English User Manual
READ ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new
Lezyne GPS device.
Important
DO NOT BECOME DISTRACTED by the device—always operate vehicles in a safe manner.
Lezyne USA, Inc. does not accept any liability for injuries or other damages resulng from
the use of this product in any circumstances.
Lezyne GPS devices have a water resistance rang of IPX7 under IEC standard 60529.
Submerging the device is not recommended. If moisture does enter the casing, air out
unl completely dry.
DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.
DO NOT OPERATE OR STORE OUSIDE OF TEMPERATURE RANGE (-20–70° C). Baery life
may be aected at temperature extremes.
Locaon and surroundings may aect GPS signal. For best results, use the device
outdoors with an unobstructed view of the sky. It may take up to 120 seconds to acquire
GPS signals.
This GPS device is not a calibrated measuring tool. It should not be used for surveying
purposes. GPS based elevaon measurements may vary. Calorie readings are an esma-
on for reference only.
CA PROPOSITION 65 WARNING: This product may contain chemicals known to the State
of California to cause cancer and birth defects or other reproducve harm (California law
requires this warning to be given to customers in the State of California). For more info:
www.lezyne.com/prop65
Warranty
In U.S. and U.K., Lezyne GPS devices carry a two (2) year warranty from the original
purchase date to the original owner (proof of purchase required). Lezyne Baeries
carry a six (6) month warranty from the original purchase date. Lezyne warranes
cover any manufacturing defects in materials or workmanship. Issues not covered by
warranty include normal wear & tear, improper installaon, aempng to access or
modify electronics, damage or failure due to accident, misuse, abuse and/or neglect.
For all warranty issues worldwide, please contact the retailer that sold the product.
For any warranty quesons contact: warranty@lezyne.com
Mounting
To aach the bike mount:
1. Align the shim with the boom of the mount.
2. Aach the mount securely using the two bands.
To connect the device to the bike mount:
1. Align the tabs on the back of the device with the mount.
2. Press down and turn the device unl it locks into place.
Charging
Before using your Lezyne GPS device for the rst me, fully
charge baery. To charge your device:
1. Remove exterior moisture
2. Open USB cover
3. Connect micro USB cable and device to powered USB
port. For best results, use the supplied Lezyne cable.
If device does not display charging symbol when plugged in,
selected USB port may not be powered—try another USB port.
Correct USB Seal Installation
When charging is complete, ensure USB seal is correctly installed for water resistance:
1. Install one side at a me
2. Visually inspect for correct installaon
Menu & Pause Screen Button Functions
Click
Select
Up
Down
Ride screen button functions
Click
Hold
Light
ON/OFF
Page/Scroll
Menu
Start/Lap
Pause
Operation
Starng a ride:
1. Hold the le buon to turn the Mini GPS ON
2. Wait for GPS to connect
3. Click the boom right buon to start recording
Stopping a ride:
1. Hold the boom right buon to PAUSE
2. Click the right buons to scroll through the opons
3. Click the le buon to select END
4. Click the le buon again to select SAVE
Navigang a menu:
1. Click the right buons to scroll through the opons
2. Click the le buon to select
More Information
For more informaon on Lezyne products, visit: hp://lezyne.com
WEEE Noce & Product Disposal:
The symbol of the crossed waste container means that, in accordance with2002/96/EC
Waste Electrical and Electronic Equipment Direcve (WEEE),once the product reaches
the end of its lifecycle, in the European Union it is subject to special waste disposal. In
addion to the present device, this rule is also applied to all items carrying such a symbol.
Do not dispose of these products as undierenated urban waste but put away for mate-
rial dierenated recycling.
CE RF Compliance—Meets the EU Requirements:
The equipment complies with the RF Exposure Requirement 1999/519/EC, Council
Recommendaon of 12 July 1999 on the limitaon of exposure of the general public to
electromagnec elds (0–300 GHz). Changes or modicaons to this product not autho-
rized by the manufacturer could void the EMC compliance and negate your authority to
operate the product. This product has demonstrated EMC compliance under condions
that included the use of compliant peripheral devices and shielded cables between sys-
tem components. It is important that you use compliant peripheral devices and shielded
cables between system components to reduce the possibility of causing interference to
radios, televisions, and other electronic devices. We, hereby, declare that this cellular,
Wi-Fi radio is in compliance with the essenal requirements and other relevant provi-
sions of Direcve 1999/5/EC. Products with CE marking comply with the EMC Direcve
(2004/108/EC) and the Low Voltage Direcve (2006/95/EC) issued by the Commission of
the European Community. Compliance with these direcves implies conformity to the
following European Norms (in parentheses are the equivalent internaonal standards).
FCC & IC User Warning Noce:
Any changes or modicaons not expressly approved by the party responsible for com-
pliance could void your authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protecon against harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference to radio communica-
ons. However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or television
recepon, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Labelling Requirement Noce:
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt
RSS standard(s). Operaon is subject to the following two condions: (1) this device
may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operaon of the device.
FCC:
1. This Transmier must not be co-located or operang in conjuncon with any
other antenna or transmier.
2. This equipment complies with FCC RF radiaon exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cenmeters between the radiator
IC:
This device complies with the Canada portable RF exposure limit set forth for an uncon-
trolled environment and are safe for intended operaon as described in this manual.
The further RF exposure reducon can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such funcon is
available.
/