Agri-Fab 45-03431 User manual

Category
Mini tillers
Type
User manual

Agri-Fab 45-03431 is an attachment for sweepers that dethatchers and removes thatch buildup on your lawn. Thatch is a layer of organic matter that can accumulate on the surface of your lawn and prevent water, air, and nutrients from reaching the roots of your grass. Dethatching helps to remove this layer of thatch and promote healthier grass growth.

The Agri-Fab 45-03431 dethatcher is easy to assemble and use, and it features a durable steel frame and powder-coated finish for long-lasting performance. The dethatcher also has a 10-tine design that provides thorough dethatching action, and its adjustable height settings allow you to customize the depth of the dethatching.

Agri-Fab 45-03431 is an attachment for sweepers that dethatchers and removes thatch buildup on your lawn. Thatch is a layer of organic matter that can accumulate on the surface of your lawn and prevent water, air, and nutrients from reaching the roots of your grass. Dethatching helps to remove this layer of thatch and promote healthier grass growth.

The Agri-Fab 45-03431 dethatcher is easy to assemble and use, and it features a durable steel frame and powder-coated finish for long-lasting performance. The dethatcher also has a 10-tine design that provides thorough dethatching action, and its adjustable height settings allow you to customize the depth of the dethatching.

• Safety
• Assembly
• Operation
• Maintenance
• Parts
PRINTEDINU.S.A. FORMNO.42025(05/27/09)
CAUTION:
ReadRulesfor
SafeOperation
andInstructions
Carefully
DETHATCHER
FOR SWEEPERS
OWNERS
MANUAL
Model No.
45-03431
the fastest way to purchase parts
www.speedepart.com
2
SAFETY RULES
Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.
Exercisecautionatalltimes,whenusingpowerequipment.
Readthisownersmanualcarefullyforoperatingandserviceinstructionsbeforeattemptingtoassembleoroperatethe•
dethatcher.Bethoroughlyfamiliarwiththeproperuseofthedethatcher.
Readthevehicleownersmanualandvehiclesafetyrules,andknowhowtooperatethevehiclebeforeusingthe•
dethatcher.
Readthelawnsweeperownersmanualandsafetyrules,andknowhowtooperatethelawnsweeperbeforeusingthe•
dethatcher.
Neverallowchildrentooperatethetractorordethatcherattachment,anddonotallowadultstooperatewithoutproper•
instructions.
Thisdethatcherattachmenthassharptinepoints.Alwayshandlewithcareandwearsubstantialfootwearwhen•
operatingthisdethatcher.
Donotallowanyonetorideorsitonthedethatcher,lawnsweeperortowingvehicle.•
Keeptheareaofoperationclearofallpersons,particularlysmallchildren,andalsopets.•
Alwaysbeginwiththetransmissioninrst(low)gearandengineatlowspeed,andgraduallyincreasespeedas•
conditionspermit.
Vehiclebrakingandstabilitymaybeaffectedwiththeattachmentofthisequipment.Beawareofchangingconditions•
onslopes.Refertosafetyrulesinthevehicleowner'smanualconcerningsafeoperationonslopes.STAY OFF OF
STEEP SLOPES.
Alwaysoperateupanddownaslope,neveracrossthefaceofaslope•
Thisequipmentshouldbeoperatedatreducedspeedonroughterrain,alongcreeksandditchesandonhillsides,to•
preventtippingandlossofcontrol. Donotdrivetooclosetoacreekoraditch.
Followthemaintenanceinstructionsasoutlinedinthisownersmanual.•
LOOKFORTHISSYMBOLTOPOINTOUTIMPORTANTSAFETYPRECAUTIONS.
ITMEANS—ATTENTION!BECOMEALERT!YOURSAFETYISINVOLVED.
1
2
3
4
CARTON CONTENTS
REF. PART NO. QTY. DESCRIPTION
1 64650 1 SpringMountFrameAssem.
2 46761 7 SpringTine
REF. PART NO. QTY. DESCRIPTION
3 48098 1 GaugeWheel
4 26624 2 MountBracket
3
5
19
NOT SHOWN FULL SIZE
6 7
18
9
10
11
8
13
14
15
16
21
22
24
23
20
17
12
HARDWARE PACKAGE - FULL SIZE
REF. PART NO. QTY. DESCRIPTION
5 46526 3 HexBolt,1/2-13x3-1/2"
6 44292 2 HexBolt,5/16-18x2-1/2"
7 43085 7 HexBolt,5/16-18x1-1/2"
8 48813 2 U-Bolt,1/4-20
9 48811 1 Hook,Transport
10 43081 2 Washer,5/16"
11 R19171616 2 Washer,1/2"
12 43070 14 Washer,3/8"
13 43055 2 HairCotterPin,3/32"
14 47189 4 NylockNut,1/4-20
REF. PART NO. QTY. DESCRIPTION
15 47810 9 NylockNut,5/16-18
16 43019 1 JamNut,Plain1/2-13
17 48115 3 JamNut,Nylock1/2-13
18 48812 2 ClevisPin,5/16"x1-3/8"
19 44481 2 VinylCap
20 48917 2 Clamp
21 25054 2 Bracket,U-BoltClamp
22 46499 2 Spacer,.8x1x2.55"
23 741-0248 4 FlangeBearing
24 42212 1 SMARTSweepHook
4
FIGURE 1
FIGURE 2
1/2" x 3-1/2" HEX BOLT
1/2" WASHER
1/2" NYLOCK
JAM NUT
Use this hole for
42" & 46" sweepers
Use this hole for
smaller sweepers and
SMARTSweepers
1/2" JAM NUT
ASSEMBLY (ALL MODELS) ASSEMBLY (NON-SMARTSWEEP MODELS)
5/16" NYLOCK NUT
3/8" WASHER
5/16" x 1-1/2"
HEX BOLT
VINYL CAP
Assemblesevenspringtinestothetopoftheframe1.
tube.Usea5/16"x1-1/2"hexbolt,two3/8"at
washersanda5/16"nylocknutforeachspringtine.
Placeone3/8"atwasherontopoftheframetube
andthesecond3/8"atwasherontopofthespring
tine.Seegure1.
NOTE:Onsweeperssmallerthan42",useonlyvespring
tines.
Assembleavinylcapontoeachendoftheframe2.
tube.Seegure1.
Assemblea1/2"washer,thewheel,another1/2"3.
washeranda1/2"plainjamnutontothe1/2"x3-1/2"
hexbolt.Seegure2.
Inserttheboltthroughtheweldedbracketand4.
assemblea1/2"nylockjamnutontothebolt.Adjust
nutssothatthereisnoendplayinthewheeland
thentightensecurelyagainsttheweldedbracket.
Makesurethewheelstillturnsfreely.Seegure2.
CONDUIT
CLAMP
TRANSPORT
HOOK
FIGURE 3
FIGURE 4
3/32" HAIR
COTTER PIN
5/16" WASHER
5/16" x 1-3/8"
CLEVIS PIN
HEIGHT ADJUSTMENT
MIDDLE SETTING
Assembleaconduitclampontoeachendofthe1.
sweeperheightadjustmenttubesothatthestraight
partoftheclampisontopofthetube.Seegure3.
Removethehitchbracketsandthebolts,ifpresent,2.
fromtheendsofthesweeper'shitchtubes.Slidethe
transporthookontotheL.H.hitchtubeasshownin
gure3.
Reassemblethehitchbracketsandboltstothehitch3.
tubes.Refertoyoursweeperowner'smanual.
Connectthesweepertothetractor.Setthesweeper4.
heightadjustmenthandletoaboutthemiddleofit's
adjustmentrange.
Placethedethatcherinfrontofthesweeperhousing,5.
underneaththehitchtubes.
Connectthedethatchertotheconduitclampusing6.
two5/16"x1-3/8"clevispins,5/16"washersand
3/32"haircotterpins.Seegure4.
5
FIGURE 5
KEEPER BRACKET
U-BOLT
1/4" NYLOCK NUT
FIGURE 6
FIGURE 7
FIGURE 8
If you have a 30" sweeper, skip steps 7 through 9.
Makesurethesweeperheightadjustmenthandleis7.
stillsettoaboutthemiddleofit'sadjustmentrange.
Centerthedethatcherwiththesweeper.8.
Assemblethekeeperbrackets(bendtotheinside)9.
tothesweeper'shitchtube,outsideoftheconduit
clamps.Useau-boltandtwo1/4"nylocknuts
perbracket.Positionthekeeperbracketsagainst
thesidesoftheconduitclamps,approximately
perpendiculartotheground.Tightenthenylocknuts
withoutbendingthekeeperbrackets.Seegure5.
Liftthefrontofthedethatcherandsecureitin10.
transportpositionusingthetransporthook.See
gure6.
Assemblethefourbearingstothetwo.8x1x2.55"1.
spacersandthenslideeachthroughaclamp.See
gure7.
ASSEMBLY (SMARTSWEEP MODELS)
BEARING
BEARING
.8 x 1 x 2.55"
SPACER
CLAMP
1/2 x 3-1/2" HEX BOLT
1/2" NYLOCK
JAM NUT
Attacheachofthebearing,spacer,andclamp2.
assembliestoamountbracketusinga1/2x3-1/2"hex
boltand1/2"nylockjamnut.Seegure8.
NOTE:ThedethatcherattachestotheSMARTSweep
offsettube.Thispreventsyoufromoffsettingthesweeper.
6
OPERATION
RAISING/LOWERING THE DETHATCHER
Toraisethedethatcherfortransport,liftuponthe1.
frontofthedethatcherandsecureitwiththetransport
orSMARTSweephook.Lowerthedethatcherby
releasingthehook.
SETTING THE OPERATING POSITION
Theoperatingheightofthedethatcheriscontrolled1.
bythegaugewheelatthefrontofthedethatcher
andisnotadjustable.Thecorrectwheelposition
wasdeterminedingure2whenyouassembledthe
wheel.
Setthesweepertothedesiredoperatingheight.(The2.
bestheightisusuallywiththebrushessetabout1/2"
downintothegrass.)Refertoyoursweeperowner's
manualforsweeper.
USING THE DETHATCHER
Regularremovalofthatchiscriticaltothemaintenanceof
ahealthylawn.Thatchislayerofstems,clippings,runners,
rootsandleavesthathavenotdecayed.Excessivethatch
prevents air, waterandfertilizerfromreachingtheroots.
The dethatcher will effectively dislodge excessive thatch
fromyourlawn.
Startwiththetractorinlowgear.Varytheforward1.
speedtodeterminethebestspeedformaximum
dethatcherperformance.
Useacrisscrosspatterntoachievethemosteven2.
removalofthatch.
Onslopes,alwaysoperateinanupanddown3.
directiononly.
Avoidextremelysharpturns.4.
Avoidtowingthedethatcheracrosssuddensteep5.
dipsinthegroundwhiledethatching.Lossofground
contactwiththegaugewheelcouldcausethe
dethatchertobepulledbackunderneaththesweeper.
MAINTENANCE
Beforeeachuse,checkallnutsandboltsfor1.
tightness.
Cleanaftereachusetohelppreventrust.2.
Ifrustappearsonthespringtines,sandlightlyand3.
coatwithenamelpaint.
STORAGE
Alwaysstoreinadryarea,andcoatexposedmetal1.
withlightoilwhennotinuse.
3/32" HAIR
COTTER PIN
5/16" WASHER
5/16 x 1-3/8"
CLEVIS PIN
5/16" NYLOCK NUT
5/16" x 2-1/2"
HEX BOLT
FIGURE 9
FIGURE 10
FIGURE 10
Fasteneachclamptothespringmountframe3.
assemblyusingone5/16x1-3/8"clevispin,5/16"
washer,and3/32"haircotterpin.
Securethetwomountbracketstotheinnerholesof4.
thedrawbaroffsettubeofthesweeperusingtwo5/16
x2-1/2"hexboltsand5/16"nylocknuts.Seegure10.
SlidetheSMARTSweephookontothesweeperhitch.5.
Liftupthefrontofthedethatcherandslideitintothe
twobottomhookstosecureitinthetransportposition.
SMARTSWEEP HOOK
REPAIR PARTS FOR MODEL 45-03431 DETHATCHER FOR SWEEPERS
8
6
15
5
17
22
4
18
10
13
23
23
20
21
14
19
19
5
11
11
16
17
1
15
24
12
12
18
10
13
20
7
2
3
9
REF. PART NO. QTY. DESCRIPTION
1 64650 1 SpringMountFrameAssem.
2 46761 7 SpringTine
3 48098 1 GaugeWheel
4 26624 2 MountBracket
5 46526 3 HexBolt,1/2-13x3-1/2"
6 44292 2 HexBolt,5/16-18x2-1/2"
7 43085 7 HexBolt,5/16-18x1-1/2"
8 48813 2 U-Bolt,1/4-20
9 48811 1 Hook,Transport
10 43081 2 Washer,5/16"
11 R19171616 2 Washer,1/2"
12 43070 14 Washer,3/8"
13 43055 2 HairCotterPin,3/32"
REF. PART NO. QTY. DESCRIPTION
14 47189 4 NylockNut,1/4-20
15 47810 9 NylockNut,5/16-18
16 43019 1 JamNut,Plain1/2-13
17 48115 3 JamNut,Nylock1/2-13
18 48812 2 ClevisPin,5/16"x1-3/8"
19 44481 2 VinylCap
20 48917 2 Clamp
21 25054 2 Bracket,U-BoltClamp
22 46499 2 Spacer,.8x1x2.55"
23 741-0248 4 FlangeBearing
24 42212 1 SMARTSweepHook
42025 1 Owner'sManual
REPAIR PARTS
Agri-Fab,Inc.
303WestRaymond
Sullivan,IL.61951
217-728-8388
www.agri-fab.com
the fastest way to purchase parts
www.speedepart.com
©2003Agri-Fab,Inc.
Thisdocument(ormanual)isprotectedundertheU.S.CopyrightLawsandthecopyrightlawsofforeigncountries,
pursuanttotheUniversalCopyrightConventionandtheBerneconvention.Nopartofthisdocumentmaybereproduced
ortransmittedinanyformorbyanymeans,electronicormechanical,includingphotocopyingorrecording,orbyany
informationstorageorretrievalsystem,withouttheexpresswrittenpermissionofAgri-Fab,Inc.Unauthorizedusesand/or
reproductionsofthismanualwillsubjectsuchunauthorizedusertocivilandcriminalpenaltiesasprovidedbytheUnited
StatesCopyrightLaws.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Agri-Fab 45-03431 User manual

Category
Mini tillers
Type
User manual

Agri-Fab 45-03431 is an attachment for sweepers that dethatchers and removes thatch buildup on your lawn. Thatch is a layer of organic matter that can accumulate on the surface of your lawn and prevent water, air, and nutrients from reaching the roots of your grass. Dethatching helps to remove this layer of thatch and promote healthier grass growth.

The Agri-Fab 45-03431 dethatcher is easy to assemble and use, and it features a durable steel frame and powder-coated finish for long-lasting performance. The dethatcher also has a 10-tine design that provides thorough dethatching action, and its adjustable height settings allow you to customize the depth of the dethatching.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI