Classic Exhibits GK-2002 Setup Instructions

Brand: Classic Exhibits

Model: GK-2002

Type: Setup Instructions

Classic Exhibits GK-2002 is a modular display system that can be used to create a variety of exhibit configurations. The system is made up of lightweight aluminum frames and panels that can be easily assembled and disassembled without tools. The GK-2002 is perfect for trade shows, conferences, and other events where you need to create a professional and eye-catching display.

Some of the features of the GK-2002 include:

Lightweight and easy to transport.
Modular design allows for a variety of configurations.
Tool-free assembly and disassembly.
Durable construction for long-lasting use.

Some of the features of the GK-2002 include:

Lightweight and easy to transport.
Modular design allows for a variety of configurations.
Tool-free assembly and disassembly.
Durable construction for long-lasting use.

Order #XXXXX

SETUP INSTRUCTIONS

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

GK-2002 General Layout

Plan View

20’

10’

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all setscrews

and locks during disassembly

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Gravitee Panel Assembly

Assembly Assembly Cont’d

Stacking Unstacking

Stacking Assembly

1) Place one horizontal frame on top of the other, lining up the

center grooves.

2) Turn stacking lock clockwise to tighten into place. Repeat

for each lock.

Stacking Disassembly

1) Turn the stacking lock counter-clockwise to loosen.

2) The whole spring on the stacking lock should be in view to

release each frame. The disengaged spring should release

the stacking lock. If not, keep turning the stacking lock until

it disengages.

Side-by-Side Assembly

1) Frames: Place frames side-by-side with one higher than the

other, then slide panel down to lock panels securely together.

2) Corner Connectors: Repeat Step 1 for installing corner

connectors to frames.

Side-by-Side Disassembly

1) Pull pin lock outwards to disengage.

2) Pull frames upward and apart at the same time to detatch.

Push stacking lock into the slot

of the upper frame, then spin the

cap to tighten the lock.

Push pin lock into hole of connecting frame.

Note: Block of pin lock will secure in groove.

Disengage the stacking lock by

spinning the cap counter

clockwise and pulling down.

Cap

Stacking

Lock

Pin Lock

Top View

Corner Connector

SEG

Grooves

Note: Orientation of Corner

Connector may change.

Order #XXXXX

Crate Packing

Crate 1 of 1

C B

Sintra

Graphic

1/4

2 3 6 8

12,13

Setup

Hardware

Charging Station

Countertop

Charging

Station

Base

Post

Graphics

Lights

Monitor

Mount

4,5

Setup Hardware

Step 1 of 4

Order #XXXXX

Backwall Assembly

Top View

Top

View

When assembled

Item

Qty.

Description

38”w x 95”h Gravitee Door Panel

95”h Gravitee Corner Post

94.5”h Gravitee Hinged Connector

46”w x 95”h Gravitee curved Panel

94.5”h Gravitee Hinged Connector

38”2 x 95”h Gravitee Panel

95”h Gravitee Corner Post

23”w x 95”h Gravitee Panel

46”w x 95”h Gravitee Panel

23”w x 95”h Gravitee curved Panel

42.6179”w Z45 Horizontal Extusion

Foot

Steps:

1) Assemble Gravitee panels & connectors together

in numerical order as shown.

2) Attach horizontal extrusions [14] inside panels [4] and [5].

3) Attach Boomerang Foot to Panel [13].

See Foot Attachment detail.

Foot Attachment

Bolt

Set

Screw

Foot

Vertical Extrusion

Slide Connectors

into groove of vertical

extrusion, then tighten

set screws to secure.

Attach foot with bolts.

Connector

Push pin lock into hole of connecting panel.

Note: Block of pin lock will secure in groove.

Pin Lock

Gravitee Panel Pin Locks

*****

***

Step 2 of 4

Order #XXXXX

Backwall Graphics

Front View

Steps:

1) Apply SEG graphics to front of assembled Backwall.

2) Insert Sintra graphic into assembled Backwall door frame.

3) Connect Sintra graphic to Velcro on front of assembled Backwall door section.

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab. Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

SEG Graphic Installation

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

aph

Step 3 of 4

Order #XXXXX

Backwall Attachments

When assembled

Steps:

1) Install Canopy Panels [A,B,C,D] to top of Gravitee

panels [1,4,5,7]. See Canopy Attachment detail.

2) Attach Lights to Backwall. See Light Connection detail.

3) Attach Monitor Mount to Backwall extrusions [14].

See Monitor Mount Attachment detail.

Canopy

Screw

Connector

Slide Connector into groove of horizontal

extrusion. Tighten set screws to secure

Connector. Insert screw through hole of

Canopy Panel and hole of Connector.

Tighten screw to secure.

Canopy Attachment

Item

Qty.

Description

12’ x 38” Canopy Panel

53.24” x 25.717“ Canopy Panel

12’ x 38” Canopy Panel

Connect Canopy Panels

together, using bolts

and wing nuts.

wing

nuts

bolts

Light Connection

Connect Lights to

Horizontal where

desired and

tighten in place.

Attach Monitor Mount to horizontal extrusions

using standoff barrels, bolts, and wing nuts.

*Monitor Mount Attachment

Bolts

Monitor

Mount

Standoff

Barrel

Wing

Nuts

Wing

Nuts

Step 4 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

Underside View

Base

Table Top

Post

Steps:

1) Connect base to post, using bolt.

2) Feed cord, from table top, through post and base.

3) Connect table top to post with fixed brackets, using bolts.

Completed Assembly

MOD-1430 Charging Table

Classic Exhibits GK-2002 Setup Instructions

Brand: Classic Exhibits

Model: GK-2002

Type: Setup Instructions

Some of the features of the GK-2002 include:

Lightweight and easy to transport.
Modular design allows for a variety of configurations.
Tool-free assembly and disassembly.
Durable construction for long-lasting use.

Download PDF

report

Classic Exhibits GK-2002 Setup Instructions

Classic Exhibits GK-2002 Setup Instructions

Related papers

Other documents