TDX 730310 User manual

Brand: TDX

Model: 730310

Type: User manual

TDX 730310 is a powerful bathroom heater with multiple heat settings and a fan for air circulation. Its 2035W of power and two heat settings (1000W and 2000W) allow for quick and efficient heating of your bathroom. The fan-only mode provides air circulation without heat, perfect for keeping the room fresh and comfortable. Safety features like overheating protection and an automatic shut-off after two hours of continuous operation ensure peace of mind.

730310 & 730311

INSTRUCTION MANUAL

Technical parameter:

Product Name

Bathroom Heater

Rated voltage 220-240V

Model 730310 | 730311

Rated frequency 50Hz

Appliance Type Class  Rated power 2035W

Degree of proteon

(when wall-mounted)

IPX0

StandardsIE C 60335-1 IEC 60335-2-30 IEC 60335-2-80

Product structure diagram

Electrical diagram

Air inlet

Air outlet

Installation

Check whether all parts are complete before using.

1 Determine the installaon locaon: When using this product on a wall, install it at the height

required by the user (the air outlet is at least 100cm from the ground, and the top air inlet is

at least 30cm from the ceiling), and it must be far away from the shower head and bathtub,

as shown in Figure 1. Show.

2 First, drill two8mm holes with a distance of 180mm on a solid wall according to the height

shown in thegure, and the holes depth is more than 35mm. Then drive the expansion tube

provided by the machine into the holes, screw on the self-tapping screw provided, and leave

a distance of 3-5mm from the top of the screw.

3 Insert the two round holes on the back of the heater into the screw heads hung on the wall,

and then move it horizontally to the le into the slot, and then move it down vercally to

complete the wall-mounted installaon of the heater.

Instructions for use

Power check before turn on

1. Whether the power cord is in good condon.

2. The power supply of the product is 220-240V AC, and the carrying capacity of the socket

should not be less than 10A, otherwise accidents may occur.

Instructions

1. Plug in the power plug, touch the power icon “ ”, and hear a beep, the heater turns on.

2. Touch the Heater I icon " " the heater will work at 1000W.

3. Touch the Heater II icon " ", the heater will work at 2000W.

4. Touch the Fan icon " ", the machine only ventilation, but the PTC heating element does

not work ,the inside motor will work at 35W.

5. While the heater II icon" " & " " working together, the heater working at max

power 2035W.

6. Touch the Power icon " " again, the heater stops working.

Safety protection

1. Overheating protection: When the use environment is abnormal or improper use causes the

internal temperature of the product to be too high, the temperature control element can

automatically cut off the power supply and the product stops working; after the whole heater

is cooled and the abnormality is eliminated, it can resume normal use;

2. After two hours of continuous operation, the heater will automatically shut down by default.

Press the power switch again to resume normal use.

Precautions

1. Before using the product, please check whether the power supply you are using meets the

requirements of the nameplate, and pay attention to the rated current of the socket above

10A.

2. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard.

3. Do not cover ; WARNING: In order to avoid overheating, do not cover the

heater.

4. It is forbidden to use it in high temperature, humidity, flammable, explosive, heated and

easily deformed, discolored, or deteriorated objects or in places with severe dust

5. The ambient temperature of use should not exceed 40℃, and do not use it in places that are

easy to be sucked in, such as curtains, to prevent fire. There should be no shelter within 30cm

of the top to facilitate air circulation.

6. That the heater is to be installed so that switches and other controls cannot be touched by a

person in the bath or shower.

7. The heater installation close to curtains and other combustible materials may pose a fire

hazard. It should be placed at least 50cm away from curtains and other combustible

materials.

8. It is strictly forbidden to insert thin metal wires or foreign objects into any holes in the

machine to avoid electric shock or damage.

9. It is strictly forbidden to share sockets with other high-power electrical appliances. It is

strictly prohibited to move the product directly by pulling the power cord.

10. It is forbidden to use the product against the power socket, the heater must not be located

immediately below a socket-outlet.

11. It is forbidden to use products as heat preservation and heating equipment for animals and

plants

12. This product is only suitable for indoor use, not for outdoor use.

13. When the product is in normal use or idle, it should be more than 1.5 meters away from the

fire source or flame, and avoid direct sunlight.

14. This appliance is not intended for use by persons (including children) with reduced

physical,sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play

with the appliance.

15. When using the product, in order to avoid burns, please do not let bare skin directly touch

the surface of the air outlet.

16. Do not unplug the power cord with wet hands, as there is a risk of electric shock or electric

shock.

17. When leaving or not in use for a long time, please be sure to cut off the power and unplug

the power plug.

18. Turn off the power before unplugging the plug; do not pull the power cord, but pull the

power plug, otherwise it may cause short circuit, fire, electric shock and other hazards.

19. Ensure that the fan is switched off from the supply mains before removing the guard.

Common malfunctions

Problem Possible cause of the problem Solution

Not work ●The plug is not inserted properly

●Heater damage

●Check whether the plug is

correctly inserted into the socket

●Send to repair shop for repair

Sudden shutdown

while heating

●The temperature exceeds the

threshold of the temperature limiter

●Has been working continuously for

two hours

●Use the standby unit after

cooling down

●Restart, select the corresponding

function key to work

Spare parts List

User Manual (1pcs) Screw (2 pcs) Expansion t ube (2 pcs)

Warranty

1. The heater is guaranteed for one year from the date of sale (subject to the invoice or proof of

purchase).

2. The following situaons do not belong to the scope of product " guarantees" maintenance

services, but our maintenance department will s serve you wholeheartedly (corresponding

fees will be charged):

1 Consumers are damaged due to improper use, maintenance and storage;

2 Damage caused by the disassembly of the company's designated special maintenance

department;

3 Products without valid purchase cecates or products with altered valid purchase

cecates;

4 Products that exceed the specied warranty period;

5 Products damaged due to unstable power supply voltage or beyond the normal voltage range

(198V-242V), or power cord installaon that does not conform to the naonal electrical

installaon;

6 Products damaged due to irresisble natural disasters;

7 The instruons specify products that are not suitable for use and are damaged due to

incorrect use.

TDX 730310 User manual

TDX 730310 User manual

Other documents