SUPERTHIN
™
SMALL PIVOT MOUNT
SECURE, EASY TO INSTALL, LOWPROFILE MOUNT WITH ADJUSTABLE PIVOT
INSTALLATION MANUAL
AND WARRANTY
40
lbs.
(18.14 kg)
10
"
-32
"
(25-81cm)
2
This SuperThin mount is designed to mount 10"– 32"
(25 – 81 cm) atscreen televisions to vertical walls.
Maximum weight capacity is 40 lbs. (18.14 kg).
SUPERTHIN
™
SMALL PIVOT MOUNT
Before installing, carefully review the instructions
to ensure that no parts are missing or defective.
Improper installation can cause damage or serious
injury. Do not use this product for any purpose not
explicitly specied by Monster or the manufacturer.
Neither Monster nor the manufacturer can be liable
for damage or injury caused by incorrect assembly,
incorrect mounting or incorrect use.
All hardware is supplied for the following wall
conditions: Wood stud, brick, solid concrete and
concrete block.
Note: The supplied hardware is not for steel stud
walls. If you are uncertain about the nature of your
wall construction, consult an installation contractor.
SAFETY WARNING
If you don’t understand these directions, or are
unsure of how to install this product installation,
please call a qualied contractor or contact Monster
Cable Products, Inc.
If you bought the Product in the United States, Latin
America (Mexico 011-882-800-8989), or Asia Pacic
(China 400-820-8973), contact Monster, LLC (455
Valley Drive, Brisbane, CA 94005) at 1 877 800-8989.
If you bought the Product anywhere else, contact
Monster Technology International Ltd., Ballymaley
Business Park, Ennis, Co. Clare, Ireland. You can write
or use one of the following telephone numbers:
Canada 866-348-4171, Ireland 353 65 68 69 354,
Austria 0800296482, Belgium 0800-79201, Czech
Republic 800-142471, Denmark 8088-2128, Finland
800-112768, France 0800-918201, Germany
0800-1819388, Greece 00800-353-12008, Italy
800-871-479, Netherlands 0800-0228919, Norway
800-10906, Russia 810-800-20051353, Spain
900-982-909, Sweden 020-792650, Switzerland
0800834659, United Kingdom 0800-0569520.
Important Notice
Monster intends to make this manual accurate and
complete, however, Monster makes no claim that
the information contained herein covers all details,
conditions or variations, nor does it provide for
every possible contingency in connection with the
installation or use of this product. The information
contained in this document is subject to change
without notice or obligation of any kind. Monster
makes no representation of warranty, expressed
or implied, regarding the information contained
herein. Monster assumes no responsibility for
accuracy, completeness or suciency of the
information contained in this document.
3
7.09" (18.0cm)7.09" (18.0cm)
13.54" (34.4cm)
3.94" (10.0cm)
7.87" (20.0cm)
10.24" (26.0cm)
2.95" (7.5cm)
7.09" (18.0cm)
10.24" (26.0cm)
8.0" (20.3cm)
6.98" (17.5cm)
1.00" (25.5cm)
Specifications and Notes
VESA
™
75×75 / 100×100 / 200×100 / 200×200 / Compliant
Monster is constantly striving to improve its products. Specications are subject to change without notice.
4
Package Contents
If any parts are missing, please call the appropriate Monster number for your location.
See page 2 for phone numbers.
1 TV Mounting Plate
2 Allen Keys
4 Rectangular
Washers
1 Cardboard
Installation Template
2 Concrete Anchors 2 Lag Bolts 2 Round Washers
Screws
4 each M4×10 / M4×15 / M4×25
4 each M5×10 / M5×15 / M5×25
4 each M6×10 / M6×15 / M6×25
1 Wall Mounting Plate
with Pivot Arm
1 Electronic
Studnder
1 Bubble Level
5
WARNINGS
A WARNING alerts you to the possibility of serious
injury or death if you do not follow the instructions.
(1) DO NOT install on a sloping surface. Install
exclusively on a vertical surface.
(2) DO NOT mount to cabinetry made of
particleboard.
(3) DO NOT install in a room with excessively high
temperatures or high humidity. Install at least 3 ft.
from all water sources. Refer to TV manufacturer’s
manual for specic information regarding
temperature and humidity.
(4) DO NOT install near an air conditioner.
(5) DO NOT install in a location where there is
excessive dust, smoke or moisture. These sources
can create a re.
(6) NEVER apply unnecessary stress or load on the
installed unit. Never hang on the unit.
(7) DO NOT install unit alone. Safe installation
requires at least two people.
(8) DO NOT route your atscreen TV’s power cord
in wall. Check local building/electrical codes for
more information.
(9) DO NOT over tighten screws or bolts. This can
damage the wall plate or the surface of your wall.
Thread screws or bolts carefully by hand before
tightening. If you feel any resistance, remove the
screw or bolt immediately.
(10) DO NOT release the wall plate until you are
absolutely sure it is secured to the wall.
Important!
Read Before Installing
CAUTIONS
A CAUTION alerts you the possibility of damage or
destruction of equipment if you do not follow the
corresponding instruction.
(1) To prevent eye fatigue, do not install where there
is direct sunlight or excessive light.
(2) When carrying out maintenance, disconnect the
TV’s power supply to avoid electrical shock.
(3) If planning to route AV cable in wall, only use
cable that is approved for this use.
Masonry Mounting
While masonry materials (bolts and concrete
anchors) are included, masonry mounting requires
specialized knowledge, skills and tools. Monster
highly recommends that you seek the assistance of
a professional installer when mounting to masonry.
DO NOT drill holes in masonry mortar joints.
6
Pre-Installation Checklist
For wood stud mounting, your mounting
location must have at least one wall stud.
Your view of the mounting location must be
free of glare or other obstructions.
Your mounting location must be near an AC
power outlet. Ideally the outlet should be
behind your TV. This allows you to conceal your
display’s power cord.
Your mounting location must be at least 3 ft.
from any source of heat or water.
Your mounting location must allow enough
room for your TV to swing completely to the
left and right on the pivot mount. Refer to
Specications on page 3.
TIP: To hide your TV’s power cord and AV cables,
install a Monster FlatScreen
™
CleanView
™
Cable
Manager.
IMPORTANT NOTE
Due to the design of the Monster FlatScreen Small
Pivot Mount, the center of your TV will only be
aligned on the center of the wall plate when the
mount is fully extended; otherwise it will be oset
to the right or left up to 7” (180mm) when at to
the wall.
Required Tools
Wall Stud Mounting
Level (included)
Electronic studnder (included)
Electric hand drill
³
" drill bit
Phillips screwdriver
Wrench or socket set
Masking tape
Masonry Mounting
(brick, concrete, concrete blocks)
Above tools
Replace
³
" drill bit with ½" masonry drill bit
Hammer
7
1
Locate a wall stud at your desired mounting
location.
2
Position the supplied cardboard template
over the stud and tape template to wall with
masking tape. Make sure the template is level by
using the supplied bubble level.
Wood Stud Mounting
An electronic studfinder is included. Remove
plastic tab on the back of the studfinder to activate
battery. To locate a wall stud, hold the studfinder
against the wall where you want to mount your TV.
Push down the button on the studfinder and slide
the studfinder along the wall until the indicator
light goes on.
Installing the Wall Mounting Plate
Remove all pieces of the wall mounting system to
ensure you have all necessary parts.
8
Wood Stud Mounting (cont’d)
4
Position the wall mounting plate over the holes
drilled in the wall stud.
3
With your electric drill and
³
" bit, pre-drill
a 3" deep hole where indicated on template.
After drilling holes, remove template from wall.
5
Make sure the wall plate is level by using the
supplied bubble level. Place the provided
level on the wall plate and confirm that the wall
plate is horizontally straight. Hold the plate firmly
in place.
9
Wood Stud Mounting (cont’d)
6
With the help of another person, attach the
wall plate to the wall using the lag bolts and
round washers as shown to the right. Tighten each
bolt with your wrench. Turn clockwise until secure.
Continue to page 13 to continue your installation.
DO NOT over tighten bolts. This can
damage the wall plate or the surface
of your wall.
DO NOT release the wall plate until
you are absolutely sure it is secured
to the wall.
10
Masonry Mounting
Masonry mounting requires specialized knowledge,
skills and tools. Monster highly recommends that
you seek the help of a professional installer when
mounting to masonry.
1
Position the supplied cardboard template in
the desired location and tape template to wall
with masking tape. Make sure the template is level
by using the supplied bubble level.
2
With your electric drill and ½" masonry bit,
pre-drill a 3" deep hole where indicated by
template. Be careful not to drill into a mortar joint.
After drilling holes, remove template from wall.
DO NOT drill holes in masonry
mortar joints.
11
Masonry Mounting (cont’d)
4
Position the wall mounting plate over the holes
drilled in the wall.
3
Install the supplied plastic concrete anchors
in each hole. Tap into hole with hammer until
fully seated.
5
Make sure the wall plate is level by using the
supplied bubble level. Place the provided
level on the wall plate and confirm that the wall
plate is horizontally straight. Hold the plate firmly
in place.
12
Masonry Mounting (cont’d)
6
With the help of another person, attach the
wall plate to the wall using the lag bolts and
round washers as shown to the right. Tighten each
bolt with your wrench. Turn clockwise until secure.
DO NOT over tighten bolts. This can
damage the wall plate or the surface
of your wall.
DO NOT release the wall plate until
you are absolutely sure it is secured
to the wall.
13
Detaching TV Mounting Plate from Pivot Arm
3
Detach TV mounting plate by pulling up and
out from pivot arm.
2
Remove bolt and pivot washer.
This mount comes preassembled in the package.
Before attaching your flatscreen TV to the TV
mounting plate it is necessary to detach the TV
mounting plate from the pivot arm.
1
Using supplied Allen key, loosen locking bolt
on top of pivot arm.
14
Attaching Your Flatscreen TV
to the TV Mounting Plate
1
Locate the threaded inserts on your TV’s
back panel.
2
Place the TV mounting plate against the back
of your TV to determine which set of holes
aligns perfectly with the four threaded inserts on
your TV’s back panel.
Your mounting system features 9 sets of screws of
varying diameter and length. Before attaching the
TV mounting plate to your display, determine which
screw set is correct for your display.
3
By hand, thread the screws through the
rectangular washers and the mounting plate’s
mounting holes into the four TV inserts.
4
With a Phillips screwdriver, tighten the screws
so the TV mounting plate is securely attached
to the TV.
DO NOT lay your TV face down when
attaching the TV mounting brackets.
This can cause permanent damage
to your screen. Lean it against a wall
or other solid surface so it remains
vertically upright.
DO NOT over tighten screws. Thread
screws carefully by hand before
tightening. If you feel any resistance,
remove the screw immediately.
The television should be unplugged
before threading any bolt or screw into
the back panel.
15
Hanging Your Flatscreen TV
on the Pivot Arm
1
With the help of another person, lift your TV
up to mount level. Raise the TV just above
the pivot arm. Slide the TV and mounting plate
downward onto end of the pivot arm.
2
Hang lower hooks on TV mounting plate to
pins that extend from pivot arm.
3
Place pivot washer, making sure it grabs the tilt
guides on the TV mounting plate.
16
Hanging Your Flatscreen TV
on the Pivot Arm (cont’d)
4
Firmly secure the TV mounting plate on
the pivot arm by threading the locking bolt
through the pivot washer on top of pivot arm.
Tighten the bolt with the supplied Allen key. Do
not over tighten.
17
Adjusting the Flexibility of the Tilt Mechanism
1
Using the supplied Allen key, adjust the locking
bolt on the top of the pivot arm to desired feel
of the tilt mechanism.
2
To adjust tilt angle, gently pull top of TV while
pushing the bottom to the desired position up
to 12°. Do the opposite to tilt up.
Panning from
Left to Right
Gently move your TV from side to side until it is
flush to the wall or completely extended at 90°
18
Routing Your TV’s Power Cord and AV Cable
through the Cable Management System
1
With the mount completely installed on the
wall and your TV properly secured to the
mount, fully extend the mount’s pivot arm.
2
Connect your TV’s power cord to the TV (if TV
uses a detachable-type power cord).
3
Slide the cable channel covers off the pivot arm,
as shown to the right.
19
Routing Your TV’s Power Cord and AV Cable
through the Cable Management System (cont’d)
4
Route your TV’s power cord through the
bottom cable channel.
5
Route AV cable from your wall, set-top box,
AV receiver, or other source through the
top channel, as shown to the right and make
connections to your TV.
6
Slide the cable channel covers back into place.
Cable channels are in place when you hear
them click.
7
Plug the TV power cord into an AC outlet.
NOTE: DO NOT run power and AV
cables in the same channel, as this may
cause electrical interference that can
affect picture and sound quality.
Congratulations
You’ve successfully installed your Monster SuperThin
™
FlatScreen Mount.
Visit us at www.MonsterCable.com/FlatScreen for more innovative Monster FlatScreen products.
20
More Great Products from Monster FlatScreen
™
Get the Look You Want and the Performance You Need.
For more details on all our Monster FlatScreen products, visit us at MonsterCable.com/FlatScreen
Safely clean your LCD or plasma atscreen TV
without staining, streaking, or dripping. Ultra-soft
MicroFiber cloth won’t scratch delicate screen
coatings.
Monster FlatScreen Cleaning Kit
Conceal unruly cords and cables for a clean, sleek
look. Easy to install with paintable covers to match
any decor.
Monster FlatScreen CleanView
™
Cable Manager
Monster Flatscreen Cables are compact and exible
for easy routing and installation. Exclusive Monster
patented technologies deliver the advanced
performance you need from your atscreen TV.
Monster FlatScreen Cables
™
Protect your atscreen TV from harmful surges and
spikes and maximize performance with Monster
Dual Mode Plus
™
surge protection and HD Clean
Power
®
ltering, designed specically for HDTVs.
Monster FlatScreen PowerProtect
™
and PowerCenters
™
Page is loading ...
Page is loading ...
/
