DFI PR611-C621 Owner's manual

DFI
Brand
DFI
Model
PR611-C621
Category
Motherboards
Type
Owner's manual
PR611-C621
A-583-M-2007
ATX Industrial Motherboard
User’s Manual
2User's Manual | PR611-C621
Copyright
This publication contains information that is protected by copyright. No part of it may be repro-
duced in any form or by any means or used to make any transformation/adaptation without the
prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions or
changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2020. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for com-
pliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
3User's Manual | PR611-C621
Table of Contents
Chapter 1 - Introduction................................................................................................................6
Specifications ......................................................................................................................... 6
Features .................................................................................................................................. 8
Block Diagram ........................................................................................................................9
Chapter 2 - Hardware Installation ................................................................................................8
Board Layout...........................................................................................................................8
LED and Switch ...................................................................................................................... 8
System Memory ..................................................................................................................... 9
Installing the DIMM Module ...........................................................................................9
Removing the DIMM Module ........................................................................................10
CPU ........................................................................................................................................11
Installing the CPU, Fan and Heat Sink .........................................................................11
Jumper Settings ...................................................................................................................13
Clear CMOS .................................................................................................................... 13
ME Firmware Update .....................................................................................................13
Rear I/O Ports .......................................................................................................................14
Graphics Display ............................................................................................................14
COM (Serial) ports .........................................................................................................15
RJ45 LAN Ports ............................................................................................................. 15
USB Ports ....................................................................................................................... 16
Internal I/O Connectors .......................................................................................................17
SATA (Serial ATA) ..........................................................................................................17
Front Audio .....................................................................................................................17
Cooling Fan Connectors ................................................................................................18
Power Connector ...........................................................................................................18
Chassis Intrusion ........................................................................................................... 19
Front Panel .....................................................................................................................19
Expansion Slots .............................................................................................................20
Installing the M.2 Module .............................................................................................20
LPC .................................................................................................................................21
Battery ............................................................................................................................22
SMBus ............................................................................................................................22
JTAG PLD Programming ............................................................................................... 23
Chapter 3 - BIOS Setup ............................................................................................................... 24
Overview ...............................................................................................................................24
Main .......................................................................................................................................25
Advanced .............................................................................................................................25
ACPI Configuration ........................................................................................................ 26
CPU Configuration .........................................................................................................27
Video Configuration .......................................................................................................27
SATA Configuration .......................................................................................................28
USB Configuration .........................................................................................................29
PCI Express Configuration ............................................................................................ 30
Debug Configuration .....................................................................................................31
UEFI Device Manager ....................................................................................................32
USB Power Control ........................................................................................................32
SIO NCT6112D ............................................................................................................... 33
SIO AST2500/AST2510 .................................................................................................35
H2O IPMI Configuration ................................................................................................35
Console Redirection ......................................................................................................38
Security .................................................................................................................................39
Boot .......................................................................................................................................39
Exit ......................................................................................................................................... 41
Updating the BIOS ................................................................................................................ 41
Notice: BIOS SPI ROM..........................................................................................................41
Chapter 4 - RAID ..........................................................................................................................42
RAID Levels ........................................................................................................................... 42
Setup Procedure ................................................................................................................... 42
4User's Manual | PR611-C621
About this Manual
This manual can be downloaded from the website.
The manual is subject to change and update without notice, and may be based on editions that
do not resemble your actual products. Please visit our website or contact our sales representa-
tives for the latest editions.
Warranty
1. Warranty does not cover damages or failures that occur from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper in-
stallation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in
or out of warranty. It must be returned to the purchase point, factory or authorized ser-
vice agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to
the product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you
are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, con-
tacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or
connectors by their ends.
Safety Measures
• To avoid damage to the system, use the correct AC input voltage range.
• To reduce the risk of electric shock, unplug the power cord before removing the sys-
tem chassis cover for installation or servicing. After installation or servicing, cover the
system chassis before plugging the power cord.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other
components. Perform the upgrade instruction procedures described at an ESD
workstation only. If such a station is not available, you can provide some ESD pro-
tection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
5User's Manual | PR611-C621
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 PR611-C621 motherboard
• 1 I/O shield
• 2 M.2 screw A32-112016-041G
• 1 CPU Clip 348-436471-100G
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Optional Items
• USB 2.0 port cable A81-001066-016G Length: 350mm
• LGA3647 cooler A71-101400-000G
• USB 3.1 Gen1 cable A81-001052-023G Length: 320mm
• Serial ATA data cable 332-553001-005G Length: 500mm
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
When installing the system board in a new system, you will need at least the following internal
components.
• CPU
• Memory module
• Storage device such as hard disk drive, CD-ROM, etc.
• Power supply
External system peripherals may also be required for navigation and display, including at least
a keyboard, a mouse and a video display monitor.
6
Chapter 1
INTRODUCTION
User's Manual | PR611-C621
Chapter 1 - Introduction
X Specifications
SYSTEM Processor 1st Generation Intel® Xeon® Scalable Processor Family, LGA
3647 Socket:
Intel® Xeon® Platinum 8160T (24 Cores, 27.5M Cache, up to
3.7 GHz); 150W
Intel® Xeon® Gold 6138T (20 Cores, 27.5M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 6138 (20 Cores, 27.5M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 6130T (16 Cores, 22M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 6130 (16 Cores, 22M Cache, up to 3.7 GHz);
125W
Intel® Xeon® Gold 6126T (12 Cores, 19.25M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 6126 (12 Cores, 19.25M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 5120T (14 Cores, 19.25M Cache, up to 3.2
GHz); 105W
Intel® Xeon® Gold 5119T (14 Cores, 19.25M Cache, up to 3.2
GHz); 85W
Intel® Xeon® Gold 5118 (12 Cores, 16.5M Cache, up to 3.2
GHz); 105W
Intel® Xeon® Silver 4116T (12 Cores, 16.5M Cache, up to 3.0
GHz); 85W
Intel® Xeon® Silver 4116 (12 Cores, 16.5M Cache, up to 3.0
GHz); 85W
Intel® Xeon® Silver 4114T (10 Cores, 13.75M Cache, up to 3.0
GHz); 85W
Intel® Xeon® Silver 4110 (8 Cores, 11M Cache, up to 3.0 GHz);
85W
Intel® Xeon® Silver 4109T (8 Cores, 11M Cache, up to 3.0
GHz); 70W
Intel® Xeon® Bronze 3106 (8 Cores, 11M Cache, 1.7 GHz); 85W
SYSTEM Processor 2nd Generation Intel® Xeon® Scalable Processor Family, LGA
3647 Socket:
Intel® Xeon® Gold 6252N (24 Cores, 35.75M Cache, up to 3.6
GHz); 150W
Intel® Xeon® Gold 6238T (22 Cores, 30.25M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 6230T (20 Cores, 27.5M Cache, up to 3.9
GHz); 125W
Intel® Xeon® Gold 6230N (20 Cores, 27.5M Cache, up to 3.5
GHz); 125W
Intel® Xeon® Gold 6230 (20 Cores, 27.5M Cache, up to 3.9
GHz); 125W
Intel® Xeon® Gold 6226 (12 Cores, 19.25M Cache, up to 3.7
GHz); 125W
Intel® Xeon® Gold 5220T (18 Cores, 24.75M Cache, up to 3.9
GHz); 105W
Intel® Xeon® Gold 5218T (16 Cores, 22M Cache, up to 3.8
GHz); 105W
Intel® Xeon® Gold 5218N (16 Cores, 22M Cache, up to 3.7
GHz); 110W
Intel® Xeon® Gold 5215 (10 Cores, 13.75M Cache, up to 3.4
GHz); 85W
Intel® Xeon® Silver 4216 (16 Cores, 22M Cache, up to 3.2
GHz); 100W
Intel® Xeon® Silver 4215 (8 Cores, 11M Cache, up to 3.5 GHz);
85W
Intel® Xeon® Silver 4214 (12 Cores, 16.5M Cache, up to 3.2
GHz); 85W
Intel® Xeon® Silver 4210 (10 Cores, 13.75M Cache, up to 3.2
GHz); 85W
Intel® Xeon® Silver 4209 (8 Cores, 11M Cache, up to 3.2 GHz);
70W
Chipset Intel
®
C621 Chipset
Memory 6 x 288-pin RDIMM up to 192GB
Single Channel DDR4 up to 2933 MHZ
IPMI
(optional)
BMC (AST2500) with DDR4, VGA, MGMT LAN, Serial COM, and
SPI Flash
BIOS Insyde SPI 128Mbit
GRAPHICS Display 1 x VGA (only with IPMI)
Single
Display
VGA (only with IPMI)
EXPANSION Interface 3 x PCIe x16 (Gen 3)
3 x PCIe x8 (Gen 3, shared with neighboring PCIe x16)
1 x M.2 M key 2280 (SATA/PCIe Gen3 x4 NVMe)
1 x M.2 E key 2230 (USB 2.0/PCIe Gen3 x2)
AUDIO Audio Codec ALC887
7
Chapter 1
INTRODUCTION
User's Manual | PR611-C621
ETHERNET Controller 2 x Intel
®
I210AT PCIe (10/100/1000Mbps)
1 x RTL8211F (only with IPMI)
REAR I/O Ethernet 2 x GbE (RJ-45)
1 x dedicated IPMI LAN (only with IPMI)
USB 4 x USB 3.1 Gen1
2 x USB 2.0
Display 1 x VGA (only with IPMI)
Serial 1 x RS-232 (DB-9)
INTERNAL I/O USB 2 x USB 2.0, Pin Headers (shared connector)
1 x USB 2.0 vertical Type A
2 x USB 3.1 Gen1, Pin Headers (shared connector)
SATA 6 x SATA 3 (up to 6Gb/s)
RAID 0/1/5/10
Serial 1 x BMC RS-232 Pin Header (only with IPMI)
SMBus 1 x SMBus
WATCHDOG
TIMER
Output &
Interval
System Reset, Programmable via Software from 1 to 255 sec/
Min
SECURITY TPM TPM 2.0 (optional)
POWER Type ATX
Connector Two 8-pin ATX 12V power
One 24-pin ATX power
RTC Battery CR2032 Coin Cell
OS SUPPORT Windows 10 IoT Enterprise LTSB RS5(64-bit)
Windows Server 2019
Windows Server 2016
Linux
ENVIRONMENT Temperature Operating: -5 to 65°C
Storage: -40 to 85°C
Humidity Operating: 5 to 90% RH, Non-condensing
Storage: 5 to 90% RH, Non-condensing
MECHANICAL Dimensions ATX Form Factor: 305mm (12") x 244mm (9.6")
Height PCB: 1.6mm
Top Side: 37.34mm
COOLER Heatsink Narrow ILM LGA 3647 (optional)
8
Chapter 1
INTRODUCTION
User's Manual | PR611-C621
X Features
Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so that
your system will continue to operate.
DDR4
DDR4 delivers increased system bandwidth and improves performance. The advantages of
DDR4 provide an extended battery life and improve the performance at a lower power than
DDR3/DDR2.
Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s.
Gigabit LAN
Two Intel
®
Gigabit LAN controllers (Intel
®
I210AT PCIe) support up to 1Gbps data transmis-
sion.
Audio
The Realtek ALC887 audio codec provides high-performance of 7.1 channel High Definition
audio output.
Wake-On-LAN
This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is
supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-
agement Event) signal. However, if your system is in the Suspend mode, you can power-on the
system only through an IRQ or DMA interrupt.
Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a system from the
S3 (STR - Suspend To RAM) state.
PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds
by forming multiple lanes. The x4 PCI Express lane supports transfer rate of 4 Gigabyte per
second (2 directions). The PCI Express architecture also supports high performance graphics
infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth (8GB/s in
each direction).
ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)
specification. ACPI has energy saving features that enables PCs to implement Power Manage-
ment and Plug-and-Play with operating systems that support OS Direct Power Management.
ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM
function.
With the Suspend to RAM function enabled, you can power-off the system at once by pressing
the power button or selecting “Standby” when you shut down Windows
®
without having to go
through the sometimes tiresome process of closing files, applications and operating system.
This is because the system is capable of storing all programs and data files during the entire
operating session into RAM (Random Access Memory) when it powers-off. The operating ses-
sion will resume exactly where you left off the next time you power-on the system.
Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-on the system
manually or let the system power-on automatically.
USB
The system board supports the new USB 3.1 Gen 1. It is capable of running at a maximum
transmission speed of up to 5 Gbit/s (625 MB/s), and is faster than USB 2.0 (480 Mbit/s, or 60
MB/s) and USB 1.1 (12Mb/s). USB 3.1 reduces the time required for data transmission, reduc-
es power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously acces-
sible external Plug and Play peripherals.
RTC Timer
The Real Time Clock (RTC) installed on the system board allows your system to automatically
power-on on the set date and time.
9
Chapter 1
INTRODUCTION
User's Manual | PR611-C621
X Block Diagram
VGA
Flash
RTL8211F
C621
SPI
USB 2.0 2x
M.2 M key
80h port
DDR4 1x
DDR4 1x
2nd Gen
Intel
®
Xeon
®
Scalable
processors
BMC
AST2500
Channel C
2400/2666/2933MHz
DDR4 1x
PCIe x16
PCIe x8
LPC
PCIe x1
VGA
SPI BIOS
PCIe x4/SATA
SATA 6x
PCIe x8
Channel B
2400/2666/2933MHz
Channel A
2400/2666/2933MHz
DMI
DDR4 1x
DDR4 1x
Channel F
2400/2666/2933MHz
DDR4 1x
Channel E
2400/2666/2933MHz
Channel D
2400/2666/2933MHz
SATA 3.0
USB 2.0
USB 2.0 1x
USB 2.0
USB 2.0 2x
USB 2.0
USB 3.1 Gen1 2x
USB 3.1 Gen1
USB 3.1 Gen1 4x
USB 3.1 Gen1
Intel
I210AT
GbE 1x
PCIe x1
Intel
I210AT
GbE 1x
Audio Codec
Realtek
ALC887
Front
Audio 1x
SPI
CPLD
GPIOs
TPM 2.0 (opt.)
Super IO
NCT6112D
UART
ADI
ADM213E
RS232 1x
Sensors
System Fan 3x & CPU Fan 1x
Switch
PCIe x8
PCIe x16
PCIe x8
PCIe x8
Switch
PCIe x8
PCIe x16
PCIe x8
PCIe x8
Switch
PCIe x8
M.2 E key
PCIe x2/USB 2.0
PCIe x1
USB 2.0 x2
LPC
RGMII
Dedicated LAN
MDI
DDR4
VGAVGA
COM Header
8
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
Chapter 2 - Hardware Installation
X Board Layout
DDR4_3
DDR4_2
DDR4_1
DDR4_4
DDR4_5
DDR4_6
CPU Socket LGA3647
Intel
C622
Intel
C621
M.2 M Key
2280
1 1 1 1 1 1
1
2 10
41
1
10
11
12
9
5
1
6
2
1
12
11
Battery
JP15
1
Power Driver
I
2
C Control
1
PLD Update
PCIe 4 (PCIe x8)
PCIe 6 (PCIe x8)
PCIe 3 (PCIe x16)
PCIe 5 (PCIe x16)
PCIe 2 (PCIe x8)
PCIe 1 (PCIe x16)
Chassis
Intrusion
Front Audio
2
111
12
LPC
Debug
COM2
Note
SMBus
2 8
1 7
LED9
LED10
LED5
LED4
+12V Power
+12V Power
+12V Power
4
8
1
5
5
1
8
4
CPU FAN
COM1
VGA
Note
LAN1
USB2
USB1
LAN2
USB4
USB3
USB 5/6
USB 3.1 Gen1
IPMI LAN
Note
USB10
USB11
TPM
Note
(btm side)
1
1
13
12
24
SPI Flash BIOS
1
1
System Fan 1
System Fan 2
Front
Panel
1 2
9 10
JP16
1
(USB 3.1 Gen1)
(USB 3.1 Gen1)
(USB 2.0)
USB 7
USB 2.0
USB 8/9
USB 2.0
SATA 5 - 0 (left to right)
Buzzer
PWR
RST
BMC
SPI
BMC
Note
AST2500
CPLD
MachXO2
M.2 E Key
2230
1
System
Fan 3
Nuvoton
NCT6112D
LCMXO2-7000HC
SIO
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives,
add-in boards, and other components. Perform installation procedures at an ESD
workstation only. If such a station is not available, you can provide some ESD pro-
tection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
Note:
Some components are optional and only available upon request.
X LED and Switch
SATA LED
Power Button
Reset Button
BMC Heartbeat LED (right);
Status LEDs (left and middle): Green=Normal, Amber=Abnormal
9
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
• Six 288-pin RDIMM up to 192GB
• Single Channel DDR4 up to 2933 MHz
X System Memory
Features
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits from the memory channels. DIMMs are on the same
channel. DIMMs in a channel can be identical or completely different. However, we highly rec-
ommend using identical DIMMs. Not all slots need to be populated.
DDR4_3
DDR4_4
DDR4_1
DDR4_6
DDR4_2
DDR4_5
Before installing the memory module, please make sure that the following safety cautions are
well-attended.
1. Make sure the PC and all other peripheral devices connected to it has been powered
down.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board
4. Make sure the notch on memory card is aligned to the key on the socket.
Socket Side View
Socket Top View
Memory Module
Notch
Key
Eject TabEject Tab
Step 3
Step 2
Step 1 Step 1
Step 2
Step 3
Socket Side View
Socket Top View
Memory Module
Key
Eject TabEject Tab
Step 3
Step 2
Step 1
Step 1
Step 2
Step 3
Notch
Retention Notch
X System Memory
Installing the DIMM Module
10
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
Please follow the steps below to install the memory card into the socket.
Step 1:
Press the eject tabs at both ends of the socket outward and downward to release them from
the locked position.
Step 2:
Insert the memory card into the slot while making sure the notch and the key are aligned.
Press the card down firmly with fingers while applying and maintaining even pressure on both
ends.
Step 3:
The tabs snap automatically to the edges of the card and lock the card in place.
Socket Side View
Socket Top View
Memory Module
Notch
Key
Eject TabEject Tab
Step 3
Step 2
Step 1
Step 1
Step 2
Step 3
Socket Side View
Socket Top View
Memory Module
Key
Eject TabEject Tab
Step 3
Step 2
Step 1
Step 1
Step 2
Step 3
Notch
Retention Notch
X System Memory
X Installing the DIMM Module
Socket Side View
Socket Top View
Memory Module
Notch
Key
Eject TabEject Tab
Step 3
Step 2
Step 1
Step 1
Step 2
Step 3
Socket Side View
Socket Top View
Memory Module
Key
Eject TabEject Tab
Step 3
Step 2
Step 1
Step 1
Step 2
Step 3
Notch
Retention Notch
Please follow the steps below to remove the memory card from the socket.
Step 1:
Press the eject tabs at both ends of the socket outward and downward to release them from
the locked position.
Step 2:
The memory card ejects from the slot automatically.
Step 3:
Hold the card by its edges and remove it from the slot.
X System Memory
Removing the DIMM Module
11
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
Installing the CPU, Fan and Heat Sink
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circula-
tion across the CPU and heat sink, the CPU will overheat damaging both the CPU and system
board.
1. Before you place the CPU on the heat sink, you must apply a thermal paste onto the
top of the heat sink. The thermal paste is usually supplied when you purchase the fan
with heat sink assembly. Do not spread the paste all over the surface. When you later
place the CPU on top of the heat sink, the compound will disperse evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan with heat sink already has a patch of thermal paste on its underside.
Peel the strip that covers the paste before you place the CPU on top of the heat sink.
2. To insert the CPU into the CPU carrier, please first locate the gold triangular mark on
the CPU. The triangular mark must align with the triangular corner of the CPU carrier
shown on the photo. Without touching the pins, press the CPU onto the carrier until the
CPU is retained by the latches.
CPU (side view, bottom up)
CPU Carrier (side view, bottom up)
CPU Carrier (bottom view)
Latch
X CPU
The system board is equipped with a surface mount LGA 3647 socket. This socket is exclu-
sively designed for installing a LGA 3647 packaged Intel CPU.
Protective cap
Protective cap
Important:
1. Before you proceed, make sure (1) the LGA 3647 socket comes with 2 protec-
tive caps, (2) the caps are not damaged and (3) the socket’s contact pins are not
bent. If the caps are missing or the caps and/or contact pins are damaged, con-
tact your dealer immediately.
2. Make sure to keep the protective caps. RMA requests will be accepted and pro-
cessed only if the LGA 3647 socket comes with the protective caps.
Note:
A boxed Intel
®
processor already includes the CPU fan and heat sink assembly. If
your CPU was purchased separately, make sure to only use Intel®-certified fan and
heat sink.
Gold triangular
mark
CPU Carrier
(bottom view)
Latch
Latch
Triangular
mark
12
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
5. Align the triangular mark of
the CPU and CPU carrier to
the chamfer corner of the
CPU and heat sink socket.
Place the heatsink assem-
bly on top of the socket.
Use the T30 screwdriver
to install the assembly ac-
cording to the sequence of
the screws shown on the
label.
6. Connect the CPU fan’s
power cable to the CPU fan
connector on the system
board.
3. Place the CPU carrier on
top of the heatsink. Place
the triangular hole near the
mounting hole #1 of the
heat sink. Use the push-
pins around the CPU car-
rier to secure the CPU car-
rier onto the heat sink.
You will hear a distinctive
“click”, indicating the CPU
carrier is correctly locked
into position.
Mounting hole #1 of the
heat sink (top view)
Mounting hole #1 (bottom view)
Triangular hole
4. Slide the protective caps
open and detach them
from the board.
Chamfer corner of the
CPU and heatsink socket
CPU Carrier with CPU
(side view, bottom up)
Push PinPush Pin
Heatsink
(side view, bottom up)
X CPU
CPU Fan
13
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
X Jumper Settings
Clear CMOS
JP15
JP16
If any anomaly of the followings is encountered —
a) CMOS data is corrupted;
b) you forgot the supervisor or user password;
c) failure to start the system due to BIOS mis-configuration
— it is suggested that the system be reconfigured with default values stored in the ROM BIOS.
To load the default values stored in the ROM BIOS, please follow the steps below.
1. Power-off the system and unplug the power cord.
2. Put a jumper cap on pin 2 and pin 3. Wait for a few seconds and set it back to its de-
fault setting, i.e. jumper cap on pin 1 and pin 2.
3. Plug the power cord and power-on the system.
2-3 On: Clear CMOS
2-3 On: Force ME Update
1-2 On: Normal (default)
1-2 On: Normal (default)
ME Firmware Update
JP16 is used for updating the ME firmware.
13 2
13 2
31 2 31 2
14
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
X Rear I/O Ports
USB 4 (USB 3.1 Gen 1)
LAN 2
USB 2 (USB 3.1 Gen 1)
LAN 1
USB 3 (USB 3.1 Gen 1)USB 1 (USB 3.1 Gen 1)
COM 1
USB 11 (USB 2.0)
USB 10 (USB 2.0)
IPMI LAN (optional)
VGA (optional)
Graphics Display
A VGA display port of DB15 connector is available when the motherboard is with IPMI func-
tions and BMC.
VGA Port
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable
connector to the VGA port. After you plug the monitor’s cable connector into the VGA port, gen-
tly tighten the cable screws to hold the connector in place.
Optional VGA (DB15)
Rear I/O Connectors
PCB
I/O Connectors
15
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
COM (Serial) ports
COM 1 (DB9)
BMC COM port (COM 2)
The serial ports are asynchronous communi-
cation ports with 16C550A-compatible UARTs
that can be used with modems, serial print-
ers, remote display terminals, and other serial
devices.
The two COM ports support RS232 — one DB9
connector at the rear side and one internal
pin-header connector for monitoring the BMC.
RS232
Pin DB9 Pin header
1 DCD DCD
2 RXD RXD
3 TXD TXD
4 DTR DTR
5 GND GND
6 DSR DSR
7 RTS RTS
8 CTS CTS
9 RI RI
COM Port Pin Assignment
X Rear I/O Ports
Note:
The BMC COM port is used to monitor the IPMI, and may not be present when
your model does not support IPMI.
RJ45 LAN Ports
• 2 x Intel
®
I210AT PCIe (10/100/1000Mbps)
• 1 x RTL8211F only with IPMI
The LAN ports allow the system board to connect to a local area network (LAN) by means of a
network hub. The IPMI LAN is only available with IPMI.
Features
X Rear I/O Ports
LAN 2LAN 1
IPMI LAN (optional)
1
9
2
16
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
USB Ports
The USB device allows data exchange between your computer and a wide range of simultane-
ously accessible external Plug and Play peripherals. The system board is equipped with mul-
tiple USB ports as listed below:
• 4 x USB 3.1 Gen 1 rear ports (USB 1/2/3/4)
• 2 x USB 3.1 Gen 1 internal ports, box headers (USB 5/6)
• 3 x USB 2.0 internal ports, one pin headers (USB 8/9) and one Type A (USB 7)
• 2 x USB 2.0 rear ports (USB 10/11)
The internal USB ports may be mounted on a card-edge bracket. Install the card-edge bracket
to an available slot at the rear of the system chassis and then insert the USB port cables to a
connector.
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state.
USB 8/9 (USB 2.0)
USB 7 (USB 2.0) USB 5/6 (USB 3.1 Gen 1)
Pin Assignment Pin Assignment
1 VCC 2 VCC
3 D- 4 D-
5 D+ 6 D+
7 GND 8 GND
9 KEY 10 N.C.
Pin Assignment Pin Assignment
1 PWR 11 D2+
2 SSRX1- 12 D2-
3 SSRX1+ 13 GND
4 GND 14 SSTX2+
5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND
7 GND 17 SSRX2+
8 D1- 18 SSRX2-
9 D2+ 19 PWR
10 N.C. 20 ---
USB 2.0 Box Headers USB 3.1 Box Headers
X Rear I/O Ports
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or
more USB ports, the +5V_standby power source of your power supply must support
≥2A.
USB 4 (USB 3.1 Gen 1)USB 2 (USB 3.1 Gen 1)
USB 3 (USB 3.1 Gen 1)USB 1 (USB 3.1 Gen 1)
USB 11 (USB 2.0)
USB 10 (USB 2.0)
1
210
9
1 4
1 10
11
17
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
X Internal I/O Connectors
SATA Pin Assignment
The Serial ATA (SATA) connectors are used to connect the Serial ATA device. SATA 3.0 is sup-
ported by the five SATA ports and provides data rate up to 6Gb/s. Connect one end of the Se-
rial ATA cable to a SATA connector and the other end to your Serial ATA device.
SATA (Serial ATA)
SATA 5/4/3/2/1/0 from left to right
• 6 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s
• Integrated Advanced Host Controller Interface (AHCI) controller
• Support RAID 0, RAID 1, RAID 5, RAID 10
Features
X Internal I/O Connectors
7
RX-
GND
TX+
TX-
GND
1
RX+
GND
The Front Audio internal connector allows you to connect to audio jacks at the front panel of
your system.
Front Audio
Pin Assignment Pin Assignment
1 Mic-L 2 GND
3 Mic-R 4 N.C.
5 Line-Out-R 6 Mic-JD (sense)
7 GND 8 KEY
9 Line-Out-L 10 Line-JD (sense)
Front Audio Pin Assignment
1
9
2
10
Front Audio
18
Chapter 2
HARDWARE INSTALLATION
User's Manual | PR611-C621
X Internal I/O Connectors
PWM Fan
4-pin Fan Pin Assignment
Pin Assignment
1 Ground
2 Power
3 Sense
4 Speed Control
Cooling Fan Connectors
X Internal I/O Connectors
1
These fan connectors are used to connect cooling fans. The cooling fans will provide adequate
airflow throughout the chassis to prevent overheating the CPU and system board components.
The 4-pin fans provide PWM to modulate fan speed.
CPU Fan (PWM)
System Fan 1 (PWM)
System Fan 2 (PWM)
System Fan 3 (PWM)
Power Connector
Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1. An
ATX12V power supply unit has a standard 24-pin ATX main power connector that must be in-
serted into the 24-pin connector. The 8-pin +12V power connector enables the delivery of more
+12VDC current to the processor’s Voltage Regulator Module (VRM).
The power connectors from the power supply unit are designed to fit the 24-pin and 8-pin con-
nectors in only one orientation. Make sure to find the proper orientation before plugging the
connectors.
The system board requires a minimum of 300 Watt power supply to operate. Your system con-
figuration (CPU power, amount of memory, add-in cards, peripherals, etc.) may exceed the mini-
mum power requirement. To ensure that adequate power is provided, we strongly recommend
that the system is supplied with a minimum of 400 Watt power.
ATX 24-pin Power
Connector
ATX 8-pin Power Connectors
+3.3V
+3.3V
GND
+5V
GND
+5V
GND
PWR_OK
+5VSB
+12V
+12V
+3.3V
+3.3V
-12V
GND
PS_ON#
GND
GND
GND
NC
+5V
+5V
+5V
GND
1
13
12
24
14
58
GND
+12V
1 4
5 8
GND
+12V
Important:
Insufficient power supplied to the system may result in instability or malfunction
of the add-in boards and peripherals. Calculating the system’s approximate power
usage is important to ensure that the power supply meets the system’s consump-
tion requirements.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

DFI PR611-C621 Owner's manual

DFI
Brand
DFI
Model
PR611-C621
Category
Motherboards
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents