Simplicity 076356-02 User manual

Type
User manual
Not for
Reproduction
ComAp InteliLite NT
®
System Controller Manual
Standby Generator System
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All Rights Reserved.
80021814USCN
Revision B
Not for
Reproduction
Table of Contents
System Controller ...............................3
Display Screen Structure .........................4
Alarms .........................................5
Browsing ECU Alarms............................5
Setpoint Change ................................6
Entering Password ..............................6
Controller Information Screen .....................7
Display Contrast Adjust ..........................8
Not for
Reproduction
3
Position Button Description
A Start Button Works in MANUAL MODE only. Press this button to initiate the start sequence
of the engine.
B Stop Button Works in MANUAL MODE only. Press this button to initiate the stop sequence
of the engine. Repeated pressing or holding the button for more than 2
seconds will cancel current phase of the stop sequence (like ramping the
power down or cooling) and next phase will continue.
C Fault Reset Use this button to acknowledge alarms and deactivate the horn output. Inactive
alarms will disappear immediately and status of active alarms will be changed
to “confirmed” so they will disappear.
D Horn Reset Use this button to deactivate the horn output without acknowledging the alarms.
E Supplying Load This LED is not used on these models.
F Ready / Auto Indicates the generator is in AUTO mode and ready for operation.
G Warning Indicates a generator warning is present.
H Running Indicates generator is running.
J Not in Auto Indicates the generator is not in AUTO mode.
K Alarm Indicates a generator alarm is present.
L Enter Button Use this button to finish editing a setpoint or moving “right” in the history page.
M Down Button Use this button to move down or decrease a value.
N Up Button Use this button to move up or increase a value.
P Page Button Use this button to switch over display pages.
R LCD Display Black/White display screen.
S Mode Left Use this button to change the mode. The button works only if the main screen
with the indicator of currently selected mode is displayed.
T Mode Right Use this button to change the mode. The button works only if the main screen
with the indicator of currently selected mode is displayed.
A
M
N
B
C
D
L
P
TS
K
J H
G F E
R
System Controller
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Generator
L1N 0 L1L2 0V
L1N 0 L1L2 0V
L1N 0 L1L2 0V
Gen freq 0.0Hz
0 0 0 A
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
ECU AlarmList
>EngOil Press
000225 (000E1h)
FC 100 OC 4 FMI 1
AlarmList 1
Emergency Stop
Password
>Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
Page
Gen-set Name
>Nominal Power
200 kW
Nomin Current
350 A
CT Ratio
2000 /5A
Gen-set Name
>Nominal Power
250 200 kW
Nomin Current
350 A
CT Ratio
2000 /5A
No. Reason
> 0 Switched On
-1 Fault reset
-2 Emergency Stop
-3 Wrn RA15 Fail
-4 Sprinkler Set
-5 Config Loaded
13:02:17 07/08/2008
Time Date
>13:02:17 07/08/2008
13:00:46 07/08/2008
13:00:46 07/08/2008
13:00:45 07/08/2008
13:00:45 07/08/2008
13:00:43 07/08/2008
0 Switched On
Mode RPM Pwr
> OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
0 Switched On
Page
Page
Page
Page
Page
Page
Page
Enter
Enter
Enter
Enter
Page
Enter
Enter Page
MEASUREMENT SETPOINTS HISTORY LOG
V
Display Screen Structure
The displayed information is structured into pages and
screens.
Use the PAGE button to switch over the pages.
1. The Measurement page consists of screens
that display measured values including voltage,
current, and oil pressure, and computed values
including generator power, statistical data, and
alarms.
2. The Setpoints page contains all setpoints
organized in groups, including a group for entering
a password.
3. The History Log page shows the operation history
with the most recent item listed first.
Not for
Reproduction
5
alarm
deactivation
ECU AlarmList
>*EngOil Press
*EngCool Temp
Coolant Level
FC 100 OC 4 FMI 1
ECU AlarmList
>EngOil Press
Coolant Level
FC 100 OC 4 FMI 1
ECU AlarmList
>
FC 0 OC 0 FMI 0
ECU AlarmList
*EngOil Press
>*EngCool Temp
Coolant Level
FC 110 OC 1 FMI 0
Enter
ECU AlarmList
*EngOil Press
*EngCool Temp
>Coolant Level
FC 111 OC 2 FMI 2
Enter
Enter
Enter +
Fault
reset
ECU AlarmList
>*EngOil Press
*EngCool Temp
FC 100 OC 4 FMI 1
Enter +
Fault
reset
alarm
deactivation
AlarmList 3
*MCB Fail
*Emergency Stop
Sd Override
Inactive unconfirmed alarm
Active unconfirmed alarm
Active confirmed alarm
Alarms
Browsing ECU Alarms
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
Password
>Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
Enter
Page
Enter
Enter Page
Page
Gen-set Name
>Nominal Power
200 kW
*Nomin Current
350 A
CT Ratio
2000 /5A
Gen-set Name
>Nominal Power
250 200 kW
*Nomin Current
350 A
CT Ratio
2000 /5A
V
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
>Password
Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
>EnterPassword
Changepassword
Enter
Page
Enter
Enter Page
>EnterPassword
0
Changepassword
Page
V
Setpoint Change
Entering Password
Not for
Reproduction
7
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
InteliLite NT
ComAp 2007-2008
IL-NT-x.y
Serial:12345678
SW ver: x.y, x.y
Appl : AMF25
Branch: Standard
Page
Languages
>English
Chinese
Enter + Page
User interface:
User
>Engineer
Serial: 12345678
Pwd. dec.: 1234567890
Page
Page
Enter
Enter
V
Controller Information Screen
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Display Contrast Adjust
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
Enter +
Enter +
Notready
RPM 0
No Timer
0 0
OFF MAN AUT
Notready
RPM 0
No Timer
V
V
V
Not for
Reproduction
ComAp InteliLite NT
®
Manual del sistema de control
Generador de reserva
Copyright © Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, EE. UU. Todos los derechos reservados.
80021814USCN
Modificación A
Not for
Reproduction
12 BRIGGSandSTRATTON.COM
Generator
L1N 0 L1L2 0V
L1N 0 L1L2 0V
L1N 0 L1L2 0V
Gen freq 0.0Hz
0 0 0 A
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
ECU AlarmList
>EngOil Press
000225 (000E1h)
FC 100 OC 4 FMI 1
AlarmList 1
Emergency Stop
Password
>Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
Page
Gen-set Name
>Nominal Power
200 kW
Nomin Current
350 A
CT Ratio
2000 /5A
Gen-set Name
>Nominal Power
250 200 kW
Nomin Current
350 A
CT Ratio
2000 /5A
No. Reason
> 0 Switched On
-1 Fault reset
-2 Emergency Stop
-3 Wrn RA15 Fail
-4 Sprinkler Set
-5 Config Loaded
13:02:17 07/08/2008
Time Date
>13:02:17 07/08/2008
13:00:46 07/08/2008
13:00:46 07/08/2008
13:00:45 07/08/2008
13:00:45 07/08/2008
13:00:43 07/08/2008
0 Switched On
Mode RPM Pwr
> OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
0 Switched On
Page
Page
Page
Page
Page
Page
Page
Enter
Enter
Enter
Enter
Page
Enter
Enter Page
MEASUREMENT SETPOINTS HISTORY LOG
V
Estructura de la pantalla
La información que se muestra está estructurada en
páginas y pantallas.
Use el botón PAGE (BUSCAR) para navegar por las
páginas.
1. La página Measurement (Medición) consta de
pantallas que muestran valores medidos como
tensiones, corrientes, y presión de aceite, y
valores computados como generador de potencia,
datos estadísticos y alarmas.
2. La página Setpoints (Puntos de referencia)
contiene todos los puntos de referencia
organizados en grupos y un grupo para ingresar
una contraseña.
3. La página History Log (Registro del historial)
muestra el registro del historial ordenado de forma
tal que se muestra primero el último registro.
Not for
Reproduction
13
alarm
deactivation
ECU AlarmList
>*EngOil Press
*EngCool Temp
Coolant Level
FC 100 OC 4 FMI 1
ECU AlarmList
>EngOil Press
Coolant Level
FC 100 OC 4 FMI 1
ECU AlarmList
>
FC 0 OC 0 FMI 0
ECU AlarmList
*EngOil Press
>*EngCool Temp
Coolant Level
FC 110 OC 1 FMI 0
Enter
ECU AlarmList
*EngOil Press
*EngCool Temp
>Coolant Level
FC 111 OC 2 FMI 2
Enter
Enter
Enter +
Fault
reset
ECU AlarmList
>*EngOil Press
*EngCool Temp
FC 100 OC 4 FMI 1
Enter +
Fault
reset
alarm
deactivation
Alarmas
Exploración de alarmas ECU
AlarmList 3
*MCB Fail
*Emergency Stop
Sd Override
Inactive unconfirmed alarm
Active unconfirmed alarm
Active confirmed alarm
Alarma inactiva sin confirmar
Alarma activa sin confirmar
Alarma activa confirmada
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
Password
>Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
Enter
Page
Enter
Enter Page
Page
Gen-set Name
>Nominal Power
200 kW
*Nomin Current
350 A
CT Ratio
2000 /5A
Gen-set Name
>Nominal Power
250 200 kW
*Nomin Current
350 A
CT Ratio
2000 /5A
V
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
>Password
Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
>EnterPassword
Changepassword
Enter
Page
Enter
Enter Page
>EnterPassword
0
Changepassword
Page
V
Cambio de punto de referencia
Ingreso de contraseña
Not for
Reproduction
15
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
InteliLite NT
ComAp 2007-2008
IL-NT-x.y
Serial:12345678
SW ver: x.y, x.y
Appl : AMF25
Branch: Standard
Page
Languages
>English
Chinese
Enter + Page
User interface:
User
>Engineer
Serial: 12345678
Pwd. dec.: 1234567890
Page
Page
Enter
Enter
V
Pantalla de información del controlador
Not for
Reproduction
16 BRIGGSandSTRATTON.COM
Ajuste de contraste de la pantalla
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
Enter +
Enter +
Notready
RPM 0
No Timer
0 0
OFF MAN AUT
Notready
RPM 0
No Timer
V
V
V
Not for
Reproduction
ComAp InteliLite NT
®
Manuel du Contrôleur Système
Système de génératrice auxiliaire
Copyright © Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. Tous droits réservés.
80021814USCN
Révision A
Not for
Reproduction
20 BRIGGSandSTRATTON.COM
Les renseignements affichés sont présentés sur des
pages et des écrans.
Utilisez le bouton PAGE pour passer d’une page à
l’autre.
1. La page MESURES est composée d’écrans
qui affichent des valeurs mesurées, y compris
la tension, de courant et de pression d’huile et
les valeurs calculées, y compris la puissance
génératrice, données statistiques et alarmes.
2. La page RÉGLAGES est composée de tous les
réglages organisés en groupes et aussi un groupe
spécial pour l’entrée du mot de passe.
3. La page HISTORIQUE présente le journal de
l’historique dans l’ordre d’affichage de l’entrée la
plus récente en premier.
Generator
L1N 0 L1L2 0V
L1N 0 L1L2 0V
L1N 0 L1L2 0V
Gen freq 0.0Hz
0 0 0 A
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
ECU AlarmList
>EngOil Press
000225 (000E1h)
FC 100 OC 4 FMI 1
AlarmList 1
Emergency Stop
Password
>Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
Page
Gen-set Name
>Nominal Power
200 kW
Nomin Current
350 A
CT Ratio
2000 /5A
Gen-set Name
>Nominal Power
250 200 kW
Nomin Current
350 A
CT Ratio
2000 /5A
No. Reason
> 0 Switched On
-1 Fault reset
-2 Emergency Stop
-3 Wrn RA15 Fail
-4 Sprinkler Set
-5 Config Loaded
13:02:17 07/08/2008
Time Date
>13:02:17 07/08/2008
13:00:46 07/08/2008
13:00:46 07/08/2008
13:00:45 07/08/2008
13:00:45 07/08/2008
13:00:43 07/08/2008
0 Switched On
Mode RPM Pwr
> OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
OFF 0 0
0 Switched On
Page
Page
Page
Page
Page
Page
Page
Enter
Enter
Enter
Enter
Page
Enter
Enter Page
MEASUREMENT SETPOINTS HISTORY LOG
V
Structure de l’écran d’affichage
Not for
Reproduction
21
alarm
deactivation
ECU AlarmList
>*EngOil Press
*EngCool Temp
Coolant Level
FC 100 OC 4 FMI 1
ECU AlarmList
>EngOil Press
Coolant Level
FC 100 OC 4 FMI 1
ECU AlarmList
>
FC 0 OC 0 FMI 0
ECU AlarmList
*EngOil Press
>*EngCool Temp
Coolant Level
FC 110 OC 1 FMI 0
Enter
ECU AlarmList
*EngOil Press
*EngCool Temp
>Coolant Level
FC 111 OC 2 FMI 2
Enter
Enter
Enter +
Fault
reset
ECU AlarmList
>*EngOil Press
*EngCool Temp
FC 100 OC 4 FMI 1
Enter +
Fault
reset
alarm
deactivation
Alarmes
Parcourir d’alarmes d’ECU
AlarmList 3
*MCB Fail
*Emergency Stop
Sd Override
Inactive unconfirmed alarm
Active unconfirmed alarm
Active confirmed alarm
Alarme non confirmée inactive
Alarme non confirmée active
Alarme confirmée active
Not for
Reproduction
22 BRIGGSandSTRATTON.COM
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
Password
>Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
Enter
Page
Enter
Enter Page
Page
Gen-set Name
>Nominal Power
200 kW
*Nomin Current
350 A
CT Ratio
2000 /5A
Gen-set Name
>Nominal Power
250 200 kW
*Nomin Current
350 A
CT Ratio
2000 /5A
V
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
>Password
Basic Settings
Engine Params
Engine Protect
Gener Protect
AutoMains Fail
Extension I/O
Date/Time
>EnterPassword
Changepassword
Enter
Page
Enter
Enter Page
>EnterPassword
0
Changepassword
Page
V
Entrée de mot de passe
Changement de réglage
Not for
Reproduction
23
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
InteliLite NT
ComAp 2007-2008
IL-NT-x.y
Serial:12345678
SW ver: x.y, x.y
Appl : AMF25
Branch: Standard
Page
Languages
>English
Chinese
Enter + Page
User interface:
User
>Engineer
Serial: 12345678
Pwd. dec.: 1234567890
Page
Page
Enter
Enter
V
Écran d’information du contrôleur
Not for
Reproduction
24 BRIGGSandSTRATTON.COM
Ajustement du contraste de l’affichage
OFF MAN AUT
Not ready
RPM 0
No Timer
0 0
Enter +
Enter +
Notready
RPM 0
No Timer
0 0
OFF MAN AUT
Notready
RPM 0
No Timer
V
V
V
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Simplicity 076356-02 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI