BodyPerfect JFIRE Owner's manual

Brand: BodyPerfect

Model: JFIRE

Category: Treadmills

Type: Owner's manual

Treadmill

Retain this owner’s manual for future reference

Read and follow all instructions in this owner’s manual

Version A

Owner’s Manual

Model No: JFIRE

T H E F I T N E S S E Q U I P M E N T

- 1 -

INDEX

1. OVERVIEW DRAWING.........................................錯誤! 尚未定義書籤。

2. IMPORTANT SAFETY INSTRUCTIONS..................................................3

3. GROUNDING INSTRUCTIONS ................................................................4

4. PRE-ASSEMBLY CHECK LIST............................錯誤! 尚未定義書籤。

5. ASSEMBLY STEPS................................................錯誤! 尚未定義書籤。

6. CAUTION ...............................................................錯誤! 尚未定義書籤。

7. MAINTENANCE....................................................錯誤! 尚未定義書籤。

8. COMPUTER OPERATION INSTRUCTIONS.......錯誤! 尚未定義書籤。

- 2 -

1. OVERVIEW DRAWING

電源線

底座

機台主架

安全插銷/夾子

電子錶

過載保護開關

電源開關

Computer

Safety Key/ Clip

Power Switch

Circuit Breaker

Power Cord

Frame

Base

- 3 -

2. IMPORTANT SAFETY INSTRUCTIONS

When using this product, basic precautions should always be followed, including the following:

Please read the instruction carefully before starting to use this product.

Danger – To reduce the risk of electric shock：

1. Always unplug this product from the electrical outlet immediately after using and before

cleaning the treadmill.

Warning – To reduce the risk of burns, fire, electric shock, or physical injury：

1. The product should never be left unattended while plugged in.

Unplug the product from the outlet when not in use or before putting on or taking off the

clothes and other belongings.

2. To avoid any danger, close supervision is necessary when this production is used by children,

invalids or disabled persons. So it is when the machine is working with such persons around.

3. Be sure to use the product only for its intended use as described in this manual. Do not use any

attachment not recommended by the manufacturer in order to avoid any danger or accidents。

4. Never operate the product if it has a damaged cord or plug, if it is not working properly, if it

has been damaged, or dropped into water. Please return the product to the service center of

seller for examination and repair.

5. Do not carry this product by the supply cord or use the cord as a handle。

6. Keep the cord away from hot surfaces or ground。

7. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc。

8. Never drop or insert any objects into any vent of the treadmill。

9. Do not use or operate outdoors。

10. Do not operate where aerosol (spray) products are being used or where oxygen is thin。

11. Before turning the product power off, turn all controls to the off position then remove the plug

from the outlet。

12. Connect the product to a properly grounded outlet only。

13. If the power cord is damaged, be sure to ask the manufacturer for replacement to avoid

accidents .The seller and correlative qualified professionals are as well as eligible。

- 4 -

3. GROUNDING INSTRUCTIONS

The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a

path of least resistance for electric current to reduce the risk of electric shock.

The product is equipped with a cord having an equipment-grounding conductor and a grounding

plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Danger – Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or serviceman if you doubt whether the products

are properly grounded. Do not modify the plug provided with the product – if it will not fit the

outlet, have a proper outlet install by a qualified electrician.

The products is for use on normal 220V~240V and has circuit and contains a plug that looks like

the one illustrated in the figure. Make sure that the product is connected to an outlet having the

same configuration as the plug.

No adapter should be used with the product.

Figure

Grounding methods

GROUNDED

OUTLET

- 5 -

4. PRE-ASSEMBLY CHECK LIST

ITEM Description Qty ITEM Description Qty

Computer Console

1 a Hex Screw M8xP1.25x15 12

Frame

1 b Washer Ø8xØ16x1.5t 12

Left Handrail

1 c Hex Screw M8xP1.25x60 4

D Right Handrail 1 d Philips Screw M5xP0.8x18 4

E Cover 2 e SILICON 1

F Decoration Cover (Left) 1 f Hex Wrench 5mm(80mmx80mm) 1

Decoration Cover (Right)

1 g Hex Wrench 6mm(80mmx80mm) 1

Towel

1 h Safety Key/Clip 1

- 6 -

5. ASSEMBLY STEPS

Two persons are required to finish the assembly

steps.

(Caution!! Please follow exactly the assembly

steps below to avoid injury.)

1. Tighten the lower Control Wire of Frame

(B) with the Guide Thread attached in

Right Upright (D) , then pull it into the

Upright and clip the control wire with Wire

Clip, then insert it into the Upright as the

direction the round picture shows in the

right drawing.

2. After finished the above steps, put the Left

and Right Upright (C, D) on Frame and

tighten with Hex Screw (a), Washer (b) as

the right drawing shows.

Ps.1. To avoid danger, always assemble the

treadmill with more than two workers, do

not assemble by yourself.

Ps.2. When assembling the upright, make sure

one person holds the upright to avoid

falling.

3. After tightened the left and right handrails,

pull the control wire out of the Upright and

put the Computer Console above the

Upright. Then connect the control wire of

Frame with corresponding wire of

Computer console (A). After that, tighten

with Hex Screw (c) as the right drawing

shows.

Ps.1. To avoid danger, always assemble the

treadmill with more than two workers, do

not assemble by yourself.

Ps.2. While fastening screws, make sure that the

control wire of the tube isn’t damaged.

- 7 -

4. After finished the above steps, insert

Cover (E) to the above of Handrail.

After that, fix the left and right Decoration

Cover (F, G) to Frame as the right drawing

shows and tighten with Philips Screw (d).

- 8 -

6. Caution

Note: Thy Cylinder contains high pressure

gas. Please avoid crash with other

objects to avoid danger.

Note: If the Cylinder is hit, it might be

damaged and cause the usage not

smooth. The treadmill might fall

while folding.

This treadmill has the foldable mechanism for

storage. Stop all the movements (including stop the

running belt and take off the power cord) before

storage, then fold the main frame as the direction

shown in the right picture. Be sure the fixing plate

inserts the tube of base frame. On the contrary, if

you want to use treadmill, step on the fixing plate

as the direction shown in the right drawing. When

it disjoins from tube of base frame, pull down the

main frame as shown at the right drawing. Please

stand beside the treadmill and the main frame will

be slowly landing to the ground automatically.

( Ps.1. To prevent from danger, be careful if the

kids are around. If you want to move the

treadmill, fold the treadmill at first, hold the

rear adjust cap with your hands, then lean the

treadmill and do not move the treadmill until

the roller can be moved smoothly.)

(Ps.2. Do not move the treadmill on uneven

ground.)

(Ps.3. To avoid the injury, do not stand under the

frame when the frame is descending.)

- 9 -

7. MAINTENANCE

1. If the belt tends to move off the center, stop the treadmill.

Take the Hex Wrench 6mm and adjust the Hex Screw in the

Rear End Cap. For example, if the running belt is moving

towards the left side, tighten the left Hex Screw about 1/4

turn(clockwise); if the running belt is moving towards the

right side, tighten the right Hex Screw about 1/4

turn(clockwise); Turn on the treadmill after it has been

adjusted. If you find that the belt has not moved to the proper

position, please repeat the steps above. Don’t use the treadmill

until the running belt returns to the center position.

(Ps.1. This action is very important, if the belt is not in the

center, be sure to follow above steps.)

(Ps.2. The position of running belt might not stay precisely in

the center with slightly towards the left and right sides,

and the situation varies with how end-users use and the

weight of end-users. No need to adjust the belt if it doesn’t

rub against the parts aside.)

2. Depending on the usage of the product, please apply

SILICON on the board according to the below chart. Use

the Hex Wrench 6mm to unscrew the bolt inside the Rear

Roller. Then pull the belt up and daub some SILICON to

the center of the board. After that, adjust the belt to the

center of the deck, followed by tightening the screw to the

original set.

(Ps. When the belt is sliding, please follow the above method

to lubricate the running belt. )

Speed(KGS) Interval

1~6 km 1 year

6~12 km 6 months

12~16 km 3 months

- 10 -

8. COMPUTER OPERATION INSTRUCTIONS

I. General Operation

1. Turn on the treadmill

2. Put the safety key in the recess of the console.

The beeper will sound. At this time, all windows will display the values. The preset values are

0，not blinking which means this treadmill has entered start/ready status. Under this status,

user can hold the grip pulse sensor to detect heart rate value directly.

** If the safety key/clip is not placed in the recess of the console, the TIME window will display

“----”, which means the treadmill can not work normally.

** During exercise, if the safety key/clip is off, then the beeper will sound for warning, then the

treadmill will stop operation. At this moment, put the safety key back to the recess of console, then

all the values will go back to initial values.

** Under START/READY state, if you do not hold the grip pulse sensor, then PULSE window

will display HP, when you hold the both sides of grip pulse sensor, you will see the PULSE

window display the heart rate values.

** PULSE range：40~240 Beats/min

- 11 -

** It will show the relationship that whether the amount of the running is adequate under different

age and heart rate.

170

OVER

150 166

MIDDLE

120 146 162 LOW

117 143 157

114 137 153

111 135 149

108 131 145

105 128 140

102 124 136

99 120 132

96 116

HEART BEATS/MIN

20 25 30 35 40 45 50 55 60 65 (Age)

1. Press to start treadmill, the treadmill will start with a speed of 1.0km/hr, at this time

press or to increase/ decrease speed (or you can press

to control the speed) ,when press , the treadmill will stop ( press once, all the

values will stop changing, the treadmill will pause for 4 minutes and then come back to the

START/ READY position, if press once, then press the second time and hold it for 3

seconds, treadmill will automatically Reset to the START/READY position.)

2. This treadmill has no-segment angles adjustment function. Press

or to control

the incline angles of the treadmill, press and hold the or button, treadmill will

change angles accordingly, when reach the angles you need, just release the buttons then

the treadmill elevation will stop changing.

**Speed Range

：

1~16 km/hr

，

Step is 0.2 km/hr

- 12 -

II. MODE Operation Instruction (Under Function Selection Mode, press “ or

＂

switch among

MANUAL,

P1~P5 and HRC LED.

1. Under this mode ,you can set the time and distance freely, the operation method is shown

below:

1.1. Press ，and you will see the MANUAL LED light linking, press to enter

the MANUAL mode.

1.2. At this time, you can press or to set the time. After finished, press

to start running, or press to set the distance.

pre-set value: 20 min

Range of time：5~99 min，Step is 1 min.

1.3. At this time, you can press or to set the distance. After finished, press

to start running, or press to go back to the options in the Mode pattern.

Pre-set value: 5 km

Range of distance：1~9.9 km，Step is 0.1 km.

P1~P5

Program Control Function

(each

PROGRAM

has 12 segments)

2.1. When the

MANUAL

LED begin to flash, you can press

“

＂

until the desired LED of

P1~P5

begin to flash, press to confirm, after you enter the

program control function, the corresponding light will keep on lighting.

2.2. At this time the

CALORIES

window will display the exercise level(

L1~L3

), you

can press

“

＂

to change to the desired level and then press to confirm,

after you enter the program control function, the corresponding light will keep on lighting.

2.3 After the level is selected, the TIME window will begin to flash, at this time you can

press “ or ＂ to change the time, after the desired time is set, press

to start the treadmill or press back to the Program Selection Mode.

** Time pre-set value

：

25(min)

- 13 -

Range of time

：

5~99(min)

2.4 Press and the treadmill will run according to the pre-set value of the

program’s the speed and angle of program’s 12 segments will change circularly according to the

pre-set values. Every segment will last for 1 minute, when the time is reached, the speed and angle

value will change directly. (During exercise, you can press

“

＂

to directly

change the speed)

2.5 During the function setting of

P1~P5

, if press

，

the treadmill will start at once, the

unset are pre-set values, press

“

＂

and then you can change the pre-set speed

value of

PROGRAM

，

but in the next segment, the value will reset to the original value of the

PROGRAM

- 14 -

Refer to the pre-set parameters of

PROGRAM

：

- 15 -

- 16 -

III. Body fat mode

：

1. Under START/READY condition, press , you can see the Body Fat LED light is blinking,

present you are in to Body Fat function.

When you choose this function, program will require you enter following values.

◎

Age

：

Pre-set value is 30

，

range

：

13~80

，

Step is 1. Press

、

to adjust, after choose

correct value, press into next value setting.

◎

Height

：

Pre-set value is 170 cm

，

range

：

130~200 cm

，

Step is 1 cm. Press

、

to adjust,

after choose correct value, press into next value setting.

◎

Sex

：

Pre-set value is 1(male). Press

、

to change 1 (Male),0(Female). After choose

the correct option, press into the next value setting

◎

Weight

：

Pre-set value is 70 kg

，

range

：

30~130 kg

，

Step is 1 kg. Press

、

to adjust.

After choose correct value, press and put both hands straight and hold the grip pulse

sensor about 15seconds, after 15 seconds, Body Fat window will display your Body Fat value, in

the same time, on the computer panel left side the LED light will display figure evaluation.

2. As the male and female has different fat, so the figure evaluate light also different, below

provide a list for reference：

Light

Sex

1.(male) 0.0~4.9 5.0~9.9 10.0~14.9 15.0~19.9 20.0~24.9 25.0~29.9 30.0~34.9 35.0above

0.(female) 0.0~14.9 15.0~19.9 20.0~24.9 25.0~29.9 30.0~34.9 35.0~39.9 40.0~44.9 45.above

- 17 -

V. HRC function： (This function must be attached with heart beat to finish)

2.1. The program aims to exercise heartbeat. When operating, the heartbeat value is equal

to the pre-set value, the angle and speed will keep steady to maintain the heartbeat

value in certain range to achieve the exercising effect.

2.2. When the MANUAL LED is blinking, press “ or ＂ until the

HRC LED you want stops blinking. Press to make sure. At this time, LCD

of HRC will stop blinking and continue to light. The program will order you to put

in value according to operating style below.

2.3. LCD of AGE light flashes, you can press or to adjust age. After

setting, press

to another position.

Age Pre-set：30

Range of age：13~80，Step is 1

2.4. At this time LCD of PULSE light flashes, the mode will request you to put in

heartbeat value. The value will change according to the age and please refer to the

attached table in the rear of this indication. Then select the suitable value in the table.

You can press or to adjust heartbeat value. If you don’t make any

change, press

and mode will start according to pre-set value and turn to next

position.

2.5. TIME window starts flashing, mode will request you to put in time value. You can

press or to set sport time you need. Or press directly to

start move with no count back.

Range of time value：20~99 min

- 18 -

**The chart below will show the relationship between different age and heart rate of this product of

HRC function：

BPM BPM BPM BPM

Age

H Pre-set L

Age

H Pre-set L

Age

H Pre-set L

Age

H Pre-set L

13 197 124 124 31 180 113 113 49 162 103 103 67 145 92 92

14 196 124 124 32 179 113 113 50 162 102 102 68 144 91 91

15 195 123 123 33 178 112 112 51 161 101 101 69 143 91 91

16 194 122 122 34 177 112 112 52 160 101 101 70 143 90 90

17 193 122 122 35 176 111 111 53 159 100 100 71 142 90 89

18 192 121 121 36 175 110 110 54 158 100 100 72 141 90 89

19 191 121 121 37 174 110 110 55 157 99 99 73 140 90 88

20 190 120 120 38 173 109 109 56 156 98 98 74 139 90 88

21 189 119 119 39 172 109 109 57 155 98 98 75 138 90 87

22 188 119 119 40 171 108 108 58 154 97 97 76 137 90 86

23 187 118 118 41 170 107 107 59 153 97 97 77 136 90 86

24 186 118 118 42 169 107 107 60 152 96 96 78 135 90 85

25 185 117 117 43 168 106 106 61 151 95 95 79 134 90 85

26 184 116 116 44 167 106 106 62 150 95 95 80 133 90 84

27 183 116 116 45 166 105 105 63 149 94 94

28 182 115 115 46 165 104 104 64 148 94 94

29 181 115 115 47 164 104 104 65 147 93 93

30 181 114 114 48 163 103 103 66 146 92 92

BodyPerfect JFIRE Owner's manual

Brand: BodyPerfect

Model: JFIRE

Category: Treadmills

Type: Owner's manual

Download PDF

report

BodyPerfect JFIRE Owner's manual

BodyPerfect JFIRE Owner's manual

Other documents