Newtech WESTFIELD Installation guide

WESTFIELD
Brand
Newtech
Model
WESTFIELD
Type
Installation guide

Newtech WESTFIELD Mirror Demister keeps your mirrors mist-free and clear. Simply operate the demister for a few minutes before showering or bathing. Suitable for mirrors from 400mm to 1200mm in width. Easy to install with self-adhesive backing. Requires a registered electrician for wiring and connections. Say goodbye to foggy mirrors and enjoy a clear reflection every time.

Newtech WESTFIELD Mirror Demister keeps your mirrors mist-free and clear. Simply operate the demister for a few minutes before showering or bathing. Suitable for mirrors from 400mm to 1200mm in width. Easy to install with self-adhesive backing. Requires a registered electrician for wiring and connections. Say goodbye to foggy mirrors and enjoy a clear reflection every time.

BATHROOMWARE DESIGN & INNOVATION
Newtech recommends that a registered electrician install this product and that it is installed to the current wiring regulations
and in particular to those regulations that include the installation of appliances and accessories in damp environments such
as bathrooms. It must be installed in accordance with relevant Australian/New Zealand Standards (AS/NZS).
The Westfield Mirror Demister [9087] is designed to leave the range of Westfield mirrors mist
free and clear depending on the bathroom environment [see note below]. The mirror demister
should be operated for a few minutes before turning on the shower or running a bath.
newtech.co.nz
Head Oce & Distribution Warehouse
281 Heads Road, Wanganui
Phone: 06 349 0194 or 0800 728 662
[email protected]
Westfield Mirror Demister [9087]
Specification & Installation Instructions
IMPORTANT: Please note a registered electrician is required to complete all wiring installation and connections.
INSTALLATION INSTRUCTIONS
Lay the Westfield mirror face down on a protective and cushioned surface. Clean the reverse side of
the mirror surface making sure it is dry, free of dust and contaminants. Mark the position of the heat
pad on the back side of the mirror.
Turn the heat pad over. Remove approximately 10cm of the protective film and fold it back.
Turn the heat pad again, adjust it to the marked position. Using a dry cloth press the adhesive side to
the reverse side of the mirror.
Slowly peel the protective film while pressing and rubbing the adhesive side onto the reverse side of
the mirror using a dry cloth.
1.
2.
3.
4.
Mirror Size Demister Size Demister Required Watts
400mm 310mm x 450mm One 2.5W/dm2
500mm 310mm x 450mm One 2.5W/dm2
600mm 310mm x 450mm One 2.5W/dm2
750mm 310mm x 450mm One 2.5W/dm2
900mm 310mm x 450mm One 2.5W/dm2
1200mm 310mm x 450mm Two 5W/dm2
Sizing Guide
Auckland Concept Showroom
525 Great South Road, Penrose, Auckland
Phone: 09 930 6200
[email protected]
Note: The 1200mm Westfield Mirror requires x2 Demisters
Demister Note: Typically, a mirror fogs up due to the dierence in temperature of the mirror and the temperature in the bathroom. The
bathroom is warm from the shower or bath whilst the mirror is cold and this dierence in temperature causes it to fog up. The mirror
demister warms the mirror slowly to reduce the dierence in temperature leading to the mirror to defog slowly. The rate at which it
defogs will be dependant on the size of the Mirror, the demister pad and the size and environment of the bathroom.
  • Page 1 1

Newtech WESTFIELD Installation guide

WESTFIELD
Brand
Newtech
Model
WESTFIELD
Type
Installation guide

Newtech WESTFIELD Mirror Demister keeps your mirrors mist-free and clear. Simply operate the demister for a few minutes before showering or bathing. Suitable for mirrors from 400mm to 1200mm in width. Easy to install with self-adhesive backing. Requires a registered electrician for wiring and connections. Say goodbye to foggy mirrors and enjoy a clear reflection every time.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents