Sharp MX-7081 Operating instructions

Functions of the machine and procedures

for placing originals and loading paper

BEFORE USING THE MACHINE

COPIER

Using the copy function

PRINTER

Using the printer function

FACSIMILE

Using the fax function

SCANNER / INTERNET FAX

Using the scan / Internet fax function

DOCUMENT FILING

Storing jobs as files on the local drive

SETTING MODE

Configuring settings to make the

machine easier to use

Click to jump to the table of contents of the

desired chapter.

User's Manual

DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM

MODEL: MX-7081

MX-8081

MANUAL FINISHING

Using the manual finishing function

i

HOW TO USE THIS MANUAL

Click a button below to move to the page that you wish to view.

The following explanation assumes that Adobe Acrobat Reader is being used (Some buttons do not appear in the

default state.).

(1) Return to top page button

If an operation does not proceed as expected, click this

button to start over again.

(2) Back one page button

Displays the previous page.

(3) Forward one page button

Displays the next page.

(4) Return to previously displayed page button

Displays the page that was displayed before the current

page.

(5) Title button

Displays the page of the title indicated by the button.

(6) Contents button

Displays the contents of each chapter.

For example, if the current page is part of the printer

chapter, the table of contents of the printer chapter

appears.

(1) (2) (3) (4)

(6)

(5)

(6)

(5)

If a button does not appear, refer to Adobe Reader Help to display the button.

ii

ABOUT OPERATION MANUAL

This manual explains how to use the MX-7081/MX-8081 digital full colour multifunctional system.

Please note

• For information on installing the drivers and software cited in this manual, please refer to the Software Setup Guide.

• For information on your operating system, please refer to your operating system manual or the online Help function.

• The explanations of screens and procedures in a Windows environment are primarily for Windows

®

10. The screens may be

different depending on the version of the operating system or the software application.

• The explanations of screens and procedures for use in a macOS environment generally assume that macOS 10.12 is being

used and a PPD driver is installed. The screens may be different depending on the version of the operating system or the

software application.

• Wherever "MX-xxxx" appears in this manual, please substitute your model name for "xxxx".

• This manual contains references to the fax function. However, please note that the fax function is not available in some

countries and regions.

• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please

contact your dealer or nearest authorised service representative.

• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem

is discovered, please contact your dealer or nearest authorised service representative.

• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its

options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due

to use of the product.

Warning

• Reproduction, adaptation or translation of the contents of the manual without prior written permission is prohibited, except as

allowed under copyright laws.

• All information in this manual is subject to change without notice.

Illustrations and the operation panel and touch panel shown in this manual

The peripheral devices are generally optional, however, some models include certain peripheral devices as standard equipment.

The explanations in this manual assume that a multi bypass tray, large capacity tray, saddle stitch finisher, punch module, paper

pass unit and curl correction unit is installed on the MX-8081.

For some functions and procedures, the explanations assume that devices other than the above are installed.

Icons used in the manuals

The icons in the manuals indicate the following types of information:

The display screens, messages, and key names shown in the manual may differ from those on the actual machine

due to product improvements and modifications.

This alerts you to a situation that could result in

death or serious personal injury. This alerts

you to a situation that could result in personal

injury or damage to properties.

This explains how to stop or correct an operation.

This alerts you to a situation where there is a

risk of machine damage or failure.

This describes a routine work relevant to setting mode.

This supplements function or operation

procedure.

1-1

BEFORE USING THE MACHINE

PART NAMES AND FUNCTION . . . . . . . . . . . . . . . 1-3

• EXTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

• INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

• AUTOMATIC DOCUMENT FEEDER AND

DOCUMENT GLASS. . . . . . . . . . . . . . . . . . . . . 1-7

• SIDE AND BACK. . . . . . . . . . . . . . . . . . . . . . . . 1-8

• OPERATION PANEL. . . . . . . . . . . . . . . . . . . . . 1-9

TURNING ON THE POWER. . . . . . . . . . . . . . . . . . . 1-10

HOME SCREEN AND PREVIEW SCREEN. . . . . . . 1-11

• HOME SCREEN . . . . . . . . . . . . . . . . . . . . . . . . 1-11

• PREVIEW SCREEN . . . . . . . . . . . . . . . . . . . . . 1-14

Eco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21

• ECO FUNCTIONS OF THE MACHINE . . . . . . . 1-21

• AUTO POWER SHUT-OFF MODE . . . . . . . . . . 1-22

• PREHEAT MODE . . . . . . . . . . . . . . . . . . . . . . . 1-23

• AS SOON AS THE REMOTE JOB IS

FINISHED, ENTER AUTO POWER SHUT OFF

MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23

• ECO SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25

• Energy Saving Pattern List . . . . . . . . . . . . . . . . 1-26

• Power ON/OFF Schedule Setting . . . . . . . . . . . 1-27

• Specific Date Operation Settings. . . . . . . . . . . . 1-28

• DISPLAYING ECO RECOMMENDATION

SETTINGS (ECO RECOMMENDATION

FUNCTION DISPLAY). . . . . . . . . . . . . . . . . . . . 1-29

• Toner Save Mode . . . . . . . . . . . . . . . . . . . . . . . 1-29

USER AUTHENTICATION . . . . . . . . . . . . . . . . . . . . 1-30

• AUTHENTICATION BY USER NUMBER . . . . . 1-30

• AUTHENTICATION BY LOGIN

NAME/PASSWORD . . . . . . . . . . . . . . . . . . . . . 1-32

• QUICK AUTHENTICATION. . . . . . . . . . . . . . . . 1-35

User Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38

• User List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38

• Default Settings . . . . . . . . . . . . . . . . . . . . . . . . 1-42

• Administration Settings. . . . . . . . . . . . . . . . . . . 1-46

• Actions when the user is authenticated . . . . . . 1-47

• Card Reader Settings. . . . . . . . . . . . . . . . . . . . 1-48

• Pages Limit Group . . . . . . . . . . . . . . . . . . . . . . 1-49

• Machine Page Limit Setting . . . . . . . . . . . . . . . 1-49

• Authority Group . . . . . . . . . . . . . . . . . . . . . . . . 1-50

• Favourite Operation Group. . . . . . . . . . . . . . . . 1-54

• User Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-56

•

ACTIVE DIRECTORY LINKING FUNCTION . . .

1-58

BILLING CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-62

• BILLING CODE . . . . . . . . . . . . . . . . . . . . . . . . 1-62

• USE BILLING CODE . . . . . . . . . . . . . . . . . . . . 1-63

• REGISTERING A NEW BILLING CODE . . . . . 1-66

• EDITING OR DELETING THE REGISTERED

BILLING CODE . . . . . . . . . . . . . . . . . . . . . . . . 1-69

• Billing Code Setting . . . . . . . . . . . . . . . . . . . . . 1-72

EASILY CONNECT WITH AN NFC-COMPATIBLE

MOBILE DEVICE (EASY CONNECT). . . . . . . . . . . 1-75

• CONNECTING BY NFC . . . . . . . . . . . . . . . . . . 1-75

• CONNECTING BY QR CODE . . . . . . . . . . . . . 1-76

• Easy Connection Setting . . . . . . . . . . . . . . . . . 1-77

NAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-78

REMOTE OPERATION OF THE MACHINE . . . . . . 1-80

UNIVERSAL DESIGN IN THE MACHINE. . . . . . . . 1-82

• UNIVERSAL DESIGN RELATED TO

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 1-82

•

UNIVERSAL DESIGN RELATED TO VISION . . .

1-83

•

UNIVERSAL DESIGN RELATED TO HEARING . . .

1-83

•

UNIVERSAL DESIGN FEATURES. . . . . . . . . . . . . .

1-84

ITEMS RECORDED IN THE JOB LOG . . . . . . . . . 1-86

PRINTING A MANUAL FROM THE OPERATION

PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-88

BEFORE USING THE MACHINE

1-2

BEFORE USING THE MACHINE

LOADING PAPER

IMPORTANT POINTS ABOUT PAPER . . . . . . . . . . 1-89

• When a large capacity tray is installed . . . . . . . 1-89

• THE DEFINITION OF "R" IN PAPER SIZE . . . . 1-90

• APPLICABLE PAPER TYPES. . . . . . . . . . . . . . 1-91

LOADING PAPER IN THE TRAY 1/2. . . . . . . . . . . . 1-94

LOADING PAPER IN THE TRAY 3/4. . . . . . . . . . . . 1-97

LOADING PAPER IN THE LARGE CAPACITY

TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-102

LOADING PAPER IN THE LARGE CAPACITY

TRAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-107

LOADING PAPER INTO THE BYPASS TRAY . . . . 1-112

HOW TO PLACE THE LONG PAPER GUIDE. . . . . 1-120

• PAPER SETTINGS IN THE SYSTEM

SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-121

HOW TO PLACE THE ORIGINAL

SELECTING A PROCEDURE FOR PLACING THE

ORIGINAL DEPENDING ON THE TYPE AND

STATUS OF THE ORIGINAL. . . . . . . . . . . . . . . . . . 1-125

AUTOMATIC DOCUMENT FEEDER . . . . . . . . . . . . 1-127

PREVENTIVE LIGHT TO INDICATE ORIGINAL

LEFT BEHIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-130

DOCUMENT GLASS . . . . . . . . . . . . . . . . . . . . . . . . 1-131

PERIPHERAL DEVICES

PERIPHERAL DEVICES . . . . . . . . . . . . . . . . . . . . . 1-133

FINISHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-135

• PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . 1-135

• HOW TO STAPLE MANUALLY. . . . . . . . . . . . . 1-136

• SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-137

• FINISHER MAINTENANCE. . . . . . . . . . . . . . . . 1-137

FINISHER (LARGE STACKER). . . . . . . . . . . . . . . . 1-139

• PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . 1-139

• SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-140

• REPLACING THE CARTRIDGE . . . . . . . . . . . . 1-140

SADDLE STITCH FINISHER . . . . . . . . . . . . . . . . . 1-144

• PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . 1-144

• HOW TO STAPLE MANUALLY . . . . . . . . . . . . 1-145

• SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-146

•

SADDLE STITCH FINISHER MAINTENANCE. . .

1-147

SADDLE STITCH FINISHER (LARGE STACKER) . . .

1-151

•

PART NAMES. . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-151

• SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-152

• REPLACING THE CARTRIDGE . . . . . . . . . . . 1-152

PUNCH MODULE (MX-PN16B/C/D). . . . . . . . . . . . 1-160

• DISCARDING PUNCH WASTE . . . . . . . . . . . . 1-160

PUNCH MODULE (MX-PN13A/B/C/D) . . . . . . . . . . 1-162

• DISCARDING PUNCH WASTE . . . . . . . . . . . . 1-162

FOLDING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-164

• PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . 1-164

INSERTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-165

• PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . 1-165

STATUS INDICATORS . . . . . . . . . . . . . . . . . . . . . . 1-166

• PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . 1-166

Sharp OSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-167

• APPLICATION COMMUNICATION . . . . . . . . . 1-167

• EXTERNAL ACCOUNT APPLICATION . . . . . . 1-168

• Sharp OSA Settings . . . . . . . . . . . . . . . . . . . . . 1-170

REMOVING MISFEEDS

REMOVING MISFEEDS . . . . . . . . . . . . . . . . . . . . . 1-174

MAINTENANCE

REGULAR MAINTENANCE . . . . . . . . . . . . . . . . . . 1-175

• CLEANING THE DOCUMENT GLASS AND

AUTOMATIC DOCUMENT FEEDER. . . . . . . . 1-175

• CLEANING THE LASER UNIT. . . . . . . . . . . . . 1-178

• CLEANING THE BYPASS FEED ROLLER . . . 1-182

• CLEANING THE PAPER FEED ROLLER . . . . 1-182

REPLACEMENT OF TONER CARTRIDGE . . . . . . 1-183

REPLACING THE WASTE TONER BOTTLE. . . . . 1-187

REPLACING THE STAMP CARTRIDGE . . . . . . . . 1-188

1-3

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

PART NAMES AND FUNCTION

EXTERIOR

(1) Output tray (centre tray)*

Received faxes and printed papers are delivered to this

tray.

(2) USB connector (A type)

This is used to connect a USB device such as a USB

memory device to the machine.

Supports USB 2.0 (Hi-Speed).

(3) Keyboard*

Use this as a substitute for the soft keyboard displayed

on the touch panel. When not being used, it can be

stored under the operation panel.

(4) Automatic document feeder

This automatically feeds and scans multiple originals.

Both sides of 2-sided originals can be automatically

scanned at one time.

► AUTOMATIC DOCUMENT FEEDER (page 1-127)

(5) Toner cover (Upper front cover)

Open this cover to replace the toner cartridge or to

remove misfed paper in the paper pass unit.

►

REPLACEMENT OF TONER CARTRIDGE (page 1-183)

(6) Front cover

Open this cover to switch the main power switch to "On" or "Off".

► TURNING ON THE POWER (page 1-10)

(7) Operation panel

This panel hosts the [Power] button, [Power Save]

button/indicator, [Home Screen] button/indicator, main

power indicator and touch panel. Use the touch panel to

operate each of these functions.Use the touch panel to

operate each of these functions.

An NFC touch point area also appears.

► OPERATION PANEL (page 1-9)

(8) Tray 1

Store paper in this tray. Up to 1200 sheets can be stored.

► LOADING PAPER IN THE TRAY 1/2 (page 1-94)

(9) Tray 3

Store paper in this tray. Up to 500 sheets can be stored.

► LOADING PAPER IN THE TRAY 3/4 (page 1-97)

(10) Tray 4

Store paper in this tray. Up to 500 sheets can be stored.

► LOADING PAPER IN THE TRAY 3/4 (page 1-97)

(11) Tray 2

Store paper in this tray. Up to 800 sheets can be stored.

► LOADING PAPER IN THE TRAY 1/2 (page 1-94)

*Optional

BEFORE USING THE MACHINE

(8) (9) (10) (11)

(1) (2) (3) (4) (5) (6) (7)

1-4

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

(12) Finisher*

This staples paper. A punch module can also be installed

to punch holes in output paper.

► FINISHER (page 1-135)

(13) Saddle stitch finisher*

This staples and folds paper. A punch module can also

be installed to punch holes in output paper. You can also

perform stapling manually.

► SADDLE STITCH FINISHER (page 1-144)

(14) Status indicator*

The status of the machine is indicated.

► STATUS INDICATORS (page 1-166)

(15) Right tray*

As required, paper can be output into the right tray.

Outputting received fax printouts into the right tray allows

you to separate them from other printed paper.

(16) Bypass tray

Use this tray to feed paper manually.

When loading paper larger than A4R or 8-1/2" × 11"R,

pull out the extension guide.

► LOADING PAPER INTO THE BYPASS TRAY (page

1-112)

(17) Punch module*

This punches and outputs paper.

(18) Tray 5 (MX-LC12)*

Store paper in this tray. Up to 3500 sheets can be stored.

(19) Tray 5 (MX-LCX3 N)*

Store paper in this tray. Up to 3000 sheets can be stored.

*Optional

(18)(17) (19)

(12) (13)

(15) (16)

(14)

1-5

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

(20) Finisher (large stacker)*

This staples paper. A punch module can also be installed

to punch holes in output paper.

► FINISHER (LARGE STACKER) (page 1-139)

(21) Saddle stitch finisher (large stacker)*

This staples and folds paper. A punch module can also

be installed to punch holes in output paper. You can also

perform stapling manually.

► SADDLE STITCH FINISHER (LARGE STACKER)

(page 1-151)

(22) Punch module (MX-PN13A, MX-PN13B, MX-PN13C,

MX-PN13D)*

This punches and outputs paper.

(23) Inserter*

Covers and insertion sheets to be inserted into printed

sheets can be loaded.

Using the manual finishing function, you can directly feed

paper into the finisher or saddle stitch finisher to staple,

punch or fold the paper.

(24) Bypass tray*

Use this tray to feed paper manually.

When loading paper larger than A4R or 8-1/2" × 11"R,

pull out the extension guide.

► LOADING PAPER INTO THE BYPASS TRAY (page

1-112)

(25) Trimming module*

This trims the excess of saddle-stitched output.

(26) Folding unit*

This folds and outputs paper.

(27) Curl correction unit*

This punches and outputs paper.

(28) Paper pass unit*

This feeds paper to the machine.

(29) Large capacity trays*

Store paper in this tray. Up to 2500 sheets can be stored

in each tray.

► LOADING PAPER IN THE LARGE CAPACITY

TRAYS (page 1-107)

*Optional

(25) (26) (27) (28) (29)

(23)(20) (21) (24)(22)

1-6

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

INTERIOR

(1) Toner cartridge

This cartridge contains toner.

When the toner in a cartridge runs out, the cartridge of

the colour that ran out must be replaced.

► REPLACEMENT OF TONER CARTRIDGE (page

1-183)

(2) Fusing unit

Heat is applied here to fuse the transferred image onto

the paper.

(3) Right side cover

Open this cover to remove a misfeed.

(4) Paper reversing section cover

This unit is used for reversing paper when 2-sided printing

is performed. Open this cover to remove a paper misfeed.

(5) The main power switch

Use this switch to turn on the power for the machine.

When using the fax or Internet fax functions, always keep

this switch in the " " position.

► TURNING ON THE POWER

(page 1-10)

(6) Waste toner bottle

This bottle collects excess toner that is produced during

printing.

► REPLACING THE WASTE TONER BOTTLE (page

1-187)

(7) Transfer belt

This belt takes the image formed with toner off the

photoconductive unit and transfers the image onto paper.

(8) Right side cover release lever

To remove a paper misfeed, pull and hold this lever up to

open the right side cover.

(1) (2) (3)

(5) (6) (8)(7)

(4)

The fusing unit is hot. Take care not to burn yourself

when removing a misfeed.

A service technician collects replaced waste toner

bottles.

Do not touch or damage the transfer belt.

This may cause a defective image.

1-7

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

AUTOMATIC DOCUMENT FEEDER AND DOCUMENT

GLASS

(1) Document feeding cover

Open this cover to remove an original misfeed.

► CLEANING THE PAPER FEED ROLLER (page

1-182)

(2) Original guides

These guides help ensure that the original is scanned

correctly.

Adjust the guides to the width of the original.

(3) Document feeder tray

Place the original.

Place the original with the print side facing up.

► AUTOMATIC DOCUMENT FEEDER (page 1-127)

(4) Original exit tray

The original is discharged to this tray after scanning.

(5) Original setting indicator

This indicator lights up when originals are placed on the

document feeder tray.

► AUTOMATIC DOCUMENT FEEDER (page 1-127)

(6) Scanning area

Originals placed in the automatic document feeder tray

are scanned here.

► CLEANING THE DOCUMENT GLASS AND

AUTOMATIC DOCUMENT FEEDER (page 1-175)

(7) Original size detector

This unit detects the size of an original placed on the

document glass.

► DOCUMENT GLASS (page 1-131)

(8) Document glass

If you want to scan books or other thick originals that

cannot be fed through the automatic document feeder,

place them on this glass.

► DOCUMENT GLASS (page 1-131)

(1) (3)

(6)(5) (7) (8)

(2) (4)

1-8

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

SIDE AND BACK

(1) USB connector (A type)

This is used to connect a USB device such as a USB

memory device to the machine.

Supports USB 2.0 (Hi-Speed).

(2) USB connector (B type)

Cannot be used.

(3) LAN connector

Connect the LAN cable to this connector when the

machine is used on a network.

Use a shielded LAN cable.

(4) External telephone line socket

When the fax function of the machine is used, an

extension phone can be connected to this jack.

(5) Telephone line jack

When the fax function of the machine is used, the

telephone line is connected to this jack.

(6) Power plug

(1)

(3)

(2)

(6)

(4)

(5)

Facsimile expansion kit

(Option)

1-9

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

OPERATION PANEL

This section describes the names and functions of the respective parts of the operation panel.

(1) Main power indicator

This lamp lights up when the machine's main power

switch is in the " " position.

► TURNING ON THE POWER (page 1-10)

(2) [

Power

] button

Use this button to turn the machine's power on and off.

► TURNING ON THE POWER (page 1-10)

(3) [Power Save] button/indicator

Use this button to set the machine to Sleep mode for

energy saving.

[Power Save] button blinks when the machine is in Sleep

Mode.

► AUTO POWER SHUT-OFF MODE (page 1-22)

(4) USB connector (A type)

This is used to connect a USB device such as a USB

memory device to the machine. For the USB cable, use a

shielded cable. Supports USB 2.0 (Hi-Speed).

(5) Touch panel

Messages and keys appear on the touch panel display.

Operate the machine by directly tapping the displayed

keys.

► HOME SCREEN (page 1-11)

(6) [Home Screen] key

Use this button to display the home screen.

► HOME SCREEN (page 1-11)

(4) (5) (6) (7)

(2) (3)(1)

[Home Screen] key

Use your finger to touch the [Home Screen] key.

If you use a pen or other tool to touch the key, it may not operate properly.

Risk of malfunctioning if you use with jewelry or other accessories.

You can change the angle of the touch panel.

1-10

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

TURNING ON THE POWER

This section describes how to turn on/off the machine's power and how to restart the machine.

Operate two power switches: the main power switch inside the front cover, located in the lower left corner, and the

[Power] button on the operation panel.

Turning on the power

• Turn the main power switch to the " " position.

• When the main power indicator lights in green, press the [Power] button.

Turning off the power

Turn off the power by pressing the [Power] button, then turn the main power switch to the " " position.

Restart the machine

Turn off the power by pressing the [Power] button and then press it again to turn on the power.

• When turning off the main power switch, press the [Power] button on the operation panel and then turn the main power

switch to the " " position.

In a sudden case of main power outage, turn the power for the machine back on and then turn it off in the correct order.

If the machine is left for a long time with the main power having been turned off prior to the [Power] button being turned off,

abnormal noises, degraded image quality or other problems may result.

• Turn off both the [Power] button and the main power switch and unplug the power cord if you suspect a machine failure, if

there is a bad thunderstorm nearby, or when you are moving the machine.

• When using the fax or Internet fax function, always keep the main power switch in the " " position.

• In order for some settings to take effect, the machine must be restarted. In some states of the machine, restarting with the

[Power] button may not make the settings take effect. In this case, turn off the main power switch and then turn it on again.

Main power indicator

[Power] button

The main power switch

1-11

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

HOME SCREEN AND PREVIEW SCREEN

HOME SCREEN

Pressing the [Home Screen] key on the operation panel displays the home screen on the touch panel. The home screen

displays the keys for selecting modes or functions.

For procedures for adding and deleting shortcut keys, see "User's Manual (Touch Panel Operation)".

To set the home screen for each "Favourite Operation Group List":

In "Settings (administrator)", select [User Control] →[Access Control Settings] → [Favourite Operation Group] → [Home

Screen List].

Perform this setting when user authentication is used.

Toner Quantity

M

C

Bk

Y

Operation

Guide

Enlarge

Display Mode

Settings Total Count Brightness

Adjustment

Job Status

Easy

Copy

Easy

Scan

Sharp OSA

Easy

Copy

Easy

Scan

File Retrieve

Sharp OSA

LINE PRINTER

Job Status

10:15 AM

Tray Settings

Tap a mode to change to

that mode.

►Changing mode

from the mode display

(page 1-13)

Select shortcut keys for

modes or functions.

►Changing mode

from the Home

screen (page 1-13)

Use these keys to select

functions that make the

machine easier to use.

Displays the machine's status other than the job

using icons.

► Icon indicating the status of the machine (page

1-12)

Displays the job in

progress or waiting with

text or icon.

Select functions that can

be utilized in respective

modes.

Tap the tab, and the list of

function keys is

displayed.

Switch the pages for

displaying shortcut keys.

Displays the time.

1-12

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

Icon indicating the status of the machine

* Contact your dealer or nearest authorised service representative.

Icon Machine status Icon Machine status

Printer data is being processed. A USB device is installed.

Printer data is being printed. The field support system is enabled.

Send data exists. Single-byte alphanumeric character entry

Forward error data exists. A data security kit is installed.

Received data exists. Connecting to the access point (Level 4)

Received confidential fax data exists. Connecting to the access point (Level 3)

Received data is held. Connecting to the access point (Level 2)

Received preview data exists. Connecting to the access point (Level 1)

OSA communication is in progress. Not connected to the access point

Enlarge display mode is enabled. Bad connection of the wireless LAN device in

the machine

*

Eco mode is enabled. Waiting for the access point

A maintenance notification is issued. A LAN cable is not connected.

Remote operation is in progress.

1-13

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

CHANGING MODES

Changing mode from the Home screen

Changing mode from the mode display

Toner Quantity

M

C

Bk

Y

Operation

Guide

Enlarge

Display Mode

Settings Total Count LCD Control Job Status

Easy

Copy

Easy

Scan

Easy

Fax

Easy

Copy

Easy

Scan

File Retrieve

Sharp OSA

LINE PRINTER

Job Status

10:15 AM

Print Release

Press the [Home Screen] key.

Tap the mode icon.

CA

Preview

Copies

Start

Color

Start

Original

8½x11

Paper

Select

Tray 1 1 → 1

2-Sided Copy Copy Ratio Staple / Punch

100% Off

Detail

LINE PRINTER

Easy

Copy

Easy

Scan

File Retrieve

Sharp OSA

Job Status

B/W

8½x11

CA

Preview Auto Set

Original

8½x11

Address

Address Book

Sending History

Global

Address Search

Local Drive/

USB

Detail

LINE PRINTER

Easy

Copy

Easy

Scan

File Retrieve

Sharp OSA

Job Status

Start

Color

Start

B/W

E-mail Address

Tap on the mode display.

CA

Preview Auto Set

Original

Address Fax Number

Detail

LINE PRINTER

Easy

Copy

Easy

Scan

File Retrieve

Sharp OSA

Job Status

Start

Color

Start

Address Book

Local Drive/

USB

8½x11

Select the mode.

Network Folder

Easy Fax

Easy Scan

Easy Copy

Fax E-Mail

FTP/Desktop

Internet Fax

B/W

Tap the key that shows .

Tap for any mode desired.

For procedures for editing the home screen, see "User's Manual (Touch Panel Operation)".

• Mode Key Display Setting

In "Settings (administrator)", select [System Settings] → [Common Settings] → [Operation Settings] → [Mode Key Display

Setting].

Configure settings for the display of mode keys at the top of the screen.

• Modes to Display

Select the mode keys that you want to display.

• Display Mode Keys on Home

You can enable display of the mode keys in the home screen as well.

1-14

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

PREVIEW SCREEN

In the preview screen, you can view output images or images stored in the machine using the touch panel.

Keys used in the preview screen

* Can also be used in Easy mode.

This changes the mode to edit mode.

Pages of the original can be changed,

rotated, or deleted.

* This rotates the preview image of whole

page in the arrow's direction. The

printing result is not rotated.

* This reduces the image.

,

* This displays preview images of

respective pages.

* This displays the scroll bar for

enlargement/reduction operations.

Moving the slider to the left reduces the

image, and moving the slider to the right

enlarges the image.

This displays thumbnails of preview

images.

* This enlarges the image. * This displays pages in a 3D view.

• The display position of an image can be moved by dragging it while it is enlarged.

• To enlarge an image, double-tap it when the preview image is displayed by page.

B/W

Start

Colour

Start

Preview

Scan

Again

CA

Start

Colour

Start

Send as well as print

Scan Original Again

Without change Settings

Store Data in Folder

Register Current Settings

File

Proof Copy

Program Registration

Store Data Temporarily

Quick File

CA

B/W

In Easy mode In Normal mode

1-15

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

Preview Setting

Configure preview settings and settings such as specifying thumbnail view as the default setting for display of Document

Filing and other files.

In "Settings (administrator)", select [System Settings] → [Common Settings] → [Operation Settings] → [Condition

Settings] → [Preview Setting].

Received Data Image Check Setting

Select whether or not a preview of received faxes and Internet faxes is shown. This is displayed when a facsimile

expansion kit or Internet fax expansion kit is installed.

Default List/Thumbnail Display

• Fax/I-Fax Reception Data: Select whether the default display format of the received fax/I-Fax

list screen is list or thumbnails.

• File Retrieve of Main Folder/Quick File Folder: Select whether the default display format of the document filing main

folder and temporary folder screens is list or thumbnails.

• File Retrieve of Custom Folder: Select whether the default display format of the document filing

custom folder screen is list or thumbnails.

• File Retrieve of Direct Print: Select whether the default state of the folder screen for direct print

shows the folders as a list or as thumbnails.

“Fax/I-Fax Reception Data” in “Received Data Image Check Setting” and “Default List/Thumbnail Display” can also be set

using [Received Data Image Check Setting] and [Default List/Thumbnail Display] in “Settings (administrator)” – [System

Settings] → [Image Send Settings] → [Common Settings] → [Condition Settings] → [Preview Setting].

1-16

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

Deleting a page

1

In the preview screen, tap to switch to edit mode.

2

Tap the page you want to delete, and

tap .

• You can also delete the page by tapping [Delete the Page] on the action panel.

• You can also delete the page by dragging a page to .

• To undo the deletion, tap . To redo the deletion, tap .

3

Tap the [Edit End] key.

5

Edit End

Move the Page

Rotate 180 Degrees

Specify Chapter Inserts

Insert Blank Page

Delete the Page

Erase Specified Original Area

Erase Specified Range

523 41

5

Edit End

Cancel and ReturnSelect the location to move.

21 3 4 5

4

Edit End

Move the Page

Rotate 180 Degrees

Insert Blank Page

Delete the Page

Erase Specified Original Area

Erase Specified Range

4321

1-17

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE

Moving a page

Rotating a page

1

In the preview screen, tap to switch to edit mode.

2

Tap the page you want to move, and

drag to move the page.

You can also move the page by tapping [Move the Page] on the action panel and then tap of the destination.

3

Tap the [Edit End] key.

1

In the preview screen, tap to switch to edit mode.

2

Tap the page you want to rotate, and

drag or to rotate the page.

You can also rotate the page by tapping [Rotate 180 Degrees] (Copy mode only) or [Rotate 90 Degrees] (Fax and

scanner mode only) on the action panel.

3

Tap the [Edit End] key.

6

Edit End

4 5321

6

Edit End

4 5321

Page is loading ...

Sharp MX-7081 Operating instructions

This manual is also suitable for

Sharp MX-7081 Operating instructions

Related papers

Other documents