2. TDX
  3. 730310
730310

TDX 730310 User manual

  • Hello! I've reviewed the instruction manual for the TDX bathroom heater models 730310 and 730311. This manual provides details on installation, operation, and safety precautions. The heater features multiple heating modes, a ventilation function, and safety mechanisms such as overheating protection. I'm ready to answer your questions about these devices.
  • What is the maximum power of the heater?
    Does the heater have a ventilation mode?
    What safety features does the heater have?
730310 & 730311
INSTRUCTION MANUAL
Technical parameter:
Product Name
Bathroom Heater
Rated voltage 220-240V
Model 730310 | 730311
Rated frequency 50Hz
Appliance Type Class Rated power 2035W
Degree of proteon
(when wall-mounted)
IPX0
StandardsIE C 60335-1 IEC 60335-2-30 IEC 60335-2-80
Product structure diagram
Electrical diagram
Air inlet
Air outlet
Installation
Check whether all parts are complete before using.
1 Determine the installaon locaon: When using this product on a wall, install it at the height
required by the user (the air outlet is at least 100cm from the ground, and the top air inlet is
at least 30cm from the ceiling), and it must be far away from the shower head and bathtub,
as shown in Figure 1. Show.
2 First, drill two8mm holes with a distance of 180mm on a solid wall according to the height
shown in thegure, and the holes depth is more than 35mm. Then drive the expansion tube
provided by the machine into the holes, screw on the self-tapping screw provided, and leave
a distance of 3-5mm from the top of the screw.
3 Insert the two round holes on the back of the heater into the screw heads hung on the wall,
and then move it horizontally to the le into the slot, and then move it down vercally to
complete the wall-mounted installaon of the heater.
Instructions for use
Power check before turn on
1. Whether the power cord is in good condon.
2. The power supply of the product is 220-240V AC, and the carrying capacity of the socket
should not be less than 10A, otherwise accidents may occur.
Instructions
1. Plug in the power plug, touch the power icon “ ”, and hear a beep, the heater turns on.
2. Touch the Heater I icon " " the heater will work at 1000W.
3. Touch the Heater II icon " ", the heater will work at 2000W.
4. Touch the Fan icon " ", the machine only ventilation, but the PTC heating element does
not work ,the inside motor will work at 35W.
5. While the heater II icon" " & " " working together, the heater working at max
power 2035W.
6. Touch the Power icon " " again, the heater stops working.
Safety protection
1. Overheating protection: When the use environment is abnormal or improper use causes the
internal temperature of the product to be too high, the temperature control element can
automatically cut off the power supply and the product stops working; after the whole heater
is cooled and the abnormality is eliminated, it can resume normal use;
2. After two hours of continuous operation, the heater will automatically shut down by default.
Press the power switch again to resume normal use.
Precautions
1. Before using the product, please check whether the power supply you are using meets the
requirements of the nameplate, and pay attention to the rated current of the socket above
10A.
2. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
3. Do not cover ; WARNING: In order to avoid overheating, do not cover the
heater.
4. It is forbidden to use it in high temperature, humidity, flammable, explosive, heated and
easily deformed, discolored, or deteriorated objects or in places with severe dust
5. The ambient temperature of use should not exceed 40℃, and do not use it in places that are
easy to be sucked in, such as curtains, to prevent fire. There should be no shelter within 30cm
of the top to facilitate air circulation.
6. That the heater is to be installed so that switches and other controls cannot be touched by a
person in the bath or shower.
7. The heater installation close to curtains and other combustible materials may pose a fire
hazard. It should be placed at least 50cm away from curtains and other combustible
materials.
8. It is strictly forbidden to insert thin metal wires or foreign objects into any holes in the
machine to avoid electric shock or damage.
9. It is strictly forbidden to share sockets with other high-power electrical appliances. It is
strictly prohibited to move the product directly by pulling the power cord.
10. It is forbidden to use the product against the power socket, the heater must not be located
immediately below a socket-outlet.
11. It is forbidden to use products as heat preservation and heating equipment for animals and
plants
12. This product is only suitable for indoor use, not for outdoor use.
13. When the product is in normal use or idle, it should be more than 1.5 meters away from the
fire source or flame, and avoid direct sunlight.
14. This appliance is not intended for use by persons (including children) with reduced
physical,sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
15. When using the product, in order to avoid burns, please do not let bare skin directly touch
the surface of the air outlet.
16. Do not unplug the power cord with wet hands, as there is a risk of electric shock or electric
shock.
17. When leaving or not in use for a long time, please be sure to cut off the power and unplug
the power plug.
18. Turn off the power before unplugging the plug; do not pull the power cord, but pull the
power plug, otherwise it may cause short circuit, fire, electric shock and other hazards.
19. Ensure that the fan is switched off from the supply mains before removing the guard.
Common malfunctions
Problem Possible cause of the problem Solution
Not work ●The plug is not inserted properly
●Heater damage
●Check whether the plug is
correctly inserted into the socket
●Send to repair shop for repair
Sudden shutdown
while heating
●The temperature exceeds the
threshold of the temperature limiter
●Has been working continuously for
two hours
●Use the standby unit after
cooling down
●Restart, select the corresponding
function key to work
Spare parts List
User Manual (1pcs) Screw (2 pcs) Expansion t ube (2 pcs)
Warranty
1. The heater is guaranteed for one year from the date of sale (subject to the invoice or proof of
purchase).
2. The following situaons do not belong to the scope of product " guarantees" maintenance
services, but our maintenance department will s serve you wholeheartedly (corresponding
fees will be charged):
1 Consumers are damaged due to improper use, maintenance and storage;
2 Damage caused by the disassembly of the company's designated special maintenance
department;
3 Products without valid purchase cecates or products with altered valid purchase
cecates;
4 Products that exceed the specied warranty period;
5 Products damaged due to unstable power supply voltage or beyond the normal voltage range
(198V-242V), or power cord installaon that does not conform to the naonal electrical
installaon;
6 Products damaged due to irresisble natural disasters;
7 The instruons specify products that are not suitable for use and are damaged due to
incorrect use.
/