Astria Fireplaces POLARIS Instruction Sheet

Brand: Astria Fireplaces

Model: POLARIS

Type: Instruction Sheet

This manual is also suitable for

VRE4000

Report No. 14-020 1

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

TOOLS REQUIRED

• MediumPhillipsScrewdriver

• 3/8"Open-endwrench

• 1/4"Drivesocket

GENERAL INFORMATION

Thedoorassemblyconsistsofarightandleftglasspanelassemblywith

thedoorhandlesfactorymounted.Includedisafourpiecedoorframe

witheight(8)screwsandahood(hoodpackagedseparately),whichare

requiredforassembly.Fireplaceslistedbelowonthisdocument,have

beendesignedtoacceptthesedoorswithminimumeffort.

Thesebi-foldglassdoorassemblieshavebeendesignedforusewith

andmaybeeasilyttedtoyourOutdoorGasFireplace,ModelsPolaris™

36/42,VRE4336/42,E36ODGandE42ODG.

Donotalterormodifythesedoorassembliesorareplacemalfunction

orarehazardmayresult.

ThesedoorshavebeentestedandlistedbyPFSCorperation.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

Read this instruction sheet in its entirety before beginning.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO

THESE INSTRUCTIONS.

SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL

BEFORE PROCEEDING.

HEARTHPRODUCTS

KITSANDACCESSORIES

INSTALLATION INSTRUCTIONS FOR OUTDOOR BI-FOLD GLASS DOORS

MODELS: 36LBFOD-BS (CAT. NO. H4645) AND 42LBFOD-BS (CAT. NO. H4646)

BI-FOLD GLASS DOORS

P/N 750210M

Rev. C 04/2014

Figure 1

Screen Rod

Screws

Screen And

Rod Assembly

INSTALLATION PROCEDURE

Remove Screens And Rods:

Usinga5/16"socketornutdriver,removethescreenrodassemblies(see

Figure 1).RemovethescreenrodscrewsasshowninFigure 1.Pullout

therodsfromlocatingholesonthesideofthereboxopening.

IMPORTANT! REINSTALL SCREEN ROD SCREWS INTO THE EXISTING

HOLES WHERE REMOVED.

ThescreenandrodassembliesmustnotbeinstalledwhentheBi-Fold

GlassDoorKitisinstalled.Youmaywishtoretainthescreenandrod

assembliesiscasetheBi-FoldGlassDoorKitiseverremovedinthefuture.

IMPORTANT! IF THIS OPTIONAL BI-FOLD GLASS DOOR KIT IS EVER

REMOVED, THE ROD AND SCREENS MUST BE REINSTALLED FOR SAFE

OPERATION OF THE APPLIANCE.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Place The Hood

Lip Up And

Under The Face

Top Opening

Hood Lip

Attaching Screw

(Seen From Below)

Step-1

Step-2

Face Top

Spring Clip

Screws (8)

Assembled

Door Frame

Pivot

Point

Lower

Frame

Pivot Pin Roller Pin

Lock

Figure 2

Figure 5

Figure 4

Figure 3

Hood Installation:

Begintheassemblybyinstallingthehood(packagedseparately).Be

certaintoremoveanyprotectiveplasticcoatingsforthestainlesssteel

partsbeforeinstallingthosecomponents.

Step 1. Turnoffthereplaceandallowittocoolbeforeproceeding.

Step 2. Placethehoodlipunderthefacetopopening,asshowninFigure

2 - Step 1.Attachthehoodwithtwo(2)screws,oneeachside,

asshowninFigure 2 - Step 2.

Frame Assembly:

Assemblethefourpiecedoorframewiththeeight(8)screwsprovided

asshowninFigure 3.Twospringclipsattachinsidetheuppertrack

asillustrated.

Door Installation:

Step 1. Startingwiththelowerendofeithertherightorlefthanddoor

holdthedoorataslightangletothedoorframeouteredgewith

thetoptiltedtowardthecenter.

 Swingthelowercornerofthedoorovertheholeinthelower

frameandengagethelowerpivotpinintotheholeonthelower

frameofthereboxopening(Figures 5 and 6).

Afterassembly,theframeinsertsunderthehoodasshowninFigure 4

anddropsdowninsidetheopeningwithoutfasteners.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Pivot Pin Roller Pin

Upper Door

Guide Track

Spring Clip

Fully Open or

Fully Closed

Front-Open Systems

ADJUSTMENT FOR DOOR ALIGNMENT

Thedoorsareproperlyadjustedwhenthetopdoortrimisinastraight,

levellineandthegapbetweenthedoorsisevenatthetopandbottom.

Ifadjustmentsarerequired,graspthedoorhandleandloosenthelower

doorpivotpinusinga3/8"openendwrench*.Slidethedoorpanelon

thehingepinuntilthegapbetweentheupperdoortrimandupperframe

iseven.Retightenthelowerdoorpivotpin*.Repeatthisprocedurefor

theoppositedoorifneeded.

*NOTE: Upper door pivot pins can also be loosened for adjustment

purposes; however, it is easier to loosen lower pins.

GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS

CAUTION: THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH THE

FIREPLACE OR APPLIANCE MODELS SHOWN ON THE FRONT PAGE.

USE ON ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTITUTE A

POTENTIAL FIRE HAZARD.

•Usereplacetoolscarefullytoavoidstrikingtheglass.

•Keepwiremeshscreensclosedduringreplaceuse.

Lower

Pivot Pin

Figure 6

Figure 8

Figure 7

Step 2. Tiltthetopofthedoorintoplaceandcarefullyensurethatthe

upperpivotpinandrollerpinisintheupperdoorguidetrack.

Step 3.Continuetotiltthetopofthedoorintoplaceuntiltheupperpivot

pinengagesthespringclipandthepivotpinlocksintoplace

withintheholeofthespringclip(see Figure 7).

Step 4.Repeatthisprocedurefortheoppositedoorassembly.

IMPORTANT: THE FINISH OF THESE DOORS MAY BE PROTECTED WITH

A SELF ADHERING PLASTIC COATING THAT MUST BE REMOVED BEFORE

HEAT IS GENERATED BY A FIRE IN THE FIREBOX. TO PREVENT MELT-

ING, ENSURE THAT ANY PLASTIC COATING PROTECTING THE FINISH

OF THESE DOORS IS REMOVED FOLLOWING INSTALLATION. REFER TO

THE FIREPLACE INSTALLATION AND CARE AND OPERATION INSTRUC-

TIONS FOR DETAILED INSTRUCTIONS REGARDING THE MAINTENANCE

OF THE FINISH OF THESE DOORS.

CAUTION: THE FRONT-OPEN FIREPLACE OR APPLIANCE SHOULD

ONLY BE OPERATED WITH THE GLASS DOORS FULLY OPEN OR FULLY

CLOSED (SEE FIGURE 8).

CAUTION: GLASS AND METAL FRAMES GET HOT — ALWAYS USE

HANDLES TO OPEN AND CLOSE THE DOORS.

CLEANING

NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT. DO NOT USE

AMMONIA OR ANY AMMONIA BASED GLASS OR HOUSEHOLD CLEANER

TO CLEAN THE GLASS OR THE DOOR FRAME. AN AMMONIA BASED

CLEANER WILL DAMAGE THE FINISH.

Removedirtandgrimefromthedoorsusingacleandampenedtowel

followedbywipingwithadrytowel.Toremovestubbornstainsfromthe

doors,useamildsoapsolutionandtoweltogentlyscrubawaystain.

Takecarenottoscratchtheglasssurface.Donotuseabrasivecleaners.

IMPORTANT: THESE GLASS DOORS UTILIZE TEMPERED GLASS WHICH

IS DESIGNED FOR USE WITH HIGH TEMPERATURES BUT CAN UNEX-

PECTEDLY SHATTER. DO NOT SIT CLOSE TO THE GLASS.

Temperedglasswillbreakintosmallparticlesifitshouldshatterunex-

pectedly.Iftheglassbreaks,particlesofextremelyhotglasscouldbe

dischargedintothesurroundingenvironment,therebycreatingariskof

personalinjuryorre.Observationoftheaboveoperatingprecautions

andinstructionswillreducetheriskofpersonalinjuryorre.

Ifthetemperedglasspanebecomesscratchedorchipped,itcreatesa

weaknessintheglasswhichcancausetheglasstobreakwhenheated.

Replacethepaneofglassbycontactingyournearestdistributorordealer.

P/N 750210M REV. C 04/2014

IHPreservestherighttomakechangesatanytime,withoutnotice, indesign,materials,

specications,pricesandalsotodiscontinuecolors,stylesandproducts.Consultyourlocal

distributorforreplacecodeinformation.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

Astria Fireplaces POLARIS Instruction Sheet

Brand: Astria Fireplaces

Model: POLARIS

Type: Instruction Sheet

This manual is also suitable for

VRE4000

Download PDF

report

Astria Fireplaces POLARIS Instruction Sheet

This manual is also suitable for

Astria Fireplaces POLARIS Instruction Sheet

Related papers

Other documents