DN1125, DN1126, DN1129
1/3” H.264/MPEG4/MJPEG
550TVL Day/Night IP Camera
Installation and Operations Manual
Model Numbers: DN1125A4, DN1125B4
DN1126A4, DN1126B4
DN1129A4, DN1129B4
Description: H.264/MPEG4/MJPEG IP Box Camera
Dual Configurable Video Streams
with duplex Audio, Data, Alarms, POE
QUICK GUIDE FOR UPDATING Series DN1125, DN1126, DN1129 IP CAMERAS
1. Factory default settings are set as follows:
• IP address: 192.168.
xx.yy (refer to 2.3 Serial Number / MAC Address)
• Mask: 255.255.0.0
• Gateway: 192.168.0.1
• User ID: root
• Password: pass
xx yy xx yy
MAC address = 00-13-23-01-23-45 → IP address = 192.168.35.69
To Convert Hexadecimal numbers to Decimal numbers, use PC calculator.
In Calculator Menu:
1. Click View and select Scientific version
2. Next select Hex to convert digits
xx - use keypad input number ex: 23
3. Next select Dec and get result = 35
4. Repeat for digits yy – select Hex, input number ex: 45
5. Next select Dec and get result = 69
2. To change default IP settings to IP address compatible with your Network:
1. Go to Control Panel of you PC and click on Network and Internet Connections
2. Next click on Network Connections
3. Next right click on Local Area Connection and select Properties
4. Next Scroll down to Internet Protocol TCP/IP, select and click on Properties
5. Next Select “Use the following IP Address and if the default address is:
192.168.35.65 input into the box:
IP address 192.168.35.100 (last numbers higher than default)
Subnet Mask 255.255.0.0
Default Gateway 192.168.1.1
6. Next Click OK and wait 2 minutes for your PC to take on new IP address
7. Next go to Start and click on Run and type cmd
8. Next user must ping device to see that it reponds
9. In cmd prompt enter ping 192.168.35.69 (default IP address of DN1125)
If not detected in Network a screen apperas as (Request timed out:
10.
Convert the Hexadecimal number to Decimal
number
10. If detected in Network a screen appears as Reply from IP address – using example with
192.168.1.65
11. Return to Control Panel and follow procedures 1, 2, 3 and 4
12. Next Select “Obtain an IP address automatically
13. Next Click OK and wait 2 minutes for your PC to take on new IP address
14. Use may open Internet explorer and type
http://192.168.1.65/
15. Screen appears to indicate that the security of your PC is at risk
16. Select Continue to this website; open web browser of DN1125 Encoder
17. Click on Setup user name: root password: pass
18. If image vertical is jumping, select Video, Audio select Video-In
19. In Video-In select NTSC or PAL and click on Apply, wait 3 minutes
20. Next go to System Options to change the IP Address of Encoder
21. Select TCP/IP and input new IP address, click Apply, wait 3 minutes
22. Next ping device as in procedure # 9, if successful then
23. Use may open Internet explorer and type in new IP address selected
24. Screen appears to indicate that the security of your PC is at risk; Select Continue to this
website; open web browser of DN1120 Series IP Cameras
Dante Security
02A.00 4
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
!
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
27
26
26
26
25
24
23
23
22
21
21
20
20
20
18
18
18
18
17
15
15
12
12
12
9
9
9
8
7
Dante Security
02A.00 4
Table of Contents
FEATURES .................................................................................................................
PACKAGE CONTENTS ................................................................................................
PART NAMES ............................................................................................................
Rear View .................................................................................................................................
Bottom View ..............................................................................................................................
INSTALLATION ........................................................................................................
Installing a C/CS Mounting lens ..............................................................................................
Installing an Auto IRIS lens ......................................................................................................
CONNECTIONS ........................................................................................................
9 pin terminal block.................................................................................................................
Power Adaptor Connector (DC 12V) .......................................................................................
CONFIGURATION ....................................................................................................
Set up network environment ..................................................................................................
View video on web page .........................................................................................................
View video using IPAdmin Tool ...........................................................................................
View video using IP address ................................................................................................
Reset ........................................................................................................................................
Factory Default ........................................................................................................................
APPENDIX (A): SPECIFICATIONS ..............................................................................
Summary .................................................................................................................................
VCA (Video Content Analysis) .................................................................................................
Electrical Characteristics .........................................................................................................
Environment Condition ...........................................................................................................
APPENDIX (B): DIMENSIONS ...................................................................................
APPENDIX (C): ACCESSORIES ...................................................................................
APPENDIX (D): TROUBLE SHOOTING .......................................................................
Checking your Firmware .........................................................................................................
Support ....................................................................................................................................
REVISION HISTORY .................................................................................................
DN1120 Installation GuideDN1120 Series
Dante Security
02A.00 6
FEATURES
Camera
Box type IP Camera
Sony 1/3” Super HAD CCD & High Quality SS-HQ1 Full Kit Chip Set
Sony 1/3" Vertical Double Density Color CCD (Optional)
True Day / Night (ICR) and WDR (Optional)
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
De-interlacing on DSP
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MPEG/MJPEG, 25/30FPS@D1(PAL/NTSC)
Audio compression: G.711(µLaw, aLaw)/PCM
Analog video out for external monitors
Video Motion Detection supported
2-way mono audio supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
RS-485 supported
USB 2.0 supported (External storage, Wireless LAN)
Micro SD memory card supported
PoE supported (Optional)
Built-in Video Content Analysis
OSD supported
SDK (Software Development Kit) provided
VCA (Video Content Analysis)
VCA Presence (Included as basic)
VCA Surveillance (Optional)
Dante Security
DN1120 Series DN1120 Installation Guide
02A.00 7
PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
IPE1100 DC power adaptor
Mount ring 9 Pin terminal block
Rubber cap (for protecting CCD) Hexa wrench driver
Adaptor for mounting the camera DC Jack Adaptor Cable
Quick Installation Guide Screws
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 8
PART NAMES
Rear View
Bottom View
⑥
⑤
③
①
① ②
④
①
⑧
⑦
ETHERNET
Micro SD
RESET
LOOP OUT
RS-485 DO DI AUDIO
-
+ C
1
C
1
Out
In
⑨
Dante Security
DN1120 needs a DC12V for power s
Reset switch is used for restarting DN1120 or resetting DN1120 as Factory Default (FD).
DN1120 Installation GuideDN1120 Series
02A.00 9
○
1
Analog video out
It is an analog video output port.
○
2
Reset Switch (Reset)
○
3
USB connector
Insert a USB storage device or Wi-Fi devices. (Only Ralink RT73 chipsets based wireless devices
are available.)
○
4
9 pin terminal block for D/I, D/O, audio, and serial communication
○
5
Power Adaptor Connector (DC 12V)
upply.
Caution
!
Make sure the polarity is correct. Incorrect connection may cause malfunction
or damage to the IP device.
○
6
Micro SD Card socket
It is a memory card slot for external storage.
○
7
LAN Connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base-T Ethernet.
+
-
Status LED Network LED
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 10
○
8
4 pin connector for Auto IRIS
Only DC-drive type is supported.
○
9
Adaptor for mounting the camera
Mounting points adaptor is provided on the bottom(or the top) of the camera for mounting
the camera on a bracket or tripod.
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 11
INSTALLATION
Installing a C/CS Mounting lens
1. Remove the protective rubber cap from the front of the camera.
2. Install the mount ring for lens and adjust the mount ring to fit C or CS lens.
3. Tighten the setscrews using the hexa wrench in the package.
Installing an Auto IRIS lens
1. Remove the cover of the auto iris lens plug and connect it with the lens cable.
2. Connect the auto iris lens plug to the 4-pin lens terminal on the back of the camera.
Note
i
Use the connection recommended by the manufacturer. For best
performance, read the lens manual carefully. You may need to set the flange
back focus.
Note
i
Only DC-drive type is supported.
CW
SET SCREW
Set Screw
(For IRIS LENS)
CCW
CW
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 12
4 pin connector for IRIS
PIN DC IRIS Lens
1 Damp-
2 Damp+
3 Drive+_
4 Drive-
2 1
4 3
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 13
Caution
!
When connecting the DC power supply, make sure the polarity is correct. Incorrect
connection may cause malfunction or damage to the camera.
DC Jack Adaptor
Cabl
LAN Cable
4 pin connector for iris
Analog Video Out
Power Adaptor
ETHERNET
Micro SD
RESET
LOOP OUT
RS-485 DO
DI
AUDIO
-
+ C
1
C
1
Out
In
Dante Security
DN1120
DN1120 Installation GuideDN1120 Series
02A.00 14
CONNECTIONS
9 pin terminal block
RS-485
The RS-485 serial port consists of TRX+(RX+) and TRX-(RX-) as following the following image.
RS-485 Connection
Sensor (DI) connection
provides 1 channel D/I. It can be connected to either a voltage type sensor or a relay
type sensor as the following figures. It can be selected by software.
Caution
!
Do not exceed the maximum input voltage or relay rate.
ETHERNET
Micro SD
RESET
LOOP OUT
RS-485 DO DI AUDIO
-
+
C
1
C
1
Out
In
TRX+(RX+)
<RS-485 Application>
+ -
TRX-(RX-)
TX+
TX-
PTZ Device
485 Device
Dante Security
DN1120
DN1120
DN1120 Installation GuideDN1120 Series
02A.00 15
Alarm (DO) connection
provides 1 channel D/O. It can be connected to either a relay type as the following
figure.
Caution
!
Do not exceed the maximum relay rating.
Audio connection
has a mono audio input and a mono audio output. As the output power for the audio
is low, amplifier speaker is needed. (Do not use a headphone or earphone directly to the
camera.)
DO
COM
Relay Type
Device
Internal
+5V
DI
COM
DI 1
COM
+
-
Relay Type Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal Internal
+
-
Mic
Ain
Speaker
Aout
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 16
Power Adaptor Connector (DC 12V)
Power adaptor connector connects to DC Jack adapter cable.
Caution
!
Make sure the polarity is correct. Incorrect connection may cause malfunction or
damage to the IP device
Caution
!
Power Adaptor Connector (DC 12V)
RED
+
-
+
-
Dante Security
DN1120 series
DN1120 Installation GuideDN1120 Series
02A.00 17
CONFIGURATION
Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address
from the MAC address of your device. Please make sure the device and your PC are on the same
network segment before running the installation. If the network segment between your PC and
the device is different, change your PC’s settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
View video on web page
View the live video on a web page using your IP device and its IP address. You can use the
IPAdminTool or enter the IP address on the web page.
View video using IPAdmin Tool
IPAdminTool automatically searches all activated and shows the product name,
IP address, MAC address and etc. IPAdminTool is provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 18
To use the IPAdminTool and view the live video on a web page:
1. Start IPAdminTool. Names and info of currently activated ID devices appear as a list.
2. Right-click on the desired device and select Web view.
3. Select Yes on the Security Alert pop up.
4. Click pop-up blocked and install the ActiveX control as below. You need to install the
ActiveX for displaying the images.
5. Wait for a few seconds while the web page loads. The live video is displayed as below.
Dante Security
DN1120 Installation GuideDN1120 Series
02A.00 19
View video using IP address
View the live video on a web page using your IP device and its IP address. To have the correct
IP address ready and use it on a web page:
1. Convert a MAC address to an IP address or check the IP address on the IPAdminTool.
(The MAC address is attached on the bottom of the device.)
2. Open a web browser and enter the IP address of the device.
3. Click Continue to this website (not recommended).
4. Click pop-up blocked and install the ActiveX control as below. You need to install the ActiveX
for displaying the images.
5. Wait for a few seconds while the web page loads. The live video is displayed.
Reset
1. While the device is in use, press and hold the Reset button.
2. Release the Reset button after 3 seconds.
3. Wait for the system to reboot.
Factory Default
1. Disconnect the power supply from the device.
2. Connect the power to the device with the Reset button pressed and held.
3. Release the Reset button after 5 seconds.
4. Wait for the system to reboot.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the Hex
adecimal number to Decimal number.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
Dante DN1125A4 Operating instructions
- Category
- Security cameras
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Swann USB 10/100 SW-U-EU1 User manual
-
Videcon DSIRHRV/S Specification
-
LG LNB5110 User guide
-
-
Panasonic BY-HPE11KTA Operating instructions
-
Riva RC3500 Installation guide
-
-
infobit iTrans DU-TR-22B User manual
-
VigilLink VL-DAUSBPE-D-1 User manual
-
ERNITEC EVA 101 Installation guide
