).
13. Install right rear wheel and snug-up wheel lug nuts.
14. Jack axle up and remove jack stand.
15. Lower tractor down and tighten rear wheel lug nuts in
a crisscross pattern. Refer to tractor Operator's
Manual for proper torque value.
16. Remove chocks.
17. Check tractor hydraulic fluid level. If low, add
recommended hydraulic fluid. Refer to your tractor
Operator's Manual for recommended hydraulic fluid
and procedure for checking hydraulic fluid level.
37027
Right-
Hand Side
Left-Hand
Side
Attach to
positive (+)
post on the
tractor battery
NOTE: Depending on tractor model and/or options,
the seat support frame may need to be removed to
performing the following steps.
NOTE: Depending on tractor model and/or options,
either straight adapter (#23) or 90
o
adapter (#25)
will be used.
Figure 4
Control Lever Assembly
Refer to Figure 3 & Figure 4:
1. Remove existing knob (not shown) from end of
control lever “D”.
2. Install new joystick (#17) over end of control lever “D”
with push buttons facing operator as shown.
3. Tighten set screws (#6) against control lever. Tighten
jam nuts (#8) to secure set screws (#6).
4. Thread joystick wiring harness (#18) through
hole “E” beneath rubber floor mat.
Refer to Figure 3:
5. Reference Connections “A”: Connect one
black wire in harness (#18) to one black wire in
harness (#25) and the other black wire in
harness (#18) to one white wire in harness (#25).
6. Reference Connection “B”: Connect the two red
wires from joystick (#17) to wire (#20) on one end of
fuse holder (#19).
7. Connect wire (#20) on opposite end of fuse
holder (#19) to the positive (+) post on the tractor
battery.
Refer to Figure 4:
8. Secure wiring with cable ties (#5) as needed.
37028
17
6 8
D
5
E
18
Push Buttons
Assembly Instructions
5/3/19 Third Function Valve Kit #380-149A Installation Instructions Manual No. 380-151M
3
Figure 5
Cross Beam Mount Assembly
Refer to Figure 3 on page 2 & Figure 5:
1. Orient as shown and attach bulk head mount (#2) to
the right-hand side of loader crossbeam “F” with
u-bolt (#12) and hex whiz nuts (#10). Tighten hex
whiz nuts to the correct torque.
Refer to Figure 3 on page 2, Figure 5, & Figure 6:
2. Route hoses (#24) along loader arm and through
loader hose loop bracket “G” to the third function
valve assembly (#13).
3. Connect hoses to quick couplers (#21) on
“A” & “B” ports of valve block (#13).
4. Secure hydraulic hoses (#24) as needed with
cable ties (#5).
37029
2
12
10
24
F
Figure 6
37030
24
G
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Land Pride 3rd User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI