Godox VING TTL Li-ion Camera Flash for Fuji V860IIF User manual

Brand: Godox

Model: VING TTL Li-ion Camera Flash for Fuji V860IIF

Category: Camera flashes

Type: User manual

This manual is also suitable for

V860II-F 2.4G TTL Flash for Fuji Camera GN60 HSS 1/8000s 1.5S Recycle Time 650 Full Power Pops 22 Steps of Power Output Round Flash Head S-R1 Magnetic Modifier Adapter

INSTRUCTION MANUAL

说明手册

中英文双语 / Chinese English Bilingual

在使用本产品之前：

请先仔细阅读本手册，以确保您能安全使用。请保存好本手册以备将

来查询参考。

Before using this product:

Please read this user manual carefully in order to ensure your safety

and the proper operation of this product. Keep for future reference.

锂电机顶闪光灯

TTL

Pioneering Camera FlashTTL Li-ion

For Fuji

705-V862F0-00 Made in China

地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋1层至4层、4栋1层至4层

1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan Industrial Zone, Tangwei

Community, Fuhai Street, Bao’an District, Shenzhen 518103, China

电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423

邮箱/E-mail: [email protected] http://www.godox.com

深圳市神牛摄影器材有限公司

GODOX Photo Equipment Co., Ltd.

- 25 - - 26 -

Thank you for purchasing this product.

This V860IIF camera flash applies to Fuji series cameras and is

compatible with TTL autoflash. With this TTL compatible flash, your

shooting will become simpler. You can easily achieve a correct flash

exposure even in complex light-changing environments. This

camera flash features:

● GN60 (m ISO 100, @200mm). 22 steps from 1/1 to 1/128.

● Fully support Fuji series TTL camera flash. Workable as Master or

Slave unit in a wireless flash group.

● Use dot-matrix LCD panel to make clear and convenient

operations.

● With built-in 2.4GHz wireless remote system to support

transmitting and receiving.

● Provided multiple functions, include HSS (up to 1/8000s), second-

curtain sync, FEC, etc.

● Use optional FT-16S to adjust flash parameters & trigger the flash.

● Stable consistency and color temperature with good even lighting.

● Support with firmware upgrade.

Foreword

Compatible Camera Models

• This table only lists the tested camera models, not all Fuji cameras. For the

compatibility of other camera models, a self-test is recommended.

• Rights to modify this table are retained.

X-Pro2, X-T20 , X-T2 , X-T1

X-Pro1 , X-T10 , X-E1 , X-A3

X100F, X100T

Fuji cameras are divided into three kinds according to their

different controlling ways to camera flash:

Compatible camera models & functions support

Camera Flash

TTL Flash M Manual Flash

Multi

Strobo

-scopic

Flash

Stan-

dard

REAR

HSS(FP)

REAR

HSS(FP)

√ √ √ √ √ √ √

2.4G Wireless Control

√ √ √

√ √ √ √ √ √ √

√ √ √

√ √ -- √ √ -- √

-- -- -- -- -- -- -- --

AF-assist Beam

√

camera

Stan-

dard

TTL Flash M Manual Flash

Multi

Strobo

-scopic

Flash

Stan-

dard

REAR

HSS(FP)

REAR

HSS(FP)

Stan-

dard

1. X100T do not have second curtain sync (REAR) function.

2. The AF assist beam will light up when the shutter is at low speed (＜200).

Always keep this product dry. Do not use in rain or in damp

conditions.

Do not disassemble. Should repairs become necessary, this

product must be sent to an authorized maintenance center.

Keep out of reach of children.

Stop using this product if it breaks open due to extrusion, falling

or strong hit. Otherwise, electric shock may occur if you touch

the electronic parts inside it.

Do not fire the flash directly into the eyes (especially those of

babies) within short distances. Otherwise visual impairment

may occur.

Do not use the flash unit in the presence of flammable gases,

chemicals and other similar materials. In certain circumstance,

these materials may be sensitive to the strong light emitting

from this flash unit and fire or electromagnetic interference may

result.

Do not leave or store the flash unit if the ambient temperature

reads over 50℃. Otherwise the electronic parts may be

damaged.

Turn off the flash unit immediately in the event of malfunction.

warning

Pioneering Li-ion Camera Flash

- 27 - - 28 -

Foreword

Compatible Camera Models

Warning

Name of Parts

Body

Control Panel

LCD Panel

What's in the Box of V860IIF Kit?

What's in the Box of V860IIF (only flash unit)?

Separately Sold Accessories

Battery

Attaching to a Camera

Power Management

Flash Mode: TTL Autoflash

FEC (Flash Exposure Compensation)

High-Speed Sync

Second-Curtain Sync

Flash Mode – M: Manual Flash

Flash Mode – Multi: Stroboscopic Flash

Wireless Flash Shooting: Radio (2.4G) Transmission

Other Applications

Wireless Control Function

Sync Triggering

Auto Focus Assist Beam

Bounce Flash

Creating a Catchlight

ZOOM: Setting the Flash Coverage and Using the Wide Panel

Low Battery Indicator

C.Fn: Setting Custom Functions

Firmware Upgrade

Protection Function

Technical Data

Troubleshooting

Maintenance

Contents

Conventions used in this Manual

● This manual is based on the assumption that both the camera and

camera flash’s power switches are powered on.

● Reference page numbers are indicated by “p.**”.

● The following alert symbols are used in this manual:

The Caution symbol gives supplemental information.

The Note symbol indicates a warning to prevent shooting

problem.

RST

SET

01. Catchlight Panel

02. Built-in Wide Panel

03. Flash Head

04. Optic Control Sensor

05. Wireless Control Port

06. Sync Cord Jack

08. Dot-marix LCD Panel

09. Lock Ring

10. Battery Compartment

11. USB Port

12. Slave Flash Ready Indicator

● Body

14. <MODE> Mode Selection

Button / Lock button

15. < >Wireless Selection

Button

16. Select Dial

17. <SET> Set Button

18. ON/OFF Power Switch

19. < > Test Button / Flash

Ready Indicator

20. Function Button 1

21. Function Button 2

22. Function Button 3

23. Function Button 4

● Control Panel

- 29 - - 30 -

13. Focus Assist Beam07. Hotshoe

● LCD Panel

(1) TTL Autoflash

Zoom : zoom display (Page 46)

: Automatic

: Manual(Page 37)

TTL : TTL autoflash

Focus length (Page 46)

: High-speed sync

(Page 35)

: Flash exposure

compensation (Page 35)

Distance indicator

display

Flash exposure

compensation amount

(2) M Manual Flash

● The display will only show the settings currently applied.

● The functions displayed above function buttons 1 to 4, such

as and , change according to settings’ status.

● When a button or dial is operated, the LCD panel

illuminated.

M : Manual flash

Manual flash output

(3) Multi Stroboscopic Flash

Multi : Stroboscopic flash

Number of flashes

Flash frequency

SYNC

● Separately Sold Accessories

The product can be used in combination with the following

accessories sold separately, so as to achieve best photography

effects:

X1T-F wireless ﬂash trigger, FT-16S power & trigger control, Mini

softbox, White & Silver reﬂector, Honeycomb, Color gels, Snoot, etc.

Flash mode

: Group ﬂash (radio transmission)Gr

Channel

: Radio transmission

wireless shooting

(4) Radio Transmission Shooting

● Master Unit

● Slave Unit

: Slave

: Slave icon

Firing group

FEC

● What’s in the Box of V860IIF Kit?

1. Flash Unit　2. Li-ion Battery Pack　3. Battery Charger　

4. Battery Charger Cable　5. Mini Stand　

6. Protection Case　7. Instruction Manual

● What’s in the Box of V860IIF (only ﬂash unit)?

1. Flash Unit　5. Mini Stand　6. Protection Case　7. Instruction Manual

● Features

1. This ﬂash unit uses Li-ion polymer battery which has long runtime.

The available charge-and-discharge times are 500.

2. It is reliably safe. The inner circuit is against overcharge,

overdischarge, overcurrent, and short circuit.

3. Take only 2.5 hours to fully charge the battery by using the

standard battery charger.

● Cautions

1. Do not short circuit.

2. Do not expose to rain or immerse into water. This battery is not

water proof.

3. Keep out of reach of children.

4. No over 24 hours’ continuous charging.

5. Store in dry, cool, ventilated places.

6. Do not put aside or into ﬁre.

7. Dead batteries should be disposed according to local regulations.

8. If the battery had ceased using for over 3 months, please make a

full recharge.

● Loading and Unloading the Battery

Battery

To load the battery, push the

1 battery compartment cover

downward and open it.

According to the triangle sign

2 on the battery pack, insert it

into the compartment until a

white knob locks the battery

with a click sound.

- 31 - - 32 -

● Battery Level Indication

Make sure the battery pack is securely loaded in the ﬂash. Check

the battery level indication on the LCD panel to see the remaining

battery level.

Battery Level Indication

3 grids

2 grids

1 grid

Blank grid

Blinking

To unload the battery, tap the

3 white knob and the battery

pack will pop out. Then close

the compartment.

The battery level is going to be used out

immediately. And the ﬂash will auto power off

in 1 minute.

Note: Please recharge the battery as soon as

possible (within 10 days). Then, the battery can be

used or be placed for long period.

Meaning

Full

Middle

Low

Lower battery, please recharge it.

- 33 - - 34 -

Attaching to a Camera

Attach the Camera Flash.

● Slip the camera flash’s

mounting foot into the

camera’s hotshoe all the

way.

Secure the Camera Flash.

● Rotate the lock ring on the

mounting foot until it locks

up.

Detach the Camera Flash.

● Rotate the lock ring on the

mounting foot until it is

loosened.

C.Fn

Power Management

Use ON/OFF Power Switch to power the flash unit on or off. Turn off

if it will not be used for an extended period of time. Setting as a

master flash, it will turn the power off automatically after a certain

period (approx. 90 seconds) of idle use. Pressing the camera

shutter halfway or pressing any flash button will wake up the flash

unit. Setting as a slave flash, it will enter sleep mode after 60

minutes (adjustable, 30 minutes by default) of idle use. Pressing

any flash button will wake it up.

Disabling Auto Power Off function is recommended

when the flash is used off camera. (C.Fn-APO, Page 47)

Slave Auto Power Off Timer is set to 60 minutes by

default. Another option “30 minutes” is available.

(C.Fn-Sv APOT, Page 47)

Flash Mode: TTL Autoflash

This flash has three flash modes: TTL, Manual (M), and Multi

(Stroboscopic). In TTL mode, the camera and the flash will work

together to calculate the correct exposure for the subject and the

background. In this mode, multiple TTL functions are available:

FEC, HSS, second curtain sync, etc.

* Press <MODE> Mode Selection Button and three flash modes will

display on the LCD panel one by one with each pressing.

TTL Mode

Press <MODE> Mode Selection Button to enter TTL mode. The

LCD panel will display <TTL>.

● Press the camera release button halfway to focus. The aperture

and effective flash range will be displayed in the viewfinder.

● When the shutter button is fully pressed, the flash will fire a pre-

flash that the camera will use to calculate exposure and flash

output the instant before the photo is taken.

- 35 - - 36 -

　　 FEC: Flash Exposure Compensation

With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.

It is useful in situations where minor adjusting of the TTL system is

needed based on the environment.

Setting FEC:

Set the flash exposure

2 compensation amount.

● Turn the Select Dial to set

the amount.

● “0.3”means 1/3 step,

“0.7”means 2/3 step.

● To cancel the flash

exposure compensation,

set the amount to “+0”.

Press < SET > button again

3 to confirm the setting.

Press Function Button 2

1 < >. The icon < >

and flash exposure

compensation amount will be

highlighted on the LCD

panel.

High-Speed Sync

High Speed Sync (Hss flash) enables the flash to synchronize with

all camera shutter speeds. This is convenient when you want to use

aperture priority for fill-flash portraits.

● Setting the flash to High-speed Sync mode when it is on the camera:

Use the Flash Setting ＞ Flash Light Function Setting on the

camera’s shooting menu to adjust settings of the flash light. More

details please refer to camera’s instruction menu.

● When choosing FP on the “SYNC” setting, it means the

high-speed sync function is turned on.

SYNC.MODE

TTL

±0

-5.0 +5.0

TTL MODE TTL

ZOOM

M 16mm

LED AF

SYNC.

ANGLE

BACK

ADJUST

END

SHOE MOUNT FLASH

● With high-speed sync, the faster the shutter speed, the

shorter the effective flash range.

● Multi flash mode cannot be set in high-speed sync mode.

● Over-temperature protection may be activated after 15

consecutive high-speed sync flashes.

Second-Curtain Sync

With a slow shutter speed, you can create a light train following the

subject. The flash fires right before the shutter closes.

● Setting second-curtain sync:

Use the Flash Setting ＞Flash Light Function Setting on the

camera’s shooting menu to adjust settings of the flash light. More

details please refer to camera’s instruction menu.

● When choosing REAR on the “SYNC” setting, it means the

second-curtain sync function is turned on.

SYNC.MODE

TTL

±0

-5.0 +5.0

TTL MODE TTL

ZOOM

M 16mm

LED AF

SYNC.

ANGLE

REAR

BACK

ADJUST

END

SHOE MOUNT FLASH

- 37 - - 38 -

Set the flash frequency and

3 flash times.

● Press Function Button 3

< > to select the flash

times. Turn the Select Dial to

set the number.

● Press Function Button 4

< > to select the flash

frequency. Turn the Select

Dial to set the number.

● After you finish the setting,

press <SET> button and all

the settings will be displayed.

Flash Mode -- Multi:Stroboscopic Flash

With stroboscopic flash, a rapid series of flashes is fired. It can be

used to capture a multiple images of a moving subject in a single

photograph.

You can set the firing frequency (number of flashes per sec.

expressed as Hz), the number of flashes, and the flash output.

Press <MODE> button so

1 that < > is displayed.

Turn the Select Dial to choose

2 a desired flash output.

Calculating the Shutter Speed

During stroboscopic flash, the shutter remains open until the firing

stops. Use the formula below to calculate the shutter speed and set

it with the camera.

For example, if the number of flashes is 10 and the firing frequency is

5 Hz, the shutter speed should be at least 2 seconds.

Number of Flashes / Flash Frequency = Shutter Speed

To avoid overheating and deteriorating the flash head, do not

use stroboscopic flash more than 10 times in succession.

After 10 times, allow the camera flash to rest for at least 15

minutes. If you try to use the stroboscopic flash more than 10

times in succession, the firing might stop automatically to

protect the flash head. If this happens, allow at least 15

minutes’ rest for the camera flash.

● Stroboscopic flash is most effective with a highly reflective

subject against a dark background.

● Using a tripod and a remote control is recommended.

● A flash output of 1/1 and 1/2 cannot be set for stroboscopic

flash.

● Stroboscopic flash can be used with“buLb”.

● If the number of flashes is displayed as “--”, the firing will

continue until the shutter closes or the battery is

exhausted. The number of flashes will be limited as shown

by the following table.

MULTI

The flash output is adjustable from 1/1 full power to 1/128th power

in 1/3rd stop increments. To obtain a correct flash exposure, use a

hand-held flash meter to determine the required flash output.

Flash Mode -- M: Manual Flash

Press < MODE > button so

1 that < M > is displayed.

Turn the Select Dial to choose

2 a desired flash output amount.

Press < SET > button again to

3 confirm the setting.

Figures displayed when reducing flash output level→

←Figures displayed when increasing flash output level

1/41/21/1

1/1-0.3

1/2+0.7

1/1-0.7

1/2+0.3

1/2-0.3

1/4+0.7

1/2-0.7

1/4+0.3

······

Flash Output Range

The following table makes it easier to see how the stop changes in

terms of f/stop when you increase or decrease the flash output. For

example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-

0.7, and then increase the flash output to more than 1/2, 1/2+0.3,

1/2+0.7, and 1/1 will be displayed.

Optical S1 Secondary Unit Setting

In M manual flash mode, press Function Button 3 < > button so

that this flash can function as an optic S1 secondary flash with optic

sensor. With this function, the flash will fire synchronously when the

main flash fires, the same effect as that by the use of radio triggers.

This helps create multiple lighting effects.

Optical S2 Secondary Unit Setting

Press Function Button 3 < > button so that this flash can also

function as an optic S2 secondary flash with optic sensor in M

manual flash mode. This is useful when cameras have pre-flash

function. With this function, the flash will ignore a single “preflash”

from the main flash and will only fire in response to the second,

actual flash from the main unit.

● S1 and S2 optical triggering is only available in M manual

flash mode.

Manual Off Camera High-speed Setting

In M manual flash mode, press Function Button 4< > button to

select high-speed mode and is displayed.

SYNC

S1/S2

- 39 - - 40 -

Wireless Flash Shooting: Radio (2.4G) Transmission

● You can set up three slave groups for TTL autoflash shooting.

With TTL autoflash, you can easily create various lighting effects.

● Any flash settings for the slave units on the master flash in

TTL/Manual/Multi mode will be automatically sent to the slave

units. So the only thing you need to do is to set the master unit for

each slave group without any operation for the slave units at all

during the shooting.

● This flash can work in TTL /M /Multi / OFF flash modes when set

as a master unit.

As a slave unit, V860IIF is compatible with Godox X1 series

transmitter e.g. X1T-C(For Canon), X1T-N(For Nikon), X1T-S(For

Sony), X1T-F(For Fuji), X1T-O(For Olympus or Panasonic).

Master Unit Setting

1. Wireless Settings

You can switch between normal flash and wireless flash. For normal

flash shooting, be sure to set the wireless setting to OFF.

Press < > button so that

1 < > is displayed on the

LCD panel. If < MULTI>

is displayed, it means Multi

mode is ON.

The backlight turns green

2 now.

● Even with multiple slave units, the master unit can control

all of them via wireless.

● In this user manual, “master unit” refers to the camera flash

on a camera and “slave unit” will be controlled by the

master unit.

Press Function Button 4

1 < > to choose the

group from M/A/B/C. Then,

press Function Button 3

<MODE> so that the master

unit can work in OFF/TTL/M

flash mode. Choose one of

them as the flash mode of

master unit.

3. Setting the Communication Channel

If there are other wireless flash systems nearby, you can change the

channel IDs to prevent signal interference. The channel IDs of the

master unit and the slave unit(s) must be set to the same.

Press Function Button 3

1 < > and turn the

Select Dial to choose a

channel ID from 1 to 32.

Press the <SET> button to

2 confirm.

2. Setting Master Unit’s Flash Mode

Press < > button to

2 switch to Multi mode.

Autoflash Shooting with One Slave Unit

5. TTL: Fully Automatic Wireless Flash Shooting

Master Unit Setting

● Attach a V860IIF camera

flash on the camera and

set it as the master unit.

(Page 39)

● M/A/B/C can be set as

TTL mode independently.

60-200

1/4

1/8

1/16

1/32

1/64

1/128

100

6-7

8-9

12-14

20-50

15-19

Maximum Stroboscopic Flashes:

Flash

output

Slave Unit Setting

Press < > button so that

< > and < > are

displayed on the LCD panel.

The backlight turns orange

2 now.

4. Wireless ID Settings

Change the wireless channels and wireless ID to avoid interference

for it can only be triggered after the wireless IDs and channels of the

master unit and the slave unit are set to the same.

Press the <MENU> button to enter C.Fn ID. Press the <SET> button

to choose OFF channel expansion shutdown, and choose any figure

from 01 to 99.

- 41 - - 42 -

Setting <Multi>

1 stroboscopic flash.

● Press <MODE> button so

that < MULTI> is

displayed.

● Setting the stroboscopic

flash.

Slave Unit Setting

● Set the other camera

flash as the wireless slave

unit. (Page 40)

● The slave unit can be set

as A/B/C.

Check the communication

3 channel

● If the master unit and

slave unit(s) are set to a

different channel, set them

to the same channel.

(Page 40)

Position the camera and

4 flashes

● Position the camera and

flashes as the picture

shows. (Page 43)

Check that the flash is

5 ready

● Check that the master

flash ready indicator is

lightened.

● When the slave flash

ready indicator is ready,

the AF-assist beam

lighting area will blinks at

1 second intervals.

Check the flash operation

● Press the master unit’s

Test Button < >.

● Then, the slave unit will

fire. If not, check whether

the slave unit is put in the

right position or not.

The slave unit might be out of order or fire an unwanted flash

due to the nearby fluorescent lamp or computer screen.

● If the slave unit’s auto power off function is workable, press

the master unit’s test button to power it on. Please note that

test firing is unavailable during the camera’s regular

metering time.

● The effective time of slave auto power off is changeable.

(C.Fn-Sv APOT/ Page 47)

● By making some settings, the auto AF-assist transmitter will

not blink after the slave unit’s flash ready indicator is

lightened. (C.Fn-AF/ Page 47)

Using Fully Automatic Wireless Flash

The FEC and other settings that set on the master unit will also be

appeared on the slave unit automatically. The slave unit does not

need any operation. Use the following settings to make wireless

flashes according to the same methods with normal flash shooting.

● Flash Exposure Compensation （ / Page 35）

About Master Unit

Use two or more master units. By preparing several cameras that

with master units flash attached, cameras can be changed in

shooting while keeping the same lighting source (slave unit).

6. M: Wireless Flash Shooting with Manual Flash

This describes wireless (multiple shooting) using manual flash. You

can shoot with a different flash output setting for each slave unit

(firing group). Set all parameters on the master unit.

Setting the flash mode to

1 <M>

● Press Function Button 4

< > to choose groups.

Then, press Function

Button 3 < MODE > to set

the flash to M mode.

Setting flash output

● When choosing the state

of the group, press

Function Button 2 < >

to set the power output.

Turn the Select Dial to set

the flash output of the

groups. Press the <SET>

button to confirm.

Taking the picture

● Each group fires at the set

flash ratio.

Using a flash (master/slave) with a radio transmission wireless

shooting function make it easy to shoot with advanced wireless

multiple flash lighting, in the same way as TTL autoflash shooting.

The basic relative position and operation range are as shown in the

picture. You can then perform wireless TTL autoflash shooting just

by setting the master unit to <TTL>.

7. Multi: Manual Wireless Flash Shooting

- 43 - - 44 -

Transmission distance is about 100m.

● Use the supplied mini stand to position the slave unit.

● Before shooting, perform a test flash and test shooting.

● The transmission distance might be shorter depending on

the conditions such as positioning of slave units, the

surrounding environment and whether conditions.

You can divide the slave units into two or three groups and perform

TTL autoflash while changing the flash ratio (factor). In addition, you

can set and shoot with a different flash mode for each firing group,

for up to 5 groups.

Wireless Multiple Flash Shooting

● Auto Shooting with Two Slave Groups

● Auto Shooting with Three Slave Groups

Positioning and Operation Range (Example of wireless flash

shooting)

● Autoflash Shooting with One Slave Unit

Other Applications

Wireless Control Function

The flash unit is built in with a Wireless Control Port so that you can

wirelessly adjust the power level of the flash and the

flash triggering.

To control the flash wirelessly, you need a FT-16S

remote control set (on-camera and on-flash). Insert its

receive end into the Wireless Control Port on the flash

and insert the transmit end into the camera hot shoe.

Settings made on the hotshoe-mounted

transmit and receive ends will be wirelessly

communicated to the flash. Then

you can press the camera

shutter release button to

trigger the flash. You can also

hold the transmit end at hand

to control your off-camera flash.

For full instructions on the use of FT series remote control, see its user

manual.

Sync Triggering

The Sync Cord Jack is a Φ2.5mm plug. Insert a trigger plug here

and the flash will be fired synchronously with the camera shutter.

Auto Focus Assist Beam

In poorly-lit or low-contrast shooting environments, the built-in auto

focus assist beam will automatically light on to make it easier for

autofocus. The beam will light up only when autofocus is difficult

and get out as soon as the autofocus becomes correct.

If you want to turn off the auto focus assist beam, set the “AF” to

“OFF” on the C.Fn settings.

● If you find the auto focus assist beam does not light up, this

is because the camera has got a correct autofocus.

● The auto focus assist beam can only start up in the slow

shutter.

Position

Center

Periphery

Effective Range

0.6~10m / 2.0~32.8 feet

0.6~5m / 2.0~16.4 feet

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base

station, 2.4G wifi router, Bluetooth, etc.)

　 → To adjust the channel CH setting on the flash trigger (add 10+ channels) and

use the channel which is not disturbed. Or turn off the other 2.4G equipment in

working.

2. Please make sure that whether the flash has finished its recycle or caught

up with the continuous shooting speed or not(the flash ready indicator is

lighten) and the flash is not under the state of over-heat protection or

other abnormal situation.

→Please downgrade the flash power output. If the flash is in TTL mode, please

try to change it to M mode(a preflash is needed in TTL mode).

3. Whether the distance between the flash trigger and the flash is too close

or not

→Please turn on the “close distance wireless mode” on the flash trigger (＜0.5m):

X1 series: press the test button and hold on, then turning it on until the flash

ready indicator blinks for 2 times.

XPro series: Set the C.Fn-DIST to 0-30m.

4. Whether the flash trigger and the receiver end equipment are in the low

battery states or not

　 →Please replace the battery(the flash trigger is recommended to use 1.5V

disposable alkaline battery).

- 45 - - 46 -

Bounce Flash

By pointing the flash head toward a wall or ceiling, the flash will

bounce off the surface before illuminating the subject. This can

soften shadows behind the subject for a more natural-looking shot.

This is called bounce flash.

To set the bounce direction, hold the flash head and turn it to a

satisfying angle.

360

-7-90

● If the wall or ceiling is too far away, the bounced flash might

be too weak and result in underexposure.

● The wall or the ceiling should be a plain, white color for

high reluctance. If the bounce surface is not white, a color

cast may appear in the picture.

Creating a Catchlight

With the catchlight panel, you can create a catchlight in the subject’s

eyes to add life to the facial expression.

Point the flash head upward

1 by 90°.

Pull out the wide panel. The

2 catchlight panel will come out

at the same time.

Push the wide panel back in.

● Push in only the wide panel.

● Follow the same procedures

as for bounce flash.

● Point the flash head straight ahead and then upward by

90°. The catchlight will not appear if you swing the flash

head left or right.

● For best catchlight effect, stay 1.5m/4.9ft away from the

subject.

ZOOM: Setting the Flash Coverage and Using

the Wide Panel

The flash coverage can be set automatically or manually. It can be

set to match the lens focal length from 20 mm to 200mm (135

system). Also, with the built-in wide panel, the flash coverage can

be expanded for 12mm wide-angle lenses.

Choose APS or 135 system in the C.Fn-AP.

In Manual Zoom mode, press the

<ZOOM/C.FN> button.

● Turn the Select Dial to change

the flash coverage.

● If < > is displayed, the flash

coverage will be set

automatically.

If you set the flash coverage manually, make sure it covers

the lens focal length so that the picture will not have a dark

periphery.

Using the Wide Panel

Pull out the wide panel and place it

over the flash head as shown. The

flash coverage will then be extended

to 12 mm.

● The catchlight panel will come out

at the same time. Push the

catchlight panel back in.

● The <ZOOM/C.FN> button will not

work.

Low Battery Warning

If the battery power is low, < >

will appear and blink on the LCD

panel. Please replace the battery

immediately.

- 47 - - 48 -

C.Fn: Setting Custom Functions

The following table lists the available and unavailable custom

functions of this flash.

m/ft

APO

Sv APOT

BEEP

LIGHT

LCD

ZOOM

Sv LED

OFF

60min

30min

OFF

12sec

OFF

0~9

A PS

135

OFF

01-99

OFF

Distance indicator

Auto power off

AF-assist beam

Slave auto power

off timer

Beeper

Backlighting time

LCD contrast ratio

ZOOM display

format

Wireless ID

Wireless LED Lamp

C.Fn Custom Functions

Custom Function

Signs

Function

Setting No. Settings & Description

feet

OFF

60min

30min

OFF

Off in 12 sec.

Always off

Always lighting

10 levels

APS system

135 system

Off

Choose any figure

from 01-99

Off

1. Press <Zm/C.Fn> Backlight/Custom Setting Button for 2 seconds

or longer until C.Fn menu is displayed. The “Ver x.x” in the top-

right corner refers to the software version.

2. Select the Custom Function No.

● Turn the Select Dial to select the Custom Function.

3. Change the Setting.

● Press<SET> button and the Setting No. blinks.

● Turn the Select Dial to set the desired number. Pressing <SET>

button will confirm the settings.

● After you set the Custom Function and press <MODE> button,

the camera will be ready to shoot.

4. In the C.Fn states, long press the “Clear” button for 2 seconds

until “OK”is displayed on the panel, which means the values in

C.Fn can be reset.

Protection Function

1. Over-Temperature Protection

● To avoid overheating and deteriorating the flash head, do not fire

more than 30 continuous flashes in fast succession at 1/1 full

power. After 30 continuous flashes, allow a rest time of at least 10

minutes.

● If you fire more than 30 continuous flashes and then fire more

flashes in short intervals, the inner over-temperature protection

function may be activated and make the recycling time over 10

seconds. If this occurs, allow a rest time of about 10 minutes, and

the flash unit will then return to normal.

● When the over-temperature protection is started, is shown on

the LCD display.

Number of flashes that will activate over-temperature protection:

Meaning

A failure occurs on the recycling system so that the

flash cannot fire.

Please restart the flash unit. If the problem still exists,

please send this product to a maintenance center.

The system gets excessive heat. Please allow a rest

time of 10 minutes.

The voltage on two outlets of the flash tube is too high.

Please send this product to a maintenance center.

There are some errors occurred during the upgrading

process. Please using the correct firmware upgrade

method.

Prompts on LCD Panel

2. Other Protections

The system provides real-time protection to secure the device and

your safety. The following lists prompts for your reference:

Number of flashes that will activate over-temperature protection in

high-speed sync triggering mode:

Power Output Level

1/1

1/2 +0.7

1/2 +0.3

1/2

1/4(+0.3,+0.7)

1/8(+0.3,+0.7)

1/16(+0.3,+0.7)

1/32(+0.3,+0.7)

1/64(+0.3,+0.7)

1/128(+0.3,+0.7)

Number of Flashes

100

200

300

500

1000

Power Output

1/1

1/2(+0.3,+0.7);

1/4(+0.3,+0.7)

1/8(+0.3,+0.7);

1/16(+0.3,+0.7)

1/32(+0.3,+0.7);

1/64(+0.3,+0.7);

1/128(+0.3,+0.7);

Times

Firmware Upgrade

This flash supports firmware upgrade through the USB port. Update

information will be released on our official website.

USB connection line is not included in this product. The USB

port is a standard Micro USB socket. Common USB

connection line is applicable.

- 49 - - 50 -

11.1V/2000mAh Li-ion polymer battery

< 1.5 seconds. Red LED indicator will light up when the

flash is ready.

Technical Data

V860IIF

Fuji cameras (refer to compatible camera models)

60 (m ISO 100)

190 (feet ISO 100)

20 to 200mm (135 system) or 14 to 133mm (APS)

• Auto zoom (Flash coverage set automatically

to match the lens focal length and image size)

• Manual zoom

• Swinging/tilting flash head (bounce flash): 0 to 360°

horizontally and -7° to 90° vertically

1/300 to 1/20000 seconds

TTL autoflash and manual flash

Manual. FEB: ±3 stops in 1/3 stop increments

(Manual FEC can be combined.)

High-speed sync (up to 1/8000 seconds),

first-curtain sync, and second-curtain sync

Provided (up to 100 times, 200Hz)

Master, Slave, Off

3 (A, B and C)

≤100m

32 (1~32)

Two red indicators blink

Center: 0.6~10m / 2.0~32.8 feet

Periphery: 0.6~5m / 2.0~16.4 feet

Approx. 650

Power off automatically after approx. 90 seconds

of idle operation. (60 minutes if set as slave)

Hotshoe, 2.5mm sync line, Wireless control port

5600±200k

64*76*190 mm

420g

540g

Model

• Type

Compatible Cameras

Guide No.

(1/1 output @ 200mm)

Flash Coverage

Flash Duration

• Exposure Control

Exposure control system

Flash exposure

compensation (FEC)

Sync mode

Multi flash

• Wireless Flash (Optical transmission and 2.4G transmission)

Wireless flash function

Controllable slave groups

Transmission range

(approx.)

Channels

Slave-ready indicator

• Auto Focus Assist Beam

Effective range (approx.)

• Power Supply

Power source

Recycle time

Full power flashes

Power saving

• Sync Triggering Mode

• Color Temperature

• Dimensions

W x H x D

Weight without battery

Weight with battery

Troubleshooting

If there is a problem, refer to this Troubleshooting Guide.

The Camera Flash cannot be charged.

● The battery is installed in the wrong direction.

→Install the battery in the correct direction.

● The camera flash’s internal battery is exhausted.

→If < > appears and blinks on the LCD panel, replace the

battery immediately.

The Camera Flash does not fire.

● The camera flash is not attached securely to the camera.

→Attach the camera’s mounting foot securely to the camera.

● The electrical contacts of the Camera Flash and camera are dirty.

→Clean the contacts.

The power turns off by itself.

● After 90 seconds of idle operation, auto power off took effect if the

flash is set as master.

→Press the shutter button halfway or press any flash button to

wake up.

● After 60 minutes (or 30 minutes) of idle operation, the flash unit

will enter sleep mode if it is set as slave.

→Press any flash button to wake up.

Auto zoom does not work.

● The camera flash is not attached securely to the camera.

→Attach the camera flash’s mounting foot to the camera.

The flash exposure is underexposed or overexposed.

● You used high-speed sync.

→With high-speed sync, the effective flash range will be shorter.

Make sure the subject is within the effective flash range

displayed.

● You used Manual Flash mode.

→Set the flash mode to TTL or modify the flash output.

Photos have dark corners or only parts of the target subject

are illuminated.

● The focal length of lens exceeds the flash coverage.

→Check the flash coverage you set. This flash unit has the flash

coverage between 20 and 200mm, which fits medium-format

cameras. Pull the wide panel out to extend the flash coverage.

- 51 - - 52 -

● Shut down the device immediately should abnormal operation be

detected.

● Avoid sudden impacts and the product should be dedusted

regularly.

● It is normal for the flash tube to be warm when in use. Avoid

continuous flashes if unnecessary.

● Maintenance of the flash must be performed by our authorized

maintenance department which can provide original accessories.

● This product, except consumables e.g. flash tube, is supported

with a one-year warranty.

● Unauthorized service will void the warranty.

● If the product had failures or was wetted, do not use it until it is

repaired by professionals.

● Changes made to the specifications or designs may not be

reflected in this manual.

Maintenance

Any Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. This transmitter must not be co-

located or operating in conjunction with any other antenna or

transmitter.

FCC Warning

Godox VING TTL Li-ion Camera Flash for Fuji V860IIF User manual

Brand: Godox

Model: VING TTL Li-ion Camera Flash for Fuji V860IIF

Category: Camera flashes

Type: User manual

This manual is also suitable for

V860II-F 2.4G TTL Flash for Fuji Camera GN60 HSS 1/8000s 1.5S Recycle Time 650 Full Power Pops 22 Steps of Power Output Round Flash Head S-R1 Magnetic Modifier Adapter

Download PDF

report

Godox VING TTL Li-ion Camera Flash for Fuji V860IIF User manual

This manual is also suitable for

Godox VING TTL Li-ion Camera Flash for Fuji V860IIF User manual

Related papers

Other documents