Craftsman 486.24316 User manual

Craftsman
Brand
Craftsman
Model
486.24316
Category
Mini tillers
Type
User manual

This manual is also suitable for

40" TINE DETHATCHER
Model No. 486.243152
Model No. 486.24316
Owner's Manual
CAUTION:
Before using this product, read
this manual and follow all Safety
Rules and Operating Instructions.
• Safety
• Assembly
• Operation
• Maintenance
• Parts
PRINTEDINU.S.A.
FORMNO.42107(8/14/08)
Sears,RoebuckandCo.,HoffmanEstates,IL60179U.S.A.
www.sears.com/craftsman
®
STOP
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
2
TABLE OF CONTENTS
WARRANTY
ONE YEAR FULL WARRANTY
Whenoperatedandmaintainedaccordingtotheinstructionssuppliedwithit,ifthisTineDethatcherfailsduetoadefectin
materialorworkmanshipwithinoneyearfromthedateofpurchase,call1-800-4-MY-HOME®toarrangeforfreerepair(or
replacementifrepairprovesimpossible).
Ifthisproductisusedforcommercialorrentalpurposes,thiswarrantyappliesforonly90daysfromthedateofpurchase.
Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.
Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179
SAFETYRULES ..........................................................2
FULLSIZEHARDWARECHART ................................3
CARTONCONTENTS ................................................. 4
ASSEMBLY ..................................................................4
OPERATION ................................................................6
MAINTENANCE/STORAGE ........................................ 6
REPAIRPARTS .........................................................7
PARTSORDERING/SERVICE ....................BackCover
Lookforthissymbolto pointoutimportantsafetyprecautions. Itmeans—Attention!!
Become alert!! Your safety is involved.
• Alwaysbeginwiththetransmissioninrst(low)gear
and engine at low speed, and gradually increase
speed as conditions permit.
• Thevehiclebrakingandstabilitymaybeaffected
with the attachment of this equipment. Be aware of
changing conditions on slopes. Refer to safety rules in
the vehicle owner's manual concerning safe operation
on slopes. STAY OFF OF STEEP SLOPES.
• Alwaysoperateupanddownaslope,neveracross
the face of a slope
• Thisequipmentshouldbeoperatedatreducedspeed
onroughterrain,alongcreeksandditchesandon
hillsides, to prevent tipping and loss of control. Donot
drivetooclosetoacreekoraditch.
• Donottowthisequipmentonahighwayoranyother
publicthoroughfare.
• Followthemaintenanceinstructionsasoutlinedinthis
owners manual.
• Readthisownersmanualcarefullyforoperatingand
serviceinstructionsbeforeattemptingtoassembleor
operate this equipment. Be thoroughly familiar with
the proper use of this equipment.
• Readthevehicleownersmanualandvehiclesafety
rules,andknowhowtooperatethevehiclebefore
using this equipment.
• Neverallowchildrentooperatethetractoror
dethatcher attachment, and do not allow adults to
operate without proper instructions.
• Thisdethatcherattachmenthassharptinepoints.
Alwayshandlewithcareandwearsubstantialfoot
wear when operating this dethatcher.
• Donotallowanyonetorideorsitondethatcher
attachment frame or on towing vehicle.
• Keeptheareaofoperationclearofallpersons,
particularly small children, and also pets.
Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.
Exercisecautionatalltimeswhenusingpowerequipment.
SAFETY
SERIALNUMBER: __________________
DATEOFPURCHASE: __________________
Themodelnumberandserialnumberswillbefoundona
decal attached to the dethatcher.
Youshouldrecordboththeserialnumberandthedateof
purchaseandkeepinasafeplaceforfuturereference.
3
HARDWARE PACKAGE CONTENTS
SHOWN FULL SIZE
NOT SHOWN FULL SIZE
Ref. Qty. Description
A 2 ShoulderBolt
B 2 HexBolt,5/16"x2"Lg.
C 2 HexBolt,5/16"x1-1/4"Lg.
D 11 HexBolt,5/16"x1"Lg.
E 4 CarriageBolt,5/16"x1"
F 1 HairCotterPin,1/8"
G 1 HitchPin,3/8"
Ref. Qty. Description
H 19 NylockNut,5/16"
I 2 NylockNut,3/8"
J 4 AngleBracket
K 1 Grip
A B C D E
F
G
K
H
I
J
4
ASSEMBLY
FIGURE 2
FIGURE 1
• Fastenthehitchmountarmstotheoutsideofthefront
anglebrackets.Usetwo5/16"x1"hexboltsand5/16"
nylocknuts.Tighten, then loosen the nuts slightly.
Seegure2.
• Fastenthehitchmountarmstotheoutsideoftherear
hitcharmmountbrackets.Usetwo5/16"x1"carriage
boltsand5/16"nylocknuts.Do not tighten yet. See
gure2.
CARTON CONTENTS
REMOVAL OF PARTS FROM CARTON
• Removeallpartsandhardwarepackagesfromthe
carton.Layoutallpartsandhardwareandidentify
usingtheillustrationsonpages3and4.
TOOLS REQUIRED FOR ASSEMBLY
(2)1/2"wrenches
(1)9/16"wrench
(1)3/4"wrenchoradjustablewrench
(1)Pliers
1. HitchMountArms(2)
2. LiftHandle
3. HitchBrackets(2)
4. AxleBracket
5. HitchArmMountBrackets(3)
6. Wheels(2)
7. TineShieldAssembly
2
4
6
1
5
3
7
5/16" x 1"
CARRIAGE BOLT
5/16"
NYLOCK
NUT
5/16" x 1"
HEX BOLT
5/16"
NYLOCK
NUT
HITCH ARM
MOUNT BRACKET
ANGLE
BRACKET
5/16" x 1"
HEX BOLT
5/16" NYLOCK
NUT
ANGLE
BRACKET
• Assembletwo(tall)hitcharmmountbracketsandtwo
(short)anglebracketstothebottomofthetineshield
attherear.Usefour5/16"x1"hexboltsand5/16"
nylocknuts.Do not tighten yet.Positionthebrackets
asshowningure1.
• Assembletwoanglebracketstothebottomofthetine
shieldatthefront.Usetwo5/16"x1"hexboltsand
5/16"nylocknuts.Do not tighten yet.Positionthe
bracketsasshowningure1.
5
• Assemblethefrontendsofthehitchmountarms
togetherusingtwo5/16"x1-1/4"hexboltsand5/16"
nylocknuts.Do not tighten yet. Seegure3.
• Assemblethehitchbracketstothetopandbottomof
thehitchmountarmsusingtwo5/16"x2"hexbolts
and5/16"nylocknuts.Do not tighten yet. Seegure
3.
• Assemblethe3/8"hitchpinthroughthehitchbrackets
andsecureitwitha1/8"haircotterpin.Seegure3.
• Tightentheboltsandnutsassembledingure3.
Tightentheboltsandnutsassembledingure1.
Tightentherearboltsandnutsassembledingure2.
FIGURE 4
• Assembletheaxlebrackettotheoutsideoftherear
anglebracketsusingtwo5/16"x1"hexboltsand
5/16"nylocknuts.Theangledendsoftheaxlebracket
mustpointasshowningure4.Tightentheboltsand
nuts and then loosen slightly.
• Assemblethewheelstotheaxlebracketusingtwo
shoulderboltsandtwo3/8"nylocknuts.Tighten. See
gure5.
FIGURE 6
• Assembleahitcharmmountbrackettotheaxle
bracketusingtwo5/16"x1"carriageboltsand5/16"
nylocknuts.Do not tighten yet.Seegure6.
• Insertthelifthandledownthroughthetineshield.
Attachittothejustassembledhitcharmmount
bracketusinga5/16"x1"hexboltanda5/16"nylock
nut. Tighten.Seegure6.
• Positionthehitcharmmountbracketsothatthereis
sidetensiononthelifthandlewhenitislockedinthe
up position. Tightenthenuts.Seegure6.
• Assemblethegripontotheendofthelifthandle.See
gure6.
FIGURE 5
FIGURE 3
5/16" NYLOCK NUT
1/8" HAIR
COTTER PIN
5/16" x 1-1/4"
HEX BOLT
5/16" x 2"
HEX BOLT
3/8" HITCH PIN
HITCH
BRACKET
5/16" NYLOCK NUT
5/16" x 1"
HEX BOLT
AXLE BRACKET
3/8" NYLOCK NUT
SHOULDER BOLT
6
OPERATION
MAINTENANCE/STORAGE
ServiceDates
Checkforloosefasteners X
Lubrication X
MAINTENANCESCHEDULE
Fill in dates as you
complete regular service.
Before each use
Aftereachuse
Everyseason
Before storage
CUSTOMER RESPONSIBILITIES
• Readandfollowthemaintenancescheduleandthemaintenanceprocedureslistedinthissection.
• Beforeeachusecheckallnutsandboltsfortightness.
• Lubricatewheelsatleastonceayearorasneeded.
• Ifrustappearsontheshieldorspringtines,sand
lightly and coat with enamel paint.
• Alwaysstoreinadryarea,andcoatexposedmetal
with light oil when not in use.
Regular removal of thatch is critical to maintenance of a
healthylawn.Excessivethatchpreventsair,waterand
fertilizerfromreachingtheroots.Toeffectivelydislodge
excessivethatchfromyourlawn,readtheseinstructions
forproperadjustmentandoperationofthedethatcher.
ADJUSTMENT OF TINE SHIELD
• Movethetowingvehicleontoalevelsurface,such
asadrivewayorgarageoorandattachthetine
dethatchertothevehiclehitch.Seegure7.
• Lowerthedethatcherintooperatingpositionusingthe
lifthandle.Loosenthetwonylocknutsandcarriage
boltswhichfastenthehitchmountarmstothehitch
armmountbracketsattherearofthetineshield.
Adjustthetineshielduntilitislevelandboththefront
and rear spring tines are in contact with the ground.
Retightenthehexnuts.Seegure7.
FIGURE 7
FIGURE 8
OPERATING TIPS
• Varythevehicle'sforwardspeeduntilthebest
dethatching action is achieved.
• Forbestresults,useacrisscrosspatternonyour
lawn.
• Ifthedethatcherappearstobe"jumping"during
use,thenextraweightshouldbeaddedtothetine
shield.Inmostconditionsextraweightwillbeneeded.
Concretepatioblocksarerecommendedforweight
becauseoftheirlowprole;howeveranytypeof
weightissuitableifitcanbetieddowntotheshield.
Secureweightbyusingsuitablebindingmaterialsuch
asrubbertiedownstrapsorwire,fasteningtothe
holesintheshieldange.Seegure8.
HITCH
MOUNT
ARMS
CARRIAGE BOLT
& NYLOCK NUT
• Toremoveaspringtine,insertascrewdriveror
punchintothelockingtabandpryup.Replacespring
tineandprytabdown.Seegure9.
FIGURE 9
SCREW
DRIVER
7
*PurchaseCommonHardwareLocally
REF. PART QTY. DESCRIPTION
NO. NO.
1 23442 3 HitchArmMountBracket
2 23981 2 HitchBracket
3 43783 10 SpringTine
4 47633 2 SpringAlignmentWire
5 43021 2 Wheel
6 24836 1 TineShield
7 23914 2 HitchMountArm
8 24594 1 LiftPlate
9 24595 1 AxleBracket
10 24596 1 LiftHandle
11 43029 2 ShoulderBolt
12 23826 4 AngleBracket
REF. PART QTY. DESCRIPTION
NO. NO.
13 HA21362 2 NylockNut,3/8-16
14 43840 2 HexBolt,5/16-18x1-1/4"
15 43063 15 HexBolt,5/16-18x1"
16 47810 23 NylockNut,5/16-18
17 44326 4 CarriageBolt,5/16-18x1"
18 43943 1 HandleGrip
19 44180 2 HexBolt,5/16-18x2"
20 47623 1 HitchPin,3/8"(FlatHead)
21 43343 1 HairCotterPin,1/8"
42107 1 Owner'sManual
PARTS
40" TINE DETHATCHER MODELS 486.243152, 486.24316
7
7
19
14
2
2
20
21
16
16
16
16
12
12
12
12
1
1
9
1
17
15
15
15
16
16
16
16
16
16
15
15
15
15
17
8
6
16
3
4
4
11
11
10
18
5
5
13
13
® Registered Trademark /
TM
Trademark /
SM
Service Mark of Sears Brands, LLC
® Marca Registrada /
TM
Marca de Fábrica /
SM
Marca de Servicio de Sears Brands, LLC
MC
Marque de commerce /
MD
Marque déposée de Sears Brands, LLC © Sears Brands, LLC
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
®
(1-888-784-6427)
Au Canada pour service en français:
1-800-LE-FOYER
MC
(1-800-533-6937)
www.sears.ca
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Craftsman 486.24316 User manual

Craftsman
Brand
Craftsman
Model
486.24316
Category
Mini tillers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents