Panasonic WHUH12DE8 Operating instructions

Brand: Panasonic

Model: WHUH12DE8

Type: Operating instructions

This manual is also suitable for

Model br.

Unutarnja jedinica

WH-SHF09D3E8

WH-SHF12D9E8

HRVATSKI 2 ~ 9

Prije rukovanja uređajem pažljivo pročitajte ove upute za uporabu i sačuvajte ih za buduću uporabu.

Prije korištenja uređaja provjerite je li ovlašteni dobavljač ispravno proveo instalaciju, precizno prateći sljedeće upute za

instalaciju.

F568675

Sdn. Bhd. 2012. Neovlaštenim kopiranjem i

distribucijom kršite zakon.

Vanjska jedinica

WH-UH09DE8

WH-UH12DE8

F567972

Operating Instructions

Air-to-Water Heatpump

Model No.

Indoor Unit

Outdoor Unit

WH-SXF09D3E5 WH-UX09DE5

WH-SXF12D6E5 WH-UX12DE5

Unauthorized copying and distribution is a violation

of law.

ENGLISH

Before operating the unit, read these operating instructions thoroughly and keep them for future reference.

Before operating the unit, make sure the installation has been carried out correctly by authorized dealer correctly and

precisely following the installation instructions given.

2 ~ 9

FRANÇAIS

Avant d’utiliser l’appareil, lisez ce mode d’emploi dans son intégralité et conservez-le pour toute référence ultérieure.

Avant de faire fonctionner l’unité, assurez-vous que l’installation a été correctement réalisée par un revendeur agréé

et dans le strict respect des consignes d’installation fournies.

10 ~ 17

ESPAÑOL

Antes de utilizar la unidad, sírvase leer atentamente estas instrucciones de funcionamiento y conservarlas como

futuro elemento de consulta.

Antes de operar la unidad asegúrese de que la instalación haya sido realizada correctamente por un instalador

autorizado, siguiendo de forma correcta y precisa las instrucciones de instalación dadas.

18 ~ 25

DEUTSCH

Bevor Sie das Gerät in Betrieb nehmen, lesen Sie bitte diese Bedienungsanleitung aufmerksam durch und bewahren Sie

sie für die künftige Verwendung auf.

Vor der Inbetriebnahme dieses Geräts ist sicherzustellen, dass die Montage durch einen autorisierten Händler

fachgerecht entsprechend der Installationsanleitung durchgeführt wurde.

26 ~ 33

ITALIANO

Prima di utilizzare l’unità si prega di leggere attentamente le istruzioni e di conservare questo opuscolo per potervi

fare riferimento in futuro.

Prima di far funzionare l’unità, assicurarsi che l’installazione sia stata eseguita correttamente da un rivenditore

autorizzato e seguendo precisamente le istruzioni date per l’installazione

34 ~ 41

NEDERLANDS

Lees voor u het apparaat gebruikt deze gebruiksaanwijzing grondig en bewaar deze voor toekomstig gebruik.

Controleer, voor u de unit in gebruik neemt, dat de installatie goed is uitgevoerd door een of ciële dealer en dat dat

nauwkeurig is gedaan volgens de verstrekte instructies voor de installatie.

42 ~ 49

PORTUGUÊS

Antes de ligar a unidade, leia cuidadosamente este manual de utilização e guarde-o para futura referência.

Antes de colocar a unidade em funcionamento, ceritifque-se que a instalação foi feita correctamente por um

fornecedor autorizado e que seguiu com precisão as instruções de instalação dadas.

50 ~ 57

EΛΛΗΝΙΚΆ

Προτού θέσετε τη μονάδα σε λειτουργία, διαβάστε προσεκτικά αυτές τις οδηγίες χρήσης και φυλάξτε τις για μελλοντική αναφορά.

Πριν θέσετε σε λειτουργία τη μονάδα, βεβαιωθείτε ότι η εγκατάσταση έχει διεξαχθεί κανονικά από εξουσιοδοτημένο

αντιπρόσωπο, ο οποίος έχει ακολουθήσει σωστά και πιστά τις δοθείσες οδηγίες.

58 ~ 65

БЪЛГАРСКИ

Преди да задействате климатика, прочетете внимателно инструкциите за употреба и ги запазете за бъдещи справки.

Преди да използвате устройството се уверете, че монтажът е извършен правилно и прецизно от оторизиран дилър,

като са спазвани инструкциите за монтаж.

66 ~73

0.2

0.40

0.30.1

MPa

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

OFF

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MONTUEWEDTHUFRISAT SUN

SOLAR REMOTE

NOT AVAILABLE

2 3 4 5 6

OFF

F567972

Operating Instructions

Air-to-Water Heatpump

Model No.

Indoor Unit

Outdoor Unit

WH-SXF09D3E5 WH-UX09DE5

WH-SXF12D6E5 WH-UX12DE5

Unauthorized copying and distribution is a violation

of law.

ENGLISH

Before operating the unit, read these operating instructions thoroughly and keep them for future reference.

Before operating the unit, make sure the installation has been carried out correctly by authorized dealer correctly and

precisely following the installation instructions given.

2 ~ 9

FRANÇAIS

Avant d’utiliser l’appareil, lisez ce mode d’emploi dans son intégralité et conservez-le pour toute référence ultérieure.

Avant de faire fonctionner l’unité, assurez-vous que l’installation a été correctement réalisée par un revendeur agréé

et dans le strict respect des consignes d’installation fournies.

10 ~ 17

ESPAÑOL

Antes de utilizar la unidad, sírvase leer atentamente estas instrucciones de funcionamiento y conservarlas como

futuro elemento de consulta.

Antes de operar la unidad asegúrese de que la instalación haya sido realizada correctamente por un instalador

autorizado, siguiendo de forma correcta y precisa las instrucciones de instalación dadas.

18 ~ 25

DEUTSCH

Bevor Sie das Gerät in Betrieb nehmen, lesen Sie bitte diese Bedienungsanleitung aufmerksam durch und bewahren Sie

sie für die künftige Verwendung auf.

Vor der Inbetriebnahme dieses Geräts ist sicherzustellen, dass die Montage durch einen autorisierten Händler

fachgerecht entsprechend der Installationsanleitung durchgeführt wurde.

26 ~ 33

ITALIANO

Prima di utilizzare l’unità si prega di leggere attentamente le istruzioni e di conservare questo opuscolo per potervi

fare riferimento in futuro.

Prima di far funzionare l’unità, assicurarsi che l’installazione sia stata eseguita correttamente da un rivenditore

autorizzato e seguendo precisamente le istruzioni date per l’installazione

34 ~ 41

NEDERLANDS

Lees voor u het apparaat gebruikt deze gebruiksaanwijzing grondig en bewaar deze voor toekomstig gebruik.

Controleer, voor u de unit in gebruik neemt, dat de installatie goed is uitgevoerd door een of ciële dealer en dat dat

nauwkeurig is gedaan volgens de verstrekte instructies voor de installatie.

42 ~ 49

PORTUGUÊS

Antes de ligar a unidade, leia cuidadosamente este manual de utilização e guarde-o para futura referência.

Antes de colocar a unidade em funcionamento, ceritifque-se que a instalação foi feita correctamente por um

fornecedor autorizado e que seguiu com precisão as instruções de instalação dadas.

50 ~ 57

EΛΛΗΝΙΚΆ

αντιπρόσωπο, ο οποίος έχει ακολουθήσει σωστά και πιστά τις δοθείσες οδηγίες.

58 ~ 65

БЪЛГАРСКИ

Преди да използвате устройството се уверете, че монтажът е извършен правилно и прецизно от оторизиран дилър,

като са спазвани инструкциите за монтаж.

66 ~73

0.2

0.40

0.30.1

MPa

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

OFF

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MONTUEWEDTHUFRISAT SUN

SOLAR REMOTE

NOT AVAILABLE

2 3 4 5 6

OFF

Upute za uporabu

Toplinska crpka zrak-voda

• Panasonicova

toplinska crpka zrak-voda

odijeljeni je sustav koji

se sastoji samo od vanjske jedinice i unutarnje jedinice. Sustav je

osmišljen za korištenje u kombinaciji s Panasonicovim spremnikom. U

slučaju da se uz Panasonicov

sustav toplinske crpke zrak-voda

koristi spremnik koji nije Panasonicov, Panasonic ne može jamčiti ni

pouzdan rad niti pouzdanost sustava.

• U ovom je priručniku opisano kako se koristi sustav toplinske crpke

samo između vanjske i unutarnje jedinice.

• Detalje o radu ostalih dijelova, kao što je spremnik za vodu, radijator,

termostat i podni sustav, potražite u korisničkim priručnicima

proizvođača te opreme.

Radi sprečavanja samoozljeđivanja, ozljeđivanja drugih osoba ili štete na

imovini, pridržavajte se sljedećeg.

Neispravne radnje koje su rezultat nepridržavanja ovih uputa mogu izazvati

ozlijede ili štetu koja po ozbiljnosti može biti:

Zahvaljujemo vam na kupnji

Panasonicova proizvoda.

Ilustracije navedene u ovim uputama služe

samo radi objašnjenja i mogu se razlikovati od

stvarnog uređaja. Podložne su promjenama bez

prethodne obavijesti radi budućih poboljšanja.

Temperatura izlaza za

vodu (°C)

Unutarnji

GRIJANJE

Maks. 65

Min. 25

Temperatura okoline

(°C)

Vanjski

GRIJANJE

Maks. 35

Min. -20

NAPOMENA:

Kada je vanjska temperatura iznad

temperaturnog raspona, kapacitet grijanja

značajno će se smanjiti i vanjska će jedinica

možda prestati s radom kako bi se izvršila

sigurnosna kontrola.

Uređaj će se automatski ponovno pokrenuti

kratko nakon što se unutarnja temperatura

vrati u granice.

U slučaju kad je vanjska temperatura iznimno

niska, potreban je rad pomoćnoga grijača.

SADRŽAJ

NAPOMENA

UVJETI RADA

MJERE OPREZA

2~3

UPRAVLJAČKA PLOČA

4~7

UNUTARNJA JEDINICA

U SLUČAJU PROBLEMA

INFORMACIJE

MJERE OPREZA

Ovaj znak upozorava na

smrtonosne ili ozbiljne ozljede.

Ovaj znak označava mogućnost

ozljede ili oštećenja imovine.

Upute koje je potrebno slijediti podijeljene su prema sljedećim simbolima:

Ovaj simbol označava radnju

koja je ZABRANJENA.

Ovi simboli predstavljaju

radnju koja je OBAVEZNA.

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

UPOZORENJE

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

OPREZ

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

VANJSKA JEDINICA I UNUTARNJA JEDINICA

Ovim uređajem ne smiju rukovati osobe (uključujući djecu) sa

smanjenim zičkim, osjetilnim ili mentalnim sposobnostima ili

s nedovoljnim iskustvom i znanjem, osim ako se takve osobe

nalaze pod nadzorom ili ih u uporabu ovoga uređaja upućuju

osobe odgovorne za njihovu sigurnost. Nadgledajte djecu i

nemojte im dopustiti da se igraju ovim uređajem.

Obratite se ovlaštenom dobavljaču ili stručnjaku za čišćenje

unutarnjih dijelova, popravke, instalaciju, uklanjanje i ponovnu

instalaciju uređaja. Neispravna instalacija i rukovanje mogu

dovesti do curenja, električnog udara ili požara.

Savjetujte se s ovlaštenim dobavljačem ili stručnjakom o

uporabi navedene vrste rashladnog sredstva. Uporaba

rashladnog sredstva osim navedene vrste može izazvati

oštećenje proizvoda, eksploziju i ozljedu itd.

Nemojte postavljati uređaj na mjesto na kojem postoji

opasnost od eksplozije ili može doći do zapaljenja. Moglo bi

doći do požara.

Ne gurajte prste ili druge predmete u unutarnju

ili vanjsku jedinicu, dijelovi koji se rotiraju mogu

izazvati ozljedu.

Ne dirajte vanjsku jedinicu kada sijeva da ne bi došlo do

električnog udara.

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

UPOZORENJE

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

HRVATSKI

NAPAJANJE

Nemojte sjedati ili stajati na

uređaj, možete slučajno pasti.

Nemojte postavljati unutarnju jedinicu u

vanjski prostor. Predviđena je samo za

instalaciju u unutarnji prostor.

NAPAJANJE

Da ne bi došlo do pretjeranog

zagrijavanja ili vatre, nemojte

koristiti modicirani kabel,

produžni kabel, dupli kabel ili

nepoznati kabel.

Sprečavanje pregrijavanja, vatre ili električnog

udara:

• Nemojte ovaj uređaj spajati na istu utičnicu

s nekom drugom opremom.

• Ne dirajte uređaj mokrim rukama.

• Nemojte previše rastegnuti kabel za napajanje.

Ako je kabel napajanja oštećen, mora ga

zamijeniti proizvođač, serviser proizvođača

ili slično kvalicirane osobe da bi se izbjegle

moguće opasnosti.

Ovaj je uređaj opremljen sklopkom Residue

Current Circuit Breaker (RCCB). Snažno

preporučujemo da provjerite rad osigurača

RCCB nakon što ga instalirate te periodički,

nakon što ovlašteni dobavljač provede

servisiranje ili održavanje, kako biste

se uvjerili u ispravni rad. U suprotnome,

neispravan rad može izazvati električni udar.

Izričito preporučujemo instaliranje sklopke na

diferencijalnu struju (RCD) na lokaciji da bi se

spriječio električni udar ili požar.

Prestanite koristiti uređaj kada dođe do

poremećaja u radu/kvara i isključite mrežni utikač

ili isključite napajanje i strujno-zaštitnu sklopku.

(Opasnost od dima/vatre/električnog udara)

Primjeri nepravilnosti/kvara

• Sklopka RCCB se sama isključuje.

• Za vrijeme rada uređaja iz njega se širi miris

paljevine, neobični zvukovi ili vibracije.

• Vruća voda se izlijeva iz uređaja.

Odmah se obratite svom lokalnom dobavljaču

radi održavanja/popravka.

Preporučuje se nošenje rukavica tijekom

servisiranja ili održavanja uređaja radi

izbjegavanja opasnosti.

Ova oprema mora biti uzemljena da bi se

spriječio strujni udar ili vatra.

Spriječite strujni udar tako da isključite

napajanje i iskopčajte:

– Prije čišćenja ili servisiranja.

– Dugog nekorištenja.

Uređaj služi za višestruku upotrebu. Svi strujni

krugovi trebaju biti isključeni prije nego što

pristupite priključcima unutarnje jedinice kako

biste spriječili strujni udar, opekline ili smrtne

ozljede.

VANJSKA JEDINICA I UNUTARNJA JEDINICA

Vanjsku jedinicu ne perite vodom, benzinom,

razrjeđivačom ili erozivnim puderom.

Nemojte postavljati uređaj blizu zapaljive

opreme ili u kupaonici. Može doći do

električnog udara ili vatre.

Ne dirajte cijev za ispust vode na unutarnjoj

jedinici za vrijeme rada.

Nemojte stavljati nikakve predmete na uređaj ili

ispod njega.

Ne dirajte oštro aluminijsko rebro,

oštri vas dijelovi mogu ozlijediti.

Nemojte koristiti sustav tijekom sterilizacije.

Tako ćete spriječiti isparavanje ili pregrijavanje

tijekom tuširanja.

Provjerite je li odvodna cijev pravilno spojena.

Može doći do curenja.

Nakon duljeg razdoblja uporabe pazite

da rešetka na koju je uređaj montiran ne

propadne kako uređaj ne bi pao.

Postavke polja sterilizacijske funkcije mora

kongurirati ovlašteni dobavljač u skladu s

lokalnim zakonima i propisima.

UPRAVLJAČKA PLOČA

Pazite da u upravljačku ploču ne dospije tekućina.

Može doći do električnog udara ili vatre.

Nemojte pritiskati gumbe na upravljačkoj ploči

tvrdim, zašiljenim predmetima. Može doći do

oštećenja uređaja

Unutarnju jedinicu ne perite vodom, benzinom,

razrjeđivačom ili erozivnim puderom.

Nemojte sami pokušavati pregledavati i

servisirati upravljačku ploču. Posavjetujte

se s ovlaštenim dobavljačem. Neispravno

rukovanje može uzrokovati povrede.

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

UPOZORENJE OPREZ

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene,

thinner or scouring powder to avoid damage or

corrosion at the unit.

Do not use for preservation of precise

equipment, food, animals, plants, artwork

or other objects. This may cause quality

deterioration, etc.

Do not use any combustible equipment in front of

the air ow outlet to avoid  re propagation.

Do not expose plants or pet directly to air ow to

avoid injury, etc.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing

the  oor. After waxing, aerate the room properly

before operating the unit.

Do not install the unit in oily and smoky areas to

prevent damage to the unit.

Do not dismantle the unit for cleaning purpose to

avoid injury.

Do not step onto an unstable bench when

cleaning the unit to avoid injury.

Do not place a vase or water container on the

unit. Water may enter the unit and degrade the

insulation. This may cause an electric shock.

Do not open window or door for long time during

COOL/DRY mode operation.

Ensure drainage pipe is connected properly and

keep drainage outlet clear of gutters, containers

or does not immersed in water to prevent water

leakage.

After a long period of use or use with any

combustible equipment, aerate the room

regularly.

After a long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

REMOTE CONTROL

Do not use rechargeable (Ni-Cd) batteries.

It may damage the remote control.

To prevent malfunction or damage of the remote

control:

• Remove the batteries if the unit is not going to

be used for a long period of time.

• New batteries of the same type must be

inserted following the polarity stated.

POWER SUPPLY

Do not pull the cord to disconnect the plug to

prevent electric shock.

WARNING

POWER SUPPLY

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

It is strongly recommended to be installed

with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD) to prevent

electric shock or  re.

To prevent overheating,  re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically

wiped with a dry cloth.

Stop using the product if any abnormality/failure

occurs and disconnect the power plug or turn off

the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it is

switched on for operation.

• The fan does not stop even if the operation is

stopped.

Contact your local dealer immediately for

maintenance/repair.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply and unplug when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity.

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

SAFETY PRECAUTIONS

To prevent personal injury, injury to others, or property

damage, please comply with the following.

Incorrect operation due to failure to follow instructions below

may cause harm or damage, the seriousness of which is

classi ed as below:

WARNING

This sign warns of death or serious injury.

CAUTION

This sign warns of injury or damage to property.

The instructions to be followed are classi ed by the following

symbols:

This symbol denotes an action that is PROHIBITED.

These symbols denote an actions that is

COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. Children should be supervised to

ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to

clean the internal parts, repair, install, remove

and reinstall the unit. Improper installation and

handling will cause leakage, electric shock or

 re.

Con rm to authorized dealer or specialist on

usage of speci ed refrigerant type. Using of

refrigerant other than the speci ed type may

cause product damage, burst and injury etc.

Do not install the unit in a potentially explosive

or  ammable atmosphere. Failure to do so could

result in  re.

Do not insert your  ngers or other

objects into the air conditioner indoor

or outdoor unit, rotating parts may

cause injury.

Do not touch the outdoor unit during lightning, it

may cause electric shock.

Do not expose yourself directly to cold air for a

long period to avoid excess cooling.

Do not sit or step on the unit, you may

fall down accidentally.

REMOTE CONTROL

Do not allow infants and small children to play

with the remote control to prevent them from

accidentally swallowing the batteries.

POWER SUPPLY

Do not use a modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or

pulling out the power plug.

Air Inlet

Air Outlet

Air Inlet

Remote

Control

Power

Supply

Indoor

Unit

Outdoor

Unit

ENGLISH

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water,

benzene, thinner or scouring powder.

Do not install the unit close to any combustible

equipment or at bathroom. Otherwise, it may

cause electric shock or  re.

Do not touch the water discharge pipe at the

indoor unit during operation.

Do not place anything on top or beneath of the

unit.

Do not touch the sharp aluminium  n,

sharp parts may cause injury.

Ensure drainage pipe is connected properly.

Otherwise, leakage may occur.

After long period of use, make sure the

installation rack does not deteriorate to prevent

the unit from falling down.

CONTROL PANEL

Do not let the control panel get wet. Otherwise,

it may cause electric shock or  re.

Do not press the buttons on the control panel

with hard, pointed objects. Otherwise, it may

damage the unit.

Do not wash the control panel with water,

benzene, thinner or scouring powder.

not inspect or service the control panel by

yourself. Please consult authorized dealer.

Otherwise, it may cause injury if mishandling.

WARNING

POWER SUPPLY

Do not use modi ed cord,

joint cord, extension cord or

unspeci ed cord to prevent

overheating and  re.

To prevent overheating,  re or electric shock:

• Do not share the same power outlet with other

equipment.

• Do not operate with wet hands.

• Do not over bend the power supply cord.

If the supply cord is damage, it must be replaced

by the manufacturer, its service agent or similarly

quali ed persons in order to avoid a hazard.

This unit is equipped with Residue Current Circuit

Breaker (RCCB). It is strongly recommended to

check the operation of the RCCB after installation

and periodically after servicing or maintenance by

authorized dealer to ensure it is in good working

order. Otherwise, it may cause electrical shock or

 re in case of malfunction.

It is strongly recommended to install Residual

Current Device (RCD) on-site to prevent electric

shock or  re.

Stop using the product when any abnormality/

failure occurs and disconnect the power plug or

turn off the power switch and breaker.

(Risk of smoke/ re/electric shock)

Examples of abnormality/failure

• The RCCB switches off by itself.

• Burning smell, abnormal noise or vibration

sound is observed when the unit is in use.

• Hot water keeps on coming off the unit.

Contact immediately your local dealer for

maintenance/repair.

It is recommended to wear gloves during servicing

or maintenance in order to avoid hazard.

This equipment must be earthed to prevent

electrical shock or  re.

Prevent electric shock by switching off the power

supply when:

- Before cleaning or servicing.

- Extended non-use.

This appliance is for multiple uses. All power

supply circuits must be turn off before access to

any of the terminals in the indoor unit, to avoid

electrical shock, burn or fatal injury.

Panel

Power Supply

Floor Heating

Control Panel

Indoor Unit

Shower

Outdoor Unit

Water Tank Unit

Unutarnja

jedinica

Napajanje

Grijanje poda

Tuš

Zaslon

Vanjska jedinica

Upravljačka ploča

Jedinica spremnika

za vodu

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

CONTROL PANEL

• Some functions describe in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR

RESET

FORCE

and

SERVICE

buttons are not in use.

CONTROL PANEL’S DISPLAY

Heat Mode OFF/ON Indicator

Timer/Clock Setting Display

Tank Mode Indicator

Outdoor Ambient Temperature Display

Quiet Mode Indicator

Water Outlet Temperature Display

Backup Heater Enabled/Disabled Indicator

Backup Heater Actual (OFF/ON) Indicator

Force Heater Request OFF/ON Indicator

Booster Heater Actual (OFF/ON) Indicator

External Thermo Controller Connected Display

System Defrost Operation OFF/ON Indicator

Operation LED

System Setting Mode OFF/ON Indicator

Solar Display

System Status Check Mode OFF/ON Indicator

Caution (Tank Temperature above 60°C) Indicator

System Service Mode OFF/ON Indicator

CONTROL PANEL’S BUTTON

OFF/ON Button

Timer Setting Group Buttons

Operation Mode Button

Force Heater Mode Button

Quiet Operation Button

System Service Mode Button

Indoor Unit Backup Heater Enabling Button

System Status Check Button

System Setting Mode Buttons

Error Reset Button

HEAT

TANK

QUIET

FORCE

HEATER

OPERATION

BOOSTER

HEATER

ACTUAL

DEFROST

SETTING

STATUS

SERVICE

WATER OUTLET

OFF

TIMER OUTDOOR

Open cover for buttons selections.

TIMER OUTDOOR

HEAT

SETTING

STATUS

SERVICE

BOOSTER

QUIET

TANK

DEFROST

WATER OUTLET

SET

SELECT

CANCEL

ERROR

RESET

SETTING

STATUS

SERVICEFORCECLOCK

CHECK

OFF

MODE

HEATER

QUIET

OFF/ON

TIMER

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MON TUEWEDTHU FRI SAT SUN

SOLAR REMOTE

2 3 4 5 6

OFF

h i

k l

5 10 3

Notes:

• The current day and time need to be set when:

- The power is turned on for the  rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all

the Timer operations.

1. Press

CLOCK

2. Press

or to set current day.

3. Press

SET

to con rm.

4. Repeat steps 2 and 3 to set the current time.

CONTROL PANEL PREPARATION

Setting Current Day and Time

F568253_YS0212-1.indb 4 10-Feb-12 3:52:01 PM

Pokazatelj uključenosti/isključenosti grijanja

Pokazatelj načina spremnika

Pokazatelj tihog načina rada

Pokazatelj omogućenosti/onemogućenosti pomoćnoga grijača

Pokazatelj uključenosti/isključenosti forsiranoga grijanja

Prikaz priključenosti vanjskog termostata

LED svjetlo koje označava rad uređaja

Solarni prikaz

Pokazatelj upozorenja (Temperatura spremnika iznad 60 °C)

Gumb OFF/ON (isključivanje/uključivanje)

Gumb načina rada

Gumb tihog načina rada

Gumb za grijanje pomoćnoga grijača unutarnje jedinice

Gumbi za sistemske postavke

Gumbi za postavljanje brojača

Gumb forsiranog grijanja

Gumb za uslugu sustava

Gumb za provjeru statusa sustava

Gumb za resetiranje radi pogreške

Prikaz postavki brojača/sata

Prikaz vanjske temperature

Prikaz temperature izlaza za vodu

Pokazatelj stvarne uključenosti/isključenosti

pomoćnoga grijača

Pokazatelj stvarne uključenosti/isključenosti

dodatnoga grijača

Pokazatelj uključenosti/isključenosti radnje

odleđivanja sustava

Pokazatelj uključenosti/isključenosti sistemskih postavki

Pokazatelj uključenosti/isključenosti provjere statusa sustava

Pokazatelj uključenosti/isključenosti usluga sustava

Da biste odabrali gumbe, otvorite

poklopac.

ZASLON UPRAVLJAČKE PLOČE

GUMB UPRAVLJAČKE PLOČE

UPRAVLJAČKA PLOČA

• Neke od funkcija opisanih u ovom priručniku možda se neće moći primijeniti na vaš uređaj.

• Više podataka potražite kod ovlaštenog dobavljača.

• Za običan se rad ne koriste gumbi , i .

Napomene:

• Ispravni datum i vrijeme potrebno je postaviti kada:

– Prvi put uključujete uređaj.

– Nakon što je prošlo dugo vremena od posljednjeg

uključivanja uređaja.

• Vrijeme koje postavite bit će standardno vrijeme za sve

aktivnosti brojača.

PRIPREMA UPRAVLJAČKE PLOČE

Postavljanje trenutnog datuma i vremena

1. Pritisnite .

2. Pritisnite ili da biste postavili trenutačni datum.

3. Pritisnite da biste potvrdili.

4. Ponovite korake 2 i 3 da biste postavili trenutačno

vrijeme.

HRVATSKI

ENGLISH

SETTING UP THE SPECIAL FUNCTIONS

• After initial installation, you can manually adjust the settings. The initial setting remains active until the user changes it.

• The control panel can be used for multiple installations. Some functions may not be applicable to your unit.

• Ensure the operation LED is in OFF condition before setting.

SET

SELECT

CANCEL

SETTING

STATUS

CHECK

1. Press

SET

and

CHECK

simultaneously for 5 seconds to enter special setting mode.

“SETTING” and “STATUS” indicator is ON.

2. Press

or to browse functions.

3. Press

SELECT

to enter function.

4. Press

or to enable YES or disable NO function, or set other options.

5. Press

SET

to con rm.

Set Control Panel’s Display Description

External Thermo Controller (YES / NO)

To set external thermo controller connection.

HEATER

Indoor Backup Heater Capacity Selection (3kW / 6kW / 9kW)

To reduce the heater power whenever unnecessary. Options vary depending on model.

Water System Freeze Prevention Function (YES / NO)

To activate or deactivate water system freeze prevention function when unit is OFF.

TANK

Tank Connection (YES / NO)

To set tank connection.

Note: If select “Tank connection” is “NO”, Set 5 ~ 14 are skipped.

SOLAR

Solar Priority (YES / NO)

To choose the solar use for water tank heat up.

HEAT

Heating Priority (YES / NO)

To choose the room heating as priority during HEAT + TANK mode.

Note: If select “Heating priority” is “YES”, Set 7 ~ 8 are skipped.

HEAT

Heating operation Interval Set

To set timer for Heat mode during HEAT + TANK mode (0.5hour ~ 10 hours).

TANK

Tank Heat-up Interval Set

To set timer for Tank during HEAT + TANK mode (5minutes ~ 1hour 35minutes).

BOOSTER

Booster Heater Function (YES / NO)

To activate or deactivate tank booster heater function.

Note: If select “Booster heater function” is “NO”, Set 10 is skipped.

BOOSTER

Booster Heater Delay Timer Set

To set delay timer for booster heater to ON if water tank temperature is not reached

(20minutes ~ 1hour 35minutes).

• Do not use the system during sterilization to prevent scalding or overheat during shower.

• The sterilization function  eld settings must be con gured by the authorized dealer according to local laws and regulation.

Sterilization (YES / NO)

To set sterilization, if required.

Note: If select “Sterilization” is “NO”, set 12 ~ 14 are skipped.

Sterilization Day & Time Set

To set timer for sterilization (only once a week, will operate even in standby condition).

Sterilization Temperature Set

To set temperature for sterilization function (40°C ~ 75°C).

Sterilization Continue Time

To set timer to maintain heating temperature in order to complete the sterilization

function (5minutes ~ 1hour).

F568253_YS0212-1.indb 5 10-Feb-12 3:52:03 PM

1. U isto vrijeme pritisnite i držite 5 sekundi gumbe i da biste unijeli način

posebnih postavki. Uključen je pokazatelj "SETTING" (postavka) i "STATUS" (status).

2. Pritisnite ili da biste pregledali funkcije.

3. Pritisnite da biste unijeli funkcije.

4. Pritisnite ili da biste omogućili funkciju YES (Da) ili onemogućili funkciju NO (Ne)

ili postavili druge mogućnosti.

5. Pritisnite da biste potvrdili.

Postavljanje

Zaslon upravljačke

ploče

Opis

Vanjski termostat (YES/NO) (da/ne)

Postavljanje vanjske veze s termostatom

2 GRIJAČ

Odabir kapaciteta unutarnjega pomoćnoga grijača (3 kW/6 kW/9 kW)

Za smanjivanje snage grijača kad god on nije potreban. Mogućnosti se razlikuju ovisno o modelu.

Funkcija sprečavanja zaleđivanja vode u sustavu (YES/NO) (Da/Ne)

Za aktiviranje ili deaktiviranje funkcije sprečavanja zaleđivanja vode u sustavu kad je uređaj isključen.

4 SPREMNIK

Veza sa spremnikom (YES / NO) (Da/Ne)

Postavljanje veze sa spremnikom

Napomena: Ako je u "Veza sa spremnikom" odabrano "NO" (Ne), preskaču se postavke 5 ~ 14

5 SOLARNI

Solarni prioritet (YES / NO)

Odabir solarnog načina zagrijavanja vode iz spremnika s vodom.

6 GRIJANJE

Prioritet grijanja (YES / NO)

Za odabir grijanja sobe kao prioriteta u načinu GRIJANJE + SPREMNIK

Napomena: Ako je u "Prioritet grijanje" odabrano "YES" (Da), preskaču se postavke 7 ~ 8

7 GRIJANJE

Postavljanja intervala zagrijavanja

Postavljanje brojača za način grijanja u načinu HEAT + TANK (0,5 sati ~ 10 sati).

8 SPREMNIK

Postavljanja intervala zagrijavanja za spremnik

Postavljanje brojača za spremnik u načinu HEAT + TANK (5 min do 1 sat i 35 min)

9 DODATNI

Funkcija dodatnoga grijača (YES/NO) (Da/Ne)

Za aktiviranje ili deaktiviranje funkcije spremnika dodatnoga grijača.

Napomena: Ako je u "Funkcija dodatnoga grijača" odabrano "No" (Ne), preskače se postavka 10.

10 DODATNI

Postavljanje brojača vremena s odgodom za dodatni grijač

Za postavljanje brojača s odgodom za uključivanje dodatnog grijača (ON) ako se ne

postigne temperatura spremnika za vodu (20 min ~ do 1 sat i 35 min)

Sterilizacija (YES / NO)

Postavljanje sterilizacije, ako je potrebna.

Napomena: Ako je u "Sterilizacija" odabrano "NO" (Ne), preskaču se postavke 12 ~ 14

Postavke vremena i datuma sterilizacije

Za postavljanje brojača vremena za sterilizaciju (samo jednom tjedno, radit će u stanju pripravnosti).

Postavke temperature na kojoj se provodi sterilizacija

Postavljanje temperature za funkciju sterilizacije (40°C ~ 75°C).

Vrijeme trajanja sterilizacije

Postavljanje brojača radi održavanja temperature za grijanje da bi se dovršila funkcija

sterilizacije (5 min ~ 1 sat).

• Nemojte koristiti sustav tijekom sterilizacije. Tako ćete spriječiti isparavanje ili pregrijavanje tijekom tuširanja.

• Postavke polja sterilizacijske funkcije mora kongurirati ovlašteni dobavljač u skladu s lokalnim zakonima i propisima.

POSTAVLJANJE POSEBNIH FUNKCIJA

• Nakon početne instalacije moguće je ručno prilagoditi postavke. Početna postavka ostaje aktivna sve dok je korisnik ne promijeni.

• Upravljačku je ploču moguće koristiti za višestruke instalacije. Neke od funkcija možda se neće moći primijeniti na vaš uređaj.

• Prije postavljanja postavki uvjerite se da LED svjetlo koje označava uključenost/isključenost uređaja ne svijetli.

BASIC OPERATION

OFF

TO TURN ON OR OFF THE UNIT

• When unit is ON, operation LED is lit and the actual

temperature for water outlet and outdoor ambient are

shown on the control panel display.

MODE

TO SELECT OPERATION MODE

HEAT HEAT+TANK TANK

• HEAT MODE

- To turn ON or OFF the panel/ oor heating operation.

- In this mode, the outdoor unit will provide heating

capacity to the indoor unit.

• HEAT + TANK MODE

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank and indoor unit.

- This operation is not used when the sanitary water

tank is not installed.

• TANK MODE

- To turn ON or OFF the sanitary tank operation.

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank.

QUIET

TO ENJOY QUIET ENVIRONMENT

• This operation reduces outdoor unit noise. In this

condition, it may cause decrease in heating capacity.

HEATER

TO ENABLE THE BACKUP

HEATER

• The backup heater provides extra heating capacity

during cold outdoor temperature and only can operated

at heat mode operation for indoor unit when he was

enabled by pushing this button.

• The backup heater will automatically turn ON when the

setting conditions is ful lled.

• To disabled the Heater operation manually, press the

respective button again.

STATUS

CHECK

SYSTEM STATUS CHECK MODE

1. Press

CHECK

for 5 seconds to enter STATUS mode.

2. Press

or to check the Water Inlet

Temperature, Tank Temperature, Compressor Running

Frequency or Error History.

• Press

to exit STATUS mode.

• Once STATUS mode is entered, “STATUS”

indicator is ON.

• STATUS mode cannot be activated when the

“SETTING” indicator is ON.

•

It is strongly recommended to contact the nearest

authorized dealer to change the water temperature range.

• Using the control panel could set the temperature

range for water outlet temperature and outdoor ambient

temperature.

SYSTEM SETTING MODE

SET

SELECT

CANCEL

SETTING

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

HEATER

OPERATION

FORCE

HEATER

ACTUAL

Operation Mode Temperature display

SETTING indicator

Parameter *

1. Press

SET

for 5 seconds to enter “SETTING” mode.

“SETTING” indicator is ON.

2. Press

or to choose a parameter.

3. After selecting the desired parameter, press

SELECT

to enter

the parameter.

4. Press

or to set the desired temperature.

5. Press

SET

again to con rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Operation

Mode

Parameter * Description

HEAT

Low outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

High outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

Water outlet set temperature at low outdoor

ambient temperature (25°C ~ 55°C).

HEAT

Water outlet set temperature at high outdoor

ambient temperature (25°C ~ 55°C).

Water Temperature

Outdoor Temperature

HEAT

OFF

Set temperature for turning OFF heating

operation (5°C ~ 35°C).

HEATER

Outdoor ambient set temperature for turning

ON heater operation (-15°C ~ 20°C).

TANK

Sanitary tank set temperature

(40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

1. Press

SET

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature

(-5°C ~ 5°C).

Notes:

• Press

or wait 30 seconds to exit “SETTING” mode.

• The setting temperature will be stored in the system once

con rm.

• “SETTING” mode cannot be activated when the

“PUMPDW” and “STATUS” indicator is ON.

ADVANCE OPERATION

BASIC OPERATION

OFF

TO TURN ON OR OFF THE UNIT

• When unit is ON, operation LED is lit and the actual

temperature for water outlet and outdoor ambient are

shown on the control panel display.

MODE

TO SELECT OPERATION MODE

HEAT HEAT+TANK TANK

• HEAT MODE

- To turn ON or OFF the panel/ oor heating operation.

- In this mode, the outdoor unit will provide heating

capacity to the indoor unit.

• HEAT + TANK MODE

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank and indoor unit.

- This operation is not used when the sanitary water

tank is not installed.

• TANK MODE

- To turn ON or OFF the sanitary tank operation.

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank.

QUIET

TO ENJOY QUIET ENVIRONMENT

• This operation reduces outdoor unit noise. In this

condition, it may cause decrease in heating capacity.

HEATER

TO ENABLE THE BACKUP

HEATER

• The backup heater provides extra heating capacity

during cold outdoor temperature and only can operated

at heat mode operation for indoor unit when he was

enabled by pushing this button.

• The backup heater will automatically turn ON when the

setting conditions is ful lled.

• To disabled the Heater operation manually, press the

respective button again.

STATUS

CHECK

SYSTEM STATUS CHECK MODE

1. Press

CHECK

for 5 seconds to enter STATUS mode.

2. Press

or to check the Water Inlet

Temperature, Tank Temperature, Compressor Running

Frequency or Error History.

• Press

to exit STATUS mode.

• Once STATUS mode is entered, “STATUS”

indicator is ON.

• STATUS mode cannot be activated when the

“SETTING” indicator is ON.

•

It is strongly recommended to contact the nearest

authorized dealer to change the water temperature range.

• Using the control panel could set the temperature

range for water outlet temperature and outdoor ambient

temperature.

SYSTEM SETTING MODE

SET

SELECT

CANCEL

SETTING

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

HEATER

OPERATION

FORCE

HEATER

ACTUAL

Operation Mode Temperature display

SETTING indicator

Parameter *

1. Press

SET

for 5 seconds to enter “SETTING” mode.

“SETTING” indicator is ON.

2. Press

or to choose a parameter.

3. After selecting the desired parameter, press

SELECT

to enter

the parameter.

4. Press

or to set the desired temperature.

5. Press

SET

again to con rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Operation

Mode

Parameter * Description

HEAT

Low outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

High outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

Water outlet set temperature at low outdoor

ambient temperature (25°C ~ 55°C).

HEAT

Water outlet set temperature at high outdoor

ambient temperature (25°C ~ 55°C).

Water Temperature

Outdoor Temperature

HEAT

OFF

Set temperature for turning OFF heating

operation (5°C ~ 35°C).

HEATER

Outdoor ambient set temperature for turning

ON heater operation (-15°C ~ 20°C).

TANK

Sanitary tank set temperature

(40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

1. Press

SET

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature

(-5°C ~ 5°C).

Notes:

• Press

or wait 30 seconds to exit “SETTING” mode.

• The setting temperature will be stored in the system once

con rm.

• “SETTING” mode cannot be activated when the

“PUMPDW” and “STATUS” indicator is ON.

ADVANCE OPERATION

BASIC OPERATION

OFF

TO TURN ON OR OFF THE UNIT

• When unit is ON, operation LED is lit and the actual

temperature for water outlet and outdoor ambient are

shown on the control panel display.

MODE

TO SELECT OPERATION MODE

HEAT HEAT+TANK TANK

• HEAT MODE

- To turn ON or OFF the panel/ oor heating operation.

- In this mode, the outdoor unit will provide heating

capacity to the indoor unit.

• HEAT + TANK MODE

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank and indoor unit.

- This operation is not used when the sanitary water

tank is not installed.

• TANK MODE

- To turn ON or OFF the sanitary tank operation.

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank.

QUIET

TO ENJOY QUIET ENVIRONMENT

• This operation reduces outdoor unit noise. In this

condition, it may cause decrease in heating capacity.

HEATER

TO ENABLE THE BACKUP

HEATER

• The backup heater provides extra heating capacity

during cold outdoor temperature and only can operated

at heat mode operation for indoor unit when he was

enabled by pushing this button.

• The backup heater will automatically turn ON when the

setting conditions is ful lled.

• To disabled the Heater operation manually, press the

respective button again.

STATUS

CHECK

SYSTEM STATUS CHECK MODE

1. Press

CHECK

for 5 seconds to enter STATUS mode.

2. Press

or to check the Water Inlet

Temperature, Tank Temperature, Compressor Running

Frequency or Error History.

• Press

to exit STATUS mode.

• Once STATUS mode is entered, “STATUS”

indicator is ON.

• STATUS mode cannot be activated when the

“SETTING” indicator is ON.

•

It is strongly recommended to contact the nearest

authorized dealer to change the water temperature range.

• Using the control panel could set the temperature

range for water outlet temperature and outdoor ambient

temperature.

SYSTEM SETTING MODE

SET

SELECT

CANCEL

SETTING

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

HEATER

OPERATION

FORCE

HEATER

ACTUAL

Operation Mode Temperature display

SETTING indicator

Parameter *

1. Press

SET

for 5 seconds to enter “SETTING” mode.

“SETTING” indicator is ON.

2. Press

or to choose a parameter.

3. After selecting the desired parameter, press

SELECT

to enter

the parameter.

4. Press

or to set the desired temperature.

5. Press

SET

again to con rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Operation

Mode

Parameter * Description

HEAT

Low outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

High outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

Water outlet set temperature at low outdoor

ambient temperature (25°C ~ 55°C).

HEAT

Water outlet set temperature at high outdoor

ambient temperature (25°C ~ 55°C).

Water Temperature

Outdoor Temperature

HEAT

OFF

Set temperature for turning OFF heating

operation (5°C ~ 35°C).

HEATER

Outdoor ambient set temperature for turning

ON heater operation (-15°C ~ 20°C).

TANK

Sanitary tank set temperature

(40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

1. Press

SET

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature

(-5°C ~ 5°C).

Notes:

• Press

or wait 30 seconds to exit “SETTING” mode.

• The setting temperature will be stored in the system once

con rm.

• “SETTING” mode cannot be activated when the

“PUMPDW” and “STATUS” indicator is ON.

ADVANCE OPERATION

BASIC OPERATION

OFF

TO TURN ON OR OFF THE UNIT

• When unit is ON, operation LED is lit and the actual

temperature for water outlet and outdoor ambient are

shown on the control panel display.

MODE

TO SELECT OPERATION MODE

HEAT HEAT+TANK TANK

• HEAT MODE

- To turn ON or OFF the panel/ oor heating operation.

- In this mode, the outdoor unit will provide heating

capacity to the indoor unit.

• HEAT + TANK MODE

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank and indoor unit.

- This operation is not used when the sanitary water

tank is not installed.

• TANK MODE

- To turn ON or OFF the sanitary tank operation.

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank.

QUIET

TO ENJOY QUIET ENVIRONMENT

• This operation reduces outdoor unit noise. In this

condition, it may cause decrease in heating capacity.

HEATER

TO ENABLE THE BACKUP

HEATER

• The backup heater provides extra heating capacity

during cold outdoor temperature and only can operated

at heat mode operation for indoor unit when he was

enabled by pushing this button.

• The backup heater will automatically turn ON when the

setting conditions is ful lled.

• To disabled the Heater operation manually, press the

respective button again.

STATUS

CHECK

SYSTEM STATUS CHECK MODE

1. Press

CHECK

for 5 seconds to enter STATUS mode.

2. Press

or to check the Water Inlet

Temperature, Tank Temperature, Compressor Running

Frequency or Error History.

• Press

to exit STATUS mode.

• Once STATUS mode is entered, “STATUS”

indicator is ON.

• STATUS mode cannot be activated when the

“SETTING” indicator is ON.

•

It is strongly recommended to contact the nearest

authorized dealer to change the water temperature range.

• Using the control panel could set the temperature

range for water outlet temperature and outdoor ambient

temperature.

SYSTEM SETTING MODE

SET

SELECT

CANCEL

SETTING

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

HEATER

OPERATION

FORCE

HEATER

ACTUAL

Operation Mode Temperature display

SETTING indicator

Parameter *

1. Press

SET

for 5 seconds to enter “SETTING” mode.

“SETTING” indicator is ON.

2. Press

or to choose a parameter.

3. After selecting the desired parameter, press

SELECT

to enter

the parameter.

4. Press

or to set the desired temperature.

5. Press

SET

again to con rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Operation

Mode

Parameter * Description

HEAT

Low outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

High outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

Water outlet set temperature at low outdoor

ambient temperature (25°C ~ 55°C).

HEAT

Water outlet set temperature at high outdoor

ambient temperature (25°C ~ 55°C).

Water Temperature

Outdoor Temperature

HEAT

OFF

Set temperature for turning OFF heating

operation (5°C ~ 35°C).

HEATER

Outdoor ambient set temperature for turning

ON heater operation (-15°C ~ 20°C).

TANK

Sanitary tank set temperature

(40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

1. Press

SET

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature

(-5°C ~ 5°C).

Notes:

• Press

or wait 30 seconds to exit “SETTING” mode.

• The setting temperature will be stored in the system once

con rm.

• “SETTING” mode cannot be activated when the

“PUMPDW” and “STATUS” indicator is ON.

ADVANCE OPERATION

UKLJUČIVANJE ILI ISKLJUČIVANJE

UREĐAJA

• Kada je uređaj uključen, pali se LED lampica, a stvarna

temperatura izlaza za vodu i vanjska temperatura

prikazuju se na upravljačkoj ploči.

ODABIR NAČINA RADA

•

GRIJANJE

– Paljenje i gašenje grijanja poda/panela.

– U ovom načinu rada vanjska jedinica pruža kapacitet

za grijanje unutarnjoj jedinici.

•

GRIJANJE + SPREMNIK

– U ovom načinu rada vanjska jedinica pruža kapacitet

za grijanje sanitarnom spremniku i unutarnjoj jedinici.

– Radnja se ne koristi kada sanitarni spremnik za vodu

nije instaliran.

•

SPREMNIK

– Paljenje i gašenje rada sanitarnog spremnika.

– U ovom načinu rada vanjska jedinica pruža kapacitet

za grijanje sanitarnom spremniku.

UŽIVANJE U TIHOM OKRUŽENJU

• Ova radnja smanjuje buku koju stvara vanjska jedinica.

U ovom bi stanju mogla dovesti do smanjenja kapaciteta

grijanja.

OMOGUĆAVANJE POMOĆNOGA

GRIJAČA

• Pomoćni grijač pruža dodatni kapacitet za grijanje kod

vrlo niskih vanjskih temperatura i može se koristiti samo

s unutarnjom jedinicom i to u načinu grijanja kad se

pokrene pritiskom na ovaj gumb..

• Pomoćni se grijač uključuje automatski kada se

zadovolje uvjeti okoline.

• Da biste ručno isključili taj grijač, ponovno pritisnite gumb

za pomoćni grijač.

PROVJERA STATUSA SUSTAVA

1. Pritisnite i držite 5 sekundi gumb da biste unijeli

način STATUS.

2. Pritisnite ili da biste provjerili temperaturu

ulaska vode, temperaturu spremnika, frekvenciju pogona

kompresora ili povijest pogrešaka u radu.

• Pritisnite da biste izašli iz načina STATUS.

• Kada uključite način STATUS, pali se lampica

pokazatelja uključenosti za "STATUS".

• Način STATUS nije moguće aktivirati kada je uključen

pokazatelj "SETTING".

OSNOVNE RADNJE NAPREDNI RAD

• Snažno se preporučuje kontaktiranje ovlaštenog

dobavljača da bi se promijenio raspon temperature vode.

• Korištenjem upravljačke ploče moguće je postaviti raspon

temperature za izlaz za vodu i vanjsku okolinu.

NAČIN PODEŠENJA SUSTAVA

1. Pritisnite i držite 5 sekundi gumb da biste unijeli način

"SETTING". Uključen je pokazatelj "SETTING" (postavka).

2. Pritisnite ili da biste odabrali parametar.

3. Nakon što odaberete željeni parametar, pritisnite da

biste unijeli parametar.

4. Pritisnite ili da biste postavili željenu temperaturu.

5. Ponovno pritisnite da biste potvrdili postavku.

• Ponovite korake od 2 do 5 da biste postavili druge parametre.

Način

rada

Parametar * Opis

GRIJANJE

Postavljena niska vanjska temperatura

(-15 °C ~ 15 °C).

GRIJANJE

Postavljena visoka vanjska temperatura

(-15 °C ~ 15 °C).

GRIJANJE

Postavljena temperatura izlaza za vodu pri

niskoj vanjskoj temperaturi (25°C ~ 55°C).

GRIJANJE

Postavljena temperatura izlaza za vodu pri

visokoj vanjskoj temperaturi (25°C ~ 55°C).

GRIJANJE OFF

Postavka temperature za radnu aktivnost

grijanja OFF (5°C ~ 35°C).

GRIJAČ

Postavka vanjske temperature za radnu

aktivnost grijanja ON (-15°C ~ 20°C).

SPREMNIK

Temperatura sanitarnog spremnika (40

°C ~ 75 °C).

POSTAVKE TERMALNOG POMAKA

TEMPERATURE VODE

1. Pritisnite na 5 sekundi.

• Ponovite korake od 3 do 5 da biste postavili željeni

temperaturni pomak (-5°C ~ 5°C).

Napomene:

• Pritisnite ili pričekajte 30 sekundi za izlaz iz načina

"SETTING".

• Temperatura se pohranjuje u sustavu jednom kada je potvrdite.

• Nije moguće aktivirati način "SETTING" kada su uključeni

pokazatelji "PUMPDW" (Crpka ugašena) i "STATUS" (Status).

Način rada

Temperatura vode

Vanjska temperatura

Parametar *

Prikaz temperature

Pokazatelj SETTING (postavke)

HRVATSKI

ENGLISH

TIMER

MON TUEWEDTHU FRI SAT SUN

2 3 4 5 6

OFF

SOLAR REMOTE

Lights up if Timer operation is selected

Day to be selected

ON Timer - To automatically switch “ON” the unit

6 different programs can be set in a day (1 ~ 6)

Indicates the selected day

Water temperature thermo shift (-5ºC ~ 5ºC)

OFF Timer - To automatically switch “OFF” the unit

SET

SELECT

CANCEL

SETTING

CLOCK

OFF/ON

TIMER

STATUS

MODE

HEATER

QUIET

Function Step

Enter timer mode

Press

TIMER

Set day & time

Press or to select your desired day.

Press

SELECT

to con rm.

“1” will be blinking, press

SELECT

to set program 1.

Press

OFF/ON

to select ON or OFF timer.

Press or to select your desired time.

You can set

MODE

QUIET

HEATER

and desired shift temperature with timer.

Press

SET

to con rm program 1. The selected day will be highlighted with ▼.

• After 2 seconds, the display will move to the next program.

Repeat steps 4 to 7 to set programs 2 to 6.

• During timer setup, if no button is pressed within 30 seconds, or if the

SET

button is pressed the

setting at that moment is con rmed and timer setup is ended.

Add/Modify timer

Repeat the steps above.

Disable timer

Press

TIMER

, then press

CANCEL

Enable timer

Press

TIMER

, then press

SET

Check timer

1. Press

TIMER

2. Press or until your desired day is shown, press

SELECT

to con rm your selection.

3. Press or to check the set programs.

Cancel timer

1. Press

TIMER

2. Press or until your desired day is shown, press

SELECT

to con rm your selection.

3. Press

SELECT

to enter program setting.

4. Press or until your desired program is shown.

5. Press

CANCEL

to cancel the program.

WEEKLY TIMER SETTING

Notes:

• You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.

• When the unit is switched on by the ON TIMER, it will use the previously set temperature to control the water outlet

temperature.

• Same timer program cannot be set in the same day.

• You may also select collective days with same timer setting.

• Promotes energy saving by allowing you to set up to 6 programs in any given day.

F568253_YS0212-1.indb 7 10-Feb-12 3:52:06 PM

Funkcija Korak

Unesite način brojača Pritisnite .

Postavljanje datuma

i vremena

1. Pritisnite ili za odabir željenog datuma.

2. Pritisnite da biste potvrdili.

3. Svijetli "1", pritisnite da biste postavili program 1.

4. Pritisnite da biste odabrali brojač ON ili OFF.

5. Pritisnite ili da biste odabrali željeno vrijeme.

Brojačem možete postaviti , , i željeni pomak temperature .

6. Pritisnite da biste potvrdili program 1. Odabrani dan bit će označen s ▼.

• Nakon što prođu dvije sekunde, prikaz će preći na sljedeći program.

7. Ponovite korake od 4 do 7 da biste postavili programe od 2 do 6.

• Ako ne pritisnete niti jedan gumb 30 sekundi ili ako pritisnete gumb tijekom podešavanja

brojača, potvrđuje se postavka odabrana u tom trenutku i postavka brojača je završena.

Dodavanje/izmjena

brojača

Ponovite prethodne korake.

Onemogući brojač Pritisnite , a zatim pritisnite .

Omogući brojač Pritisnite , a zatim pritisnite .

Provjera brojača

1. Pritisnite .

2. Pritišćite ili dok se ne prikaže željeni datum, pritisnite da biste potvrdili odabir.

3. Pritisnite ili da biste provjerili postavljene programe.

Poništavanje

brojača

1. Pritisnite .

2. Pritišćite ili dok se ne prikaže željeni dan, pritisnite da biste potvrdili odabir.

3. Pritisnite da biste unijeli programsku postavku

4. Pritišćite ili dok se ne prikaže željeni program.

5. Pritisnite da biste poništili program.

Napomene:

• Moguće je podesiti brojač za svaki dan u tjednu (od ponedjeljka do nedjelje] sa 6 programa po danu.

• Kada uređaj uključite pomoću gumba BROJAČ ON, koristit će prethodno postavljenu temperaturu za kontroliranje

temperature izlaza za vodu.

• Isti program brojača nije moguće postaviti za isti dan.

• Možete i odabrati zbroj dana s istom postavkom brojača.

• Omogućuje uštedu energije tako što omogućuje postavke do 6 programa u svakom danu.

POSTAVKE TJEDNOG BROJAČA

Pokazuje odabrani dan

Zasvijetli kada odaberete funkciju Timer (brojač)

Za jedan je dan moguće postaviti 6 različitih programa (1 ~ 6)

Termalni pomak temperature vode (-5°C ~ 5°C)

Brojač OFF – Automatsko isključivanje uređaja

Brojač ON – Automatsko uključivanje uređaja

Odabir dana

HEATER

0.2

0.40

0.30.1

MPa

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

OFF

HEATER

OPERATION

FORCE

HEATER

ACTUAL

TIMER

MONTUEWEDTHUFRISAT SUN

SOLAR REMOTE

NOT AVAILABLE

2 3 4 5 6

OFF

INDOOR UNIT

CAUTION

• Switch off the power supply before cleaning.

WATER PRESSURE GAUGE

0.2

0.40

0.30.1

MPa

• Do not press or hit the glass

cover with hard, pointed

objects. This may damage the

unit.

• Ensure that the water

pressure is between 0.05 to

0.2 MPa (0.1 MPa = 1 bar).

• In case the water pressure is

out of the above range, please

consult authorized dealer.

CLEANING INSTRUCTIONS HINT

• Do not use benzene, thinner or scouring powder.

• Use only soap (

pH7) or neutral household detergent.

• Do not use water hotter than 40°C.

• To ensure optimal performance of the unit, cleaning

maintenance has to be carried out at regular intervals.

Please consult authorized dealer.

INDOOR UNIT & CONTROL PANEL

• Do not splash water directly.

• Wipe the unit gently with a soft, dry cloth.

EXTERNAL FILTER

• Please clean the external  lter at least once a year. Fail to do so might cause  lter clogged, consequent system

breakdown. Please consult authorized dealer.

OUTDOOR UNIT

• Do not obstruct the air inlet and air outlet vents, it may cause low performance or breakdown. Please remove obstacles to

assure the ventilation.

• During winter, please clean and remove the snow near outdoor unit so that the snow does not cover the air inlet and air

outlet vents.

INSPECTION

• In order to ensure optimal performance of the unit, seasonal inspections on the unit, external  lter and  eld wiring have to

be carried out at regular intervals. This maintenance should be carried out by authorized dealer.

• Clear any obstruction at the air inlet and air outlet vents of outdoor unit.

FOR EXTENDED NON-USE

• Turn off the power supply.

NON SERVICEABLE CRITERIAS

TURN OFF POWER SUPPLY then please consult authorized dealer under the following conditions:

• Abnormal noise during operation.

• Water/foreign particles have entered the control panel.

• Water leaks from Indoor unit.

• Circuit breaker switches off frequently.

• Power cord becomes unnaturally warm.

UNUTARNJA JEDINICA

• Nemojte prskati vodu direktno na uređaj.

• Uređaj nježno obrišite mekom suhom krpom.

• Isključite napajanje.

• Očistite vanjski ltar barem jednom godišnje. Ako to ne učinite, ltar bi se mogao začepiti, što bi za posljedicu moglo imati

kvar sustava. Posavjetujte se s ovlaštenim dobavljačem.

• Nemojte blokirati dovode zraka i izlazne ventile za zrak jer može doći do smanjenih performansi ili kvara. Uklonite

predmete koji blokiraju da biste omogućili ispravnu ventilaciju.

• Zimi čistite i uklanjajte snijeg oko vanjske jedinice kako ne bi prekrio dovod zraka i izlazne ventile za zrak.

• Da bi se osigurale optimalne performanse uređaja, nužno je provoditi sezonski pregled uređaja, pregled vanjskih ltara i

kabela u redovnim intervalima. Takvo održavanje treba provoditi ovlašteni dobavljač.

• Očistite prepreke na otvorima dovoda zraka i ventilima odvoda zraka na vanjskoj jedinici.

U sljedećim slučajevima ISKLJUČITE NAPAJANJE i obratite se ovlaštenom dobavljaču:

• Neuobičajena buka tijekom rada.

• U upravljačku ploču ušla je voda ili strane čestice.

• Iz unutarnje jedinice curi voda.

• Strujni se prekidač često isključuje.

• Kabel se neobično zagrijava.

UNUTARNJA JEDINICA I UPRAVLJAČKA PLOČA

DULJE RAZDOBLJE NEKORIŠTENJA

VANJSKI FILTAR

VANJSKA JEDINICA

PREGLED

KRITERIJI KOJI SE NE MOGU POPRAVITI

• Prije čišćenja isključite napajanje.

MJERAČ ZA PRITISAK VODE

• Nemojte pritiskati ili lupati po

staklenom poklopcu tvrdim,

zašiljenim predmetima. Tako

može doći do oštećenja uređaja.

• Provjerite je li pritisak vode

između 0,05 i 0,2 MPa (0,1

MPa = 1 bar].

• Ako je vodni pritisak iznad gore

navedenog raspona, obratite

se ovlaštenom dobavljaču.

UPUTE ZA ČIŠĆENJE

• Ne upotrebljavajte benzen, razrjeđivač ili abrazivna sredstva.

• Upotrebljavajte samo sapun (~

pH7) ili neutralni

deterdžent za kućanstvo.

• Ne upotrebljavajte vodu temperature iznad 40°C.

SAVJET

• Da bi se osigurao optimalan rad uređaja, nužno je

čistiti uređaj u pravilnim vremenskim razmacima.

Posavjetujte se s ovlaštenim dobavljačem.

HRVATSKI

Sljedeće situacije nisu naznaka kvara.

Gumb forsiranog grijanja

• Isključite uređaj i dojavite ovlaštenom dobavljaču kod pogreške.

• Rad brojača poništava se kada se pojavi šifra greške.

U SLUČAJU PROBLEMA

SIMPTOM UZROK

Tijekom rada čuje se zvuk protjecanja vode. ► • Protok rashladnog sredstva u uređaju.

Rad počinje nekoliko minuta nakon ponovnog pokretanja

uređaja.

► • Odgoda znači zaštitu kompresora uređaja.

Iz vanjske jedinice izlaze voda/para. ► • Na cijevima se javlja kondenzacija ili isparavanje.

Vanjska jedinica ispušta paru tijekom grijanja. ► • To je zbog radnji odmrzavanja u izmjenjivaču topline.

Vanjska jedinica ne radi. ► • Kada je vanjska temperatura van operativnog raspona,

sustav toplinske crpke unosi zaštitnu kontrolu.

Gasi se sustav toplinske crpke zrak-voda. ► • Ako je temperatura dovoda za vodu unutarnje

jedinice niža od 20 °C. Uključuje se pomoćni grijač

koji zagrijava vodu.

Sustav se teško zagrijava. ► • Kada se grije unutarnjom jedinicom, a istovremeno

je uključeno i grijanje poda ili panela, moglo bi biti

situacija u kojima je temperatura vode sve niža i

zagrijavanje poda i grijač panela sve slabiji.

• Kada je vanjska temperatura zraka niska, možda će

se teže zagrijati.

• Blokira li hrpa snijega odvod za ispust ili dovod

vanjske jedinice?

• Kada je postavljena temperatura izlaza za vodu

niska, možda će se teže zagrijati.

Sustav se ne može trenutno zagrijati. ► • S obzirom na prirodu sustava toplinske crpke, moglo

bi biti potrebno određeno vrijeme da se voda zagrije

ako se uređaj pokreće na hladno paljenje.

Pomoćni se grijač automatski uključuje kada nije omogućen. ► • Uključivanje pomoćnoga grijača štiti izmjenjivač

topline unutarnje jedinice.

Ponovni početak rada nakon što se struja vrati. ► • Uređaj radi pod funkcijom automatskog ponovnog

pokretanja.

Prije poziva serviseru provjerite sljedeće.

SIMPTOM PROVJERA

Grijanje ne radi učinkovito. ► • Ispravno postavite temperaturu.

• Je li ventil za grijanje na panelu zatvoren?

• Očistite prepreke na otvorima dovoda zraka i

ventilima odvoda zraka na vanjskoj jedinici.

Bučan rad. ► • Provjerite je li uređaj instaliran na neravnoj površini i

je li poklopac ispravno zatvoren.

Uređaj ne radi. ► • Provjerite je li prekidač oštećen.

LED svjetlo koje označava je li uređaj uključen ne gori ili je

zaslon upravljačke ploče prazan.

► • Napajanje je isključeno ili je došlo do nestanka struje.

ENGLISH

TROUBLESHOOTING

The following symptoms do not indicate malfunction.

SYMPTOM CAUSE

Flowing sound during operation. ► • Refrigerant  ow inside the unit.

Operation is delayed a few minutes after restart. ► • The delay is a protection to the unit’s compressor.

Outdoor unit emits water/steam. ► • Condensation or evaporation occurs on pipes.

Outdoor unit emits steam during heating mode. ► • This is due to defrost operation happens at the heat

exchanger.

Outdoor unit does not operate. ► • When the outdoor temperature is out of the operation

condition range, the heatpump system enter protection

control.

Air-to-Water Heatpump system operation will turn off. ► • If indoor unit water inlet temperature is lower than 20°C.

Backup heater power will turn on to heat up the water.

System dif cult to heat-up. ► • When heating is operated by indoor unit together with

 oor heating or panel heater simultaneously, there

may be case where warm water temperature is getting

lower and cause  oor heating or panel heater heat-up is

weaken.

• When outdoor air temperature is low, it may be dif cult to

get warm.

• Is the snow pile blocking the discharge outlet or intake

inlet of outdoor unit.

• When water outlet set temperature is low, it may be

dif cult to get warm.

System cannot get warm instantly. ► • Due to the nature of the heatpump system, it may take

some time to heat-up the water if the unit is operated

from cold-start.

Operation starts after power resumes. ► • Unit is operates under auto restart function.

Check the following before calling for servicing.

SYMPTOM CHECK

Heating operation is not working ef ciently. ► • Set the temperature correctly.

• Is the panel heater valve closed.

• Clear any obstruction at the air inlet and air outlet vents

of outdoor unit.

Noisy during operation. ► • Check if the unit has been installed at an incline or the

cover is not closed properly.

The unit does not work. ► • Check if the circuit breaker is tripped.

Operation LED is no lit or control panel display

is blank.

► • Is the power supply off or power failure.

The operation LED blinks and error code appear on control panel display.

TIMER

MON TUEWEDTHU FRI SAT SUN

2 3 4 5 6

OFF

• Turn the unit off and reveal the error code to authorized dealer.

• Timer operation cancel when error code occur.

Force Heater Mode Button

FORCE

• In case of a failure of the Air-to-Water Heatpump system, the backup heater can be used to heat

up the heating water. Press

FORCE

to switch on the backup heater.

• Press

OFF

to stop the force heater operation.

• During Force Heater mode, all other operations are not allowed.

LED svjetlo koje označava je li uređaj uključen treperi i šifra greške prikazuje se na zaslonu upravljačke ploče.

• U slučaju kvara toplinske crpke zrak-voda moguće je korisititi pomoćni grijač za zagrijavanje

vode. Pritisnite za prebacivanje na pomoćni grijač.

• Pritisnite kako biste zaustavili rad forsiranog grijanja.

• U načinu forsirano grijanje sve druge radnje nisu dozvoljene.

Informacije za korisnike o prikupljanju i zbrinjavanju dotrajale opreme

Ove oznake na proizvodu, ambalaži i/ili pratećim dokumentima označavaju da se korišteni električni i

elektronički uređaji ne smiju zbrinjavati zajedno s otpadom iz domaćinstava.

Radi pravilne obrade, sanacije i recikliranja dotrajalih proizvoda, molimo vas da ih odnesete u odgovarajuća

odlagališta, u skladu s lokalnim zakonodavstvom i Direktivama 2002/96/EZ i 2006/66/EZ. Pravilnim

zbrinjavanjem navedenih proizvoda čuvate vrijedne resurse i sprečavate moguće negativne učinke po

ljudsko zdravlje koji mogu nastati zbog nepravilnog rukovanja otpadom. Detaljne informacije o prikupljanju i

recikliranju dotrajalih proizvoda zatražite od svojeg lokalnog poglavarstva, službe za zbrinjavanje otpada ili

prodavatelja kod kojeg ste kupili proizvode. Nepravilno zbrinjavanje ovog otpada može imati za posljedicu

prekršajnu odgovornost u skladu s nacionalnim zakonodavstvom.

Za poslovne korisnike u Europskoj uniji

Ako želite odložiti električnu i elektroničku opremu, detaljne obavijesti zatražite od svojeg prodavača ili

dobavljača.

[Informacije o odlaganju u zemljama izvan Europske unije]

Ovi su simboli važeći samo u Europskoj uniji. Ako želite odložiti ove uređaje, obratite se nadležnim lokalnim

tijelima ili dobavljačima i raspitajte se o pravilnoj metodi odlaganja.

INFORMACIJE

Information for Users on Collection and Disposal of Old Equipment

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your

waste disposal service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

INFORMATION/INFORMATIONS/INFORMACIÓN/

INFORMATIONEN/INFORMAZIONI/ INFORMATIE/

INFORMAÇÃO/ΠΛΗΡΟΦΟΡΙΕΣ/ИНФОРМАЦИЯ

Avis aux utilisateurs concernant la collecte et l’élimination des piles et des appareils usagés

Apposé sur le produit lui-même, sur son emballage, ou  gurant dans la documentation qui l’accompagne, ce

pictogramme indique que les piles et appareils électriques et électroniques usagés doivent être séparés des ordures

ménagères.

A n de permettre le traitement, la valorisation et le recyclage adéquats des piles et des appareils usagés, veuillez les

porter à l’un des points de collecte prévus, conformément à la législation nationale en vigueur ainsi qu’aux directives

2002/96/CE et 2006/66/CE.

En éliminant piles et appareils usagés conformément à la réglementation en vigueur, vous contribuez à prévenir

le gaspillage de ressources précieuses ainsi qu’à protéger la santé humaine et l’environnement contre les effets

potentiellement nocifs d’une manipulation inappropriée des déchets.

Pour de plus amples renseignements sur la collecte et le recyclage des piles et appareils usagés, veuillez vous

renseigner auprès de votre mairie, du service municipal d’enlèvement des déchets ou du point de vente où vous avez

acheté les articles concernés.

Le non-respect de la réglementation relative à l’élimination des déchets est passible d’une peine d’amende.

Pour les utilisateurs professionnels au sein de l’Union européenne

Si vous souhaitez vous défaire de pièces d’équipement électrique ou électronique, veuillez vous renseigner directement

auprès de votre détaillant ou de votre fournisseur.

[Information relative à l’élimination des déchets dans les pays extérieurs à l’Union européenne]

Ce pictogramme n’est valide qu’à l’intérieur de l’Union européenne. Pour connaître la procédure applicable dans les pays

hors Union Européenne, veuillez vous renseigner auprès des autorités locales compétentes ou de votre distributeur.

Información para usuarios sobre la recogida y eliminación de aparatos viejos

Estos símbolos en los productos, embalajes y/o documentos adjuntos, signi can que los aparatos eléctricos

y electrónicos y las baterías no deberían ser mezclados con los desechos domésticos.

Para el tratamiento apropiado, la recuperación y el reciclado de aparatos viejos y baterías usadas, por favor,

observe las normas de recogida aplicables, de acuerdo a su legislación nacional y a las Directivas 2002/96/

CE y 2006/66/CE.

Al desechar estos aparatos y baterías correctamente, Usted estará ayudando a preservar recursos valiosos y

a prevenir cualquier potencial efecto negativo sobre la salud de la humanidad y el medio ambiente que, de lo

contrario, podría surgir de un manejo inapropiado de los residuos.

Para mayor información sobre la recolección y el reciclado de aparatos y baterías viejas, por favor, contacte

con su comunidad local, su servicio de eliminación de residuos o al comercio donde adquirió estos aparatos.

Podrán aplicarse penas por la eliminación incorrecta de estos residuos, de acuerdo a la legislación nacional.

Para usuarios empresariales en la Unión Europea

Si usted desea desechar aparatos eléctricos y electrónicos, por favor contacte con su distribuidor o proveedor

a  n de obtener mayor información.

[Informacion sobre la Eliminación en otros Países fuera de la Unión Europea]

Estos símbolos sólo son válidos dentro de la Unión Europea. Si desea desechar estos objetos, por favor

contacte con sus autoridades locales o distribuidor y consulte por el método correcto de eliminación.

Ovlašteni predstavnik u EU-u

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Njemačka

F568675

YS0212-0

Panasonic Corporation

Web-mjesto: http://panasonic.hr

Panasonic WHUH12DE8 Operating instructions

Brand: Panasonic

Model: WHUH12DE8

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Panasonic WHUH12DE8 Operating instructions

This manual is also suitable for

Panasonic WHUH12DE8 Operating instructions

Related papers

Other documents