State GS6-30-MDV250, GS6-40-MDV- 250, GS6-50-MDV-250 User manual

Brand: State

Model: GS6-30-MDV250, GS6-40-MDV- 250, GS6-50-MDV-250

Category: Water heaters & boilers

Type: User manual

This manual is also suitable for

100291750_2000547498_(Rev. B)

November 2017

Installa on Instruc ons and

Use & Care Guide

Keep this manual in the pocket on heater for future reference whenever maintenance, adjustment or service is required.

Retain your original receipt as proof of purchase.

Read this manual and the labels on the water heater before you install,

operate, or service it. If you have diﬃ culty following the direc ons, or

aren’t sure you can safely and properly do any of this work yourself:

Call our Technical Assistance Hotline at 1-800-365-0024. We can help you with

installa on, opera ons, troubleshoo ng, or maintenance. Before you call, write

down the model and serial number from the water heater’s data plate.

Incorrect installa on, opera on, or service can damage the water heater, your house

and other property, and present risks including ﬁ re, scalding, electric shock, and

explosion, causing serious injury or death.

Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your

building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instruc ons.

• If you cannot reach your gas

supplier, call the ﬁ re department.

Installa on and service must be

performed by a qualiﬁ ed installer,

service agency or the gas supplier.

WARNING: If the informa on in

these instruc ons is not followed

exactly, a ﬁ re or explosion may

result causing property damage,

personal injury or death.

LOW LEAD

CONTENT

Table of Contents Page

IMPORTANT SAFETY INFORMATION .................................................................. 3

GETTING STARTED ............................................................................................. 7

INSTALLATION .................................................................................................. 11

OPERATION ...................................................................................................... 27

TROUBLESHOOTING ........................................................................................ 30

MAINTENANCE ................................................................................................ 32

REPAIR PARTS .................................................................................................. 35

GAS CONVERSION ......................................................................................... 23

• Shall not be installed in the occupied space of the manufactured

(mobile) home.

• Originally shipped set for Natural Gas and convertible to L.P. Propane

Gas (all parts included). See Gas Conversion on page 23.

• For potable water heating only. Not suitable for space heating.

Residential Direct Vent Water Heater with the

Flammable Vapor Igni on Resistant

Safety System

For Installa on in a Manufactured Home (Mobile Home)

2 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

COMPLETED INSTALLATION (TYPICAL)

Gas Supply

^ŚƵƚŽī

Gas Supply

Gas Control

Valve/Thermostat

Sediment Trap

Ground Joint

Union

Metal Drain Pan

Terminate the

discharge pipes

through the

ƐƚƌƵĐƚƵƌĂůŇŽŽƌŽƌ

a maximum of six

inches above a

ŇŽŽƌĚƌĂŝŶ͘

Protect discharge

pipes from

ĨƌĞĞǌŝŶŐ͘

Drain Valve

>ŝŐŚƟŶŐ/ŶƐƚƌƵĐƟŽŶƐ

T&P Discharge

Pipe

T&P Relief Valve

Expansion Tank

(connect to

cold water supply)

Cold Water

Line

Cold Water

^ŚƵƚŽī

Roof Jack / Vent

Hot Water

Line

Flue Reducer

ŽŶǀĞƌƐŝŽŶ/ŶƐƚƌƵĐƟŽŶƐ

ZĂƟŶŐWůĂƚĞ

Read and follow

Ăůů ĐĂƵƟŽŶƐ ĂŶĚ

warnings on the

water heater’s

ůĂďĞůŝŶŐ͘

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 3

SAFETY

IMPORTANT SAFETY INFORMATION

Important informa on to keep

Fill out this sec on and keep this

manual in the pocket of the water

heater for reference.

Date Installed:

Model number:

Serial number:

Maintenance performed:* Date:

This is the safety alert symbol. It is used to alert you to

poten al physical injury hazards. Obey all safety mes-

sages that follow this symbol to avoid possible property

damage, serious injury or death. Do not remove any per-

manent instruc ons, labels, or the ra ng plate from either the outside of

the water heater or on the inside of the access panels. Keep this manual

near the water heater.

DANGER

Read and follow all safety messages and instruc ons in

this manual.

DANGER indicates hazardous situa-

 on that, if not avoided, will result

in death or serious injury.

WARNING

WARNING indicates a hazardous

situa on that, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION indicates a hazardous

situa on that, if not avoided, could

result in minor or moderate injury.

NOTICE

NOTICE indicates prac ces not

related to physical injury.

WARNING! If the informa on in these instruc ons is not followed exactly,

a ﬁ re or explosion may result causing property damage, personal injury or

death. Do not store or use gasoline or other ﬂ ammable vapors and liquids in

the vicinity of this or any other appliance.

An odorant is added by the gas supplier to the gas used by this water heater.

This odorant may fade over an extended period of  me. Do not depend upon

this odorant as an indica on of leaking gas. We recommend installing a fuel gas

and carbon monoxide detector.

*Drain and ﬂ ush tank and remove

and inspect anode rod a er ﬁ rst six

months of opera on and at least

annually therea er. Operate the

Temperature and Pressure Relief Valve

(T&P) annually and inspect T&P valve

every 2-4 years (see the label on the

T&P valve for maintenance schedule).

See the Maintenance sec on for more

informa on about maintaining this

water heater.

4 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

SAFETY

IMPORTANT SAFETY INFORMATION

o reduce the risk of property

damage, serious injury or death,

read and follow the precau ons below,

all labels on the water heater, and

the safety messages and instruc ons

throughout this manual.

RISKS DURING

INSTALLATION AND

MAINTENANCE

Li ing Risk

WARNING! The

water heater is heavy.

Follow these

precau ons to reduce

the risk of property damage, injuries

from li ing or impact injuries from

dropping the water heater.

• Use at least two people to li the

water heater.

• Be sure you both have a good grip

before li ing.

• Use an appliance dolly or hand

truck to move the water heater.

Explosion Risk

WARNING! Read the water heater’s

ra ng plate to determine the type of

gas required. Failure to follow these

instruc ons can result in serious injury

or death from explosion, ﬁ re or

carbon monoxide poisoning.

• Do not connect a natural gas water

heater to an L.P. gas supply.

• Do not connect an L.P. gas water

heater to a natural gas supply.

• Use a new CSA approved gas

supply line.

• Install a shut-oﬀ valve on the gas

supply line.

• Do not use this water heater

with any gas other than the one

listed on the original ra ng plate

unless the water heater has been

properly converted. Refer to the

Gas Conversion sec on of this

manual to convert from one gas

type to another. See page 23.

Gas Pressure

WARNING! The gas supply pressure

must not exceed the maximum supply

pressure as stated on the water

heater’s ra ng plate. The minimum

supply pressure is for the purpose of

input adjustment. L.P. gas supply

pressure must not exceed 13” water

column. Have a qualiﬁ ed person

(licensed plumber, gas company

personnel, or authorized service

technician) check for proper L.P. gas

pressure. L.P. gas pressures exceeding

13” water column can result in serious

injury or death from explosion or ﬁ re.

RISKS DURING

OPERATION

Scalding Risk

This water heater

can make water hot

enough to cause severe burns instantly,

resul ng in severe injury or death.

• Feel water before bathing or

showering.

• To reduce the risk of scalding,

install Thermosta c Mixing Valves

(temperature limi ng valves) at

each point-of-use. These valves

automa cally mix hot and cold

water to limit the temperature at

the tap. Follow manufacturer’s

instruc ons for installa on and

adjustment of the valves.

• The gas control valve on this water

heater has been factory set to its

lowest se ng to reduce the risk

of scalding. Higher temperatures

increase the risk of scalding, but

even at 120°F, hot water can

scald. If you choose a higher

temperature se ng, Thermosta c

Mixing Valves located at each

point-of-use are par cularly

important to help avoid scalding.

Table 1

Temperature

Time to Produce

a Serious Burn

120°F (49°C) More than 5 minutes

125°F (52°C) 1½ to 2 minutes

130°F (54°C) About 30 seconds

135°F (57°C) About 10 seconds

140°F (60°C) Less than 5 seconds

145°F (63°C) Less than 3 seconds

150°F (66°C) About 1½ seconds

155°F (68°C) About 1 second

For informa on about changing the

factory temperature se ng, refer

to the “Adjus ng the Temperature”

sec on in this manual (page 29).

Even if you set the water heater’s gas

control valve to a low se ng, higher

water temperatures may occur in

certain circumstances:

• In some cases, repeated small draws

of water can cause the hot and cold

water in the tank to “stack” in layers.

If this happens, the water can be as

much as thirty degrees ho er than

the gas control valve se ng. This

temperature varia on is the result

of your usage pa ern and is not a

malfunc on.

• Water temperature will be ho er if

someone adjusted the gas control

valve to a higher se ng.

• Problems with the gas control

valve or other malfunc ons may

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 5

SAFETY

IMPORTANT SAFETY INFORMATION

result in higher than expected water

temperatures.

• If the water heater is in a hot

environment, the water in the

tank can become as hot as the

surrounding air, regardless of the

temperature se ng.

• If the water supplied to the water

heater is pre-heated (for example,

by a solar system) the temperature

in the tank may be higher than the

water heater’s temperature se ng.

• Should overhea ng occur or the

burner fail to shut oﬀ , turn oﬀ the

manual gas supply valve to the water

heater and call a qualiﬁ ed person.

To reduce the risk of unusually hot

water reaching the ﬁ xtures in the

house, install Thermosta c Mixing

Valves at each point-of-use.

If anyone in your home is at par cular

risk of scalding (for example, the elderly,

children, or people with disabili es)

or if there is a local code or state law

requiring a certain water temperature

at the hot water tap, these precau ons

are par cularly important.

According to a na onal standard (ASSE

1070) and many local plumbing codes,

the water heater’s gas control valve

should not be used as the sole means

to regulate water temperature and

avoid scalds.

Properly adjusted Thermosta c Mixing

Valves installed at each point-of-use

allow you to set the tank temperature

to a higher se ng without increasing

risk of scalds. A higher temperature

se ng allows the tank to provide

much more hot water and can help

provide proper water temperatures

for appliances such as dishwashers

and washing machines. Higher tank

temperatures (140°F) also kill bacteria

that cause a condi on known as “smelly

water” and can reduce the levels

of bacteria that cause water-borne

diseases.

Water Contamina on Risk

Do not use chemicals that could

contaminate the potable water supply.

Do not use piping that has been treated

with chromates, boiler seal, or other

chemicals.

Fire Risk

This water heater is

equipped with a

Flammable Vapor Igni on

Resistance (FVIR) system.

FVIR is designed to reduce the risk of

ﬂ ammable vapor-related ﬁ res. FVIR

makes this product more sensi ve to

installa on errors or improper

installa on environments. The FVIR

system will not prevent a possible ﬁ re/

explosion if the igniter is depressed and

ﬂ ammable vapors have accumulated in

the combus on chamber with the pilot

light oﬀ .

Do not a empt to light this appliance,

or depress the igniter bu on, if you

suspect ﬂ ammable vapors have

accumulated inside or outside the

appliance. Immediately call a qualiﬁ ed

person to inspect the appliance. Water

heaters subjected to a ﬂ ammable vapors

incident will show a discolora on on the

ﬂ ame arrestor and require replacement

of the en re water heater. Improper

installa on or an inadequate air supply

can also cause the FVIR system to disable

the water heater.

To reduce the risk of a ﬁ re that could

result in property damage, or serious

injury or death:

• Do not store things that can burn

easily such as paper or clothes next

to the water heater.

• Do not store or use gasoline or other

ﬂ ammable substances in the vicinity

of this or any other appliance.

• Keep the water heater from

becoming wet. Immediately shut

the water heater oﬀ and have it

inspected by a qualiﬁ ed person if you

ﬁ nd that the wiring, thermostat(s)

or surrounding insula on have been

exposed to water in any way (e.g.,

leaks from plumbing, leaks from

the water heater itself can damage

property and could cause a ﬁ re risk).

If the water heater is subjected to

ﬂ ood condi ons or the thermostat(s)

have been submerged in water,

the en re water heater must be

replaced.

• Replace the water heater’s viewport

if glass is missing or damaged. Repair

the combus on chamber door seals

if damaged.

Explosion Risk

High temperatures and

pressures in the water

heater tank can cause an explosion

resul ng in property damage, serious

injury or death. A new Temperature

and Pressure (T&P) Relief Valve is

included with your water heater to

reduce risk of explosion by discharging

hot water. Addi onal temperature and

pressure protec ve equipment may be

required by local codes.

A na onally recognized tes ng

laboratory maintains periodic

inspec on of the valve produc on

process and cer ﬁ es that it meets the

requirements for Relief Valves for Hot

Water Supply Systems, ANSI Z21.22.

The T&P Relief Valve’s relief pressure

must not exceed the working pressure

ra ng of the water heater as stated on

the ra ng plate.

6 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

SAFETY

IMPORTANT SAFETY INFORMATION

Maintain the T&P Relief Valve properly.

Follow the maintenance instruc ons

provided by the manufacturer of the

T&P Relief Valve (label a ached to T&P

Relief Valve). An explosion could occur

if the T&P Relief Valve or discharge

pipe is blocked. Do not cap or plug the

T&P Relief Valve or discharge pipe.

Fire and Explosion Risk if Hot Water is

Not Used for Two Weeks or More.

CAUTION! Hydrogen gas builds up

in a hot water system when it is not

used for a long period (two weeks or

more). Hydrogen gas is extremely

ﬂ ammable. If the hot water system

has not been used for two weeks or

more, open a hot water faucet for

several minutes at the kitchen sink

before using any electrical appliances

connected to the hot water system. If

hydrogen is present there will

probably be an unusual sound such as

“air” escaping through the pipe as hot

water begins to ﬂ ow. Do not smoke or

have an open ﬂ ame or other igni on

source near the faucet while it is

open.

Carbon Monoxide Risk

WARNING! This water heater

operates by burning gas.

Carbon monoxide is a

colorless, odorless

gas that is a by-

product of burning of

fuels such as coal,

wood, charcoal, oil,

kerosene, propane, and natural gas.

Breathing excessive and abnormal

amounts of carbon monoxide can

cause carbon monoxide poisoning,

resul ng in serious injury or death.

This water heater must be supplied

with adequate combus on air and

must be properly vented to the

outdoors. Have a qualiﬁ ed person

(licensed plumber, authorized gas

company personnel, or authorized

service technician) install the ven ng

system using these installa on

instruc ons as well as those provided

by the roof jack manufacturer.

• Install a fuel gas and carbon

monoxide detector in the living

areas of your home.

• Do not install this water heater

in the occupied space of the

manufactured (mobile) home.

• Failure to follow these instruc ons

can result in serious injury or

death from carbon monoxide

poisoning.

Burn Risk

This water heater’s

ven ng system can

become hot enough to burn. Do not

touch the ven ng system while water

heater is on, or un l the water heater

is turned oﬀ and the ven ng allowed

to cool.

Installa on Accessories

Figure 1: Gas Water Heater Hook-Up Kit

Figure 2: Install a Pressure Reducing Valve set to

50 to 60 PSI.

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 7

GETTING STARTED

Review all of the instruc ons

before you begin work.

Improper installa on can

damage the water heater, your home

and other property, and can present

risks of serious injury or death.

This water heater is design-

cer ﬁ ed by CSA Interna onal

as a Category I, non-direct

vented water heater which takes its

combus on air through openings in an

enclosure. (See Enclosure InstallaƟ on

Requirements.) This water heater must

be installed according to all local and

state codes or, in the absence of local

and state codes, the “Na onal Fuel Gas

Code”, ANSI Z223.1(NFPA 54)-current

edi on. This is available from the

following:

CSA America, Inc.

8501 East Pleasant Valley Road

Cleveland, OH 44131

Na onal Fire Protec on Associa on

1 Ba erymarch Park

Quincy, MA 02269

Manufactured home manufacturers:

The installa on must conform to The

Manufactured Home ConstrucƟ on

and Safety Standard, Title 24 CFR, Part

3280. This standard is available through

the U.S. Department of Housing and

Urban Development (HUD), 451 7th

Street S.W., Washington D.C. 20410.

Check with local code oﬃ cials about

codes governing this installa on. Have

your installa on inspected by a code

oﬃ cial to ensure the installa on meets

all local codes.

NOTICE: If you lack the necessary skills

required to properly install this water

heater, or you have diﬃ culty following

the instruc ons, you should not proceed

but have a qualiﬁ ed person perform the

installa on of this water heater.

Massachuse s code requires this water

heater to be installed in accordance

with Massachuse s 248-CMR 2.00 and

248-CMR 5.00: State Plumbing Code.

Other local and state authori es may

have similar requirements or other

codes applicable to the installa on of

this water heater.

NOTICE: The state of California re-

quires bracing, anchoring, or strapping

the water heater to avoid its moving

during an earthquake. Contact local

u li es for code requirements in your

area, visit h p://www.dsa.dgs.ca.gov,

or call 1-916-445-8100 and request

instruc ons. Other loca ons may have

similar requirements. Check with your

local and state authori es.

Before you start, be sure you

have the following tools and

supplies:

• Common plumbing tools

(depending on what type of water

pipes you have).

• Teﬂ on® tape or pipe joint

compound approved for potable

water.

• For homes with copper pipes, you

may purchase a Gas Water Heater

Hook-Up Kit (available at your local

hardware store ) with compression

ﬁ  ngs that don’t require soldering.

This kit includes two 12” ﬂ ex water

lines, two compression ﬁ  ngs, an

18” ﬂ exible gas line, two nipples,

and Teﬂ on® tape.

• For homes with plas c pipe, use

threaded connectors suitable for

the speciﬁ c type of plas c pipe

used: CPVC or PEX (cross-linked

polyethylene). Do not use PVC

pipe.

• Non-corrosive gas leak detec on

solu on made from hand

dishwashing soap mixed with water

(1 part soap to 15 parts water)

or children’s soap bubbles and a

small, so -bristled brush.

• An appliance dolly or hand truck to

move the water heater.

Recommended Accessories:

• A metal drain pan.

• Automa c water leak detec on

and shut-oﬀ device.

• Pressure Reducing Valve.

• Thermal Expansion Tank.

• Thermosta c Mixing Valves at each

point-of-use.

• Fuel gas and carbon monoxide

detector.

Review the following

requirements and

recommenda ons before

installing the water heater.

Vent System

Requirements

WARNING! Carbon Monoxide

Hazard. This water heater must be

supplied with adequate air and vented

to outdoors. The vent system must be

installed by a qualiﬁ ed person.

Examples of a qualiﬁ ed person include

gas technicians, authorized gas

company personnel, and authorized

service technicians. Failure to properly

vent the water heater can result in

severe injury or death from carbon

monoxide poisoning.

To reduce the risk of carbon monoxide

poisoning, install a fuel gas and carbon

monoxide detector. Install and maintain

the detector in accordance with the

manufacturer’s instruc ons and local

codes.

This water heater uses a direct vented,

8 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

GETTING STARTED

Figure 3: Enclosure Configurations

GETTING STARTED

single-pipe vent system to remove

exhaust gases created by the burning

of fossil fuels. Air for combus on

is ducted in from the outside (see

Enclosure InstallaƟ on Requirements).

This water heater must be properly

vented for the removal of exhaust

gases to the outside atmosphere.

Correct installa on of the vent pipe

system is mandatory for the proper

and eﬃ cient opera on of this water

heater and is an important factor in the

life of the unit.

The vent pipe must be installed

according to all local and state codes

or, in the absence of local and state

codes, the NaƟ onal Fuel Gas Code,

ANSI Z223.1 (NFPA 54)-current edi on.

Manufactured home manufacturers

must conform with The Manufactured

Home ConstrucƟ on and Safety

Standard, Title 24 CFR, Part 3280.

The vent pipe installa on must not

be obstructed so as to prevent the

removal of exhaust gases to the

outside atmosphere.

IMPORTANT:

• Do not use a vent damper anywhere

in the vent system of this water

heater.

• DO not common vent this water

heater with any other appliance.

• This water heater must have a

properly-installed dra hood and be

connected to a listed roof jack that

terminates to the outdoors. The

roof jack vent pipe must be secured

to the ﬂ ue reducer with sheet metal

screws. (Roof jack not furnished.)

The following roof jack models are

cer ﬁ ed for use with this water heater

and are available from your water

heater supplier:

Roof Jack for roof pitch of 7-12 or less:

TABLE 2

KIT NUMBER MAXIMUM LENGTH

BETWEEN ROOF

AND CEILING

100285331 12”

100285333 32”

100285412 60”

100285414 95”

Install the roof jack according to its

manufacturer’s instruc ons.

AIR INTAKE

OPENING

MANUFACTURED HOME

OUTER PIPE OF

ROOF JACK:

0 IN. (0 CM)

MIN. CLEARANCE

DIRECT VENT

WATER HEATER

3” (76 mm) PVC PIPING - 30 AND 40 GAL.

4” (102 mm) PVC PIPING - 50 GAL.

SUPPORT PIPE AT

3-1/2 FT. (1.07 m) INTERVALS

BASEMENT OR

CRAWL SPACE

* VENT CAP MUST BE LOCATED A MINIMUM OF 12” (30.48 cm)

ABOVE GROUND OR ANTICIPATED SNOW LEVEL.

12” MIN.

45° ELBOW

METHOD 1:

AIR INTAKE - MINIMUM OPENING SIZE

METHOD 2:

AIR INTAKE - BASEMENT OR CRAWLSPACE

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 9

GETTING STARTED

Enclosure Installa on

Requirements

WARNING! Do not store or use

ﬂ ammable materials, vapors, or liquids

in the water heater enclosure. Do not

use the enclosure as a storage area.

Whether replacing an old water heater

or pu ng the water heater in a new

loca on, the following cri cal points

must be observed.

This manufactured home gas-

ﬁ red water heater is for use in a

manufactured home. You should

carefully choose an indoor loca on

for the new water heater, because

the placement is a very important

considera on for the safety of your

occupants in the building and for the

most economical use of the appliance.

This water heater is for use only in a

manufactured home and not intended

for outdoor installa on.

NOTICE: This water heater has been

designed and cer ﬁ ed as a direct vent

(sealed combus on) unit and no dra

diverter is to be used.

Minimum clearances between the

water heater and combus ble surfaces

are stated on the label adjacent to

the gas control valve/thermostat. The

water heater is cer ﬁ ed for installa on

on a combus ble ﬂ oor. Minimum vent

clearances: 6” (15.2 cm). Provide 24”

(61 cm) front clearance for servicing

and adequate clearance between the

jacket top and ceiling for servicing the

ﬂ ue area. Roof jack: surface of outer

pipe has a minimum clearance of 0” (0

cm).

The combus on and ven la on air ﬂ ow

must not be obstructed.

Combus on air shall not be supplied

from occupied spaces. Instead,

combus on air must be supplied from

outside the manufactured home by

way of the furnished air intake duct

assembly. The air intake duct assembly

is 3” (7.62 cm) in diameter for 30 and

40 Gallon models or 4” (10.2 cm) in

diameter for 50 Gallon models.

The following methods may be used

to provide suﬃ cient combus on and

ven la on air to the water heater when

it is installed in the enclosure. See

Figure 3: Enclosure Conﬁ gura ons.

IMPORTANT:

A 3-1/2” (8.89 cm) diameter ﬂ oor

opening beneath the water heater is

required to accommodate the air intake

duct assembly for 30 and 40 Gallon

models. A 4-1/2” (11.43 cm) diameter

ﬂ oor opening is required beneath the

water heater for 50 Gallon models. The

weight of the water heater itself seals

the water heater to the air intake duct

assembly.

Method 1

When a manufactured home is skirted,

an air intake opening with a minimum

free area of 32 square inches (206.45

cm²) must be provided in the skirt. If

the opening is covered by louvers or

screen, the total free area must be 32

square inches (206.45 cm²). Other gas

ﬁ red appliance in the home will require

addi onal free air openings; consult

these manufacturers for correct sizing.

See Figure 3.

Method 2

If the manufactured home is installed

over a basement or crawlspace,

combus on air must be supplied from

outside the manufactured home. The

combus on air intake piping can be

3” (76 mm) PVC for 30 and 40 gallon

models and 4” (102 mm) PVC for 50

Gallon models. The air intake piping

cannot exceed the lengths shown in

Table 3 (page 19), including ver cal

and horizontal runs, or have more than

3 elbows. All horizontal runs require

adequate support at 3-1/2 foot (1.07 m)

intervals. See Figure 3

IMPORTANT: The drain pan must not

cover any por on of the air intake

opening in the ﬂ oor.

Also, if the manufactured home is

skirted, an air intake opening with a

minimum free area of 32 square inches

must be provided in the skirt. Other

gas ﬁ red appliances in the home may

require addi onal free air openings.

Consult the manufacturers for correct

sizing.

IMPORTANT:

• The water heater must be secured

with brackets/straps as described in

Securing the Water Heater, page 16.

• A discharge line must be installed

as described in the typical

installa on graphic. See COMPLETED

INSTALLATION (TYPICAL), page 2.

• There must be adequate space

(clearances) for periodic servicing

(e.g., a minimum of 24 inches of

front clearance). The installa on

must allow a minimum clearance

from combus ble surfaces as stated

on the ra ng plate.

• It is recommended that the water

heater be installed in a metal drain

pan. The drain pan should be piped

to an adequate drain or through the

structural ﬂ oor of the enclosure.

• Do not obstruct the combus on and

ven la on air openings.

• If the water heater is installed directly

on carpe ng, it shall be installed on

10 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

GETTING STARTED

a metal or wood panel extending

beyond the full width and depth

of the water heater by at least 3 in

(76.2mm) in any direc on. If the

water heater is installed in an alcove

or closet, the en re ﬂ oor shall be

covered by the aforestated panel.

• Prevent the water lines and

discharge lines from freezing.

General Requirements

• The water heater shall not be

installed in the occupied space of

the manufactured (mobile) home.

• Inspect and maintain your water

heater in accordance with this

manual’s instruc ons. Inspect the

drain pan, pipes, and surrounding

area regularly and ﬁ x any leaks

found.

Gas Piping

Requirements

Gas piping must be installed according

to local and state codes or, in the

absence of local and state codes,

the NaƟ onal Fuel Gas Code, ANSI

Z223.1(NFPA 54)-current edi on.

Manufactured home manufacturers

must conform with The Manufactured

Home ConstrucƟ on and Safety

Standard, Title 24 CFR, Part 3280.

NOTICE: When installing gas piping,

apply pipe joint compound or Teﬂ on®

tape approved for fuel gases.

Figure 4: Gas Piping

1. Install a readily accessible manual

shut-oﬀ valve in the gas supply

line as recommended by the local

u lity. Know the loca on of this

valve and how to turn oﬀ the gas to

this unit.

2. Install a Sediment Trap as shown

in the Gas Piping ﬁ gure

(page 10). The Sediment Trap

must be no less than three inches

long for the accumula on of

dirt, foreign material, and water

droplets.

3. Install a ground joint union

between the gas control valve and

the manual gas shut-oﬀ valve. This

is to allow easy removal of the gas

control valve.

4. Turn the gas supply on and check

for leaks. Use a small, so -

bristled brush to apply a hand

dishwashing soap and water

mixture (1 part soap to 15 parts

water) or children’s soap bubbles

to all connec on points of the gas

piping. Saturate all the connec ons

and check for gas leaks (which will

appear as small bubbles). If any

leaks are detected,  ghten the

appropriate connec on(s) and

re-check.

Gas Pressure

NOTICE: When tes ng gas pipes with

a test pressure of more than ½ psi (3.5

kPa), disconnect the gas line at the

manual shut oﬀ valve and cap the gas

line. Do not subject the water heater’s

gas control valve or manual shut oﬀ

valve to more than ½ psi (3.5 kPa)

pressure for any reason. If you are

pressure tes ng the gas line with test

pressure of ½ psi (3.5 kPa) or less, you

may isolate the water heater from the

gas line by closing the manual shut oﬀ

valve.

LP Gas Only

Liqueﬁ ed petroleum gas is over 50%

heavier than air and in the occurrence

of a leak in the system, the gas will

se le at ﬂ oor level. Basements, crawl

spaces, skirted areas under mobile

homes (even when ven lated), closets

and areas below ground level will serve

as pockets for the accumula on of gas.

Before ligh ng an L.P. gas water heater,

smell all around the appliance at ﬂ oor

level. If you smell gas, do not a empt

to light the water heater. Follow the

instruc ons as given in the warning on

the front cover of this manual.

When your L.P. tank runs out of fuel,

turn oﬀ the gas at all gas appliances

including pilot lights. A er the tank is

reﬁ lled, all appliances must be re-lit

according to their manufacturer’s

instruc ons.

WARNING! Have a qualiﬁ ed person

make sure that the L.P. gas opera ng

pressure does not exceed 13” water

column. Examples of a qualiﬁ ed

person include: licensed plumbers,

authorized gas company personnel,

and authorized service personnel.

Failure to do so can result in death,

explosion, or ﬁ re.

GETTING STARTED

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 11

INSTALLATION

Step 1:

✓

Verify that your

home is equipped

and up-to-date for

proper opera on

Installing a new water heater is the

perfect  me to examine your home’s

plumbing system and make sure the

system is up to current code standards.

There have likely been plumbing code

changes since the old water heater

was installed. We recommend install-

ing the following accessories and any

other needed changes to bring your

home up to the latest code require-

ments. Upda ng your plumbing system

can help extend the life of your water

heater, avoid damage to your home

and property, and reduce the risk of

serious injuries or death. Inspect your

home and install any devices you need

to comply with current codes and as-

sure that your new water heater per-

forms at its best. Check with your local

plumbing oﬃ cial for more informa on.

✓

Water pressure

Most codes allow a maximum

incoming water pressure of 80 psi

(we recommend a working pressure

no higher than 50-60 psi). Check your

home’s water pressure with a pressure

gauge and adjust if necessary. High

water pressure can damage the water

heater, piping, and other appliances.

HOW: Purchase an inexpensive water

pressure gauge at your local plumbing

supplier. Connect the water pres-

sure gauge to an outside faucet and

measure the maximum water pressure

experienced throughout a 24-hour

period (highest water pressures o en

occur at night).

Figure 5: Use a Water Pressure Gauge to make

sure your home’s water pressure is not too high.

To adjust your home’s water pressure:

Locate your home’s Pressure Reduc-

ing Valve (PRV) on the main incoming

(cold) water supply line and adjust the

water pressure control to between 50

and 60 psi. If your home does not have

a Pressure Reducing Valve, install a

PRV on the home’s main water supply

line and set it to between 50 and 60

psi. Pressure Reducing Valves are avail-

able at your local plumbing supplier.

BACKGROUND: Over the years, many

u li es have increased water sup-

ply pressures so they can serve more

homes. In some homes today, pres-

sures can exceed 100 psi. High water

pressures can damage water heaters,

causing premature leaks. If you have

replaced toilet valves, had a water

heater leak, or had to repair applianc-

es connected to the plumbing system,

pay par cular a en on to your home’s

water pressure. When purchasing a

PRV, make sure the PRV has a built-in

bypass.

✓

Water pressure

increase caused by

thermal expansion

Verify that you have a properly sized

Thermal Expansion Tank. We recom-

mend installing an expansion tank if

your home does not have one. Plumb-

ing codes require a properly pressur-

ized, properly sized Thermal Expansion

Tank in almost all homes.

Figure 6: A Thermal Expansion Tank helps protect

the home’s plumbing system from pressure

spikes.

HOW: Connect the Thermal Expan-

sion Tank (available at most hardware

stores.) to the cold water supply line

near the water heater. The expansion

tank contains a bladder and an air

charge. To work properly, the Thermal

Expansion Tank must be sized accord-

ing to the water heater’s tank capacity

and pressurized to match the home’s

incoming water pressure. Refer to the

instruc ons provided with the Thermal

Expansion Tank for installa on details.

BACKGROUND: Water expands when

heated, and the increased volume

of water must have a place to go, or

thermal expansion will cause large

increases in water pressure (despite

12 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

INSTALLATION

the use of a Pressure Reducing Valve

in the home’s main water supply line).

The Safe Drinking Water Act of 1974

requires the use of backﬂ ow preven-

ters and check valves to restrict water

from your home reentering the public

water system. Backﬂ ow preventers

are o en installed in water meters

and may not be readily visible. As

a result, most all plumbing systems

today are now “closed,” and almost all

homes now need a Thermal Expan-

sion Tank.

A Thermal Expansion Tank is a prac -

cal and inexpensive way to help avoid

damage to the water heater, washing

machine, dishwasher, ice maker, and

even toilet valves. If your toilet oc-

casionally runs for no apparent reason

(usually brieﬂ y at night), that may be

due to thermal expansion increasing

the water pressure temporarily.

✓

Water Pipe and

Tank Leaks

Metal Drain Pan

Piped to Drain

Figure 7: A metal drain pan piped through the

floor to the outside (or to an adequate drain)

can help protect flooring from leaks and drips.

Leaks from plumbing pipes or from

the water heater itself can damage

property and could cause a ﬁ re risk.

• Install an automa c leak detec on

and shutoﬀ device (available at your

local plumbing supplier ). These de-

vices can detect water leaks and can

shut oﬀ the water heater’s water

supply if a leak occurs.

• Install a metal drain pan ( available at

your local plumbing supplier) under

the water heater to catch conden-

sa on or leaks from the piping

connec ons or tank. Most codes

require, and we recommend, install-

ing the water heater in a metal drain

pan that is piped through the ﬂ oor

to the outside or to an adequate

drain. The drain pan must be at least

two inches wider than the diameter

of the water heater. Install the drain

pan so the water level would be lim-

ited to a maximum depth of 1-3/4”.

The pan must not restrict air ﬂ ow to

the burner.

✓

Water

Temperature

Regula on

Install Thermosta c Mixing Valves to

regulate the temperature of the water

supplied to each point-of-use (for

example, kitchen sink, bathroom sink,

bath, shower). Install and adjust the

mixing valve according to its manufac-

turer’s instruc ons.

WARNING! Even if the water

heater’s thermostat is set to a

rela vely low temperature, hot water

can scald. Install Thermosta c Mixing

Valves at each point-of-use to reduce

the risk of scalding.

Figure 8: Thermostatic Mixing Valves installed at

each point-of-use can help avoid scalding

BACKGROUND: A Thermosta c Mix-

ing Valve, installed at each point-

of-use, mixes hot water from the

water heater with cold water to more

precisely regulate the temperature of

hot water supplied to ﬁ xtures. If you

aren’t sure if your plumbing system is

equipped with properly installed and

adjusted Thermosta c Mixing Valves

at each point where hot water is used,

contact a qualiﬁ ed person.

Step 2:

Ensure that the

enclosure is prepared

for installa on

WARNING! Do not store or use

ﬂ ammable materials, vapors, or

liquids in the same loca on where this

water heater is installed.

Before installing your water heater,

ensure that the water heater can be:

• Installed in an enclosure that

meets the requirements

outlined in Enclosure InstallaƟ on

Requirements (page 9).

• Protected from freezing.

• Set in a metal drain pan piped to

an adequate drain.

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 13

INSTALLATION

• Provided with adequate space

(clearances) for periodic servicing.

(There must be a minimum of 24

inches of front clearance.)

• Installed with a minimum clear-

ance from combus ble surfaces as

stated on the ra ng plate.

• Installed on a ﬂ oor that can sup-

port the weight of a water heater

full of water.

• A 3-1/2” (8.89 cm) diameter ﬂ oor

opening beneath the water heater

is required to accommodate the

air intake duct assembly for 30 and

40 Gallon models. A 4-1/2” (11.43

cm) diameter ﬂ oor opening is

required beneath the water heater

for 50 Gallon models. The weight

of the water heater itself seals the

water heater to the air intake duct

assembly.

NOTICE: The state of California requires

bracing, anchoring, or strapping the

water heater to avoid its moving during

an earthquake. Contact local utilities

for code requirements in your area,

visit http://www.dsa.dgs.ca.gov, or call

1-916-445-8100 and request instruc-

tions. Other locations may have similar

requirements. Check with your local and

state authorities. See also Securing the

Water Heater (page 16).

Step 3:

Removing the old

water heater

Read each installa on step and

decide if you have the necessary

skills to install the water heater.

Only proceed if you are comfortable you

can safely perform the work. If you are

not sure, have a qualiﬁ ed person perform

the installa on.

On the old water heater, turn

the control knob on the gas

control valve to the

OFF posi on.

Figure 9: Turn gas control/temperature knob OFF.

Turn the manual gas valve for

the water heater’s supply line

OFF.

Open a hot water faucet and

let the hot water run un l it is

cool. (This may take 10

minutes or longer.)

Figure 10: Let the hot water run until it is cool.

WARNING! Be sure the water runs

cool before draining the tank to reduce

the risk of scalding.

Connect a garden hose to the

drain valve and place the

other end of the hose in a

drain, outside, or in buckets. (Sedi-

ment in the bo om of the tank may

clog the valve and prevent it from

draining. If you can’t get the tank to

drain, contact a qualiﬁ ed person.)

Turn the cold water supply

valve OFF.

Figure 11: Cold water supply in off position.

Using a standard ﬂ at-blade

screwdriver, open the drain

valve. Sediment build up in

the bo om of the water heater may

hinder or prevent draining.

Figure 12: Draining the old water heater.

Also open a hot water faucet

to help the water in the tank

drain faster.

When the tank is empty,

disconnect the Temperature &

Pressure (T&P) Relief Valve

discharge pipe. You may be able to

reuse the discharge pipe, but do not

reuse the old T&P Relief Valve. A new

T&P Relief Valve comes with your new

water heater.

14 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

INSTALLATION

Figure 13: Removing the T&P Relief Valve

discharge pipe.

Allow the vent pipe (roof

jack) and dra hood to cool.

Once cooled, disconnect the

vent pipe from the dra hood. You

may need to support the vent pipe

un l the new water heater is in place.

Figure 14: Disconnect the vent pipe (roof jack)

from the draft hood.

Disconnect the water pipes.

Many water pipes are

connected by a threaded

union which can be disconnected with

wrenches. If you must cut the water

pipes, cut the pipes close to the water

heater’s inlet and outlet connec ons,

leaving the water pipes as long as

possible. If necessary, you can make

them shorter later when you install the

new water heater.

Conﬁ rm the manual gas valve

for the water heater’s supply

line is turned oﬀ . Disconnect

the gas line from the water heater’s

gas control valve and cap it.

Remove the old water heater.

Use an appliance dolly or

hand truck to move the water

heater.

WARNING! Use two or more

people to remove or install a water

heater. Failure to do so can result in

back or other injury.

Step 4:

Installing the New

Water Heater

Completely read all instruc-

 ons before beginning. If you

are not sure you can safely

complete the installa on, seek assis-

tance from any of the following sources:

• Schedule an appointment with

a qualiﬁ ed person to install your

water heater.

• Contact the manufacturer listed on the

water heater’s ra ng plate .

Locate the posi on of the

3-1/2” (8.9 cm) or 4-1/2”

(11.4 cm) hole to be cut in the

ﬂ oor, see Figures 15 and 16.

METAL

DRAIN

PAN

“A” = 4-3/8” (11.11 cm) 30 GAL.

“A” = 5-3/8” (13.65 cm) 40 GAL.

“A” = 5-3/8” (13.65 cm) 50 GAL.

CENTERLINE

OF WATER

HEATER

3-1/2” (8.89cm) DIA. HOLE

(30 & 40 GALLON)

4-1/2” (11.43cm) DIA. HOLE

(50 GALLON)

APPLY 4” (10.2 cm) OR

5” (12.7 cm) CIRCLE OF

SILICONE AROUND THE

BOTTOM OF PLATE

FOR PROPER WATER

TIGHT SEALING

AFTER ADJUSTING LENGTH OF DUCT

ASSEMBLY AS SHOWN ABOVE, CAULK

ALL AROUND PIPING WITH RTV SILICON

SEALANT FOR AIR TIGHT SEAL BEFORE

INSTALLING IN FLOOR CAVITY.

ALTERNATIVE: USE 2” (5 cm) WIDE BAND

OF .002 ALUMINUM TAPE.

2-1/2” (6.35 cm) MIN.

BOTTOM OF FLOOR

“A”

SCREWS (2)

Figure 15: Air Intake Duct Sizing Dimensions

Set the water heater in place

taking care not to damage the

drain pan. When installing

directly on carpet, the water heater

must be installed on a wood or metal

base that extends beyond the dimen-

sions of the water heater (width and

depth) by at least 3 inches (76.2 mm)

in any direc on. If the water heater is

installed on carpet in an alcove or

closet, the en re ﬂ oor must be covered

by a wood or metal panel.

NOTICE: Most codes require se ng

the water heater in a metal drain pan

piped to an adequate drain or external

to the structure. The drain pan helps

avoid property damage which may oc-

cur from condensa on or leaks in the

piping connec ons or tank. The drain

pan must be at least two inches wider

than the diameter of the water heater.

Install the drain pan so the water level

is limited to a maximum depth of

1-3/4”.

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 15

INSTALLATION

Verify that the water heater is

set in place properly. Check

that:

• There is adequate space to install

the T&P Relief Valve discharge

pipe and that it can be piped to a

separate drain (and not into the

drain pan).

• There is adequate access and

space around the water heater for

future maintenance.

The water heater is installed ver cally.

Figure 16: Air Intake Duct Installation - Drain Pan

CENTER

LINE OF

FLUE

GAS CONTROL VALVE/

THERMOSTAT

DIRECTION IN WHICH WATER HEATER CAN BE PLACED

WHEN INCREASED SIDE CLEARANCE IS AVAILABLE

9”(22.86 cm) MIN. -30 GAL.

10”(25.4 cm) MIN. -40 GAL.

11”(27.9 cm) MIN. -50 GAL.

9”(22.86 cm) MIN. -30 GAL.

10”(25.4 cm) MIN. -40 GAL.

11”(27.9 cm) MIN. -50 GAL.

0” MIN.

30 GAL. 13-13/32”

(34 cm) MIN.

40 GAL. 15-13/32”

(39.1 cm) MIN.

50 GAL. 16-13/32”

(41.7 cm) MIN.

2-1/2” 6.35 cm

4-13/32”(11.2 cm) - 30 GAL.

5-13/32”(13.7 cm) - 40 GAL.

5-13/32”(13.7 cm) - 50 GAL.

4”(10.16 cm) MIN. - 30 GAL.

0” MIN. - 40 & 50 GAL.

0” MIN.

BASE DIAMETER

14”(35.56 cm) MIN. 30 GAL.

16”(40.64 cm) MIN. 40 GAL.

16”(40.64 cm) MIN. 50 GAL.

JACKET DIAMETER

18”(45.72 cm) MIN. 30 GAL.

20”(50.80 cm) MIN. 40 GAL.

22”(55.88 cm) MIN. 50 GAL.

30 GAL. T&P LOC.

AIR INTAKE

4” (10.2cm) MIN.

Figure 17: Water Heater Installation - Enclosure

2-7/32” (5.59 cm)

12-13/16”

(32.54 cm)

9”

(22.86 cm)

3-13/16”

(9.68 cm)

4” (10.16 cm)

GAS CONTROL VALVE / THERMOSTAT

DIRECTION IN WHICH WATER HEATER MUST BE

PLACED WHEN MINIMUM CLEARANCES ARE USED

(30 GALLON ONLY)

0” MIN.

BASE DIA. - 14”

(35.56 cm)

JACKET DIA. - 18”

(45.72 cm)

60°

30°

TOP VIEW

Figure 18: Water Heater Installation - Enclosure Alternate Position

16 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

INSTALLATION

Insert the duct assembly as

shown in Figure 19 with lip

facing forward, and using only

nails, secure the duct assembly to

the ﬂ oor.

FRONT

APPLY 4” (10.16 cm) OR 5” (12.7 cm)

CIRCLE OF SILICONE AROUND OPENING

FOR AIR TIGHT SEAL.

Figure 19: Air Intake Duct Sizing Installation

Set the water heater in place

against the lip of the duct

assembly as shown in Figure 20.

Figure 20: Setting the Water Heater in place.

Secure the water heater to the

duct assembly using the screw

provided.

NOTICE: See pages 17 and 18 for

installing an air intake through an

outside wall when the manufactured

home is located over a basement or

crawl space.

SECURING WATER

HEATER TO THE FLOOR

AND WALL (USE

METHOD A OR B)

The water heater must be secured to

the floor and to the wall of the enclo-

sure.

METHOD A: use the three mounting

brackets and screws packaged in the

carton with the water heater. The two

small brackets are used to attach the

water heater to the floor and the one

large bracket is used to secure the

top of the water heater to the wall.

METHOD B: use metal tape also

called “plumbers tape” to secure the

water heater to the enclosure. See

the figure below as reference for

attaching the tape.

Because of installation variances,

these brackets can be located at any

points around the circumference of

the jacket. When the bracket loca-

tions are determined, use a 1/8 inch

SAE drill bit to set a pattern. Drill only

through the outer jacket of the water

heater. Then using the screws pro-

vided, secure the bracket to the water

heater, floor and wall. See Figure 21.

ONE LARGE MOUNTING

BRACKET AT TOP

TWO SMALL MOUNTING

BRACKETS AT BOTTOM

TWO STRAPS OF METAL

TAPE AT THE TOP

TWO STRAPS OF METAL

TAPE AT THE BOTTOM

METHOD A METHOD B

Figure 21: Methods to secure the water heater

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 17

INSTALLATION

MANUFACTURED

HOME INSTALLED OVER

BASEMENT OR CRAWL

SPACE - AIR INTAKE

THROUGH AN OUTSIDE

WALL

ALL 30 AND 40 GALLON MODELS

3” (76 mm) PVC Schedule 40 intake air

vent piping:

Op onal Kit No. 100109072 contains a

3” (76 mm) PVC Schedule 40-45° vent

cap with screen and two 3” (76 mm)

wall collars.

ALL 50 GALLON MODELS

4” (102 mm) PVC Schedule 40 intake air

vent piping:

Op onal Kit no. 100109073 contains a

4” (102 mm) PVC Schedule 40-45° vent

cap with screen and two 4” (102 mm)

wall collars.

ALL MODELS

1. PVC, ABS or CPVC Schedule 40

piping and ﬁ  ngs are acceptable

materials for the air intake vent

system.

2. The intake air vent system must

terminate horizontally to the

outdoors.

3. Remove the screws which a ach

the wind baﬄ e to the exis ng

metal air intake vent pipe

underneath the home. Discard the

wind baﬄ e and screws. See Figure

22.

IF ATTACHING INLET PIPING, REMOVE AND

DISCARD SCREWS AND WIND BAFFLE

Figure 22: Wind Baffle

4. A ach a 3” (76 mm) or 4” (102

mm) PVC street elbow to the metal

air intake vent using 3 sheet metal

screws. Con nue PVC piping to

outside wall and terminate with

vent cap and screen. See

Figure 23 and Table 3.

3” (76 mm) size - 30 and 40 gallon

models.

4” (102 mm) size - 50 gallon models.

See pages 13 and 14 for cementing

instructions.

SEE MAXIMUM

COMBINED

LENGTHS IN

TABLE 1.

SLOPE INLET PIPING

DOWNWARD TOWARD

VENT CAP TO PREVENT

CONDENSATION BUILDUP.

Figure 23: Inlet Air Installation

NOTICE: Vent cap must be located a

minimum of 12” (30.48 cm) above the

ground or an cipated snow level.

Table: 3

Water

Heater Gas

Vent

Dia.

Do Not

Exceed:

30 Gal NAT

3”

(76mm)

17  . (5.18 m)

length; 3 elbows

30 Gal LP

3”

(76mm)

12  . (3.66 m)

length; 3 elbows

40 Gal NAT

3”

(76mm)

30  . (9.1 m)

length; 3 elbows

40 Gal LP

3”

(76mm)

20  . (6.1 m)

length; 3 elbows

50 Gal NAT

4”

(102mm)

30  . (9.1 m)

length; 3 elbows

50 Gal LP

4”

(102mm)

30  . (9.1 m)

length; 3 elbows

5. Ver cal and horizontal runs must

be securely supported at 3-1/2 foot

(1.07 m) intervals. See Figure 20.

SLOPE INLET PIPING

DOWNWARD TOWARD

VENT CAP TO PREVENT

CONDENSATION BUILDUP.

Figure 24: Inlet Air Pipe Supports

6. The intake air vent piping can be

installed with no more than 3

elbows. See Figure 25.

Figure 25: Air Intake

18 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

INSTALLATION

CUTTING OPENING THROUGH

AN OUTSIDE WALL AND COLLAR

INSTALLATION

Determine the loca on for the opening

in the wall. For a 30 or 40 gallon

model, cut a 3-3/4” (9.5 cm) hole

through the outside wall. For a 50

Gallon model, cut a 4-3/4” (12 cm)

hole through the outside wall.

The 3” (76 mm) or 4” (102 mm) PVC,

ABS or CPVC Schedule 40 vent pipe can

be run from the water heater through

the wall or from the wall to the water

heater, whichever is most convenient.

The vent pipe must extend a minimum

of 1-1/2” (3.81 cm) through the

exterior wall. Note that the inside

collar must be slipped over the vent

piping before loca ng the pipe through

the wall. Before securing the inside

and outside collars to the wall, use

a silicone sealer between pipe and

opening to ensure a water and air  ght

seal. See Figure 26.

INSTALLATION SHOWING USE

OF PVC, ABS OR CPVC PIPE

SILICONE

SEALER

EXTERIOR WALL

SCREW SCREW

SCREW

1-1/2” (3.81cm) MIN. EXTENSION

THROUGH EXTERIOR WALL

COLLAR

SILICONE

SEALER

SCREEN

VENT CAP MUST BE

POSITIONED DOWNWARD

INLET PIPE SURFACE

MIN. CLEARANCE 0” (0cm)

Figure 26: Outside Wall Inlet Air Installation

NOTICE: Wall collars are for aesthetic

purposes and are not required for the

heater to operate.

CEMENTING PVC, ABS OR CPVC

PIPE AND FITTINGS

Read and observe all safety

informa on printed on primer, cleaner,

and cement containers.

Primer, cleaner, and cements are

extremely ﬂ ammable. They are

harmful or fatal if swallowed. The

vapors are harmful. They may irritate

eyes and skin and can be absorbed

through the skin.

Always store primer, cleaner, and

cements in cool, dry, well ven lated

places. Keep containers closed. Use

them in well ven lated areas. Wear

impervious clothing while handling.

Do not smoke, eat, or drink while

handling. Wash thoroughly a er

handling and before ea ng. Wear

eye protec on when handling. If

swallowed, drink water, do not induce

vomi ng, and call a physician or

poison control center immediately. If

inhaled, get fresh air and seek medical

a en on if ill feelings persist. In case

of eye and skin contact, immediately

ﬂ ush with plenty of water for 15

minutes and seek medical a en on if

irrita on persists. KEEP OUT OF REACH

OF CHILDREN.

All primers, cleaners, and cements

must meet all local codes and

applicable standards of the American

Society For Tes ng Materials

Standards.

Before using primers, cleaners and

cements, s r or shake, making sure

contents are liquid. Do not use if found

to be lumpy or jelly-like.

1. Cut pipe ends squarely removing all

burrs and dirt.

2. Dry ﬁ t pipe and ﬁ  ngs to be

connected for proper ﬁ t.

3. Clean pipe and ﬁ  ng with primer/

cleaner.

4. Apply a thin coat of cement to

ﬁ  ng, avoiding puddling inside.

5. Apply a liberal coat of cement to

pipe, leaving no voids.

6. QUICKLY assemble parts while

cement is ﬂ uid! If you wait too long,

recoat pipes.

7. Push pipe completely into socket

of ﬁ  ng, turning as it goes un l it

bo oms.

8. Hold pipe and ﬁ  ng together for

30 seconds. Then carefully clean

oﬀ excess with a cloth. Allow

connec ons a suﬃ cient  me to cure

before disturbing.

9. Remember that vent pipes must be

adequately and securely supported.

TABLE 4: APPROX. SETTING TIME

FOR 2-1/2” (63.5mm) TO 4” (102mm)

PIPE JOINTS

MOVEMENT

OF JOINT

COMPLETE

SET

90°F

(32.2°C)

TO 150°F

(65.6°C)

3/4HR. 8 HRS.

50°F (10°C)

TO 90°F

(32.2°C)

1 HR. 15 HRS.

0°F

(-17.77°C)

TO 50°F

(10°C)

1-1/3 HR. 18 HRS.

Residen al Gas Water Heater Use and Care Guide for Manufactured Homes • 19

INSTALLATION

ROOF JACK KIT MODELS VENT KIT- 12 INCH (100288331), VENT KIT - 32 INCH (100285333),

VENT KIT - 60 INCH (100285412) AND VENT KIT - 95 INCH (100285414)

INLET VENT: SURFACE OF PIPE HAS MINIMUM CLEARANCE OF 0” (0 CM)

VENT KIT / 95” (241.3 cm)

VENT KIT / 60”

(152.4 cm)

ADJ. 0-30.26°

MAX. PITCH 7-12

VENT KIT / 32” (81.28 cm)

VENT KIT / 12” (30.48 cm)

95” (241.3 cm)

36” (91.4 cm)

2” (5 cm) MIN.

136” (345.44 cm) MAX. 100” (254 cm) MAX.

55” (139.7 cm) MIN.

2” (5 cm) MIN. 2” (5 cm) MIN. 2” (5 cm) MIN.

40” (101.6 cm) MIN.

72” (182.88 cm) MAX.

25” (63.5 cm) MIN.

52” (132.08 cm) MAX.

18” (45.72 cm) MIN.

23” (58.42 cm) MAX.

30.26° MAX.

ROOF JACK: SURFACE OF OUTER PIPE

HAS A MINIMUM CLEARANCE OF 0” (0 CM).

60” (152.4 cm)

32” (81.28 cm)

18” (45.72 cm)

12” (30.48 cm)

Figure 27: Roof Jack Installation

TABLE 5: ROOF JACK KITS

KIT NUMBER MAXIMUM LENGTH

BETWEEN ROOF

AND CEILING

100285331 12”

100285333 32”

100285412 60”

100285414 95”

A cer ﬁ ed roof jack (vent kit) from

the manufacturer must be installed

with the water heaters covered by

this manual. Roof jack kits are ordered

separately. See Figure 27 to determine

which roof jack is needed for the

installa on.

NOTICE: Install the roof jack according

to its manufacturer’s instruc ons.

An op onal Roof jack Extension Pipe

(100108866) may be required where

local codes require the roof jack cap

(outlet) to terminate above the peak of

the roof.

NOTICE: DO NOT common vent this

water heater with any other appliance.

1. Cut a 5-1/2” (14 cm) diameter hole

through the roof and ceiling directly

in line with the ﬂ ue connec on on

top of the water heater. For a sloped

roof, the roof hole may have to be

enlarged to allow the roof jack to be

installed ver cally.

2. Telescope down the ﬂ ue pipe in the

roof jack assembly to a length that

will project at least 6” (15.24 cm)

below the ﬁ nished ceiling before

installing the roof jack assembly.

NOTICE: Flue pipe joints have silicone

seals that must remain in place. A soapy

water solu on sprayed around the seal

area will enable the ﬂ ue pipe and outer

pipe below to telescope more freely.

3. Telescope down the outer pipe of

the roof jack assembly to a length

that will project at least 2” (5 cm)

below the ﬁ nished ceiling before

installing the roof jack assembly.

See Figure 28.

INSTALLATION

20 • Residen al Gas Water Heater Use and Care Guide for Manufactured Homes

INSTALLATION

TELESCOPE

OUTER PIPE

AND FLUE

PIPE DOWN

OUTER PIPE

FLUE PIPE

Figure 28: Roof Jack Placement

4. Ease the roof jack assembly

through the roof and ceiling

openings. The roof jack ﬂ ashing

 lts up to 30.26° degrees for use

on a sloping roof.

5. Use sealant or caulk on the roof to

seal under ﬂ ashing of the roof jack

assembly. Use roof nails or screws

on wood construc on or sheet

metal screws on metal roofs (nails

and screws not provided). See

Figure 29.

USE SEALANT OR

CAULK TO SEAL

UNDER ROOF

JACK FLASHING

Figure 29: Sealing Roof Jack

6. Extend the ﬂ ue pipe downward

un l it is close to the ﬂ ue reducer.

See Figure 30.

FLUE PIPE

FLUE

REDUCER

Figure 30: Attach Flue Pipe to Vent Reducer

7. Fit the bo om opening of the pipe

over the top opening of the ﬂ ue

reducer. See Figure 31. Ensure

that there is no gap and that the

seal is complete.

8. Secure the ﬂ ue pipe to the reducer

with three (3) evenly-spaced sheet

metal screws (Figure 31). Do not

leave any open holes in the ﬂ ue

reducer or ﬂ ue pipe.

SECURE VENT WITH

THREE (3)

EVENLY -SPACED

SHEET METAL SCREWS

Figure 31: Securing the Flue to Vent Reducer

NOTICE: All joints for vent piping

between roof jack and water heater

are sealed from the manufacturer.

No addi onal sealing of vent pipe is

necessary.

Page is loading ...

State GS6-30-MDV250, GS6-40-MDV- 250, GS6-50-MDV-250 User manual

Brand: State

Model: GS6-30-MDV250, GS6-40-MDV- 250, GS6-50-MDV-250

Category: Water heaters & boilers

Type: User manual

This manual is also suitable for

Download PDF

report

State GS6-30-MDV250, GS6-40-MDV- 250, GS6-50-MDV-250 User manual

This manual is also suitable for

State GS6-30-MDV250, GS6-40-MDV- 250, GS6-50-MDV-250 User manual

Related papers

Other documents