Newtech P1100BB is a bathroom towel rail designed to warm and dry towels. It features a vertical design with a small footprint against the wall. The rail is easy to install and can be mounted on solid fixing points like timber or brickwork. It requires a 12V AC isolating transformer which should be located in a dry, accessible location. The rail has a wattage of 40W and comes with waterproof wirenut connectors providing an IPX7 rating. For safety, it should be installed at least 600mm above the floor and out of reach from wet areas.
Newtech P1100BB is a bathroom towel rail designed to warm and dry towels. It features a vertical design with a small footprint against the wall. The rail is easy to install and can be mounted on solid fixing points like timber or brickwork. It requires a 12V AC isolating transformer which should be located in a dry, accessible location. The rail has a wattage of 40W and comes with waterproof wirenut connectors providing an IPX7 rating. For safety, it should be installed at least 600mm above the floor and out of reach from wet areas.
BATHROOMWARE DESIGN & INNOVATION
Newtech recommends that a registered electrician install this
product and that it is installed to the current wiring regulations
and in particular to those regulations that include the installation
of appliances and accessories in damp environments such as
bathrooms. It must be installed in accordance with relevant
Australian/New Zealand Standards (AS/NZS).
This electrical appliance is intended to warm and dry towels and therefore hot
to touch. Young children or infirm persons should be supervised to ensure that
they do not play with or misuse the appliance. The towel rail has been designed
to withstand the loads expected during normal operation as a towel rail. The
towel rail is not a climbing pole and should not be used as such. The appliance
will feel hotter to touch during Summer periods because of the rise in ambient
temperature. The insulation eect of towels will cause the operating temperature
to increase. The appliance is ONLY used for warming and drying towel, DO NOT
use it for any other purpose.
ELECTRICAL
The Polo towel rail must be wired by a registered electrician. An isolating
switch must be positioned near the towel rail but out of reach from wet areas
like baths and showers. A wall or ceiling cavity must be available to conceal
the transformer. All rails must be connected to the 12 Volt transformer in
parallel and cannot be connected directly to 240V supply. See Figure 6.0
Only one end of the pole should be connected to the power source. The
other end will need to have wires terminated as 2 separate looms in the rail.
See Figure 1.0 and 4b
WALL MOUNTING
The towel rail mounting spigot must be fastened to a solid fixing point,
eg. timber or brickwork. The mounting face of the towel pole must be fitted
against a solid surface eg. tiles (not suitable directly onto gib or plasterboard).
Recommended location is 600mm above floor, 300mm from any permanent
fixing and 250mm between poles. See Figure 1.0
WARNING
The Polo vertical rail has a small footprint against the wall and secureness
should be periodically checked. The Allen Key securing the rail may require
tightening especially during the settling period. The cable holes and fixing
holes must be neatly and accurately drilled. For drilling through hard surfaces
eg. porcelain tiles, marble or granite etc, a diamond core drill must be used.
Ensure final rail position will conceal wiring hole.
SPECIFICATIONS AND DIMENSIONS
Model Dimensions Wattage
P1100 H1100 x W50 x D132 40W
The Polo rail uses 12 Volts AC isolating transformer.
Ensure the combined total wattage for rails doesn’t exceed transformer rating.
newtech.co.nz
Head Oce & Distribution Warehouse | 281 Heads Road, Wanganui
Phone: 06 349 0194 or 0800 728 662, [email protected]
Auckland Concept Showroom | 525 Great South Road, Penrose, Auckland
Phone: 09 930 6200, aucklandshowroom@newtech.co.nz
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
WARNING: In order to avoid a hazard for very young children, this appliance
should be installed so that the lowest heated rail is at least 600 mm above the
Fig 1.0
Fixed wiring
Transformer
12V wiring
Studs
Nogs
page 2 of 5
CORTO 350, 550, 750
INSTALLATION INSTRUCTIONS
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
WARNING: In order to avoid a hazard for very young children, this appliance
should be installed so that the lowest heated rail is at least 600 mm above the
• Must be installed by a registered electrician.
• The 12V ‘safety isolating’ transformer supplied must be located in a
dry accessable location (do not cover with insulation).
• Distance from transformer to towel rail must be less than 2 metres.
• Typical transformer locations include:
- ceiling cavity
- wall cavity (behind switch plate)
- cupboard
accordance with wiring guidlines AS/NZS 3000:2000.
• The waterproof wirenut connectors provide an IPX7 rating
• The towel rail may be installed in wet area electrical zones 1, 2 & 3 as
• Manufactured and tested to AS/NZS 60335.2.43
• Minimum 50 mm clearance to surrounding surfaces.
1. WALL PREPARATION
Fig 1.0
Fixed wiring
Transformer
12V wiring
Studs
Nogs
4” GRINDER
Fig 2.0
page 2 of 5
FIGURE 1FIGURE 2FIGURE 3
Appliance wire
supplied
Black polytube
wedged in slot
250mm
Figure 1.0
Installation Instructions
Polo Vertical Heated Rail
SAFETY INFORMATION
Figure 2.0
Ø15mm hole for
insulated power
wall connector
Solid timber
framing
Screw location
Centres 898mm
Connect one
side only
Figure 3.0
Towel Rail
Wall Switch
Transformer
N
L
Mains
12 Volt
Ecotimer
Red
Blue
Brown
Towel Rail
Towel Rail
Towel Rail
Wall Switch
Transformer
N
L
Mains
12 Volt
Towel Rail
Towel Rail
Towel Rail
Wall Switch
Transformer
N
L
Mains
12 Volt
Ecotimer
Red
Blue
Brown
Towel Rail
Towel Rail
Towel Rail
Wall Switch
Transformer
N
L
Mains
12 Volt
Towel Rail
Towel Rail
Towel Rail
Wall Switch
Transformer
N
L
Mains
12 Volt
Ecotimer
Red
Blue
Brown
Towel Rail
Towel Rail
Towel Rail
Wall Switch
Transformer
N
L
Mains
12 Volt
Towel Rail
Towel Rail
BATHROOMWARE DESIGN & INNOVATION
Installation Instructions
Polo Vertical Heated Towel Rail
INSTALLATION
• Typical wiring for timber framed walls is shown in Figure 1.0
• The distance from the transformer to the furthest 12V connection
should be no more than 2000mm.
• Make sure that the 12V cabling doesn’t cross the 230V mains cable.
• Insulation should be removed from the vicinity of the transformer to a
radius of 150mm.
BEFORE LINING
• For each pole, drill a Ø15mm hole for the power insulator in wall framing.
Check insulator is going to be a firm fit in the hole.
• Use a level to make sure that these holes are plumb. See Figure 2.0
• The recommended horizontal distance between rails is 250mm.
• Wire requires threading through the Ø15mm insulator hole as shown in
Figure 1.0 and connected to the 12V transformer.
AFTER LINING
• Fix the first pole and work across
• Fix insulator in Ø15mm hole using a bonding or silicon glue, at cable end.
See Figure 4b
• Take care to ensure that the rail, in its final position, will fully conceal the
wiring and cable hole.
• Use a level to determine the correct position for the blocks at the
non-cabled end. See Figure 4b
• Fix the mounting blocks at the non-cabled end.
• Connect the appliance wiring to the rail as per NZ electrical requirements.
• Make sure that there are no white and blue wires connected as this would
create a short circuit.
• DO NOT PULL THE WIRE OUT OF THE TOWEL RAIL - THIS WIRE IS
CONNECTED TO THE INTERNAL HEATING CABLE. PULLING OUT
THE WIRE WILL EXTRACT THE HEATED SEGMENT.
• Push the towel rail onto the mounting spigots until flush with the wall.
• Fix the towel rail in position using the Allen key provided.
• Continue to fit the remaining rails using the same procedure.
CARE & CLEANING
• Do not use cream cleaner or any abrasive or corrosive cleaners.
• The heated towel rails are best wiped down from time to time
with a soft clean cloth moistened with warm soapy water. Fingerprints can
be removed by using a dry, soft microfibre cloth.
Disclaimer: Products in these installation instructions must by regulation be installed
by a licensed and registered tradesperson. Newtech cannot be held responsible if
the installation and use of the towel rails is not carried out in accordance with these
instructions or for materials not supplied by Newtech. The manufacturer/distributor
reserves the right to vary specifications without prior notification.
Head Oce & Distribution Warehouse: 281 Heads Road, Wanganui, Phone: 06 349 0194 or 0800 728 662, [email protected], newtech.co.nz
Auckland Concept Showroom: 525 Great South Road, Penrose, Auckland, Phone: 09 930 6200, [email protected]
Figure 4a
Figure 5.0
Towel Rail
Wall Switch
Transformer N
L
Mains
12 Volt
Ecotimer
Red
Blue
Brown
Towel Rail
Towel Rail
Towel Rail
Wall Switch
Transformer N
L
Mains
12 Volt
Towel Rail
Towel Rail
Figure 4b
Polo rail wall connection
Polo rail wall connection2
Bottom
Top
Unpowered leg installation
Power wire insulator for
Ø15mm hole in wall
Powered leg installation
Spigot wall connector
for unpowered leg
screw mounts to wall
Cut wire for
unpowered leg
-
1
-
2
Newtech P1100BB is a bathroom towel rail designed to warm and dry towels. It features a vertical design with a small footprint against the wall. The rail is easy to install and can be mounted on solid fixing points like timber or brickwork. It requires a 12V AC isolating transformer which should be located in a dry, accessible location. The rail has a wattage of 40W and comes with waterproof wirenut connectors providing an IPX7 rating. For safety, it should be installed at least 600mm above the floor and out of reach from wet areas.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Newtech P1100 User manual
-
Newtech SL130 User manual
-
Newtech WESTFIELD Installation guide
-
Newtech Broadway Installation guide
-
Newtech Freestanding and Back to Wall Baths User manual
-
Newtech CL120H430 User manual
-
Newtech Mod Odourless Floor Mounted Toilet Pan and Cistern User manual
-
Newtech Toilet Installation guide
-
Newtech 8030 User manual
-
Newtech 9408 User manual
Other documents
-
Lyfco S01B User manual
-
SUSSEX DGTR300 User manual
-
COLDBUSTER HTW-1RHS User guide
-
COLDBUSTER HTW-1RVR User manual
-
THE HEATING COMPANY Hotwire Operating instructions
-
HEIRLOOM WHSPLV1000 User manual
-
THE HEATING COMPANY Hotwire Operating instructions
-
Thermogroup SS4412 Installation guide
-
Redring X10R Expressions Revive 10.5kW User manual
-
Thermogroup VP900B Installation guide
