Eizo DX0212-IP User manual

Important

Please read this “User’s Manual”, and “PRECAUTIONS” (separate

volume) carefully to familiarize yourself with safe and eective

usage.

•For the latest product information including the “User’s Manual”,

refer to our web site :

www.eizoglobal.com

User’s Manual

Software Version 6.1

This product has been adjusted specically for use in the region to which it was originally shipped. If

operated outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by

any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless

prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every

eort has been made to ensure that this manual provides up-to-date information, please note that EIZO

product specications are subject to change without notice.

2

3

CONTENTS

CONTENTS ............................................................. 3

Chapter 1 Product Overview ............................. 5

1-1. Features ......................................................... 5

1-2. User level ....................................................... 7

1-3. System License ............................................. 7

Chapter 2 Live Image Screen /

Setting Screen Display ..................... 9

2-1. Displaying the Live Image Screen .............. 9

2-2. Displaying the Setting Screen ....................10

●When Using the Monitor Console ..................10

●When Using the Web Console .......................11

Chapter 3 Live Image Screen Operations ...... 12

3-1. Switch the Live Image Screen Layout .......12

●Display in full screen ......................................12

●Switch the screen layout ................................13

3-2. Switch the Page Displayed on the Live

Image Screen ................................................13

●Changing pages manually ..............................13

●Switching pages automatically

(Sequential display) ........................................14

3-3. Switch to Full Screen Display With 1

Screen Layout ..............................................14

3-4. Switch camera image display positions ...15

3-5. Operating Cameras ......................................16

3-6. Playing Back Video Saved on a

Camera’s SD Card ........................................18

Chapter 4 System Settings .............................. 22

4-1. Conrming the Basic Information ............ 22

4-2. Performing Network Settings .................... 24

4-3. Performing Communication Settings ...... 25

4-4. Setting the Date and Time ......................... 26

4-5. Conguring the Language ......................... 26

4-6. Initializing the System ................................ 27

4-7. Restarting the System ................................ 27

4-8. Updating Software ...................................... 28

4-9. Saving Settings Data .................................. 28

4-10. Loading System Settings Data .................. 29

4-11. Registering a License ................................. 30

4-12. Setting Event Rules .................................... 30

4-13. Registering a Server Certicate................ 34

4-14. Registering a Root Certicate ................... 34

4-15. Setting the Remote Control ID .................. 35

●Setting the product ID ................................... 35

●Setting the remote control ID ........................ 35

4-16. Conguring USB Device Hotkeys ............. 36

4-17. Setting IEEE 802.1X Authentication ...........37

4-18. Setting the product SNMP ......................... 38

4-19. Setting an IP Address Filter ....................... 40

4-20. Setting Failover ............................................41

●Failover Settings.............................................41

●Camera Registration ......................................41

●Camera Function Settings .............................42

●Display Position Settings ...............................42

●Overlay Settings .............................................42

●Preset Settings ...............................................42

4-21. Checking Logs ............................................ 43

4-22. Saving Logs ................................................. 43

4-23. Check basic Information ............................ 43

4-24. Save basic Information .............................. 43

4-25. Performing Camera Connection

Conrmation ................................................ 44

4-26.

Conrming Network Connection Status ...

44

4-27. Conguring Monitor Display Settings ...... 45

4-28. Performing Other Settings ........................ 45

4-29. Linking with a Qognify VMS ...................... 46

4-30. Streaming Gateway Function Settings

(DX0212-IP) ................................................... 46

●Streaming Gateway Settings .........................47

●Streaming Settings ........................................ 48

●Encoding Settings ......................................... 48

Chapter 5

Management of Network Cameras ...

50

5-1. Registering a Camera Using Auto

Discovery ..................................................... 50

5-2. Registering a Camera Manually .................51

5-3.

Changing Network Camera Information ...

55

5-4. Deleting Network Cameras ........................ 55

5-5.

Importing Network Camera Information ...

55

5-6. Setting Network Camera Time .................. 56

5-7. Setting Quality of Transmission Video

Images .......................................................... 57

5-8. Registering the Network Camera Preset

Position ........................................................ 59

Chapter 6 Live Image Screen Settings ........... 60

6-1. Setting Display Positions of Camera

Video Images ............................................... 60

6-2. Setting Display Methods of Camera

Video Images ............................................... 62

6-3. Setting Custom Screen Layouts ............... 63

6-4. Changing the Displayed Layout Icon ....... 64

6-5. Setting Layout Presets ............................... 65

6-6. Setting the Overlay ..................................... 67

6-7. Setting the Display Methods of Live

Image Screens ............................................. 69

4CONTENTS

6-8. Setting Current Monitor Display Status ... 69

6-9. Checking Livestream View .........................70

6-10. Updating the Camera Image of the Live

Image Screen to the Latest Status .............70

6-11. Performing Advanced Settings for

Camera Video ...............................................71

Chapter 7

Management of the User Account ...

72

7-1. Registering the User Account ................... 72

7-2. Changing the User Account ...................... 73

7-3. Deleting the User Account ......................... 73

7-4. Conguring Auto Login Settings ...............74

7-5. Performing LDAP Settings .........................74

Chapter 8 Reference ........................................ 76

8-1. Installation of Optional Arm

(FDF2712W-IP / FDF2312W-IP) ....................76

8-2. Connecting a Sub Monitor

(FDF2712W-IP / FDF2312W-IP) ................... 77

8-3. Specications ............................................. 78

●FDF2712W-IP .................................................78

●FDF2312W-IP................................................ 80

●DX0212W-IP .................................................. 82

8-4. Decoding Performance .............................. 83

●FDF2712W-IP / FDF2312W-IP ...................... 83

●DX0212W-IP .................................................. 83

8-5. Remote Control Specications ................. 85

8-6.

CSV File Format for Camera Registration ...

87

Appendix .............................................................. 88

Trademark ............................................................... 88

License .................................................................... 89

5

Chapter 1 Product Overview

This manual describes camera (network camera) settings, system settings, and product specications.

1-1. Features

●Communication with cameras

• Possible to receive video images from a 4K camera (3840 x 2160 / 30 fps)

• Possible to display video signals from cameras on a monitor

- Supports H.265, H.264, and MJPEG compression formats.

- Supports RTP, MPEG2-TS, and SRT transmission modes.

- A maximum of 48*1 cameras can be registered.

- Allows a free layout of video images (1 Screen, 3 Screens, 4 Screens, 9 Screens, 16 Screens,

32 Screens, 8 Screens, and Custom Screen) from multiple cameras.

- Supports Unicast and Multicast communication methods.

- Possible to switch the display position of camera video images while displaying video images.

- Allows playback of videos saved on a camera’s SD card.

*1 For FDF2312W-IP, the maximum number of cameras that can be registered in the factory setting (without enterprise

license registration) is 16.

●Streaming gateway function (DX0212-IP)

• “Merge mode” for streaming live image screen images

This mode converts the display of the live image screen into the RTSP or SRT protocol for streaming. By

streaming multiple camera images freely laid out on the screen (live image screen) as a single stream, it

reduces the network load.

• “Relay mode” for streaming individual camera images

In this mode, images received directly from each camera are streamed again without any processing using

the RTSP or SRT protocol. It allows increasing the number of streams without putting additional streaming

load on the cameras.

●Possible to output to monitors

• Supports FHD output to other monitors (1920 x 1080 / max. 60 fps) (FDF2712W-IP / FDF2312W-IP)

• Supports output to 4K monitors (3840 x 2160 / max. 60 fps) (DX0212-IP only)

●Supports multiple types of cameras

• Compatible with ONVIF® Prole S

• Supports camera control using camera manufacturer specic protocols

(When connecting Panasonic/i-PRO and AXIS cameras)

• Capable of receiving video streams from streaming servers such as VMS (Video Management

Software)

●System management

• Possible to register cameras or set the live image screen using a Web browser

• Possible to save and load settings data

Possible to save or load the setting data onto a computer.

6Chapter 1 Product Overview

●Event link function

• Event Rules

You can set actions to be executed as triggers for specic events.

●Various software extensions

• Icon Arranger

Allows you to rearrange or delete live screen layout menus.

• Livestream View

Allows you to check the screen displayed on the main unit on a Web browser.

• Screen orientation adjusting

The display direction of the system output video can be rotated to match the monitor installation direction

(horizontal or vertical).

• Failover

Allows automatic switching to a backup camera when communication with registered cameras is lost.

• Virtual PTZ

Even if the camera does not have PTZ functionality, this product enables PTZ operations by digitally

processing the camera images internally.

• Schedule function

You can schedule settings such as turning on/o the system power at a specic day/time.

●Security

• Comm. Error Detection

Allows displaying of a red frame alert message on the live image screen within a few seconds when

communication with cameras is lost.

• Lock function

Disables USB devices, front key operation, and remote control operation.

• Network security protocols

Supports protocols required for constructing high-level security systems including IEEE802.1X, SNMP, and

LDAP.

●Supports secure communication

Utilizes SSL and TLS, which are secure protocols. Communication between cameras and web pages

is encrypted using SSL.

Purchase an enterprise license to use LDAP authentication (refer to “1-3. System License” (page

7)).

●Support

• A 2-year long-term warranty for 24-hour continuous use

●Operation

• The live image screen can be controlled using a USB mouse, USB keyboard, remote control, or

joystick

7

Chapter 1 Product Overview

1-2. User level

There are three levels of user accounts that access this product. The operable range diers according to

the level of the user.

• ADMIN

• CAMERA CONTROL

• LIVE

The range of operation for each level is shown below.

√: Operable, -: Inoperable

Live Image Screen Setting

Screen

Switch layout

Switch

displayed

page

Switch

camera

image display

positions

Camera

control Playback

ADMIN √√√√√√

CAMERA

CONTROL √√√√√-

LIVE √ - - - - -

When the power is turned on and logged o, the user level is “LIVE”. For information on user level

settings, refer to “Chapter 7 Management of the User Account” (page 72).

In this manual, the following marks are used for operations with user level restrictions.

• Operation is only possible when the user level is “ADMIN”

User level “ADMIN”

• Operation is only possible when the user level is “ADMIN” or “CAMERA CONTROL”

There are two user levels: “ADMIN” and “CAMERA CONTROL”

1-3. System License

This product has features that can be used by applying a paid system license. The types of system

licenses are as follows. For details, contact your dealer or local EIZO representative.

• Enterprise license

• SRT extended functionality license*1

• Failover extended functionality license*1

• Playback extended functionality license*1

• Qognify extended functionality license*1

*1 This can be applied when an enterprise license is registered.

You can check the application status of the system license on the setting screen after logging in (refer to

“2-2. Displaying the Setting Screen” (page 10)reference). For information on registering a system

license, refer to “4-11. Registering a License” (page 30).

8Chapter 1 Product Overview

In this manual, the following marks are used for features that require a paid system license.

• Available only if an “Enterprise License” is applied

Enterprise license

• Available only when “SRT extended functionality license” is applied

SRT extended functionality license

• Available only when “Failover extended functionality license” is applied

Failover extended functionality license

• Available only when “Playback extended functionality license” is applied

Playback extended functionality license

• Available only when “Qognify extended functionality license” is applied

Qognify extended functionality license

9

Chapter 2 Live Image Screen / Setting Screen Display

Chapter 2 Live Image Screen / Setting

Screen Display

2-1. Displaying the Live Image Screen

1.

Press the power button ( ) on the front of the product.

Note

• For FDF2712W-IP / FDF2312W-IP, check that the main power switch on the back is turned on.

The power indicator lights up blue and the live image screen is displayed.

Live Image Screen Layout

Display mode menu System menu

Image display area

• When no camera is registered, a “Not registered” message is displayed.

• When an input signal is not supported, the “Unsupported Resolution” message is displayed.

Camera control menu

10 Chapter 2 Live Image Screen / Setting Screen Display

2-2. Displaying the Setting Screen

User level “ADMIN”

The setting screen can be operated using the monitor console (screen displayed on the monitor) or the

web console (screen displayed on the browser).

To display the setting screen, it is necessary to log in as a user with a user level of “ADMIN”.

Note

• The default settings of the user account are as follows.

-Username: “admin”

- Password: “admin”

- User level: “ADMIN”

• For information on user levels, refer to “1-2. User level” (page 7).

• It is recommended that you log out after completing the setup, so as to prevent a third party from operating the

camera or altering the settings.

• When the Auto Login settings are congured, it is possible to log in to the system without the username and

password (refer to “7-4. Conguring Auto Login Settings” (page 74)).

●When Using the Monitor Console

Use a USB mouse to perform operations. You cannot operate the setting screen with the remote

control.

Note

• Clicking an item that requires characters to be input will display a software keyboard.

1.

On the live image screen, click the login icon ( ).

2.

Enter a username and a password.

Note

• When the “Account Type” is set to “LDAP”, you can select the account type when logging in by checking “Allow

choosing of account type on the login dialog” under “LDAP” in advance (refer to “7-5. Performing LDAP

Settings” (page 74)).

3.

Click “Login”.

The setting icon ( ) can then be selected.

4.

Click the setting icon ( ).

11

Chapter 2 Live Image Screen / Setting Screen Display

●When Using the Web Console

Use a computer connected to the network to perform operations.

Note

• Microsoft Edge 79 or later is recommended for the web browser.

1.

Launch the browser.

2.

Enter the following address to access the site.

Address: http://<IP address of this product>/

In the default settings, the IP address is http://192.168.0.150/.

3.

Enter a username and a password.

4.

Click “OK”.

The setting screen is displayed.

Note

• If you are unable to login, try using the following address. http://<IP address of this product>/index.html

Setting Screen Layout

Sub menuSetting menu

Setting menu (web console)

Note

• For the monitor console, “Return” is displayed instead of “Logout”.

12 Chapter 3 Live Image Screen Operations

Chapter 3 Live Image Screen Operations

The live image screen can be operated with a USB mouse, USB keyboard, remote control, or joystick.

• USB keyboard and remote control operations

Item USB keyboard Remote control

To select an item Arrow keys / / /

To set a selected item Enter key

When deselecting a camera Escape key

3-1. Switch the Live Image Screen Layout

Set the number of camera images to be displayed simultaneously on the live image screen.

●Display in full screen

1.

Click .

The menu is hidden and the image is displayed on the entire screen. To display the menus again,

double-click any place on the screen.

Note

• You can also use the following methods to perform this operation.

- USB keyboard: Shortcut key (F)

- Remote control:

13

Chapter 3 Live Image Screen Operations

●Switch the screen layout

1.

Click the icon for the layout you want to view.

The screen layout changes by selecting the layout icon in the display mode menu.

Note

• When using a 3 screens layout, the camera must be congured to display vertical images. For details, refer to

the User’s Manual of the camera.

• You can also use the following methods to perform this operation.

- USB keyboard: Shortcut key (L)

- Remote control:

• If you have an enterprise license registered, you can change the layout icon to display (refer to “6-4. Changing

the Displayed Layout Icon” (page 64)).

3-2. Switch the Page Displayed on the Live Image

Screen

Switch the page to display the camera image. Pages can be changed over either manually or

automatically at a set interval (sequential display).

●Changing pages manually

1.

Click or in the display mode menu.

Example: 4-screen layout with 16 registered cameras

Camera 1 Camera 2

Camera 3 Camera 4

Camera 5 Camera 6

Camera 7 Camera 8

Camera 9 Camera 10

Camera 11 Camera 12

Camera 13 Camera 14

Camera 15 Camera 16

Note

• You can also use the following methods to perform this operation.

- USB keyboard: Shortcut key (PageDown or PageUp)

- Remote control: or

14 Chapter 3 Live Image Screen Operations

●Switching pages automatically (Sequential display)

1.

Click in the display mode menu.

Pages displayed on the screen are changed over automatically at a specied interval.

Note

• You can change the page switching interval on the settings screen (refer to “6-2. Setting Display Methods of

Camera Video Images” (page 62)). The default setting is 10 seconds

• To stop sequence display, click again.

• Click the camera image to stop the sequence display.

• You can also use the following methods to perform this operation.

- USB keyboard: Shortcut key (S)

- Remote control:

3-3. Switch to Full Screen Display With 1 Screen Layout

Toggles between the current display state and full screen display with a 1 screen layout. Use a USB

mouse to perform operations. It cannot be operated with a USB keyboard or remote control.

1.

With the menu displayed, double-click on the camera image you want to

display in full screen.

Switches to a full screen display of the 1 screen layout. Double-click the camera image to return to

the original display state.

Note

• This function is disabled while in Joystick mode.

15

Chapter 3 Live Image Screen Operations

3-4. Switch camera image display positions

There are two user levels: “ADMIN” and “CAMERA CONTROL”

If the image layout is displayed in multiple screens other than one screen, camera image display positions

can be switched. Use a USB mouse to perform operations. It cannot be operated with a USB keyboard or

remote control.

1.

Select a camera image to move using the USB mouse and drag the image and

drop it on the desired camera image position.

The display positions of the source and destination camera images are switched.

16 Chapter 3 Live Image Screen Operations

3-5. Operating Cameras

There are two user levels: “ADMIN” and “CAMERA CONTROL”

Attention

• Not all features may be available. For functions that are not available from this product or do not work as

expected, please operate them on the camera side.

Browse

• The display position of the camera image can be changed in the settings screen (refer to “6-1. Setting Display

Positions of Camera Video Images” (page 60)).

1.

From the “Camera” list box, select the camera you wish to operate.

The frame of the selected camera image will be highlighted in light blue.

Note

• You can also select the camera to operate using the following methods.

- Enter the screen number with the number keys on a USB keyboard

- Enter the screen number with the number buttons on the remote control

- Click the camera image with a USB mouse

2.

Operate the functions.

17

Chapter 3 Live Image Screen Operations

Function Description

Brightness Adjusts the camera brightness.

:The image becomes darker.

:Returns the brightness to the default setting.* 1

:The image becomes brighter.

Preset Moves the camera orientation to the position registered in advance.

Select to move the camera orientation to the home position.

Focus* 4 Adjusts the camera focus.

:Moves the focus point closer.* 2

:Adjusts the focus point automatically.* 3

:Moves the focus point farther away.* 2

PTZ: Target

selection

Selects the target for the PTZ operation.

Virtual: Performs the PTZ operation by digitally processing the camera images inside the

product.

Camera: Perform PTZ operations using camera functions on the camera.

Note

• If you select “Virtual,” PTZ operations are available regardless of the “Protocol” settings

of the camera. However, the following limitations apply.

- Joystick Mode cannot be enabled.

- When the compression format is MJPEG, PTZ operations are not available.

PTZ: Joystick

Mode

Enable when you want to continuously perform PTZ operation of a camera.

:Joystick Mode is disabled.

:Joystick Mode is enabled.

Attention

• If the PTZ target is set to “Virtual,” Joystick Mode cannot be enabled.

Note

• You can also use the following methods to perform this operation.

- USB keyboard: Shortcut key (J)

- Joystick (T8311): R button

PTZ: Zoom Adjusts the camera display magnication.

:Zooms out.

:Zooms in.

Note

• You can also use the following methods to perform this operation.

- USB keyboard: Shortcut key (+ or -)

- Remote control: or

• If Joystick Mode is enabled, you can also use the following methods to perform this

operation.

- Joystick (T8311): Rotate knob

- USB mouse: Rotate the wheel button

18 Chapter 3 Live Image Screen Operations

Function Description

PTZ: Position Adjusts the horizontal position (pan) and vertical position (tilt) of the camera.

Note

• You can also use the following methods to perform this operation.

- USB keyboard, Shortcut keys (Ctrl + Up arrow key, Ctrl + Down arrow key, Ctrl + Left

arrow key, or Ctrl + Right arrow key)

• If Joystick Mode is enabled, you can also use the following methods to perform this

operation.

- Joystick (T8311): Tilt the stick

- USB mouse: Move the mouse while clicking the left button

PTZ: PTZ Adjust Adjusts the movement amount of the PTZ operation. The movement amount increases as

the slider moves to the right.

Note

• When using a USB keyboard, pressing the shortcut keys (Ctrl and - or Ctrl and +)

adjusts the PTZ adjust.

Auxiliary

Command

Operates the auxiliary functions of a camera, or executes actions of registered event

rules.

1. Select the “Auxiliary Command” list box.

2. Select .

Note

• The auxiliary functions of a camera can only be operated with specic devices whose

protocol is set to “ONVIF” or “Panasonic/i-PRO”.

• Event rule events can only be executed when a camera is not selected.

*1 Cannot be set for cameras in which “Protocol” or “AXIS®”.

*2 If using a camera in which “Protocol” is set to “ONVIF” or “AXIS”, the mode is switched to manual

adjustment mode.

*3 If using a camera in which“Protocol” is set to “ONVIF” or “AXIS” the mode is switched to automatic

adjustment mode.

*4 Cannot be set for cameras in which “Protocol” is set to “AXIS”.

Note

• If you select a camera image in the image display area, you can perform PTZ operation using the buttons

superimposed on the image.

3-6. Playing Back Video Saved on a Camera’s SD Card

Enterprise license

Playback extended functionality license

There are two user levels: “ADMIN” and “CAMERA CONTROL”

Video saved on a camera’s SD card can be played back on the Playback screen.

19

Chapter 3 Live Image Screen Operations

Attention

• If this feature is enabled, you will see the “Playback” and “Live” tabs.

• If the video clock is not correctly displayed, check the time zone settings of the product main unit and the

network camera.

• Playback is not supported for les recorded in MJPEG.

• Can only be used when “Protocol” is set to “Panasonic/i-PRO” or “AXIS”.

• The following restrictions apply when “Protocol” is set to “Panasonic/i-PRO”.

- If the Date Filter is not enabled, up to 50 les are displayed in the “Recording Date” list starting from the oldest

le.

- One recording may be split into multiple les.

- Only les recorded as recording stream 1 on the network camera can be played.

- If the recording compression format is JPEG, playback will fail.

- For multi-sensor cameras, only the channels set in the camera registration can be played.

• The following restrictions apply when “Protocol” is set to “AXIS”.

-If the Date Filter is not enabled, up to 50 les are displayed in the “Recording Date” list starting from the newest

le.

-Since one recording will become a single le, longer recordings will have a large le size and playback may not

be possible.

- Since one recording will become a single le, the le does not appear in the “Recording Date” list until the

recording has stopped. If you set up the network camera using the following procedure, you can continue

recording while splitting les at set intervals.

1. Create a pulse in the event function “Schedule”, and set the interval to 2 minutes (when dividing the video

every 2 minutes).

2. In the event function “Rules”, set “Condition” to one created pulse event, set “Action” to “Video Recording”,

set “Pre-Buer” to “01”, set “Post-Buer” to “01:59”, and save.

1.

Select “Playback”.

2.

From the “Camera Name” list box, select the camera.

Note

• If the “Failover” extended functionality license is valid, “Switch To Failover Cameras” is displayed. When

“Switch to Failover Cameras” is enabled, the cameras that can be selected will switch to those registered for

failover.

20 Chapter 3 Live Image Screen Operations

3.

Select the video le to playback from the “Recording Date” list box.

Up to 50 les can be displayed in the “Recording Date” list box (les being recorded are not

displayed). You can also select the previous le with and select the next le with .

By using the date lter function ( lter icon), you can lter the videos displayed in the “Recording

Date” list box by date.

Date lter

Enable “Date Filter”, and specify the date. Click “OK” to display up to 50 videos in the “Recording Date”

list box starting from the specied date.

4.

Press .

The video le will start downloading and the video will be played when downloading is complete.

Attention

• If the video le is a large size, the download may be interrupted and video playback may not be possible.

Page is loading ...

Eizo DX0212-IP User manual

This manual is also suitable for

Eizo DX0212-IP User manual

Related papers

Other documents