8
Board Layout and Jumper Settings
934-DT1220-8A0G
A38801533
www.dfi .com
Clear CMOS Data
JP1
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
Digital I/O Power Select JP12
+5V_standby (default) 1-2 On
+5V 2-3 On
Auto Power-on Select JP15
Power-on via power button (default) 1-2 On
Power-on via AC power 2-3 On
Digital I/O Output State:
DIO 0-3 (JP13), DIO 4-7 (JP14)
+5V or +5V_standby (default) 1-2 On
GND 2-3 On
Note:
1. SATA 0 supports SATA DOM.
2. When COM 1 RS232/422/485 is selected, JP4 and JP5 must
be set in accordance to JP3.
(JP14)
(JP12)
(JP13)
USB 3.0 0-1 Power
Select (JP8)
USB 3.0 2-3 Power
Select (JP9)
(JP15)
2
1
10
9
2
1
10
9
Mini PCIe
LAN 1
USB 0-1
USB 3.0
LAN 2
USB 2-3
USB 3.0
USB 2.0
1
Digital
I/O
1224
ATX Power
1
13
USB 5
USB 2.0
Auto Power-on
Select (JP15)
DIO Power Select (JP12)
DIO 0-3 Output State (JP13)
DIO 4-7 Output State (JP14)
DP 0-1
DP 2-3
Mic-in
Line-in
Line-out
1
1
1
1
210
9
COM 4
1
210
9
COM 1
1
210
9
COM 3
1
210
9
COM 2
1
12
2
11
LPC
1
S/PDIF
1
109
2
Front
Audio
1
System Fan
1
CPU Fan
USB 2-3 USB 0-1
SPI Flash
BIOS
DDR3_2 SODIMM
DDR3_1 SODIMM
Standby
Power LED
1
1
SATA 1
11
SATA 2SATA 3
1
SATA 0
Battery
12
11 12
Front
Panel
1
1
1
SMBus
1
2
5
6
(JP3)
65
21
65
21
65
21
(JP5)
(JP4)
12 10
3
1
1
1
1
1
PCIe x16
Buzzer
14
AMD
AMD
R-Series
A77E
Clear CMOS
Data (JP1)
SATA DOM Power
Select (JP2)
(JP5)
(JP3)
COM 1
RS232/422/485
Select
(JP4)
Mini PCIe Signal
Select (JP6)
Mini PCIe Power
Select (JP7)
USB 2.0 0-1/2-3
Power Select (JP10)
USB 2.0 5 Power
Select (JP11)
Realtek
ALC888
Intel
WGI210AT
Chassis
Intrusion
1
SATA 3.0
Note:
SATA 0 supports SATA DOM.
Digital I/O
Power
SATA DOM Power Select JP2
GND (default) 1-2 On
+5V 2-3 On
COM 1 RS232/422/485 Select JP3
RS232 (default) 1-2 On
RS422 Full Duplex 3-4 On
RS485 5-6 On
COM 1 RS232/422/485 Select JP4/JP5
RS232 (default) 1-3, 2-4 On
RS422 Full Duplex/RS485 3-5, 4-6 On
Mini PCIe Signal Select JP6
PCIe (default)
1-4-7-10
2-5-8-11 On
mSATA
2-5-8-11
3-6-9-12 On
Mini PCIe Power Select JP7
+3.3V_standby (Mini PCIe) (default) 1-2 On
+3.3V (mSATA) 2-3 On
USB Power Select: 3.0 0-1 (JP8), 3.0 2-3 (JP9)
2.0 0-1/2-3 (JP10), 2.0 5 (JP11)
+5V (default) 1-2 On
+5V_standby 2-3 On