Ignis LOE 6056 Program Chart

Type
Program Chart

This manual is also suitable for

GB PROGRAMME CHART
5019 501 05022
: optional / Yes : dosing required
1)
For improved garment care, spin speed is restricted to 400 rpm in this programme.
Programme
Care
Labels
Type of wash/Notes
- For temperature selection, respect the manufacturer’s
recommendations on the care label
Max
Load
kg
Detergents and additives Special options
Max
Spin
Speed
rpm
Pre-
wash
Main
Wash
Softener Start
delay
Eco Pre-
wash
Intensive
rinse
Rinse
hold
Variable
spin
Avvio
ritardato
Pre-
lavaggio
Risciacquo
intensivo
Anti
piega
Centrifuga
variabile
Cotton
40 - 60 - 95 °C
Cotone
40 - 60 - 95 °C
Normally to heavily soiled bed linen, table linen and
underwear, towels, shirts etc. made of cotton and linen.
With heavily soiled laundry the additional “Prewash”
option can be selected as well.
5.0
Yes
❉❉
max.
Synthetics
30 - 40 - 60 °C
Sintetici
30 - 40 - 60 °C
Normally soiled blouses, shirts, overalls etc. made of
polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or
blends with cotton.
2.5
Yes
❉❉
max.
Delicates
30 - 40 °C
Delicati
30 - 40 °C
Curtains and delicate clothing, dresses skirts, shirts and
blouses.
1.5
Yes
❉❉
❉❉
max.
Daily load
40 °C
Slightly to normally soiled textiles made of cotton and/or
synthetics.
3.0 Yes
❉❉
——
❉❉
max.
Quick wash
30 °C
Rapido
Shortly worn outer clothing made of cotton, polyester,
polyamide and blends with cotton.
3.0 Yes
❉❉
——
❉❉
max.
Wool
Cold - 40 °C
Lana
Lana a freddo - 40 °C
Only woollens, labelled with the Woolmark and identified
as machine washable.
If you select “Rinse Hold” do not leave items to soak for too
long.
1.0 Yes
❉❉
——
❉❉
max.
Handwash
30 - 40 °C
Lavaggio a mano
30 - 40 °C
Textiles made of linen, silk, wool and viscose marked as
“handwashable”.
If you select “Rinse Hold” do not leave items to soak for too
long. A very gentle spin is used in this programme.
1.0 Yes
❉❉
——
❉❉
400
1)
Rinse & Spin
Risciacquo &
Centrifuga
Same as the last rinse and the final spin in the “Cotton
programme.
5.0
❉❉
——
❉❉
max.
Spin Centrifuga
In this programme spinning is intensive. Same as the spin
cycle in the “Cotton” programme.
5.0
——
max.
Gentle Spin Centrifuga breve
In this programme spinning is gentle. Same as the spin cycle
in the “Wool” programme.
1.0
——
max.
Drain Scarico acqua
Water is drained only without any spinning. Alternative
method of terminating programme after “Rinse Hold”.
——
A. “Door open” indication
This washing machine is equipped with
automatic safety functions which
detect and diagnose faults at an early
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
and Start delay indicators
I. “Reset” button
J. “Start delay” button
D
H
C
F
I
G
E
B
A
J
50105022GB.fm Page 1 Thursday, October 11, 2007 6:56 PM
Black process 45.0° 100.0 LPI
5019 501 05022
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
Close the door and turn the programme selector to
the desired programme and temperature. The
indication lamp next to the
“Start/Pause”
button
flashes.
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and
additional option(s) is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
“Eco” button
With a modified temperature profile and a
slightly prolonged washing duration, the
optimum combination of excellent washing
result and even lower energy consumption is
achieved.
“Prewash” button
Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
Do not use liquid detergent for the main wash
when activating the Prewash option.
“Intensive rinse” button
More water is added and rinse cycle is
prolonged.
This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
Note:
The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indication is on. The indication lamp
next to the
“Start/Pause”
button flashes.
If you select “Rinse Hold” do not leave items to
soak for too long.
Terminate the “Rinse hold” option:
•Press the
“Start/Pause
button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the
“Start/Pause
button.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
*
Cotton 95 5.0 49
**
1.90 2:00
Cotton 60 5.0 44 0.95 2:10
Cotton with “Eco”
***
60 5.0 49 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50
**
0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Variable spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
Do not use liquid detergent when activating the
Start delay.
Select programme, temperature and options.
Press the “Start Delay button to select the
delay time by 1, 3, 6, 9 or 12 hours.
•Press the
“Start/Pause”
button.
The indication next to the “Start Delay” button
lights up and goes off when the programme
starts.
Once having pressed the
“Start/Pause”
button,
the countdown of the time delay begins. When
the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
After the
“Start/Pause”
button has been
pressed, the number of hours preselected can
be reduced by pressing again the “Start Delay
button.
To cancel the “Start Delay
..before you press the “Start/Pause” button:
Turn the programme selector to another
position or press the
“Reset”
button.
..after having pressed the “Start/Pause”
button:
Press the “Reset” button for at least 3 seconds -
the start delay indicator light goes out.
Open the tap and press the
“Start/Pause”
button.
The indication lamp next to the
“Start/Pause”
button lights up. The programme sequence
indicator shows the current programme phase,
running from left to right through Wash, Rinse, Spin/
Drain.
When the programme phase is finished, the
corresponding indication goes out.
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for
Use; if the fault persists, contact our After Sales
Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
All the lights of the programme sequence
indicator are off, and the “Door open
indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The
new programme continues at the same position
where the previous programme was
interrupted. Do not add detergent for this
programme.
The
“Reset”
button cancels a programme before
the end.
•Press the
“Reset”
button for at least
3 seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
50105022GB.fm Page 2 Thursday, October 11, 2007 6:56 PM
Black process 45.0° 100.0 LPI
  • Page 1 1
  • Page 2 2

Ignis LOE 6056 Program Chart

Type
Program Chart
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI