Hitachi D10VG - 3/8 Inch Drill 9.0 Amp User manual

English

1

MODEL DRILL

MODÈLE PERCEUSE

MODELO TALADRO

D

10VF

•

D

10VG

D

13VF

•

D

13VG

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner

la mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être

conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual BEFORE operating the power tool. Please keep this

manual available for other users and owners before they use the power tool. This

manual should be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de utilizar la herramienta

eléctrica. Este manual debe ser guardado en un lugar seguro.

D13VF

Page is loading ...

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and

in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

4

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug in any way. Double

Insulation eliminates the need for the three wire grounded power cord and

grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

(3) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from a

receptacle. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

English

5

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear protective glasses. Dust mask, nonskid safety

shoes, hard hat, or ear plugs must be used for appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool's operation. If damaged, have the tool serviced by

a HITACHI authorized service center before using. Many accidents are caused by

poorly maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

with another tool.

5. Service

(1) Tool service must be performed only by a HITACHI authorized service center. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instruction may create a risk of electric shock or injury.

English

6

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear plugs when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. NEVER touch the tool bit with bare hands after operation.

4. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or string,

etc.

5. For D10VF

ALWAYS securely grip the Drill.

For D10VG, D13VF and D13VG

ALWAYS attach the side handle and securely grip the Drill.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

9. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw the

tool. NEVER allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

English

7

13. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and accessories

which have been mounted to the tool should be secure and tight.

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check

for dust build-up frequently.

15. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn out.

16. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

17. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

20. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

21. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Confirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going tos operate here after.

22. Definitions for symbols used on this tool

V ............volts

Hz ..........hertz

A............amperes

no ..........no load speed

W...........watt

...........Class II Construction

---/min ...revolutions per minute

English

8

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation “ means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words

“Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in wet

environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

English

9

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe

operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool

NAME OF PARTS

Fig. 1

Gear Cover

Housing

Drill Chuck

Nameplate

Push Button

Stopper

Switch Trigger

Side Handle

Handle Cover

English

10

Model D13VF D13VG

Speed of Angle Unit

LOW(650/min.) HIGH(1350/min.) LOW(400/min) HIGH(900/min.)

Steel Twist Bit

1/2"(13mm) 1/2"(13mm) 1/2"(13mm) 1/2"(13mm)

Hole Saw

2-1/2"(64mm) 1-1/4"(32mm) 2-3/4"(70mm) 2"(51mm)

Wood Flat Spade Bit

1-1/2"(38mm) 1-1/4"(32mm) 1-1/2"(38mm) 1-1/2"(38mm)

Auger Bit

1-1/2"(38mm) 1-1/8"(29mm) 1-1/2"(38mm) 1-1/4"(32mm)

Self Feed Bit

2-1/4"(57mm) 1-3/4"(44mm) 2-9/16"(65mm) 2-1/8"(54mm)

Hole Saw

4-1/2"(114mm) 2-1/2"(64mm) 4-1/2"(114mm) 4"(102mm)

Model D10VF D10VG D13VF D13VG

Motor Single Phase, Series Commutator Motor

Power Source

Single Phase 120V AC 60 Hz

Current 9.0A

No-Load Speed 0-3000/min. 0-1200/min. 0-850/min. 0-600/min.

Drill Chuck Capacity 3/8" (10mm) 1/2" (13mm)

Electric Brake No No Yes Yes

Capacity Steel Twist Bit

3/8"(10mm) 3/8"(10mm) 1/2"(13mm) 1/2"(13mm)

Hole Saw

— 1-1/2"(38mm) 2"(51mm) 2-3/4"(70mm)

Wood Flat Spade Bit

1"(25mm) 1-1/4"(32mm) 1-1/2"(38mm) 1-1/2"(38mm)

Auger Bit

— — 1-1/4"(32mm) 1-1/2"(38mm)

Self Feed Bit

— — 2-1/8"(54mm)

2-9/16"(65mm)

Hole Saw

1-1/8"(29mm) 2-3/4"(70mm) 4"(102mm)

4-1/2"(114mm)

Weight

with Keyed Chuck

4.0 lbs(1.8kg) 4.2 lbs(1.9kg) 4.6 lbs(2.1kg) 4.6 lbs(2.1kg)

(without

with Keyless Chuck

4.0 lbs(1.8kg) 4.2 lbs(1.9kg) 4.4 lbs(2.0kg) —

cord)

SPECIFICATIONS

English

11

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Boring holes in metal, wood and plastic.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while

the switch is in the ON position, the power tool will start operating immediately and can

cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of sufficient

thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

5. Check your work environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

6. Selecting the appropriate drill bit:

䡬 When boring metal or plastic

Use an ordinary metalworking drill bit.

䡬 When boring wood

Use an ordinary woodworking drill bit.

However, when drilling 1/4" (6.5 mm) or smaller holes, use a metalworking drill bit.

English

12

7. Mounting and dismounting of the bit

For keyed chuck (Fig. 2)

(1) Open the chuck jaws, and insert the bit into

the chuck.

(2) Place the chuck wrench in each of the three

holes in the chuck, and turn it in the clockwise

direction (viewed from the front side). Tighten

securely.

(3) To remove the bit, place the chuck wrench

into one of the holes in the chuck and turn it

in the counterclockwise direction.

(4) If it is hard to loosen the sleeve, fix the

spindle using the open-end wrench, hold the

sleeve firmly, and turn it in the loosening

direction (counterclockwise when viewed

from the front).

For keyless chuck (Fig. 4)

(1) Open the chuck jaws, and insert the bit into

the chuck.

To open the chuck jaws, hold the ring while

turning the sleeve in the counterclockwise

direction (viewed from the front side).

(2) Firmly grasp the ring and turn the sleeve in

the clockwise direction. Tighten securely.

(3) To remove the bit, firmly grasp the ring and

turn the sleeve in the counterclockwise

direction.

8. Installing the side handle (Fig. 5)

A Side handle is supplied with drill. (except

D10VF)

It can be installed on either side of the tool for

right or left handed use.

To install the side handle, thread it into the

socket on the desired side of the tool and

tighten it securely.

9. Check the rotational direction (Fig. 6)

The bit rotates clockwise (viewed from the

rear side) by pushing the R-side of the push

button.

The L-side of the push button is pushed to

turn the bit counterclockwise.

(The

L

and

R

marks are provided on the

body.)

10.Attaching the angle unit. (Optional

accessory for D13VF and D13VG)

(1) Removing chuck from drill (Fig. 7)

Fig. 3

Fig. 2

Fig. 4

Fig. 5

Fig. 6

Drill chuck

Chuck

Wrench

Tighten

Loosen

Sleeve

Ring

Tighten

Loosen

Open End

Wrench

Side Handle

Loosen

Tighten

L

mark

R

mark

Siwtch Trigger

Loosen

English

13

䡬 To remove the chuck from the drill, open the

chuck jaws as far as possible and turn out the

locking screw (left hand thread). This screw

locks the chuck to the spindle. And hold the

drill so that only the chuck rests firmly and

squarely on the edge of a solid bench. Install

the hex. bar wrench into the chuck. Turn the

chuck until the wrench is at about a 30° angle

to the bench top and strike the wrench sharply

with a hammer so the chuck turns in the

counterclockwise direction (viewed from the

front side). This should loosen the chuck

from the spindle which has a right hand

thread and you will be able to remove the

chuck by hand.

CAUTION:

If the chuck cannot be removed by striking

the wrench, don’t strike the wrench forcibly

and send the drill to a HITACHI AUTHORIZED

SERVICE CENTER.

(2) Attaching the angle unit.

䡬 After removing the chuck, engage the

coupling to the drill spindle. Fit the joint

sleeve to the gear cover, attach the angle unit

to the other end of the joint sleeve, and turn

the angle unit slightly in either direction so

the hex. hole in the coupling engages the

hex. portion of the angle unit spindle. Adjust

the direction of the angle unit and tighten the

joint sleeve by clamping bolts.

Tighten two clamping bolts equally and

gradually in turn with a torque of 61-70 In-

lbs. (70-80kg-cm) (extent of force which can

be subjected by only a wrist with the open

end wrench provided to tight clamping bolts.).

(Fig. 8)

䡬 To operate the angle unit at low speed, attach

the chuck to the angle unit spindle at the side

marked “LOW” and secure the locking screw.

At this setting, the drilling speed is decreased

to about 70% and the drilling torque increased

to about 150%. (Fig. 9)

䡬 To operate the angle unit at high speed,

attach the chuck to the angle unit spindle at

the side marked “HIGH” and secure the

locking screw. At this setting, the drilling

speed is increased to about 150% and the

Fig. 8

Fig. 10

Fig. 9

Fig. 7

Hex. Bar

Wrench

Locking Screw

Loosen

Angle

Unit

Joint

Sleeve Coupling

Clamping Bolt

Low Speed

High Speed

English

14

drilling torque decreased to about 70%. (Fig.

10)

(3) Installing the side handle (Fig. 11)

The side handle can be installed on either

side of the angle unit for right or left handed

use. To install the side handle, thread it into

the socket on the desired side of the angle

unit and tighten it securely.

(4) Removing chuck from angle unit (Fig. 12)

䡬 The chuck can be removed from angle unit in

the same manner it was removed from the

drill; however, ALWAYS REMOVE ANGLE

UNIT FROM THE DRILL BEFORE

ATTEMPTING TO LOOSEN CHUCK. This will

prevent damage of drills gear. Use open end

wrench provided to hold angle unit spindle

before attempting to loosen chuck.

CAUTION:

If the chuck cannot be removed by striking

the wrench, don’t strike the wrench forcibly

and send the drill to a HITACHI AUTHORIZED

SERVICE CENTER.

11. Attaching the hook. (Optional

accessory) (Fig. 13)

To attach the hook, it is necessary to

disassemble the handle portion which

covered the tool’s electrical system. For your

continued safety and electrical shock

protection, installing the hook on this drill

should ONLY be performed by a HITACHI

AUTHORIZED SERVICE CENTER.

CAUTION:

When the power tool is used with a hook fixed to it, pay attention to the following points:

䢇 Before hanging the main unit from the waist belt, make sure that the drill has come to

a complete stop.

While it is suspended from the waist belt, the power plug must be disconnected from

the power source.

䢇 Do not walk about with the power tool hanging from the waist belot.

䢇 In the case of operation in a high place, it is dangerous to drop the tool accidentally. If

the hook is deformed or hung from the wrong position, there is danger that the hook will

slip off and the tool will fall.

Be careful to avoid danger.

䢇 In making a through hole, the power tool sometimes shakes violently when the

workpiece is pierced, from example. Be careful you are not hurt by the hook even if such

situation happens.

Fig. 11

Fig. 12

Fig. 13

Side Handle

Open End

Wrench

Hex. Bar Wrench

Hook (A)

English

15

HOW TO USE

CAUTION:

To prevent accidents, make sure to turn the switch off and disconnect the plug from the

receptacle when the drill bits and other various parts are installed or removed. The

power switch should also be turned off during a work break and after work.

1. Switch operation

䡬 When the trigger switch is depressed, the tool rotates. When the trigger is released, the

tool stops.

䡬 The rotational speed of the drill can be controlled by varying the amount that the Trigger

switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as

the trigger switch is pulled more.

䡬 Pulling the trigger and pushing the stopper, it keeps the switched-on condition which is

convenient for continuous running. When switching off, the stopper can be disconnected

by pulling the trigger again.

2. Electric brake (D13VF and D13VG)

When releasing the trigger of the switch, the brake will be applied for immediate

stopping.

CAUTION:

䢇 As there is some reaction when the brake functions, sure to hold the drill securely.

䢇 When the brake becomes ineffective, send the tool to a HITACHI AUTHORIZED SERVICE

CENTRE.

3. Drilling

䡬 When drilling, start the drill slowly, and gradually increasing speed as you drill.

䡬 Always apply pressure in a straight line with the bit. Use enough pressure to keep drilling,

but do not push hard enough to stall the motor or deflect the bit.

䡬 To minimize stalling or breaking through the material, reduce pressure on drill and ease

the bit through the last part of the hole.

䡬 If the drill stalls, release the trigger immediately, remove the bit from the work and start

again. Do not click the trigger on and off in an attempt to start a stalled drill. This can

damage the drill.

䡬 The larger the drill bit diameter, the larger the reactive force on your arm.

Be careful not to lose control of the drill because of this reactive force.

To maintain firm control, establish a good foothold, use side handle, hold the drill tightly

with both hand, and ensure that the drill is vertical to the material being drilled.

English

16

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle

during maintenance and inspection.

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace

the drill bit with a new one or resharpening without delay when abrasion is noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the

screws be loosened, retighten them immediately.

WARNING: Using this drill with loosened screws is extremely dangerous.

3. Keeping after use

When not in use, the Power tool should be kept in a dry place out of the reach of children.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection, carbon brush inspection and

replacement on this tool should ONLY be performed by a HITACHI AUTHORIZED

SERVICE CENTER.

5. Maintenance of the motor

The motor unit winding is the very “heart”’ of the power tool. Exercise due care to ensure

the winding does not become damaged and/or wet with oil or water.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be used,

all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER,

ONLY.

Page is loading ...

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known [to the State of California] to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT:

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou

de toute autre activité de construction renferme des produits chimiques qui sont

connus [par l'Etat de Californie] pour causer des cancers, des défauts de naissance

et autres anomalies de reproduction. Nous énumérons ci-dessus certains de ces

produits chimiques:

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution

de ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler

dans un lieu bien ventilé, et porter un équipement de protection agréé, par exemple

un masque anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Alogunos polvos creados por el lijado mecámico, el aserrado, el esmerilado, el

taladrado y otras actividades de construcción contienen sustancias químicas conocidas

[por le Estado de California] como agentes cancerígenos, defectos congénitos y otros

daños reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza

este tipo de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje

en un lugar bien ventilado y realice el trabajo utilizando el equipamiento apropiado,

tal como las máscares para el polvo especialmente diseñados para eliminar las

partículas minúsculas.

Issued by

Sinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

3950 Steve Reynolds Blvd.

Norcross, GA 30093

itachi Koki Canada Co.

6395 Kestrel Road

Mississauga ON L5T 1Z5

009

Code No. C99104361

Printed in China

Hitachi D10VG - 3/8 Inch Drill 9.0 Amp User manual

This manual is also suitable for

Hitachi D10VG - 3/8 Inch Drill 9.0 Amp User manual

in other languages

Related papers

Other documents