ABH 6600-C-AB Series Installation guide

Brand
ABH
Model
6600-C-AB Series
Type
Installation guide

ABH 6600-C-AB Series is an asylum trim round knob designed for mortise lock installation. It features a pre-assembled asylum trim assembly for easy installation. The device is suitable for doors with a vision lite that is at least 6" from the centerline of the trim. It comes with an adapter plate for proper alignment and adjustment. The asylum cover screws together with 8-32 screws for a secure fit. The device is designed to be mounted vertically with levers down.

ABH 6600-C-AB Series is an asylum trim round knob designed for mortise lock installation. It features a pre-assembled asylum trim assembly for easy installation. The device is suitable for doors with a vision lite that is at least 6" from the centerline of the trim. It comes with an adapter plate for proper alignment and adjustment. The asylum cover screws together with 8-32 screws for a secure fit. The device is designed to be mounted vertically with levers down.

6600-C-AB SERIES, ASYLUM TRIM ROUND KNOB
INSTALLATION FOR MORTISE LOCK
c 2017 ABH Mfg., Inc.
printed in USA
"C" ASYLUM HANDLES
MUST BE MOUNTED
IN THIS POSITION
DOWN
LEVERS
ASYLUM TRIM ASSEMBLY
IS PRE ASSEMBLED
AT THE FACTORY
NOTES
1. TRIM MUST BE MOUNTED VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
3. USES AB6600 SERIES MORTISE LOCK DOOR PREP.
4. MORTISE LOCK CYLINDER & LOCK CAM NOT PROVIDED.
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR,
DETERMINE IF THE DOOR WILL
RECEIVE AN EDGE GUARD. IF SO,
THE EDGE GUARD SHOULD BE
INSTALLED FIRST AND THEN THE
PREP FOR THE MORTISE LOCK
SHOULD BE MEASURED FROM THE
OUTSIDE EDGE OF THE EDGE
GUARD.
4
3
2C
INSTALLATION INSTRUCTIONS:
1. Prep for lockbody according to mortise lock manufacturer installation. Install mortise lock (item 6) using (2) 12-24 screws (item 8). Then
mount the face plate (item 7) using (2) 8-32 screws (item 9).
2. A) Place the pre-assembled asylum trim assembly 1A on the side of the door that will match the diagonal mortise lock mounting through
holes.
B) Place the adapter plate 2B centered with pre-assembled asylum trim assembly 1A while inserting the (2) 10-32 screws (item 5).
C) After tightening the mounting screws (item 5) test lock and asylum trim assembly 1A for proper latch retraction and knob operation. If
the latch does not extend / retract or if trim knob is binding, Loosen 10-32 head screws (item 5) and adjust alignment for proper
operation and re-tighten.
D) Place the asylum trim assembly 2A on the door so that spindle engages with the mortise lock and fasten with (4) 8-32 screws (item 4).
Test the knob for latch retraction. If latch does not extend loosen both 10-32 screws (item 5) to readjust alignment and re-tighten.
E) Place the asylum cover (item 2C) on the asylum trim assembly and screw together with (4) 8-32 screws (item 3).
O
R
Lockset function
Caution: Not all holes shown below need
to be drilled. Use the diagram AND the
chart to determine the holes that you need
to drill for your trim and function
combination.
Cylinder
1-1/4" dia.
5/8" dia.
Turn knob
1-1/8" dia.
Trim
1/2" dia.(2)
Thru-bolt
Emergency Key
1 2 4 5 1 2 4 5
Cylinder
Trim
1-1/8" dia.
Thru-bolt
1/2" dia.(2)
Outside holes
Inside holes
ADA recommends mounting centerline of lock 44" from top of finished floor.
6641
Determine trim holes based on trim type.
*
6
(2)
Trim turn knob
*
6
*
(2)
Trim turn knob
1-1/4" dia.
1/2" dia.
-OR- Check local ordinance for proper height.
(Asylum Lock)
1
5
5
4
1-1/4 dia.
1/2 dia.
1-1/8 dia.
1/2 dia.
SEE CHART
2
6
*
6600-C-AB SERIES, HOLE PATTERN
CHART
ISSUED 02-03-17
6600-C-AB-2-00.DWG
6600-C-AB
PAGE 2 OF 3
O
R
of lock 44" from top of finished floor.
ADA recommends mounting centerline
FINISHED FLOOR
5
3
4
CENTERLINE
OF LEVER
CENTERLINE
OF LOCK
TOP VIEW
SHOWN WITH DEAD BOLT
FRONT VIEW
SHOWN WITH OUT
DEAD BOLT
FRONT VIEW
SHOWN WITH
DEAD BOLT
ASA STRIKE
STRIKE BOX
SIDE VIEW
SHOWN WITH DEAD BOLT
5
2
2
27
64
TAP FOR #12-24
MACHINE SCREW
OR #12 WOOD
SCREW (2 PLACES)
1
5
7
8
3
5
8
13
16
ADJUSTABLE BETWEEN

1
8
4
1
4
1
2
3
4
BACKSET
1
1
7
8
CLEARANCE FOR
SCREWS-1/16"
7
32
DEEP
1
11
16

1
1
2
7
32
1
1
4
8
7
1
4
4
11
16
3
8
3
3
8
CENTERLINE
OF STRIKE
4
1
8
3
7
16
(STRIKE
BOX)
4
7
8
1
1
4
3
64
1
7
32
31
32
1
1
32
19
32
1
3
16
19
32
1
3
16
-OR-
Check local ordinance for proper height.
Lock case holes:
1 Cylinder hole-1-1/4" dia.
2 Turn knob-5/8" dia. / Emergency
key-1/2" dia.
4 Trim hole-1-1/8" dia.
5 Thru-bolt holes-
(two required) 1/2" dia.
4, For metal door, lock case support
is required from the door manufacturer.
5, Tap for a #12-24 machine screw
or drill for a #12 wood screw (a
combination screw is supplied).
Notes:
1, Before drilling check the hole
pattern chart.
2, The maximum door-to-frame
gap is 3/16".
3, Allow 3/64" clearance for the
strike box thickness.
5
64
6600-C-AB SERIES, DOOR & FRAME PREP
ISSUED 02-03-17
6600-C-AB-3-00.DWG
6600-C-AB
PAGE 3 OF 3
  • Page 1 1
  • Page 2 2
  • Page 3 3

ABH 6600-C-AB Series Installation guide

Brand
ABH
Model
6600-C-AB Series
Type
Installation guide

ABH 6600-C-AB Series is an asylum trim round knob designed for mortise lock installation. It features a pre-assembled asylum trim assembly for easy installation. The device is suitable for doors with a vision lite that is at least 6" from the centerline of the trim. It comes with an adapter plate for proper alignment and adjustment. The asylum cover screws together with 8-32 screws for a secure fit. The device is designed to be mounted vertically with levers down.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents