American Standard CADET RIGHT HEIGHT 2377.100 User manual

Brand: American Standard

Model: CADET RIGHT HEIGHT 2377.100

Type: User manual

M45

Revised 2/08

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen

❏ Silver ❏ Fawn Beige ❏ Black

❏ Seat: American Standard #5324.019 “Rise and

Shine” (with easy to clean lift-off hinge system)

solid plastic closed front seat with cover.

❏ Seat: American Standard #5311.012 “Laurel”

molded closed front seat with cover.

❏ Alternate Seat:

❏ Supply with Stop:

* Flushmate III tank system by Flushmate

Div. of Sloan Valve Co

CADET™ RIGHT HEIGHT 16-1/2" HEIGHT

PRESSURE-ASSISTED EL TOILET

VITREOUS CHINA

CADET™ RIGHT HEIGHT 16-1/2"

PRESSURE-ASSISTED ELONGATED TOILET

❏ 2377.100

• Vitreous china

• Low-consumption (1.6 gpf/6.0 Lpf)

• Bowl rim at 16-1/2"

• Elongated bowl

• Pressure-assisted siphon jet ush action

• Fully-glazed 2" ballpass trapway

• 10" x 12" water surface area

• Close-coupled Flushometer tank*

• Side-mounted chrome trip lever

• Speed Connect

tank/bowl coupling system

• Sanitary dam on bowl

• Two bolt caps

• 100% factory ush tested

❏ 3109.016 Bowl with two bolt caps

❏ 4098.100 Tank complete with

coupling components

Nominal Dimensions:

806 x 495 x 800mm

(31-3/4" x 19-1/2" x 31-1/2")

Fixture only, seat and supply by others

Recommended working pressure range

20 psi - 80 psi

Alternate Congurations Available:

❏ 3109.456 Elongated bowl only with slotted

rim for bedpan holding

❏ 4098.700 Tank and tank cover only with tank

cover locking device

❏ 4098.800 Tank and tank cover only with right

hand trip lever

❏ 4098.900 Tank complete with right hand trip

lever and tank cover locking device

Compliance Certications -

Meets or Exceeds the Following Specications:

• ASME A112.19.2 for Vitreous China Fixtures

NOTES:

THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION

OF 305mm (12") FROM FINISHED WALL TO C/L OF OUTLET.

SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED

SEPARATELY.

DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.

IMPORTANT: Dimensions of xtures are nominal and may vary within

the range of tolerances established by ANSI Standard A112.19.2. These

measurements are subject to change or cancellation. No responsibility is

assumed for use of superseded or voided pages.

(305mm)

31-3/4

(806mm)

C/L OF OUTLET

3-1/4

(83mm)

FINISHED WALL

8-7/8

(225mm)

3/4 ± 1/4

(19mm ± 6mm)

16-1/2

(419mm)

18-1/2

(470mm)

C/L OF SEAT POST HOLES

5-1/2 (140mm CENTERS)

13-3/8

(340mm)

5-3/4

(146mm)

5/8

(16mm)

FINISHED

FLOOR

31-1/2

(800mm)

(254mm)

(152mm)

19-1/2

(495mm)

(254mm)

SUPPLY

REQ'D

(381mm)

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES

AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE

BUILDING FACILITIES - CHECK LOCAL CODES.

When installed so top of seat is 432 to 483mm (17" to 19") from the

finished floor.

BARRIER FREE

American Standard CADET RIGHT HEIGHT 2377.100 User manual

American Standard CADET RIGHT HEIGHT 2377.100 User manual

American Standard CADET RIGHT HEIGHT 2377.100 User manual

Related papers

Other documents