iON Street Light Controller Owner's manual

iON
Brand
iON
Model
Street Light Controller
Type
Owner's manual

iON Street Light Controller is a unique device that automates the switching on and off of street lights based on sunset and sunrise times, eliminating the need for manual intervention and ensuring optimal lighting conditions.

Key features of the iON Street Light Controller include:

Automatic switching: The controller automatically turns on street lights at sunset and turns them off at sunrise, adjusting to the changing sunset and sunrise times throughout the year. This ensures that streets are well-lit when needed, while saving energy during daylight hours.

Phase failure detection: The controller monitors the electrical phases and automatically switches to the next available phase in case of a phase failure. This ensures uninterrupted lighting, even in the event of power outages or fluctuations.

iON Street Light Controller is a unique device that automates the switching on and off of street lights based on sunset and sunrise times, eliminating the need for manual intervention and ensuring optimal lighting conditions.

Key features of the iON Street Light Controller include:

Automatic switching: The controller automatically turns on street lights at sunset and turns them off at sunrise, adjusting to the changing sunset and sunrise times throughout the year. This ensures that streets are well-lit when needed, while saving energy during daylight hours.

Phase failure detection: The controller monitors the electrical phases and automatically switches to the next available phase in case of a phase failure. This ensures uninterrupted lighting, even in the event of power outages or fluctuations.

Make sure you read this operating manual before using the SUNRISE TIMER.
Store this operating manual safely so that you can use it in future.
2
TABLE OF CONTENTS
1. GETTING STARTED..................................................................................................... 3
1.1 SALIENT FEATURES ............................................................................................. 3
1.2 SPECIFICATION ..................................................................................................... 3
2. OPERATING THE SUNRISE TIMER .......................................................................... 4
2.1 CONNECTION DETAILS ....................................................................................... 4
2.2 OPERATING PROCEDURE ................................................................................... 5
2.3 PLEASE NOTE......................................................................................................... 7
3. TROUBLE SHOOTING ................................................................................................. 7
LIST OF FIGURES
Figure 1: Front panel of Sunrise Timer. .............................................................................. 4
Figure 2:Connection Diagram for Master Relay & SSR..................................................... 5
3
1. GETTING STARTED
This is a unique concept of automatic switching “ON” the street lights after sunset &
switching them “OFF” on dawn or sunrise.
No need to depend on Watchman’s memory and alertness.
As sunrise and sunset timings changes from city to city depending on their location on
longitude, this system automatically adjusts itself with sunrise and sunset as per the city
location.
o Can handle many Street Lights (depends on contactor).
o Three built in relays to control three different contactor to distribute load on three
phases.
o Phase Failure Detection: Automatic switch on to next phase
o Manual ON facility in case of emergency
o Battery Backup
1.1 SALIENT FEATURES
1. Size: 193mm ,193mm
2. 24 Hours Real Time Clock
3. Twilight Adjustment up to 4 Hours
4. Delay To Twilight up to 8 Hours
5. Date Selection
6. Blackout Selection Actual Time
7. Phase Selection
8. Phase Activation Time
9. Battery Backup for a period of 2 years
10. Phase Manual “ON” switch
11. Three Phase indication LED
1.2 SPECIFICATION
1. Operating voltage: 180 to 230 V AC +
15% 50 Hz.
2. Accuracy: Quartz Crystal.
3. Display Time Real time.
4. Relay Output: 5 Amp resistive.
2. OPERATING THE SUNRISE TIMER
M
Figure 1
: Front panel of Sunrise Timer
2.1 CONNECTION
DETAILS
On the top there are two connectors; one is for three phase connection & second for
common of all three phase relays.
Refer the figure given below.
• Connect “r-
phase” to “r” , connect
“b”.connect “neutral” to “n” point & “earth” to “e” point.
• Connect “r-
phase” load to “rr”, “y
Check all the connections & switch on the mains supply.
• Now display
is showing real time in ( hh:mm).Three leds on the left of the display are
showing that all three phases are active. Three more leds on the top are given to
indicate the relay ON status. Three switches are given for relay on.
+
+
+
MANUAL
ON
Y R B
+
+
+
R
Y
B
PHASE MONITOR
+
+
+
R
Y
B
LOAD
+
+
+
MANUAL
ON
Y R B
+
+
+
R
Y
B
PHASE MONITOR
+
+
+
R
Y
B
LOAD
4
2. OPERATING THE SUNRISE TIMER
Hrs
: Front panel of Sunrise Timer
.
DETAILS
On the top there are two connectors; one is for three phase connection & second for
common of all three phase relays.
Refer the figure given below.
phase” to “r” , connect
“y-phase” to “y” & connect “b-
phase” to
“b”.connect “neutral” to “n” point & “earth” to “e” point.
phase” load to “rr”, “y
-phase” load to “ry” & “b-
phase” load to “rb” point.
Check all the connections & switch on the mains supply.
is showing real time in ( hh:mm).Three leds on the left of the display are
showing that all three phases are active. Three more leds on the top are given to
indicate the relay ON status. Three switches are given for relay on.
ST LIGHT
TIMER
T193SL
1
2
3
4
5
6
SET
1
2
3
4
5
6
SET
Mts
On the top there are two connectors; one is for three phase connection & second for
phase” to
phase” load to “rb” point.
is showing real time in ( hh:mm).Three leds on the left of the display are
showing that all three phases are active. Three more leds on the top are given to
ST LIGHT
TIMER
T193SL
7
8
ENT
7
8
ENT
5
193SL
R
Y
B
TO LAMP POLES
R-PHASE
Y-PHASE
B-PHASE
NEUTRAL
EARTH
NEUTRAL
EARTH
R
Y
B
RC
R,Y,B SHOWN HERE ARE COMING
FROM MAINS “R-PHASE”,”Y-PHASE”
“B-PHASE”
CONTACTOR
NEUTRAL
COIL
MCB
(MAIN SWITCH)
Figure 2:Connection Diagram for Master Relay & SSR
2.2 OPERATING PROCEDURE
v Clock setting
• Push the “SET” key.
• Clock led will glow & display will disappear.
• Push the “ENT” key now.
• The display will show previously set clock (time) & thousand place digit will start
flashing. One can set only flashing digit from ( 0 to 9 ) by (up arrow) key.
• Push ((left arrow) key, now the hundredth place digit will flash.Set this digit
by “up” key from ( 0 to 9).Again push “left arrow” key to go to next digit.
• Thus one can set the real time by following the above procedure.
• Push “ENT” key to store the new time & to go to the normal mode where display
shows the real time.
v Date setting
• Push the “SET” key in the normal mode.
• Clock led will glow & display will disappear.
• Push “left arrow” key. Now date led will glow.
• Push “ENT” key to set date. Here, the year will be displayed first & thousand
place digit will start flashing. Again set this display with “up” key from ( 0 to 9 ).
• To go to the next digit push the “left arrow” key & set it by the “up” key from
(0 to 9). Repeat the same procedure to set the next two digits.
• Push “ENT” key. Now the display will show date & month. First set date as per
above procedure & then month.
• Push “ENT” key to save these values. Display will now go to the normal mode.
6
v Twilight setting
• Push “SET” key in the normal mode.
• Clock led will glow & display will disappear.
• Push “left arrow” key twice. Now twilight led will glow.
• Push “ENT” key. Thousand place digit will flash. Do not set this digit, just skip it.
• Push “left arrow” key. Now hundred place digit will flash. Set it by “up” key from
( 0 to 9).
• This time is settable up to 4 hours & 00 mins .Set the next digits by following
above procedure.
• If one has set twilight to (00:30) then lights will be ON 30 mins after sunset &
will be OFF 30 mins before sunrise.
v Delay setting
• Push “SET” key in normal mode.
• Clock led will glow & display will disappear.
• Push “left arrow” key thrice. Now delay led will glow.
• Push “ENT” key. Thousand place digit will flash. Do not set this digit, just skip it.
• Push “left arrow” key. Now hundred place digit will flash. Set it by “up” key from
( 0 to 9).
• This time is settable upto 8 hours & 00 mins. Set the next digits by following the
above procedure.
• If one has to set a delay of (01:00) then lights will be ON 1.00 hour after twilight
time after sunset & will be OFF as per sunrise time or before set twilight time.
v Blackout setting
• This time is to switch off all relays connected to each phase after a particular set
time. This is a real time based setting.
• Push “SET” key in normal mode.
• Clock led will glow & display will disappear.
• Push “left arrow” key four times. Now blackout led will glow.
• Push “ENT” key. Thousands place digit will flash. Set this display with “up” key
from ( 0 to 9).
• Push “left arrow key” now hundreds place digit will flash. Set it by “up” key from
( 0 to 9).This time is settable in real time format. Set next digits by following
the above procedure.
v Phase sel
• Here one can deactivate phase from “r” , “y” ,”b” after the set time
• Push the “SET” key in normal mode.
• Clock led will glow & display will disappear.
• Push “left arrow” key five times.Now phase sel led will glow.
• Push “ENT” key .Now previously set phase will flash on the display.
• One can change the phase setting by “up” key.
• If one has set “r” phase then on 1st of Jan, this phase will be off after the phase
deactivation time. “y” phase will be off on 2nd Jan & “b” phase will be off on 3rd
jan after the set time. Again on 4th Jan “r” phase will be off. This cycle will
continue for the year.
7
v Phase dact
• This setting is in real time mode. To switch off the phase after particular time,this
setting is applicable.
• Push “SET” key in normal mode.
• Clock led will glow & display will disappear.
• Push “left arrow” key six times. Now phase dact led will glow.
• Push “ENT” key. Thousandplace digit will flash . Set it by “up” key from (0 to 9).
• Push “left arrow key”. Now hundred place digit will flash. Set it by “up” key from
( 0 to 9).Set the next digits by following the above procedure.
• If one has to set phase dact time as (00:30) then one phase will be off 30 mins
after 00:00.
To disable any of the above setting, set those set points to 00:00.
Display will go to normal mode from set mode after 20 seconds ,if no key is
pressed in set mode.
2.3 PLEASE NOTE
If load is inductive,
connect snubber across load
SNUBBER
R=56 OHMS / 2 WATT.
C=0.1 MFD / 250 V AC
TC=TEMPERATURE CONTROLLER
TC
LOAD
L
N
COM
NO
R C
3. TROUBLE SHOOTING
1. Sensor open indication
: Display shows “Err1” for cabinet & “Err2” for cascade
2. Sensor reverse
: If the RTD is not connected as per connection diagram then it will
show erratic temperature.
3. Not showing proper temp
: Loose connection on terminal or calibration problem.
4. Problem in relay operation
: Check connection as per wiring diagram given.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

iON Street Light Controller Owner's manual

iON
Brand
iON
Model
Street Light Controller
Type
Owner's manual

iON Street Light Controller is a unique device that automates the switching on and off of street lights based on sunset and sunrise times, eliminating the need for manual intervention and ensuring optimal lighting conditions.

Key features of the iON Street Light Controller include:

Automatic switching: The controller automatically turns on street lights at sunset and turns them off at sunrise, adjusting to the changing sunset and sunrise times throughout the year. This ensures that streets are well-lit when needed, while saving energy during daylight hours.

Phase failure detection: The controller monitors the electrical phases and automatically switches to the next available phase in case of a phase failure. This ensures uninterrupted lighting, even in the event of power outages or fluctuations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents