2. American Standard
  3. 735083-400.021

American Standard 735083-400.021, 735083-400.020, Cadet 4098.100 Specification

  • Hello! I am an AI chatbot trained to assist you with the American Standard 735083-400.021 Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
M81
© 2014 AS America Inc.
Revised 3/14
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Seat: American Standard #5324.019 “Rise and
Shine” (with easy to clean lift-off hinge system)
solid plastic closed front seat with cover.
❏ Seat: American Standard #5311.012 “Laurel”
molded closed front seat with cover.
❏ Alternate Seat:
❏ Supply with Stop:
* Flushmate III tank system by Flushmate
®
Div. of Sloan Valve Co
GLENWALL
™
PRESSURE-ASSISTED
WALL-MOUNTED TOILET
VITREOUS CHINA
GLENWALL™ PRESSURE-ASSISTED TOILET
❏ 2093.100
•Vitreouschina
•Low-consumption(6.0Lpf/1.6gpf)
•Wall-mounted,back-outlettoilet
•Elongatedbowl
•Fully-glazed2"ballpasstrapway
•10"x12"watersurfacearea
•Pressure-assistedsiphonjetaction
•Side-mountedchrometriplever
•Close-coupledushometertank*
•SpeedConnect
®
tank/bowl coupling system
•Sanitarybaronbowl
❏ 3402.016Elongatedbowl
❏ 4098.100 Tank complete with coupling
components
Nominal Dimensions:
749x495x762mm
(29-1/2"x19-1/2"x30")
Fixtureonly,seatandsupplybyothers
Required working pressure range 25 psi - 80 psi
Alternate Congurations Available:
❏ 4098.700 Tank and tank cover only
with tank cover locking device
❏ 4098.800 Tank and tank cover only
with right hand trip lever
Compliance Certications -
Meets or Exceeds the Following Specications:
•ASMEA112.19.2forVitreousChinaFixtures
NOTES:
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-
FELT (WAX RING NOT RECOMMENDED)
SUGGEST1/16"CLEARANCEBETWEENFACEATWALLANDBACKOF
BOWL.
CARRIERFITTINGASREQUIREDTOBEFIGUREDANDFURNISHEDBY
OTHERS.
PROVIDESUITABLEREINFORCEMENTFORALLSUPPORTS.
SUPPLYNOTINCLUDEDWITHFIXTUREANDMUSTBEORDERED
SEPAR ATELY.
*
DIMENSIONSHOWNFORLOCATIONOFSUPPLYISSUGGESTED.
FORADDITIONALINFORMATIONREFERTOINSTALLATION
INSTRUCTIONSSUPPLIED.
IMPORTANT:Dimensionsofxturesarenominalandmayvarywithin
therangeoftolerancesestablishedbyANSIStandardA112.19.2.These
measurementsaresubjecttochangeorcancellation.Noresponsibilityis
assumed for use of superseded or voided pages.
14-3/4"
(375mm)
9
"
(229mm)
29-1/2"
(749mm)
9
"
(229mm)
18-1/2"
(470mm)
C/L OF SEAT POST HOLES
5-1/2
"
(140mm CENTERS)
7-1/2"
(191mm)
7-1/2"
(191mm)
C/L OF WASTE
OUTLET
(4) 7/8
(22mm) DIA. HOLES
SUPPLY AS
REQUIRED
*
5/8"
(16mm)
3-1/4"
(83mm)
1-1/2"
(38mm)
5-1/4"
(133mm)
3-7/8
"
(98mm)
FINISHED WALL
FIN.
FLOOR
3-1/4
"
(83mm)
3/4 (19mm)
REF.
6
"
(152mm)
8-1/2"
(216mm)
19-1/2"
(495mm)
3/4" ± 1/4"
(19mm ± 6mm)
C/L
30
"
(762mm)
OR
32
"
(813mm)
14-1/2"
(368mm)
OR
16-1/2
"
(419mm)
4-1/8"
(105mm)
OR
6-1/8
"
(156mm)
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USEABLE
BUILDING FACILITIES-CHECK LOCAL CODES.
BARRIER FREE
/