Sony NEX-5A User manual

4-420-526-12(1)

NEX-3/5/5C/C3

NEX-VG10/VG10E

The new functions provided by this firmware update and their respective

operations are described here.

Please refer to the Instruction Manual of your camera/camcorder and LA-EA2

Mount Adaptor, and the Handbook contained on the supplied CD-ROM.

New functions

The following new functions will be provided by this firmware upgrade.

Using an A-mount lens with the LA-EA2 Mount Adaptor (sold separately), you can take

advantage of the phase-detection AF feature to shoot images.

• You may not be able to use the LA-EA2 Mount Adaptor with certain lenses. You may not use

autofocusing with certain lenses attached via the Mount Adaptor. Consult your Sony dealer or local

authorized Sony service facility for advice on compatible lenses.

• When the lens has a focusing mode switch (AF/MF), set the focusing mode with the switch of the lens.

When the lens does not have the switch, set the focusing mode on the menu.

• It may take a long time or may be difficult for the camera to focus, depending on the lens used or the

subject.

NEX-3/5/5C/C3:

• The following functions do not work when the LA-EA2 Mount Adaptor is attached.

– [Smile Shutter]

– [Face Detection]

• The noise of the camera and lens in autofocusing operation may be recorded during movie recording.

Using an SSM lens will reduce the noise caused by autofocusing. Also, you can disable sound recording

by selecting [Menu] t [Setup] t [Movie Audio Rec] t [Off].

• Aperture is set to F3.5 when you record movies with autofocusing. When you are using a lens with an

F3.5 or smaller F-stop, aperture is set to the maximum F-stop of the lens. When you want to set your own

value for aperture to record movies, select [Aperture Priority] in [Shoot Mode], and select manual

focusing before you start recording. The aperture setting selected at the beginning will remain in effect

until you stop recording. You cannot change the aperture setting while recording a movie.

NEX-VG10/VG10E:

• If the camcorder focuses automatically during movie recording, the noise of the camcorder and lens in the

autofocusing operation is recorded. You can reduce the noise by connecting an external microphone with

a 3.5-mm-diameter mini-plug to the microphone jack of the camcorder, and placing the microphone as far

away from the camcorder as possible. If you want to eliminate the noise completely, it is recommended

that you select MENU t [Setup] t [Movie Audio Rec] t [Off].

Compatibility with the LA-EA2 Mount Adaptor

Notes

LA-EA2 Mount Adaptor

Continued r

A-mount lens

• Aperture is set to F3.5 when you record movies with autofocusing. When you are using a lens with an

F3.5 or smaller F-stop, aperture is set to the maximum F-stop of the lens. When you want to set your own

value for aperture to record movies, select [Aperture Priority] or [Manual Exposure] in [Shoot Mode],

and select manual focusing. If you change the aperture while recording a movie, the noise may be heard

or the screen may become brighter while the camcorder is processing the adjustment.

The following functions will be added to the menu by this firmware upgrade.

• The peaking function is provided for NEX-3/5/5C/C3 in the previous firmware

version. Refer to the corresponding Instruction Manual on the operation and setting.

NEX-3/5/5C: Instruction Manual of Ver. 04

NEX-C3: Ver. 01 (Instruction Manual supplied with the camera)

New functions provided in the menu

Menu New items Functions

Camera Autofocus Area Allows you to set a position for phase-

detection AF, when the LA-EA2 Mount

Adaptor is attached.

Setup AF micro adjustment (AF

Micro Adj./amount/Clear)

Allows you to adjust the autofocused

position finely, when the LA-EA2 Mount

Adaptor is attached.

Peaking (Peaking Level/

Peaking Color) (NEX-

VG10/VG10E only)

Enhances the outline of in-focus ranges

with a specific color in manual focus.

Autofocus Area

Allows you to set a position for phase-detection AF, when using an A-mount lens with

the LA-EA2 Mount Adaptor (sold separately). You can only set the position for phase-

detection AF when an A-mount lens with the LA-EA2 Mount Adaptor is attached.

1 [Menu] t [Camera] t [Autofocus Area] t desired mode.

(Wide) The camera determines which of the 15 AF areas is used for

focusing.

(Spot) The camera uses the AF area located in the center area

exclusively.

(Local) Allows you to choose the area for which you want to activate

the focus from among 15 AF areas with the control wheel

(NEX-3/5/5C/C3) or the v/V/b/B buttons (NEX-VG10/

VG10E).

AF Micro Adj./amount/Clear

Allows you to adjust and register an autofocused position for each lens, when using an

A-mount lens with the LA-EA2 Mount Adaptor (sold separately).

1 [Menu] t [Setup] t [AF Micro Adj.] t [On].

2 [Menu] t [Setup] t [amount] t desired value t OK.

• It is recommended that you adjust the position under actual shooting conditions.

• When you attach a lens for which you have already registered a value, the registered value appears on the

screen. [±0] appears for lens for which a value has yet to be registered.

• If [–] appears, more than 30 lenses have been registered. If you want to register another lens, you must

first clear a value. Attach a lens of the value to be cleared and select [±0]. If you want to clear all

registered values, select [Clear].

• Use [AF Micro Adj.] with Sony, Minolta, and Konika-Minolta lenses only. If you use [AF Micro Adj.]

with other brands of lenses, the registered value may be affected.

• You cannot set [AF Micro Adj.] individually for a Sony, Minolta, and Konika-Minolta lens of the same

specification.

AF Micro Adj. Sets whether or not to use the [AF Micro Adj.] function. Select [On] to

use it. (The default setting is [Off].)

amount Allows you to select an optimum value between –20 and +20.

Selecting a larger value shifts the autofocused position away from the

camera. Selecting a smaller value shifts the autofocused position

closer to the camera.

Clear Clears the value you set.

Notes

Peaking Level (NEX-VG10/VG10E

only)

Enhances the outline of in-focus ranges with a specific color in manual focus. This

function allows you to confirm the focus easily.

1 MENU t [Setup] t [Peaking Level] t desired setting.

• Since the camcorder judges that sharp areas are in focus, the peaking level is different, depending on the

subject, shooting situation, or on the lens used.

• The outline of in-focus ranges is not enhanced when the camcorder is connected using an HDMI cable.

High Sets the peaking level to high.

Mid Sets the peaking level to middle.

Low Sets the peaking level to low.

Off Does not use the peaking function.

Notes

Peaking Color (NEX-VG10/VG10E

only)

Sets the color used for the peaking function in manual focus.

1 MENU t [Setup] t [Peaking Color] t desired setting.

• This item cannot be set when [Peaking Level] is set to [Off].

White Enhances outlines in white.

Red Enhances outlines in red.

Yellow Enhances outlines in yellow.

Note

Sony NEX-5A User manual

Related papers

Other documents