Peavey CAB 8i User manual

Type
User manual
Description
The CAB
ª
8i and CAB
ª
8o,
respectively, are eight-input and eight-
output MediaMatrix
¨
gateways onto and
off of an Ethernet network for real-time
MediaMatrix
¨
audio distribution and
control. They employ Cobranet proprietary
protocol to ensure seamless, error-free
transmission of high-quality real-time
audio without drop-outs or lossy
compression across a 100baseT Ethernet
network.
The CAB
ª
8i uploads eight channels of
either microphone-level or line-level
analog audio signals onto an Ethernet
network. Each input channel has software
controlled, continuously variable analog
input gain from -9 dB to +60 dB in 1 dB
steps. Each has 48-volt phantom power
and a 20 dB mic/line pad. Both functions
are software switchable.
The CAB 8o downloads eight channels
of line-level analog audio signals from an
Ethernet network. Maximum output levels
are individually jumper-selectable between
+24 dBu, +18 dBu, +12 dBu, and +6 dBu.
In addition to eight input or output audio
paths, both products incorporate eight
voltage-control input ports, eight software
controlled TTL outputs port, eight software
controlled relays with both normally open
and normally closed contacts, an RS-485
port with multi-drop connections, and two
word-clock linking BNC connectors.
Features
¥ Eight channels of either microphone
or line-level audio transmitted onto
an Ethernet network using CobraNet
ª
protocol sampled at 48 kHz (CAB 8i).
¥ Eight channels of line-level audio
transmitted from an Ethernet network
using CobraNet protocol sampled at
48 kHz (CAB 8o).
¥ A/D converters are 24-bit, 64 times
oversampling, using delta-sigma
modulation (CAB 8i).
¥ D/A converters are 24-bit, 128 times
oversampling, using delta-sigma
modulation (CAB 8o).
¥ 48-volt phantom power for microphone
inputs, individually software switchable
on each input channel (CAB 8i).
¥ 24- or 20-bit transmission quantization
at a 48 kHz sampling rate.
¥ Eight channels of analog control voltage
input ports which allow external
switches, potentiometers, or voltage
sources to control MediaMatrix software
parameters via an Ethernet link.
¥ Eight channels of TTL control outputs
ports which are software controllable via
an Ethernet link.
¥ Eight relays, with both normally open
and normally closed contacts, which
allow software control of external
devices via an Ethernet link.
¥ A non-Ethernet RS-485 control port with
two mulit-drop connections.
¥ Two word clock linking connectors that
enable auto-switch-over to a second
unit, should one unit fail.
¥ One rack-unit (1-3/4"), fan-cooled
chassis.
Applications
¥ Stadiums
¥ Cruise ships
¥ Multi-purpose facilities
¥ Auditoriums
¥ Large-scale paging systems
¥ Schools
¥ Courts of law
¥ University campus buildings
¥ Theme parks
¥ Performing arts centers
¥ Distance learning
¥ Hotel meeting rooms
¥ Houses of worship
¥ Conference centers
¥ Teleconferencing
¥ Live sound microphone snakes
¥ Civic centers
¥ Music clubs
¥ Theaters
¥ Arenas
¥ Any facility requiring distribution of
multiple microphone or line-level
signals
SPECIFICATIONS
MediaMatrix
®
CAB
8i and
CAB
8o
AUDIO SPECIFICATIONS
Audio Channels:
CAB 8i: Eight input channels, line-level
or microphone level with switchable
48-volt phantom power.
CAB 8o: Eight output channels, line-
level with individual channel jumpers for
a maximum output of +6, +12, +18, or
+24 dBu (factory default is +12 dBu for
unity I/O gain).
Note: See Digital specifications, Audio
Channels per CAB 8i/8o for number of
channels limitations.
Frequency Response:
20 Hz Ð 20 kHz, +0/-0.5 dB, with a
+4 dBu input signal, unity gain in and out.*
Total Harmonic Distortion:
0.01% @ 1 kHz, 0.02% @ 20 kHz, with
a +4 dBu input signal, unity gain in and
out*
Note: Measurements made using a 10
Hz to 30 kHz input filter on Audio
Precision System One for testing.
Dynamic Range:
Mic Level:
Ð123 dBu equivalent input noise with a
150 Ohm, Ð48 dBu input signal, no input
pad, analog input gain at 60 dB, digital
gain at 0 dB, analog output set for
+12 dBu maximum (factory pre-set
jumper for unity gain through-put)
Note: This is equivalent to 78 dBA,
75 dB unweighted.
Line level:
95 dBA, 93 dB unweighted, with a
+12 dBu input signal, unity gain in and out*
Input CMRR (CAB 8i):
Better Than 65 dB at Any Gain
Setting:
73 dB with +12 dBu input and unity gain
in and out*, 69 dB with a +4 dBu input
signal and unity gain in and out*, 68 dB
with a Ð56 dBu input signal, no input
pad, analog input gain at 60 dB, digital
gain at 0 dB, analog output set for
+12 dBu maximum (factory pre-set
jumper for unity gain through-put).
Maximum Input Level (CAB 8i):
+29 dBu, with a 20 dB pad in and the
analog input gain at 0 dB, +38 dBu with
a 20 dB pad in and the analog input gain
at Ð9 dB.
Note: The analog input gain control is
not buffered with an electronically
balanced amplifier and maintains a
balanced input circuit with
1-dB-per-step precision and specified
CMRR.
Maximum Output Level (CAB 8o):
+24 dBu @ 600 ohms
CAB 8i Gain:
Software controlled analog gain from
Ð9d B to +60 dB, adjustable in 1 dB
increments, with a software selectable
analog Mic/Line input switch. (Line level
selection inserts a 20 dB input pad.)
CAB 8o Gain:
Software controlled analog output gain
from Ð95.5 dB to +31.5 dB, adjustable
in 0.5 dB increments with internal analog
output jumpers for maximum output
levels of +6, +12, +18, or +24 dBu
Note: It is not recommended to use this
as a microphone level output as noise
will be a problem at extremely low
output levels.
Input Impedance (CAB 8i):
22.2 k ohms for Line input selection and
2.2 k ohms for Mic input selection
Output Impedance (CAB 8o):
100 Ohms, designed to drive a minimum
load of 600 Ohms
Analog LED Metering:
Eight peak-reading headroom meters,
calibrated in dBu, monitor the analog
level present at the input to the A/D
converters for the CAB 8i, and at the
output of the D/A converters for the CAB
8o, with the top-most red LED indicating
A/D or D/A clipping.
Note: The top-most red LED should
never illuminate during normal operation.
Note 1: Audio specifications are measured
from the input into the CAB 8i and the
output out of the CAB 8o where relevant.
Note 2: All specifications are typical.
*Indicates no input pad, analog input gain
at 0 dB, digital gain at 0 dB, analog output
set for +12 dBu maximum (factory pre-set
jumper for unity gain through-put).
DIGITAL SPECIFICATIONS
A/D and D/A quantization:
24-bit resolution
Audio Transmission Quantization
via CobraNet
ª
:
Software switchable, 24 or 20-bit resolution
Digital Processing:
24-bit DSPÕs, 56-bit accumulators
Audio Sampling Rate and Clock
Speeds:
48 kHz audio sampling, 80 MHz DSPÕs,
12.288 MHz master clock
Audio Channels Per CAB 8i/8o:
¥ Eight with 20-bit transmission quanti-
zation selected
¥ Seven with 24-bit transmission quanti-
zation selected
CONTROL SPECIFICATIONS
CobraNet
ª
I/O:
100BaseT Ethernet via a standard
eight-conductor RJ-45 jack
RS-485:
One port with two 3-cond. half duplex,
multi-drop connections
Control Ports:
Control voltage in:
0 VDC to +10 VDC, external-
potentiometer or external-voltage-source
controlled (internal 10 VDC supply
provided)
Software controlled TTL (Transistor-
to-Transistor Logic) out:
0 VDC or +5 VDC, with a maximum
current of 28 mA distributed to 8 outputs
Eight Software Controlled Relays
With Both NO and NC Contact:
Maximum contact voltage:
120 VAC or DC
Maximum contact current:
2 A
Word-Clock Ports:
Two BNC I/O ports
Note: Can be used for redundancy
back-up that automaticaly switches from
one CAB 8 to another if the first should
fail.
GENERAL SPECIFICATIONS
Dimensions:
CAB 8i CAB 8o:
1.730" H x 19" W x 11.698" D
(4.39 cm H x 48.26 cm W x 29.71 cm D)
Net Weight:
CAB 8i: 8.5 lbs. (3.86 kg)
CAB 8o: 8.4 lbs. (3.81 kg)
AC Power:
Universal Power Supply:
1.4 A maximum, 100 to 240 VAC, 47
to 63 Hz
Power Consumption and Heat
Generation:
CAB 8i: 25 W, 85 BTU/Hr
CAB 8o: 20 W, 68 BTU/Hr
Maximum In-Rush Current:
CAB 8i and CAB 8o: less than 1.4 Amps
Finish:
Grey powder-coat painted steel
Accessories:
One detachable AC cord, four rubber
adhesive feet
Product Agency Compliance
Listings:
UL, CUL, CE and FCC part 15, A
2
Frequency Response
T.H.D. versus Frequency
3
Functional Block Diagram
16.840"
427.736mm
1.080"
27.438mm
11.698"
297.129mm
1.730"
43.942mm
1.730"
43.942mm
19.0"
482.6mm
Mechanical Diagram
4
ARCHITECTSÕ AND ENGINEERSÕ
SPECIFICATIONS
Audio specifications are measured with
the input fed into the CAB 8i, digitally
transmitted through an Ethernet hub, and
the output fed out of the CAB 8o where
relevant.
CAB 8i:
The Peavey CAB 8i shall provide eight
channels of either microphone or line-level
audio transmitted onto an Ethernet
network. It shall provide full-bandwidth,
high-quality audio transmission via
100BaseT (fast) Ethernet without lossy
compression techniques, drop-outs or
signal degradation by employing CobraNet
audio transmission protocol to make
Ethernet signal distribution deterministic.
It shall employ 24-bit A/D converters with
20- or 24-bit selectable transmission
quantization utilizing a 48 kHz sampling rate.
It shall have a frequency response from
20 Hz to 20 kHz, +0/-0.5 dB or better. Its
total harmonic distortion shall be no more
than 0.01% at 1 kHz and 0.02% at 20 kHz
with a +4 dBu input signal. It shall have a
dynamic range of 95 dBA and 93 dB
unweighted for line-level signals, and an
equivalent input noise level of Ð124 dB for
microphone level signals. Input-common-
mode-rejection ratio (CMRR) shall be
greater than 65 dB at any gain setting.
Maximum input level without clipping shall
be +38 dBu while maintaining specified
CMRR. CAB 8i input gain shall be from
Ð9 dB to +60 dB in 1-dB steps. The CAB
8i input impedance shall be 2.2 k ohms at
microphone level (20 dB pad out), and
22.2 k ohms at line level (20 dB pad in).
Control features shall include eight relays
with both normally open and normally
closed contacts, and eight channels of
TTL control outputs, both of which are
software controllable via an Ethernet link.
Also included are eight channels of analog
voltage-control ports that allow external
switches, potentiometers or voltage
sources to control MediaMatrix software
parameters via an Ethernet link.
Front-panel indicators shall display the
following status conditions: signal
transmission, signal reception,
transmission error, reception error, fault
indication, link indication, conductor
status, RS-485 control indication, and
power presence. It shall have eight peak-
reading headroom meters to monitor the
analog level present at the input to the
A/D converters, with the top-most red LED
indicating A/D clipping.
Rear panel features shall include a
detactable AC power cord, an AC power
switch, and an AC power receptacle with a
built-in auto-resetting circuit breaker.
External or internal fuses shall not be
acceptable. It shall have two word-clock
connectors to enable auto-switch-over
should a unit fail. It shall employ
detachable, euro-style, bare-wire
capturing, screw-terminal connectors for
ease of hook-up and trouble-shooting.
These connectors shall be used for all
line-level, microphone-level, control-
voltage, TTL, relay, and RS-485
connections. The unit shall use a
standard eight-conductor RJ-45 I/O
jack for Ethernet connection.
Its dimensions shall be 19 inches (48.26 cm)
wide, 12 7/8 inches (32.70 cm), and 1 3/4
inches (4.44 cm) high without feet. Its net
weight shall be 8.5 pounds (3.86 kg.), and
its 1 rack-unit (1 3/4"), fan-cooled, steel
chassis, shall be finished in grey powder
coat.
It shall consume no more than 25 Watts of
power and draw no more than 1.4 Amps
of current. It shall be supplied with a
detachable AC cable and four rubber feet.
It shall be UL, CUL, CE listed and comply
with FCC part 15, A. The unit shall be
Peavey Electronics Corporation model
CAB 8i.
CAB 8o:
The Peavey CAB 8o shall provide eight
channels of line-level audio transmitted
from an Ethernet network. It shall provide
full-bandwidth, high-quality audio
transmission via 100BaseT (fast) Ethernet
without lossy compression techniques,
drop-outs or signal degradation by
employing CobraNet audio transmission
protocol to make Ethernet deterministic. It
shall employ 24-bit A/D converters with
20- or 24-bit selectable transmission
quantization utilizing a 48 kHz sampling rate.
It shall have a frequency response from
20 Hz to 20 kHz, +0/-0.5 dB or better. Its
total harmonic distortion shall be no more
than 0.01% at 1 kHz and 0.02% at 20 kHz
with a +4 dBu output signal. It shall have a
dynamic range of 95 dBA and 93 dB
unweighted. Maximum output level shall
be +24 dBu with a load of 600 ohms or
greater. CAB 8o gain shall be from
Ð95.5 dB to +31.5 dB in 0.5 dB steps. The
output impedance of the CAB 8o shall be
100 ohms and designed to drive a load of
600 ohms or greater.
Control features shall include eight relays
with both normally open and normally
closed contacts, and eight channels of
TTL control outputs, both of which are
software controllable via an Ethernet link.
Also included are eight channels of analog
voltage-control ports that allow external
switches potentiometers or voltage
sources to control MediaMatrix software
parameters via an Ethernet link.
Front-panel indicators shall display the
following status conditions: signal
transmission, signal reception,
transmission error, reception error, fault
indication, link indication, conductor
status, RS-485 control indication, and
power presence. It shall have eight peak-
reading headroom meters to monitor the
analog level present at the output of the
D/A converters, with the top-most red LED
indicating D/A clipping.
Rear panel features shall include a
detachable AC power cord, an AC power
switch, and an AC power receptacle with a
built-in auto-resetting circuit breaker.
External or internal fuses shall not be
acceptable. It shall have two word-clock
connectors to enable auto-switch-over
should a unit fail. It shall employ
detachable, euro-style, bare-wire
capturing, screw-terminal connectors for
ease of hook-up and trouble-shooting.
These connectors shall be used for all
line-level, control-voltage, TTL, relay, and
RS-485 connections. The unit shall use a
standard eight-conductor RJ-45 I/O jack
for Ethernet connection.
Its dimensions shall be 19 inches (48.26 cm)
wide, 12 7/8 inches (32.70 cm), and 1 3/4
inches (4.44 cm) high without feet. Its net
weight shall be 8.4 pounds (3.81 kg.), and
its 1 rack-unit (1 3/4"), fan-cooled, steel
chassis, shall be finished in grey powder
coat.
It shall consume no more than 20 Watts of
power and draw no more than 1.4 Amps
of current. It shall be supplied with a
detachable AC cable and four rubber feet.
It shall be UL, CUL, CE listed and comply
with FCC part 15, A. The unit shall be
Peavey Electronics Corp. model CAB 8o.
5
3 + 2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the warranty statement. Copies of
this statement may be obtained by contacting
Peavey Electronics Corporation
P.O. Box 2898, Meridian, Mississippi 39301-2898.
Features and specifications subject to change without notice.
Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301
(601) 483-5376 • FAX (601) 486-1678 • aa.peavey.com
©1999 Printed in the U.S.A. 5/99
80304547
ARCHITECTURAL ACOUSTICS
¨
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Peavey CAB 8i User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI