Thank you for selecting Aiphone for your communication and security needs. Please read this manual carefully before installation,
and keep it in a safe place for future reference.
Please note that the illustrations in this manual may differ from the actual product.
JM-DVF-L
VIDEO DOOR STATION (GUIDANCE-ENABLED TYPE)
INSTALLATION MANUAL
FK1876 A P1112OZ
2
PRECAUTIONS
Prohibited Do not dismantle unit Keep unit away from water General precautions
WARNING
Negligence could result in death or serious injury.
1. Do not dismantle or alter the unit. Fire or electric shock could
result.
2. The unit must be installed and wired by a qualifi ed technician.
CAUTION
Negligence could result in injury to people or damage to property.
1.
Do not install or make any wire terminations while power supply
is plugged in. It can cause electrical shock or damage to the unit.
2. When mounting the unit on a wall, install the unit in a
convenient location, but not where it could be jarred or
bumped. Injury could result.
3. Before turning on power, make sure wires are not crossed or
shorted. Fire or electric shock could result.
4. Do not install the unit in any of the following locations. Fire,
electric shock, or unit trouble could result.
Places under direct sunlight or near heating equipment that *
varies in temperature.
Places subject to dust, oil, chemicals, hydrogen sulfi de (hot *
spring).
Places subject to moisture and humidity extremes, such as *
bathrooms, cellars, greenhouses, etc.
Places where the temperature is low, such as inside a *
refrigerated area or in front of an air conditioner.
Places subject to steam or smoke (near heating or cooking *
surfaces).
Where noise generating devices such as dimmer switches or *
inverter electrical appliances are closeby.
GENERAL PRECAUTIONS
1. Keep the unit more than 1 m (3.3') away from radio or TV sets.
2. Keep the intercom wires more than 30cm (12'') away from AC
100-240V wiring. AC induced noise and/or unit malfunction could
result.
3. The unit will not work during power failure.
4. Door station is weather-resistant, but do not spray with high-
pressure water. Unit trouble could result.
5. When outside temperature lowers sharply after rainfall, etc., the
inside of the camera may fog up slightly, causing a blurry image,
but this is not a malfunction. Normal operation will be restored
when moisture evaporates.
6. Environmental sound around the unit may hinder smooth
communication, but this is not a malfunction.
NOTICES
We will under no conditions be liable for damage occurring due
•
to the inability to communicate due to malfunctions, problems, or
operational errors in this product.
This manual was created by Aiphone Co., Ltd., all rights reserved.
•
Copying, in part or in whole, this manual without prior permission
from Aiphone Co,. Ltd. is strictly forbidden.
Please note that images and illustrations depicted in this manual
•
may differ from the actual ones.
Please note that this manual may be revised or changed without
•
prior notice.
Please note that product specifi cations may be changed for the sake
•
of improvement without prior notice.
CONTENTS
PRECAUTIONS ................................ 2
WARNING ........................................... 2
CAUTION ............................................ 2
GENERAL PRECAUTIONS ............... 2
NOTICES ............................................ 2
PACKAGE CONTENTS ................... 3
PART NAMES ................................. 3
CONNECTIONS ............................... 4
MOUNTING ..................................... 5
Mounting locations ........................... 5
Mounting positions and image
view area ............................................ 5
Mounting ............................................ 6
TECHNICAL DATA AND
PRECAUTIONS ................................
6
WARRANTY .....................................
7
3
PACKAGE CONTENTS
Verify that the following parts are included.
The unit Flash mount back box Special screw x 4 Speial screwdriver
Transparent name plate x 2 Installation Manual
PART NAMES
Voice guidance
This station also sounds messages in the following states.
State Message
When a calling is started "Call in progress"
When talking becomes enabled "Please speak now"
When the door lock is released "Door open"
The language for the messages depends on the language setting made on
*
the master station.
Name plate (with backlight)
Write down a name on the plate. The backlight is
always lit while the power is on to enable a visitor
to confi rm the name even at night.
Call button
Calls the preset master and sub master stations.
Door release indicator (green)
Lights up while the door lock is released from the
master station or a sub master station.
Talk indicator (orange)
Lights up while talking.
Call indicator (orange)
Lights up while calling.
Camera
Captures images to display on the screens of the
master and sub master stations.
Microphone
Sends sounds from the door station to the master and
sub master stations.
White light LED
Lights up automatically when it gets dark around
this station.
Blinks when this station is sounding an alarm.
These functions can be enabled or disabled by the
setting on the master station.
Speaker
Outputs sounds from the master station or a sub
master station.
4
CONNECTIONS
■
Notes on cables
Use PE (polyethylene)-insulated PVC jacket cable.
•
Parallel or jacketed 2-conductor, mid-capacitance, non-shielded cable
is recommended.
Never use individual conductors, twisted pair cable, or coaxial cable.
•
■
Wiring distance
Wire diameter
Ø0.65 mm
(22 AWG)
Ø0.8 mm
(20 AWG)
Ø1.0 mm
(18 AWG)
Ø1.2 mm
(16 AWG)
[A]
50 m (165') 100 m (330') 100 m (330') 100 m (330')
[B]
10 m (33')
■
Connection diagram
NC
A1
A2
COM
NO
PT
1A1
1A2
NP
2
[A]
[B]
[B]
[B]
Master station
JM-4MED
Video door station
(guidance-enabled type)
JM-DVF-L
AC transformer
The terminals are inside the terminal
•
cover. After connecting, route the
wires through the wiring paths, then
close the cover.
Be sure to route the wires through
•
inlet.
When closing the terminal cover,
•
close it until it clicks.
*
2
: Not available.
Do not connect a LAN connector,
etc. to this port.
Electric door strike
*1
EL-12S etc.
Terminal cover
Inlet
Wires
Connect to the electric door strike
according to its specifi cations.
NOTES:
Do not use the unused terminals for other purposes.
•
In order to prevent miswiring, label both ends of each cable
•
with the unit and terminal names to which they are to be
connected.
For connecting other manufacturers’ products, refer to the
•
instruction manuals for those products.
The illustration of the unit’s rear panel differs from the actual
•
product. This is to simplify the diagram.
*1: Output specifi cations
Output method N/O or N/C dry closure contact
Voltage between
terminals
24V AC, 0.5A (resistive load)
24V DC, 0.5A (resistive load)
Minimum overload (AC/DC):
100mV, 0.1mA
*
2
5
MOUNTING
Mounting locations
Do not install this station in any of the following locations where lighting or the ambient environment could impact the display on the
screen of the master station or a sub master station due to the characteristics of this station's camera.
a
Locations subject to
direct sunlight
b
There is a white wall behind
the caller
c
Other locations subject to strong
lighting or backlighting conditions
Mounting positions and image view area
Wide image
An area over a range of approx. 170° in a 500 mm
(20") radius from the camera displays.
(The display range is a rough estimation and may
change due to the installation environment.)
Mounting position
1,500 mm (5')
Mounting position
1,300 mm (4' 3")
Unit center
Approx. 1,050 mm (3' 5")
Approx. 2,100 mm (6' 11")
Approx. 1,050 mm (3' 5")
1,500 mm (5')
500 mm (20")
500 mm (20")
Approx. 170°
Approx. 1,050 mm (3' 5")
Approx. 1,900 mm (6' 3")
Approx. 850 mm (2' 9")
Unit center
1,300 mm (4' 3")
500 mm (20")
Up/Down
Left/Right
Zoom <Up>
Unit center
Approx. 2,350 mm (7' 8")
Approx. 850 mm (2' 9")
Approx. 1,500 mm (5')
500 mm
(20")
1,500 mm (5')
Zoom <Down>
Approx. 750 mm (2' 5")
Approx. 1,600 mm (5' 4")
Approx. 850 mm (2' 9")
500 mm (20")
Unit center
1,500 mm (5')
Zoom <Right>
500 mm (20")
Approx. 100 mm (4")
Approx. 1,300 mm (4' 3")
Zoom <Center>
500 mm (20")
Approx. 900 mm (3')
Zoom <Left>
500 mm (20")
Approx. 1,300 mm (4' 3")
Approx. 100 mm
(4")
Wide image
Zoom image
The zoom position can be changed. (Refer to the
master station's "OPERATION MANUAL".)
The factory setting is "Center" for Zoom mode.
Approx.
1,050 mm
(3' 5")
Approx. 700 mm (2' 3")
Approx. 900 mm (3')
Objects appear
smaller due to
greater distortion
in the surrounding
sections compared to
the central section,
but a wider area is
displayed.
The display range is
a rough estimation
and may change due
to the installation
environment.
Zoom image (when mounting position is 1,500 mm (5'))
Zoom <Center>
1,500 mm (5')
Approx. 1,900 mm (6' 3")
Approx. 700 mm (2' 3")
Approx. 1,200 mm (3' 11")
Unit center
500 mm (20")
6
Mounting
Tighten
Special screw x 4 (included)
Vandal-resistant front panel
with the unit attached
Flush mount back box (included)
Transparent name plate
45 mm
(1-3/4'')
120 mm
(4-3/4'')
279 mm
(11'')
Mounting height (box center)
GL=1,500 mm (5')
Loosen
Special screwdriver
(included)
Install the back box in the wall, and
1
then connect the wires to the unit
with the terminal cover open.
Insert the transparent name plate.
2
1
Peel off the protective seals on the plate (both sides).
2
Fill in the name on the transparent name plate.
Be sure to leave 25 mm (1") of white space on the
right end to account for insertion.
3
Insert the fi lled-in transparent name plate at the
specifi ed insertion opening (indicated with in
diagram).
ABCDEFG
Fasten the front panel
3
to the back box with the
special screws.
To insertion
opening
2 mm (1/8")
25 mm
(1")
TECHNICAL DATA AND PRECAUTIONS
Technical data
Power supply Supplied from master station
Operating temperature - 10 - 60°C (+14°F - +140°F)
Dimensions JM-DVF-L 150 (W) x 309 (H) x 30 (D) mm
5-15/16" (W) x 12-3/16" (H) x 1-3/16" (D)
Flush mount back box 120 (W) x 279 (H) x 45 (D) mm
4-3/4" (W) x 11" (H) x 1-3/4" (D)
Weight JM-DVF-L Approx. 980g (2.16 lbs.)
Flush mount back box Approx. 670g (1.48 lbs.)
Technical precautions
Cleaning: Clean units with a soft cloth and gentle cleaner. Do not spray cleaner directly on unit. Do not use an abrasive cleanser or
•
cloth.
7
WARRANTY
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for
a period of two years after delivery to the ultimate user and will repair free of charge or replace at no charge, should it
become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto
itself the sole right to make the fi nal decision whether there is a defect in materials and/or workmanship; and whether or
not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to
misuse, neglect, accident, power surge, or to use in violation of instructions furnished, nor extended to units which have
been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries
used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop
or place designated in writing by Aiphone. This warranty is limited to the standard specifi cations listed in the operation
manual. This warranty does not cover any supplementary function of a third party product that is added by users or
suppliers. Please note that any damage or other issues caused by failure of function or interconnection with Aiphone
products is also not covered by this warranty. Aiphone will not be responsible for any costs incurred involving on site
service calls. Aiphone will not provide compensation for any loss or damage incurred by the breakdown or malfunction of
its products during use, or for any consequent inconvenience or losses that may result.
The object area of is the EU.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Increase the separation
•
between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
•
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE S.A.S., LISSES-EVRY, FRANCE
http://www.aiphone.net/
Printed in Thailand
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Aiphone 834168 C P0811JZ User manual
-
Aiphone JK-DA User manual
-
Aiphone JP-DA Installation guide
-
Aiphone FK1628 B P0811JZ User manual
-
-
Aiphone JO-1MDW Install Manual
-
-
Aiphone IXG Install Manual
-
Aiphone GT Install Manual
-
Aiphone TX-1200 Installation guide
