MODWAY EEI-3678-NAT-TAU Assembly Instructions

Type
Assembly Instructions
2. Seat
3. Leg Frame 1
x2
x1
Component:
Page 1 of 4
Thank you for purchasing the MODWAY CHAIR!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Customer Service 609-256-9000 www.modway.com
1. Back x1
1
2
4
6
4. Leg Frame 2 x1
EEI-3678/3679-NAT-TAU CHAIR
3
5
5. Brace Rail x1
6. Back Cushion x2
7. Seat Cushion x2
6
7
7
A
B
G
Bolt M6x110mm x 1
Bolt M6x90mm x 1
Allen Wrench M4 x 2
Screw M6x40mm x 8
F
Hardware:
A
B
G
Bolt M6x110mm x 1
Bolt M6x90mm x 1
Allen Wrench M4 x 2
Screw M6x60mm x 1
E
DNut M6 x 5
CBolt M6x70mm x 3
Screw M6x40mm x 8
F
Hardware:EEI-3678
The assembly steps are the same as EEI-3678
EEI-3679
Page 2 of 4
STEP 1:
Hardware & Tool required
STEP 2:
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
3
1
G
A
GG
BD
5
G
EEI-3678/3679-NAT-TAU CHAIR
G
D
C
D
G
x1
C
x2
G
x2
D
x1
A
x1
B
x1
D
x2
G
Attach Leg Frame 1 (3) to Back (1) as shown.
Insert 2 pieces of Nuts (D) into Back (1), then insert 1 piece of Bolt (A) and 1 piece of Bolt (C)
through Leg Frame 1 (3) into Back (1).
Tighten with 2 pieces of Allen Wrench (G).
Attach Brace Rail (5) to Leg Frame 1 (3) as shown.
Insert 1 piece of Nut (D) into Brace Rail (5), then insert 1 piece of Bolt (B) through Leg Frame 1 (3)
into Brace Rail (5).
Tighten with 2 pieces of Allen Wrench (G).
4
G
E
EEI-3678/3679-NAT-TAU CHAIR
G
D
C
G
Page 3 of 4
STEP 3:
Hardware & Tool required
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
GG
D
C
x1
C
x2
G
x1
D
x1
E
STEP 4:
Insert 1 piece of Nut (D) into Brace Rail (5), then insert 1 piece of Bolt (C) through Leg Frame 2 (4)
into Brace Rail (5).
Tighten with 2 pieces of Allen Wrench (G).
x1
C
x2
G
x1
D
Attach Leg Frame 2 (4) to Back (1), Brace Rail (5) and Leg Frame 1 (3) as shown.
Insert 1 piece of Nut (D) into Back (1), then insert 1 piece of Bolt (C) and 1 piece of Screw (E) through Leg
Frame 2 (4) into Back (1).
Tighten with 2 pieces of Allen Wrench (G).
Carefully position the assembled chair to the desired location.
Put 2 pieces of the Back Cushions (6) and 2 pieces of the Seat Cushions (7) into the assembled chair as shown.
Page 4 of 4
STEP 5:
Hardware & Tool required
STEP 6:
Assembly is complete. Your chair is ready to be used now!
Customer Service 609-256-9000 www.modway.com
G
F
7
EEI-3678/3679-NAT-TAU CHAIR
2
2
Attach 2 pieces of Seat (2) to the assembled Back (1), Brace Rail (5) and Leg Frame (3&4) as shown.
Then insert 8 pieces of Screws (F) through Seat (2) into Back (1), Brace Rail (5).
Tighten with Allen Wrench (G).
x8
F
x1
G
6
6
7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

MODWAY EEI-3678-NAT-TAU Assembly Instructions

Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI