Samsung SCC-B2337P User manual

ENG

DIGITAL COLOR CAMERA

user manual

SCC-B2337(P)

SCC-B2037P

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service,

please register your product at

www.samsungsecurity.com

ENG FRE

GER SPA

ITA

2 – DIGITAL COLOR CAMERA

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..

This symbol indicates high voltage is present inside. It is dangerous to make any kind of

contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance

has been included with this product.

WARNING

To prevent damage which may result in ﬁ re or electric shock hazard, do not expose this appliance

to rain or moisture.

WARNING

Be sure to use only the standard adapter that is speciﬁ ed in the speciﬁ cation sheet. Using any

other adapter could cause ﬁ re, electrical shock, or damage to the product

Incorrectly connecting the power supply or replacing battery may cause explosion, ﬁ re, electric

shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause

abnormal heat generation or ﬁ re.

Securely plug the power cord into the power receptacle. Insecure connection may cause ﬁ re.

When installing the camera, fasten it securely and ﬁ rmly. A falling camera may cause personal

injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers ﬁ lled

with water on top of the camera. Doing so may cause personal injury due to ﬁ re, electric shock,

or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁ re or electric

shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case,

immediately disconnect the power source and contact the service center. Continued use in such

a condition may cause ﬁ re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble

or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized

modiﬁ cations or attempted repair.)

•

1.

2.

3.

4.

5.

6.

7.

8.

9.

W

e

CAUT

D

s

D

1

I

f

o

R

c

K

In

A

d

A

v

T

10.

1.

2.

3.

4.

5.

6.

7.

8.

9.

English – 3

ENG

d of

nce

y

c

ed

k,

uch

e

zed

Safety information

When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁ re or

electric shock.

CAUTION

Do not drop objects on the product or apply strong shock to it. Keep away from a location

subject to excessive vibrationor magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -

10°C), or high humidity. Doing so may cause ﬁ re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move

or reinstall it.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may

cause ﬁ re or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁ re.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may

damage the CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as

vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

10.

1.

2.

3.

4.

5.

6.

7.

8.

9.

4 – DIGITAL COLOR CAMERA

Important Safety Instructions

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including

ampliﬁ ers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

blade or the third prong is provided for your safety. If the provided plug does not ﬁ t into your outlet, consult

an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁ ed by the manufacturer.

Use only with cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or

sold with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been

damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

English – 5

ENG

Contents

Introduction

Features 6

PRODUCT & ACCESSORIES 7

Part Names and Functions 8

Installation

Connecting the Auto Iris Lens Connector 11

Mounting the lens 11

Connecting cables and checking operation 12

How to use OSD Menu

Using Icons in the Menu 13

Main Menu 13

Proﬁ le 14

Camera Setup 16

Intelligence 22

Privacy Zone Setup

24

Other Set 25

Communication 26

System Information 26

Language 26

Speciﬁ cations

Speciﬁ cations 28

es

wide

sult

have

y, or

6 – DIGITAL COLOR CAMERA

Introduction

FEATURES

High Resolution

This camera has realized high resolution of 600 lines using the top-notch full digital image processing and

special algorithm technologies.

Intelligent Motion Detection & Tracking

This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it

sounds an alert if an object passes / enters /exits the virtual fence or virtual area.

XDR (eXtended Dynamic Range)

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a

certain pixel unit to determine the optimal visibility.

DAY/NIGHT

This function can make the IR Cut ﬁ ltering function inactive under the illumination below the normal value.

High Sensitivity

It implements images of high sensitivity using the up-to-date SONY 1/3”Exview-HAD IT CCD..

Low Illumination

It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera

identify objects even in the worst environment.

Superior Backlight Adjustment

When an object has a bright illumination or sunlight behind it, this camera automatically improves the

shaded object picture quality.

Digital Power Synchronization

The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the

operationability and reliability of this camera.

Output Signal Setting

You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy,

Horizontal/Vertical proﬁ ling, and digital zooming.

OSD(On Screen Display) Menu

OSD menu is provided to display the status of camera and to conﬁ gure the functions interactively.

Coaxial Cable Communication

This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the

control signal. In installation or repair, this helps you control the communication controller (optional) without

additional cabling.

❖

•

❖

•

❖

•

❖

•

❖

•

❖

•

❖

•

❖

•

❖

•

❖

•

❖

•

PRO

P❖

•

Came

•

English – 7

ENG

Introduction

and

t

e.

ra

t

PRODUCT & ACCESSORIES

Product & Accessories❖

Accessories

•

Camera

Camera Holder(Mount)

Auto Iris

Lens Connector

User’s Manual

Main Product

•

C Mount Adapter

8 – DIGITAL COLOR CAMERA

Introduction

PART NAMES AND FUNCTIONS

Side View❖

Auto Iris Lens Connector

This groove is used for screwing the mount adapter, a part of the bracket where the camera will be installed.

Auto Iris Lens Control Cable

This cable transmits the power and signals from the camera for controlling the Auto Iris Lens.

Mount Adapter Fixing Grooves

These grooves are used when ﬁ xing screws of the mount adapter connected to the bracket when installing

the camera on it.

•

Note :

When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure ethanol.



–

Mount Adapter

Fixing Grooves

Camera Lens

Auto Iris Lens

Connector

Auto Iris Lens

Control Cable

R❖

English – 9

ENG

Introduction

alled.

ing

Rear Panel❖

n

o

r

q

p

s

n

o

q

s

<AC220V~240V(SCC-B2037P)>

p

10 – DIGITAL COLOR CAMERA

Introduction

n Input/Output Connector

This connector has input and output ports for RS-485 control signals, DAY/NIGHT switching, and alarm

output signals.

No. Function Description

1 ALARM OUT

Alarm out port for motion detection. (Open collector type)

2 GND Grounding Port.

3 GND Grounding Port.

4 SHUTTER (S0)

This is a port for selecting an external high speed shutter mode.

If connected in LOW (0V), it will become ON inside.

5 SHUTTER (S1)

This is a port for selecting an external high speed shutter mode.

If connected in LOW (0V), it will become ON inside.

6 SHUTTER (S2)

This is a port for selecting an external high speed shutter mode.

If connected in LOW (0V), it will become ON inside.

7 5V OUT

Power supply port for RS-485 JIG. Use within typical DC +5V 100mA

8

DAY/NIGHT IN

This is a port for DAY&NIGHT conversion.

High(DC +3V~+5V) : DAY(COLOR) Mode,

Low(0V) : NIGHT(BW) Mode

9 RS-485 DATA-

This is a port for connection to RS-485 DATA- signal line.

10 RS-485 DATA+

This is a port for connection to RS-485 DATA+ signal line.

o SETUP Switch

This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the

MAIN MENU appears.

ef

(Left/Right)

: By pressing this switch left or right, you can move left or right on the menu or change the

displayed value.

cd

(Up/Down) :

By pressing this switch up or down, you can move up or down on the menu.

 : When you press this switch in the menu, the selected function is conﬁ rmed. To enter a submenu, press

this button.

p Power Display LED

When the power is normally connected, the red LED lights.

q Video OUT Port

This is connected to the Video Input Port of the monitor and it outputs the Video signals.

r GND

This is a grounding port.

s Power Connection Port

This is connected to the Power cable.

CO

Conn

the A

P

N

1

2

3

4

No



–

English – 11

ENG

he

e the

ress

Installation

CONNECTING THE AUTO IRIS LENS

CONNECTOR

Connect each uncovered shutter control cables to

the Auto Iris Lens Connector as the following

No.

DC Control

Type

Video Control Type

1 Damp(-) Power (+12V)

2 Damp(+) Not applicable

3 Drive(+) Video Signal

4 Drive(-) Ground

Note :

You can switch a control type of the lens in the menu.



–

MOUNTING THE LENS

When using the CS lens

Mount the CS lens by rotating it clockwise as shown

in the picture:

When using the C lens

After mounting the C-mount adapter by rotating it

clockwise, turn the C lens clockwise until it is ﬁ xed as

shown in the picture.

CS lens

C lens

12 – DIGITAL COLOR CAMERA

Installation

CONNECTING CABLES AND

CHECKING OPERATION

①

Connect one end of the BNC cable to the

VIDEO OUT Port on the rear of the camera.

② Connect another end of the BNC cable to the

VIDEO IN Port on the monitor.

③

Finally connect the power adapter to the

camera. You can connect 2 lines of the power

adapter to the camera using the Slot Head

screwdriver as shown in the picture.

(GND: cable with the white stripe line)

1 2

3 4

5 6

7

8

1

.

A

L

A

R

A

M

O

U

T

2

.

G

N

D

3

.

G

N

D

4

.

S

H

U

T

E

R

(

S

O

)

5

.

S

H

U

T

E

R

(S

1

)

6

.

S

H

U

T

E

R

(S

2

)

7

.

5

V

O

U

T

8

.

D

A

Y

/

N

I

G

H

T

I

N

Note :

Connect any power source of AC 24V and DC 12V

irrespective of polarity.



–

1

2

3

4

5

6

7

8

1

.

A

L

A

R

A

M

O

U

T

2

.

G

N

D

3

.

G

N

D

4

.

S

H

U

T

E

R

(

S

O

)

5

.

S

H

U

T

E

R

(

S

1

)

6

.

S

H

U

T

E

R

(

S

2

)

7

.

5

V

O

U

T

8

.

D

A

Y

/

N

I

G

H

T

I

N

Video In Terminal of Monitor Rear

Surface

BNC cable

Video Out Terminal

USI



E

B

sa



R



R



U

P

O

e



U

P

O

re

•

English – 13

ENG

wer

USING ICONS IN THE MENU

 (EXIT)

Exits the menu setting.

Before you exits the menu setting, select SAVE to

save your settings, or select QUIT to cancel.

 (RET)

Returns to the previous menu.

 (HOME)

Returns to the main menu.

 (SAVE)

Used to save your settings of MASK AREA,

PRIVACY ZONE and more.

Once you save your settings, they will remain

even if you select QUIT in the menu.

 (DEL)

Used to deletes your settings of MASK AREA,

PRIVACY ZONE and more.

Once you delete your settings, they will not be

restored even if you select QUIT in the menu.

•

MAIN MENU

ÃÃMAIN MENUÃÃ

PROFILE



CAMERA SET

INTELLIGENCE

PRIVACY ZONE

OTHER SET

COMMUNICATION

SYSTEM INFO

LANGUAGE



PROFILE

You can set a mode according to the camera

installation conditions.

CAMERA SET

Conﬁ gure Camera related functions and data.

INTELLIGENCE

You can conﬁ gure the settings of motion

detection, tracking and more.

PRIVACY ZONE

You can conﬁ gure the privacy related settings.

OTHER SET

You can conﬁ gure for Factory Defaults, and more.

COMMUNICATION

Conﬁ gures the settings regarding the RS-485

communication.

SYSTEM INFO.

Displays the system information including the

camera version and communication settings.

LANGUAGE

Select a preferred one from the supported

languages.

•

How to use OSD Menu

14 – DIGITAL COLOR CAMERA

How to use OSD Menu

PROFILE

e

PROFILE

f

Ã

STANDARD

ITS

BACKLIGHT

DAY/NIGHT

GAMING

CUSTOM

 

In the PROFILE menu, you can conﬁ gure the following camera settings at once.

CAMERA SET Menu

STANDARD ITS BACKLIGHT DAY/NIGHT GAMING

Sub-menus

IRIS ALC ALC ALC ALC ALC

ALC -- ---

LENS DC DC DC DC DC

LEVEL 0 0 0 0 0

BACKLIGHT OFF OFF BLC OFF OFF

MOTION (F.FAST)--- (F.FAST)--- NORM (F.FAST)--- SLOW

DNR MID MID MID MID MID

SHUTTER OFF AUTO1/250 OFF OFF OFF

SENS-UP AUTOx4 AUTOx2 AUTOx4 AUTOx4 AUTOx4

XDR MID MID MID MID MID

DAY/

NIGHT

AUTO AUTO DAY AUTO DAY

NIGHT - - - - -

BURST OFF ON OFF OFF OFF

EXT -- ---

BURST OFF ON OFF OFF OFF

Pr

M

W

D

IT

It w

B

It w

D

It w

G

It w

❖

English – 15

ENG

How to use OSD Menu

CAMERA SET Menu

STANDARD ITS BACKLIGHT DAY/NIGHT GAMING

Sub-menus

WHITE

BAL

DAY DAY/NIGHT DAY DAY/NIGHT DAY

DAY -- ---

MODE ATW2 ATW1 ATW1 ATW1 ATW1

RED00 000

BLUE 0 0 0 0 0

NIGHT - - - - -

BRIGHTNESS

User setting

allowed

MID

User setting

allowed

MID

User setting

allowed

MODE OFF ATW2 OFF ATW2 OFF

RED

User setting

allowed

0

User setting

allowed

0

User setting

allowed

BLUE

User setting

allowed

0

User setting

allowed

0

User setting

allowed

DETAIL 2 2 2 2 2

ITS

It will be set automatically so you can easily check the trafﬁ c conditions.

BACKLIGHT

It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.

DAY/NIGHT

It will be set automatically so it optimizes to the day or night conditions, respectively.

GAMING

It will be set automatically to help you take a picture in a regular indoor lighting condition.

❖

16 – DIGITAL COLOR CAMERA

How to use OSD Menu

CAMERA SETUP

eCAMERA SETf

CAMERA ID OFF

IRIS ALC

MOTION (F.FAST)---

DNR MID

SHUTTER OFF

SENS-UP AUTO X4

FLICKERLESS (OFF)---

XDR MID

 

d

c

DAY/NIGHT AUTO

WHITE BAL 

DIGITAL ZOOM

OFF

DETAIL [2]

V-SYNC INT

AGC COLOR SUP

LOW

REVERSE OFF

POSI/NEGA +

PIP OFF

 

d

c

DIS OFF

 

Setup the general functions of zoom camera module.

Use the

cdef

switch to select a menu item.

CAMERA ID [OFF, ON]

CAMERA ID

ABCDEFGHIJKLMNOPQRSTUVWXYZ0

123456789 :?-+*()/

SP

ffee

SP LOCATION

CAMERA-1..................

...........................

  

The CAMERA ID menu is used for you to assign

a unique name to a camera. If you press the

SETUP switch with the CAMERA ID menu

selected, you will see the appropriate screen.

You can enter up to 54 alphanumeric or

special characters for the CAMERA ID. Select

LOCATION and press the SETUP switch to

move the display position of the CAMERA ID.

IRIS [ALC, ELC]

The IRIS menu is used if you want to adjust the

intensity of radiation incoming to the camera.

ALC (Automatic Light Control)

① If you press the SETUP switch with an ALC-

based sub menu selected, you will see the

appropriate screen.

ALC

LENS DC

LEVEL [00]----I----

BACKLIGHT OFF

  

The LENS menu is used if you select a type of

the AI lens.

For normal operation, you must select DC for a

DC-type lens, and select VIDEO for a VIDEO-

type lens.

❖

•

②

EL

①

•

English – 17

ENG

How to use OSD Menu

sign

ct

D.

he

LC-

e

e of

or a

O-

The LEVEL menu is used to adjust the

overall brightness, where “+” will increase the

brightness and “–” will decrease it.

② If you set the BACKLIGHT option to BLC,

you will see a menu where you can set the

BLC area.

you can set the desired BLC zone by deﬁ ning

the size and location.

ALC

LENS DC

LEVEL [00]----I----

BACKLIGHT BLC

AREA USER

<SIZE>

<LOCATION>

  

If you use an ordinary camera in a scene

with an intensive backlight, the object will be

displayed dark on the monitor affected by the

backlight. To solve this problem, you can use

the BLC(Back Light Compensation) function

to improve the sharpness of the image in

such a high contrast scene.

ELC (Electronic Light Control)

①

If you press the SETUP switch when the ELC



submenu is selected, the corresponding screen

appears. You can make the ELC (Electronic Light

Control) function active or not.

ELC

LEVEL [00]----I----

BACKLIGHT OFF

  

•

② In similar to ALC setting, you can specify the

BLC area.

ELC

LEVEL [00]----I----

BACKLIGHT BLC

AREA USER

<SIZE>

<LOCATION>

  

AGC

[OFF, VERY LOW, LOW, MID, HIGH, VERY

HIGH, USER, FIX]

The AGC (Auto Gain Control) menu is used to

set the AGC level of the camera. When the AGC

is active, the camera automatically increases the

sensitivity by amplifying the Video signal when

the strength of the signal falls below the normal

value.

If OFF or FIX mode is selected in the SENS-UP

menu, you can specify the AGC level.

If you press the SETUP switch with a USER

sub menu selected, you will see the appropriate

screen.

AGC USER

LEVEL [16]

  

In USER mode, you can break down the level in

16 steps from VERY LOW to VERY HIGH to your

preference.

❖

18 – DIGITAL COLOR CAMERA

How to use OSD Menu

AGC FIX

LEVEL [01]

  

If you press the SETUP switch with a FIX sub

menu selected, you will see the appropriate screen.

As a ﬁ xed value of the AGC gain is used in FIX

mode, you can select one of the 16 detailed levels

from VERY LOW to VERY HIGH before ﬁ xing it.

Note :

If the DAY/NIGHT menu of the CAMERA SET is set to

AUTO, the AGC menu will be deactivated.

If FLICKERLESS is set to ON, the AGC FIX mode will be

disabled.

MOTION

[S.SLOW, SLOW, NORM, FAST, F.FAST]

The MOTION menu is used to adjust the strength

of the AGC level for a control of the camera motion.

This is available only if the SENS-UP menu is set

to AUTO.

You can select one from S.SLOW, SLOW, NORM,

FAST and F.FAST for the AGC level.

If you monitor a fast moving object in a low contrast

scene, select F.FAST while select S.SLOW for a

hardly moving object in the same lighting condition.

Note :

If the DAY/NIGHT menu of the CAMERA SET is set to

AUTO, the MOTION menu will be deactivated.

DNR

[OFF,LOW,MID,HIGH, USER(1~16)]

You can conﬁ gure the DNR (Digital Noise

Reduction) related settings.

Reduces the noise on the screen.

This is especially useful for a severely distorted screen.

You can set the level if you set DNR to USER.



–

❖



–

❖

SHUTTER

[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250,

AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO

1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250,

1/500, 1/1000, 1/2000, 1/4000, 1/10K , EXT]

The SHUTTER menu is used to set the ﬁ xed

high-speed electronic shutter, auto high speed

electronic shutter and external high speed

electronic shutter(EXT).

You can select one of 7 options from 1/100(PAL:1/120)

to 1/10K for the ﬁ xed high speed electronic shutter,

which is mostly used for imaging a fast moving object.

The auto high speed electronic shutter operates

as the ﬁ xed high speed shutter in a high contrast

scene but automatically focuses the target if the

iris opens fully in a low contrast scene like in ELC

mode. When it gets brighter back, the mode will

switch to the ﬁ xed high speed electronic shutter

mode.

However, the auto high speed shutter operates

properly only in a camera featuring a DC or VIDEO

lens.

In external high speed electronic shutter (EXT)

mode, you can select one of 8 modes from OFF

through 1/100(PAL:1/120) to 1/10K for the high

speed electronic shutter. It works as the high

speed electronic shutter. You can select an

option using SHUTTER(S0), SHUTTER(S1) and

SHUTTER(S2) on the rear.

Connect each of the terminals to GND.

See the below table for the operation.

SHUTTER(S0) SHUTTER(S1) SHUTTER(S2)

OFF

(NTSC: 1/60,

PAL:1/50)

OFF OFF OFF

1/100

(PAL:1/120)

ON OFF OFF

1/250 OFF ON OFF

1/500 ON ON OFF

1/1000 OFF OFF ON

❖

No

S

[O

X

F

A

d

e

b

m

No



–

❖



–

English – 19

ENG

How to use OSD Menu

UTO

0,

d

/120)

r,

ect.

es

ast

e

LC

will

er

s

DEO

FF

h

d

R(S2)

F

1/2000 ON OFF ON

1/4000 OFF ON ON

1/10K ON ON ON

Note :

If IRIS mode is set to ELC, the SHUTTER menu will be

deactivated as you adjust the brightness using the

electronic shutter.

If the SENS-UP function is set to AUTO, only items of

OFF and AUTO are available in the SHUTTER menu.

If the SENS-UP mode is set to FIX, the SHUTTER menu

will be deactivated.

If the FLICKERLESS function is set to ON, the SHUTTER menu

will be deactivated.

SENS-UP

[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO

X8, AUTO X12, AUTO X16, AUTO X24, AUTO

X32, AUTO X48, AUTO X64, AUTO X96, AUTO

X128, AUTO X256, AUTO X512, FIX X2, FIX

X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24,

FIX X32, FIX X48, FIX X64, FIX X96, FIX X128,

FIX X256, FIX X512]

Automatically detects the ambient level of

darkness in the dark or low contrast scene to

extend the accumulated time, keeping the image

bright and sharp; It can be also used as FIX

mode.

Note :

If the SHUTTER option is set to ﬁ xed electronic shutter or

EXT mode, the SENS-UP menu will be deactivated.

If FLICKERLESS is set to ON, the FIX mode of the SENS-

UP menu will be disabled.

If the IRIS menu is set to ELC, the electronic shutter will

control the brightness so the SENS-UP function can not

be set to FIX mode, but to OFF or AUTO mode.

If the SHUTTER menu is set to AUTO, the SENS-UP

menu can be set to either OFF or AUTO mode.



–

❖



–

FLICKERLESS [OFF, ON]

If set to ON, the shutter speed will be ﬁ xed to

1/100(PAL:1/120) second. This will prevent possible screen

distortion due to a mismatch between the vertical sync

frequency and the blinking frequency of the lighting.

Note :

If the IRIS function is set to ELC, the Flickerless menu will

be deactivated. If the SHUTTER menu is set to AUTO, FIX

or EXT mode, the Flickerless menu will be deactivated.

If the SENS-UP function is set to FIX mode, the Flickerless

menu will be deactivated.

If AGC is set to FIX mode, the FLICKERLESS function will

be disabled.

XDR (eXtended Dynamic Range)

[OFF, LOW, MID, HIGH]

Actively controls the gamma compensation in the

way it operates the ambient luminance contrast

in a certain pixel unit to determine the optimal

visibility.

Select one from OFF, LOW, MID and HIGH.

Closing to HIGH will increase the compensation

level.

DAY/NIGHT

[DAY,NIGHT,AUTO,EXT]

DAY

If set to DAY, it will be ﬁ xed to DAY mode

regardless of the ambient conditions.

NIGHT

If set to NIGHT, it will be ﬁ xed to Black-and-White

mode regardless of the ambient conditions.

If you press the SETUP switch with a NIGHT sub

menu selected, you will see a menu where you can

set Burst to OFF/ON.

If BURST is set to ON, the Burst signal will output

together with the black-and-white composite video

signal. If BURST is set to OFF, the Burst signal does

not output.

You can set the BURST option to OFF/ON, or

select to output the Burst signal in NIGHT mode.

❖



–

❖

•

20 – DIGITAL COLOR CAMERA

How to use OSD Menu

AUTO

The camera will automatically switch between

DAY and NIGHT mode, according to the lighting

condition.

If you press the SETUP switch with an AUTO-

based sub menu selected, you will see the

appropriate screen.

AUTO

BURST OFF

DAYÆNIGHT

BRIGHTNESS MID

DWELL TIME 2S

NIGHTÆDAY

BRIGHTNESS MID

DWELL TIME 5S

MASK AREA 1 2

  

You can set the BURST option to OFF/ON, or

select to output the Burst signal in NIGHT mode.

You can select from LOW, MID and HIGH for

the brightness of DAYÆNIGHT, which is a

brightness level in switching from the color ﬁ lter

to Black-and-White. Closing to LOW from HIGH

will switch the ﬁ lter in a low contrast scene.

The DWELL TIME of DAYÆNIGHT is a time

required to determine the need for switching the

ﬁ l t e r .

You can select from LOW, MID and HIGH for

the brightness of NIGHTÆDAY, which is a

brightness level in switching from the Black-and-

White ﬁ lter to color. Closing to LOW from HIGH

will switch the ﬁ lter in a low contrast scene.

The DWELL TIME of NIGHTÆDAY is a time

required to determine the need for switching the

ﬁ l t e r .

The MASK menu is used to prevent a ﬁ lter

switch error or inability of determining the switch

in existence of a high spot light source at night.

If you press the SETUP switch in item 1 or 2 of

the MASK menu, you will see a menu where you

can specify an area to mask.

•



MASK AREA



<SIZE>



<LOCATION>

    

You can specify Mask 1 and 2 simultaneously.

The mask is used only for determining the ﬁ lter

switch and any excessive bright area at night will

be masked.

Note :

If BACKLIGHT is set to BLC, the MASK AREA function will

be deactivated.

EXT

This enables an auto switch between DAY and

NIGHT mode using the interface with the external

sensor.

WHITE BAL [DAY/NIGHT]

If you want to adjust the color scheme, use the

WHITE BALANCE function.

DAY

In DAY mode, you can set the color values of

RED and BLUE. The screen will be displayed in

colors according to your settings.

WHITE BAL

DAY/NIGHT DAY

MODE AWC

RED [00]----I----

BLUE [00]----I----

R-GAIN [0248]

B-GAIN [0247]

  

Note :

You can set the values of R-GAIN and B-GAIN only in

AWC mode.



–

•

❖

•



–

NI

U

b

lu

If

b

if

D

In

B

d

No

Fo

5

•



–

•

Page is loading ...

Samsung SCC-B2337P User manual

Samsung SCC-B2337P User manual

in other languages

Related papers

Other documents