Craftsman 315228110 User manual

Brand: Craftsman

Model: 315228110

Category: Power tools

Type: User manual

This manual is also suitable for

315.22811

Owner's Manual

10 in.

TABLE SAW

Model No.

315.228110

Save this manual for

future reference.

_, CAUTION: Read and follow all

Safety Rules and Operating

Instructions before first use of this

product.

Customer Help Line: 1-800-932-3188

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

visit the Craftsman web page: www.sears.com/craftsman

972000-713

1-00

• Safety

• Features

• Assembly

• Operation

• Maintenance

• Parts List

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW

If this rRRFTSMRN Table Saw fails due to a defect in material or workmanship within one year from the date of

purchase, Sears will repair it, free of charge

Contact a Sears Service Center for repair.

If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of

purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoftman Estates, IL 60179

Your saw has many features for making cutting operations more pleasant and enjoyable. Safety, performance

and dependability have been given top priority in the design of this saw making it easy to maintain and operate.

CAUTION: Carefully read through this entire owner's manual before using your new saw. Pay close

attention to the Rules For Safe Operation, and all Safety Alert Symbols, including Danger, Warning and

Caution. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable

service.

_. Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

,_ WARNING:

The operation of any powertool can resultin foreign objects being thrown into your eyes,

which can result in severe eye damage, Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face shield when needed.

We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety

giasses with side shields, available at Sears Retail Stores.

• Warranty and Introduction .......................................................................................................................... 2

• Table Of Contents ..................................................................................................................................... 2-3

• Rules For Safe Operation ......................................................................................................................... 4-6

• Electrical ........................................................................................................................................................ 7

• Glossary and Product Specifications ........................................................................................................ 8

• Unpacking and Accessories ....................................................................................................................... 9

• Loose Parts List .................................................................................................................................... 10-11

• Tools Needed .............................................................................................................................................. 12

• Features .................................................................................................................................................. 13-15

• Assembly ................................................................................................................................................ 16-20

A. Assembly Of Leg Stand, Storage Brackets, and Mounting To Saw .................................................. 16-17

Assembling Leg Stand ............................................................................................................................ 16

Assembling Storage Brackets ................................................................................................................. 17

Mounting The Leg Stand On The Table Saw Base ................................................................................ 17

B. Assembly Of Rails, Tables, and Fences ............................................................................................ 18-19

To Install Front and Back Rail ................................................................................................................. 18

To Install Miter Table and Fence ............................................................................................................. 18

To Install Accessory Table and Rip Fence ............................................................................................. 19

(RRFTSMRN" TABLESAW315.228110 2

C.BladeCheckandBladeGuardAssembly..........................................................................................19-20

To Check Saw Blade Installation ............................................................................................................ 19

To Install Blade Guard ............................................................................................................................. 20

• Operation ................................................................................................................................................ 21-33

A. General Information ................................................................................................................................. 21

Grounding ................................................................................................................................................ 2t

Types Of Cuts ..................................................................................................................................... 21-22

Cutting Tips ............................................................................................................................................. 22

B. Settings and Adjustments ................................................................................................................... 23-28

To Remove The Blade ............................................................................................................................ 23

To Check Replace Or Adjust The Riving Knife and Blade Guard Assembly .......................................... 24

1. Remove The Throat Plate ............................................................................................................... 24

To Reduce The Risk Of Kickback ........................................................................................................... 25

To Avoid Kickback ................................................................................................................................... 25

To Make A Push Stick ............................................................................................................................. 26

Featherboard ........................................................................................................................................... 26

How To Make A Featherboard ................................................................................................................ 26

How To Mount A Featherboard ............................................................................................................... 26

To Adjust Blade Depth ............................................................................................................................ 27

To Adjust Blade Angle ............................................................................................................................. 27

To Set The Scale To The Blade .............................................................................................................. 27

To Lock Miter Table ................................................................................................................................. 28

C. Making Cuts ........................................................................................................................................ 28-33

To Make A Straight Cross Cut ............................................................................................................ 28-29

To Make A Miter Cut ............................................................................................................................... 29

To Make A Straight Rip Cut ..................................................................................................................... 29

To Make A Bevel Cross Cut .................................................................................................................... 30

To Make A Bevel Rip Cut ................................................................................................................... 30-31

To Make A Compound Miter Cut ............................................................................................................. 31

To Make A Large Panel Cut .................................................................................................................... 31

To Make Non-Through Cuts .................................................................................................................... 32

To Make Dado Cuts ................................................................................................................................ 33

• Maintenance ......................................................................................................................................... .. 34-36

A. General Maintenance .............................................................................................................................. 34

B. Specific Table Saw Maintenance ....................................................................................................... 34-36

To Set Blade At 0 Or 45 Degrees ........................................................................................................... 34

To Check The Alignment Of The Rip Fence To The Blade .................................................................... 35

To Adjust The Bevel Locking Lever ........................................................................................................ 35

To Align The Miter Locking Clamps ........................................................................................................ 36

To Adjust The Front and Rear Rail Clamps ............................................................................................ 36

To Adjust The Accessory Table .............................................................................................................. 36

• Sliding Miter Table Assembly .............................................................................................................. 37-41

Checking Sliding Miter Table Assembly ....................................................................................................... 38

To Check Miter Base Parallelism ............................................................................................................ 38

To Check Miter Fence Alignment ............................................................................................................ 39

Making Adjustments To Sliding Miter Table Assembly ........................................................................... 39-41

To Adjust The Miter Base ........................................................................................................................ 39

To Adjust The Miter Fence ...................................................................................................................... 40

To Adjust Quick Stop ............................................................................................................................... 41

• Lubrication .................................................................................................................................................. 42

Locker Bracket Assembly ............................................................................................................................. 42

Tilt / Elevating Mechanism ........................................................................................................................... 42

• Troubleshooting .................................................................................................................................... 44-45

• Exploded View and Repair Parts List .................................................................................................. 46-53

• Parts Ordering / Service ............................................................................................................... back page

3 CRAFTSMAN"TABLESAW315.228110

The purpose of safety symbols isto attract your attention to possible dangers. The safety symbols, and the

explanations with them, deserve your careful atten'iion and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident

prevention measures.

SYMBOL

Note:

MEANING

SAFETY ALERT SYMBOL

Indicatesdanger, warning, or caution,May be used in conjunctionwith othersymbolsor

pictographs.

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to

yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock

and personal injury.

Advises you of information or instructions vital to the operation or maintenance of the equipment.

IMPORTANT

Servicing requires extreme care and knowledge of the

system and should be performed only by a qualified

service technician. For service we suggest you return

the tool to your nearest Sears store or repair center,

Always use original factory replacement parts when

servicing.

WARNING: Do not attempt to operate this tool

until you have read thoroughly and understand

completely all instructions, safety rules, etc.

contained in this manual. Failure to comply can

result in accidents involving fire, electrical shock,

or serious personal injury. Save the owner's

manual and review frequently for continuing safe

operation, and instructingothers who may use

this tool.

READ ALL INSTRUCTIONS

KNOW YOUR POWER TOOL. Read the owner's

manual carefully. Learn the saw's applications

and limitations as well as the specific potentia_

hazards related to this tool.

DO NOT USE IN DANGEROUS ENVIRON-

MENT. Do not use power tools near gasoline or

otherflammable liquids,in damp or wet loca-

tions, or expose them to rain. Keep the work

area well lit.

• MAKE WORKSHOP CHILD-PROOF with

padlocks and master switches or by removing

starter keys

• KEEP CHILDREN AND VISITORS AWAY. All

visitors should wear safety glasses and be kept a

safe distance from work area. Do not let visitors

contact tool or extension cord white operating.

• KEEP THE WORK AREA CLEAN. Cluttered

work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the

saw while it is in operation,

• MAINTAIN TOOLS WITH CARE. Keep tools

sharp and clean for better and safer perfor-

mance. Follow instructions for lubricating and

changing accessories.

• USE THE RIGHT TOOL FOR THE JOB. Do not

force the toolor attachment todo a job itwas not

designed for. Use it onlythe way itwas intended.

• DRESS PROPERLY. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other

jewelry. They can get caughtand draw you into

movingparts. Rubber glovesand nonslipfoot-

wear are recommended. Also wear protective

haircoveringto contain long hair.

• ALWAYS WEAR SAFETY GLASSES WITH

SIDE SHIELDS, Everyday eyeglasses have only

impact-resistant lenses; they are NOT safety

glasses.

• NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the blade is unin-

tentionally contacted.

rRRFTSNRN* TABLESAW315.228110 4

RULES FOR SAFE OPERATION (Continued)

• DO NOT OVERREACH. Keep properfooting and

balance at all times.

SECURE WORK. Use clamps or a vise to hold

work when practical. It's safer than using your

hand and frees both hands to operate tool.

USE THE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.

Use only a cord heavy er_oughto carry the

current your productwill draw. An undersized

cord willcause a drop in linevoltage resultingin

lossof power and overheating.A wire gage size

(A.W.G.) ofat least 14 is recommendedfor an

extension cord 25 feet or less in length. If in

doubt, use the next heavier gage. The smaller

the gage number,the heavier the cord.

AVOID ACCIDENTAL STARTING. Be sure

switch is off when plugging in.

REMOVE WRENCHES AND ADJUSTING

KEYS. Get in the habit ofchecking - before

turningon tool- that hex keys and adjusting

wrenches are removed from tool.

CHECK DAMAGED PARTS. Before using the

tool again, check any damaged parts, including

guards,for properoperation and performance.

Check alignmentof moving parts, binding of

moving parts,breakage of parts, saw stability,

mountingand any other conditionsthat may

affect itsoperation. A damaged part must be

properly repairedor replaced bya qualified

service technicianat a Sears store or repair

center to avoid riskof personal injury.

USE ONLY CORRECT BLADES. Use the right

blade size, style and cutting speed for the

material and the type of cut. Bladeteeth should

point downtoward the front ofthe table.

USE RECOMMENDED ACCESSORIES. Using

improper accessories may riskinjury.

USE ONLY SEARS REPLACEMENT PARTS.

All repairs, whether electrical or mechanical,

shouldbe made by a qualified service technician

at a Sears store or repaircenter.

KEEP GUARDS IN PLACE and in good working

order. This includes the blade guard, riving knife,

and anti-kickback pawls.

CHECK DIRECTION OF FEED. Feed work into

a blade or cutter against the direction of rotation

of the blade or cutter only.

DISCONNECT ALL TOOLS. When not in use,

before servicing, or when changing attachments,

blades, bits, cutters, etc., all tools should be

disconnected from power supply.

• DO NOT FORCE THE TOOL. It will do the job

better and more safely at the rate for which it

was designed.

• NEVER LEAVE TOOL RUNNING UNAT-

TENDED. TURN THE POWER OFF. Do not

leave tool until it comes to a complete stop.

• BEFORE DISCONNECTING THE MOTOR;

unplug the saw from power supply.

WARNING: When servicing, use only identical

Craftsman replacement parts. Use of any other

parts may create a hazard or cause product

damage.

NEVER USE THIS TOOL IN AN EXPLOSIVE

ATMOSPHERE. Normal sparking of the motor

could ignite fumes.

MAKE SURE THE WORK AREA HAS AMPLE

LIGHTING to see the work and that no obstruc-

tions will interfere with safe operation BEFORE

performing any work using this tool.

DO NOT USE TOOL IF SWITCH DOES NOT

TURN IT ON AND OFF. Have defective switches

replaced by a qualified service technician at a

Sears store or repair center

GUARD AGAINST ELECTRICAL SHOCK by

preventing body contact with grounded surfaces

such as pipes, radiators,ranges, refrigerator

enclosures.

• GROUND ALL TOOLS. See Electrical page.

• WEAR A DUST MASK to keep from inhaling fine

particles.

• PROTECT YOUR HEARING. Wear hearing

protection during extended periods of operation.

• DO NOT OPERATE THIS TOOL WHILE UN-

DER THE INFLUENCE OF DRUGS, ALCOHOL,

OR ANY MEDICATION.

STAY ALERT AND EXERCISE CONTROL.

Watch what you are doing and use common

sense. Do not operate tool when you are tired.

Do not rush.

• AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause

your hand to move into the blade. ALWAYS

make sure you have good balance.

• ALWAYS SUPPORT LARGE WORK PIECES

while cutting to minimize risk of blade pinching

and kickback. Saw may slip, walk or slide while

cutting large or heavy boards,

5 CRRFTSMaW TABLESAW315.228110

RULES FOR SAFE OPERATION (Continued)

GUARD AGAINST KICKBACK. Kickbackcan

occur when the blade stalls,drivingthe work

piece back toward the operator. Itcan pull your

hand intothe blade, resultingin serious personal

injury. Stay out ofthe blade path and turn switch

off immediately if blade bindsor stalls.

USE A SUPPORT FOR THE SIDES AND BACK

.OF THE SAW TABLE when sawingwide or long

workpieces. Use a sturdy"outrigger" supportif a

table extension is more than 24 inches longand

is attached tothe saw, to preventtipping.

CUT ONLY WOOD, PLASTIC OR WOOD-LIKE

MATERIALS. Do notcut metal.

• NEVER cut more than one piece at a time. DO

NOT STACK more than one workpiece on the

saw table at a time.

DO NOT REMOVE THE SAW'S BLADE

GUARDS. Never operate the saw with any guard

or cover removed. Make sure all guards are

operating properly before each use.

NEVER PERFORM ANY OPERATION FREE-

HAND. Always place the workpieceto becut on

the saw table and positionitfirmlyagainstthe

fence as a backstop.

USE THE RIP FENCE. Always use a fence or

straight edge guide when ripping.

BEFORE MAKING A CUT, be sure all adjust-

merits are secure.

• BE SURE THE BLADE PATH IS FREE OF

NAILS. Inspectfor and remove all nailsfrom

lumber before cutting. •

• BE SURE THE BLADE CLEARS THE

WORKPIECE. Never startthe saw with the blade

touchingthe workpiece.

• KEEP HANDS AWAY FROM cu'rrlNG AREA.

Do not reach underneath work or in blade cutting •

path with your hands and fingers for any reason.

Always turn the power off.

• USE A PUSH BLOCK OR PUSH STICK for

workpieces so small that your fingers go under

the blade guard. NEVER TOUCH BLADE or

other moving parts during use, for any reason.

,_ WARNING: Blade coasts after being turned off.

ALLOW THE MOTOR TO COME UP TO FULL

SPEED before startinga cut to avoid blade

binding or stalling.

ALWAYS PUSH THE WORKPIECE; never pull it

toward the saw.

DO NOT FEED THE MATERIAL TOO QUICKLY.

Do not force the workpiece againstthe blade.

ALWAYS TURN OFF SAW before disconnecting

it, to avoid accidental starting when reconnecting

to power supply. NEVER leave the table saw

unattended while connected to a power source.

BEFORE CHANGING THE SETUP, REMOVING

COVERS, GUARDS, OR BLADE; unplug the

saw from power supply.

KEEP TOOL DRY, CLEAN, AND FREE FROM

OIL AND GREASE. Always use a clean cloth

when cleaning. Never use brake fluids, gasoline,

petroleum-based products,or any solventsto

clean tool.

KEEP BLADES CLEAN, SHARP AND WITH

SUFFICIENT SET. Sharp blades minimize

stalling and kickback.

USE ONLY OUTDOOR EXTENSION CORDS.

Use only extension cords withthe marking

"Acceptable for use with outdoorappliances;

store cordsindoorswhile not in use." Use

extension cordswith an electrical rating not less

than the saw's rating.Always disconnectthe

extension cordfrom the outletbefore disconnect-

ing the productfrom the extension cord.

INSPECT TOOL CORDS AND EXTENSION

CORDS PERIODICALLY and, ifdamaged, have

repaired by a qualifiedservice technicianat a

Sears store or repair center. Stay constantly

aware ofcord location and keep itwell away

from the moving blade.

DO NOT ABUSE CORD. Never yank cord to

disconnect itfrom receptacle. Keep cord from

heat, oil, and sharp edges.

SAVE THESE INSTRUCTIONS. Refer tothem

frequently and use to instructother users. If you

loan someone thistool, loanthem these instruc-

tions also.

SAVE THESE INSTRUCTIONS

[RAFTSMAN" TABLESAW315.228110 6

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong

grounding plugs and 3-pole receptacles that accept

the tool's plug. When using a power tool at a consid-

erable distance from the power source, use an

extension cord heavy enough to carry the current that

the tool will draw. An undersized extension cord will

cause a drop in line voltage, resulting in a loss of

power and causing the motor to overheat. Use the

chart provided below to determine the minimum wire

size required in an extension cord. Only round jack-

eted cords _isted by Underwdter's Laboratories (UL_

should be used.

Length of Extension Cord Wire Size (A.W.G.)

Up to 25 feet 14

26-100 feet 12

When working with the tool outdoors, use an exten-

sion cord that is designed for outside use. This is

indicated by the letters WA on the cord's jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

_k CAUTION: Keep the cord away from the cutting

area and position the cord so that itwill not be

caught on lumber, tools, or other objects during

cutting operations.

ELECTRICAL CONNECTION

Your Sears Craftsman Table Saw is powered by a

precision built electric motor. It should be connected

to a power supply that is 120 volts, 60 Hz, AC only

(normal household current). Do not operate this tool

on direct current (DC). A substantial voltage drop will

cause a loss of power and the motor will overheat. If

the saw does not operate when plugged into an

out_et,double check the power supply.

SPEED AND WIRING

The no-load speed of your table saw is approximately

4,800 rpm. This speed is not constant and decreases

under a load or with lower voltage. For voltage, the

wiring in a shop is as important as the motor's horse-

power rating. A line intended only for lights cannot

properly carry a power tool motor. Wire that is heavy

enough for a short distance will be too light for a

greater dist.ance. A line that can support one power

tool may not be able to support two or three tools.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current

to reduce the risk of electric shock. This tool is

equipped with an electric cord having an equipment-

grounding conductor and a grounding plug. The plug

must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

Do not modify the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician, improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. The conductor with insulation having an outer

sudace that is green with or without yellow stripes is

the equipment-grounding conductor, if repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to

a live terminal.

Check with a qualified electrician or service personnel

if the grounding instructions are not completely

understood, or if in doubt as to whether the tool is

properly grounded.

Repair or replace a damaged or worn cord immedi-

ately.

This tool is intended for use on a circuit that has an

outlet like the one shown in Figure I. tt also has a

grounding pin like the one shown.

_, WARNING: Electrical shock can kill.

GROUNDING

DOVER OF GROUNDED

OUTLET BOX

Figure 1

7 I"RRFTSMRN" TABLE SAW 315.228110

Anti-Kickback Pawls

Toothed safety devices behind the blade designed to

stop a workpiece from being kicked back at the

operator during a rippingoperation.

Arbor

The shaft on which a blade or cuttingtoolis mounted.

Bevel Cut

A cutting operation made withthe blade at any angle

other than 90" to the saw table.

Compound Cut

A cut with both a miter angle and a bevel angle.

Crosscut

A cuttingoperation made across the grain or the width

of the workpiece.

Dado

A non-throughcut that gives a square notch or trough;

requiresa special blade.

Featherboard

A device to helpguide workpieces duringripcuts.

Freehand (for talole saw)

Dangerous practice ofmaking a cut withoutusing rip

or miter fences. See Safety Rules.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade.

Kerr

The material removed by the blade in a throughcutor

the slot produced by the blade in a non-throughcut.

Kickback

A hazard that can occur when blade binds or stalls,

throwingworkpiece back towardoperator.

Leading End

The end of the workpiece pushed intothe cuttingtool

first.

Miter Cut

A cutting operation made with the miter gage using

any angle other than 0°on the miter gage.

Molding

A non-through cut that gives a varied shape to the

workpiece and requires a special blade.

Push Stick

A device used to feed the workpiece through the saw to

help keep the operator's hands well away from the blade.

Push Block

A device used for non-through cut type operations to

help keep the operator's hands away from the blade.

Rabbet

A notch in the edge of a workpiece.

Resaw

A cutting operation to reduce the thickness of the

workpiece in order to make thinner pieces.

Resin

A sticky, sap-based substance.

Rip Cut

A cut made with the grain of the workpiece.

Saw Blade Path

The area directly in line withthe blade -- over, under,

behind, or in front of it. Also, the workpiecearea

whichwillbe or has been cut by the blade.

Set

The distance thatthe tip of the saw blade tooth is bent

(or set) outward from the face of the blade.

Throw-Back

Saw throwing back a workpiece; similar to kickback.

Through Sawing

Any cutting operationwhere the blade extends

completelythroughthe workpiece.

Trailing End

The workpiece end last cut by the blade in a rip cut.

Workpiece

The itemon which the cutting operation is being done.

The surfacesof a workpiece are commonly referred to

as faces, ends, and edges.

Worktable

The surface on whichthe workpiece rests while

performinga cuttingoperation.

Blade Arbor 5/8 in,

Blade Diameter 10 in.

Blade Tilt 0° -45°

Net Weight Without Leg Stand 75 Ibs,

Net Weight With Leg Stand 97 Ibs,

Rating 120 V, 60 Hz - AC only

Input 15 Amperes

No Load Speed 4,800 RPM

Cutting Capacity with Miter at 0"/Bevel 0°: 3-9/16 in.

Cutting Capacity with Miter at 0VBevel 45°: 2-t/2 in.

CRRFTSNAN"TABLESAW315.228110 8

Your new table saw has been designed to give you

many years of high quality performance. To insure

this goal, proper care and treatment is important.

Careful treatment begins with removing all parts from

the canon and checking them against the list of loose

pans.

Your table saw is shipped complete in one carton and

includes a leg stand, two table extensions, a rip fence,

a miter fence with adjusting clamp, a blade guard, rails

and hardware.

• Separate the saw and all parts from the packing

materials and check each against the packing list,

especially the small parts that can be hidden in the

packing material.

Note: Do not discard the packing materials until you

have carefully inspected the saw, identifiedall

parts, and satisfactorily operated your new saw.

If you are missing a part, check the packaging before

contacting Sears.

If any parts are missing, do not attempt to assemble

your table saw, plug in the power cord, or turn the switch

on until the missing parts are obtained and are installed

correctly. Complete parts lists are lecated at the end of

this manual. Use these lists to identify the part number

of any missing part. Contact your Sears Service Center

or Retail store and get the missing part(s) before

assembling and trying to use your saw.

WARNING: Never use gasoline, naptha, or

other highly volatile solvents. Do not ever let

brake fluids, gasoline, petroleum-based

products, or penetrating oils contact plastic pans.

Such chemicals can weaken or destroy plastic.

WARNING: To prevent accidental starting that

could cause possible serious personal injury,

assemble all parts to your saw before connecting

it to power supply. Saw should never be

connected to power supply when you are

assembling parts, making adjustments, installing

or removing blades, or when not in use.

_1, WARNING: If any parts are missing, do not

operate this tool until the missing parts are

replaced. Failure to do so could result in possible

serious personal injury.

The following recommended accessories are currently available at Sears Retail Stores.

Item No. 9-22210

Item No. 9-22211

Item No. 9-22212

Item No. 9-22213

Item No. 9-22214

Item No. 9_-22215

Item No. 9-22216

Item No. 9-22217

Item No. 9-22218

Item No. 9-22219

Item No. 9_-22220

Router Mounting Kit _1, WARNING: To avoid risk of injury, use

Miter Slot Table recommended dado and zero clearance throat

Ze_'oClearance Throat Plate plate when employing a dado accessory.

Dado Throat Plate

Micro-Position Rip-Fence Accessory

Quick Fold Table

Wide Table Kit

Long Miter/Rip Fence

Air Floatation Table

Wide Table Leg Set

Miter Clamp Kit

DO NOT USE 7 in. WOBBLE DADOES

A complete assortment of blades for your saw are

available at your nearest Sears Retail Store.

,_, WARNING: The use of attachments or accessories not listed might be hazardous.

9 rRRFTSMIIN" TABLESAW315.228110

The following items are included with your Table Saw.

Figure 2

A. Storage Bracket ..................................................... 4

B. Screw (1/4-20 x 1/2 in. Pan Hd.) ............................ 4

C. Lower Brace ........................................................... 4

D. Hex Nut (5/16-18) ................................................. 32

E. Washer (5/16 in.} .................................................. 32

E Leveling Foot .......................................................... 4

G, Leg ......................................................................... 4

H. Carriage Bolt (5/16-18 x 3/4 in.) ........................... 24

I. Upper Brace ........................................................... 2

J. Hex Nut (1/4-20) ..................................................... 8

K. Washer (1/4 in.) .................................................... 12

L. Bolt/1/4-20 x 3/4 in. Hex Hd.) ................................ 4

M. Upper Side Brace ................................................... 2

rRAFTSMIIN" TABLESAW315.228110 10

The following items are included with your Table Saw.

AA/

BB/

Figure 3

N. Front Rail ............................................................ 1

O. Miter Fence Holder With Adjusting Clamp .......... 1

P. Miter Fence With Miter Indicator ........................ 1

Q. Screw .................................................................. 1

R. Rip Scale Indicator .............................................. 1

S. Hex Nut ............................................................... 1

T. End Plug (Front Rail) .......................................... 2

U. End Plug (Rear Rail) ........................................... 2

V. Rip Fence ........................................................... 1

W. Sliding Miter Table .............................................. 1

X. Blade Guard With Riving Knife

And Anti-Kickback Pawls ................................... 1

Y. Accessory Table .................................................. 1

Z. Rear Rail ............................................................. 1

AA. Large wrench ...................................................... 1

BB. Small wrench ...................................................... 1

CC. 3/32 in. Hex Key (Not Shown) ............................ 1

DD. 1/8 in. Hex Key (Not Shown) .............................. 1

EE, 5/32 in. Hex Key (Not Shown) ............................ 1

FIE 3/16 in. Hex Key (Not Shown) ............................ 1

11 CRRFTSMRN"TABLESAW315.228110

The following tools are needed for assembly and alignment. Note: The four hex keys listed below have been

provided with your saw. The remaining tools are typical shop tools and are not included with your saw.

3/8 in. NUT DRIVER

SOCKETWRENCH

WITH7/16in.SOCKET

COMBINATION

SQUARE

FRAMING SQUARE

'U'l'O'l'l'l'l'l,U,l,l,l,l,t, ,_rl,g,f,v,l,l,l,l,l,l,l,U,l,f.

.t.l,',l,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,_.l.,,I.i

ADJUSTABLEWRENCH

#2 PHILLIPS

SCREWDRIVER

FLATBLADE I _

SCREWDRIVER

3/'16in.HEXKEY,---,_-,_,_

5/32in.HEXKEY._.._-_._._

1/8in.HEXKEY._--__

3/32in,HEXKEY_

3/4in.

WRENCH

_ Figure

CRRFTSMRN"TABLESAW315.228110 12

Your saw is designed to perform as a versatile,

accurate, precision cutting tool that is easy to operate.

It is equipped with the following features for safety,

ease of use, and high-quality performance:

• a carbide tipped combination blade

• a bevel indicator to set the exact angle of the blade,

with locking lever

• an adjustable and reversible sliding miter table

• an adjustable miter fence with miter indicator

• an adjustable accessory table

• an adjustable rip fence with scale indicator

• an adjustable riving knife (splitter) and blade guard

with anti-kickback pawls

• front and rear guide rails with an easy-to-read scale

on front rail

• a dust exhaust (2-1/2 in. hole) that can be adapted

to a standard shop vacuum if desired

• blade adjusting handle to set depth of cut

• switch with Iockable cover plate to help prevent

unauthorized use

• aleg stand

These features provide ease of cutting with all types of

wood.

_, WARNING: Before attempting to use your saw,

familiarize yourself with all operating features

and safety requirements.

OPERATING COMPONENTS

The upper portion of the blade projects up through the

table, surrounded by an insert called the throat plate.

To cut wood at a bevel, the blade must be tilted, using

the blade adjustment handTe,scale, and bevel indica-

tor found on the front of the cabinet. Inside the

cabinet, adjustable positive stops control the degree

of movement.

The sliding miter table assembly is used for all cross-

cutting operations. The miter fence is easily adjusted

to cut wood at an angle by loosening the adjusting

clamp, setting the fence to the miter scale, and

retightening the clamp. The sliding miter table, which

rests on a base mounted on the rails, can be reposi-

tioned along the rails for wide work. It can be reversed

for ripping so the projecting base is in the back.

Your saw includes a rip fence and an accessory table.

The accessory table can be moved from the right side

of the saw to the left side as needed. The rip fence is

used to position work that will be cut lengthwise. A

scale on the front rail shows the distance between the

rip fence and the blade.

_lL CAUTION: The saw blade "coasts" after the

saw is turned off.

SPEED AND WIRING

The no-load speed of your table saw is approximately

4,800 rpm. The speed will not remain constant but will

be less under a load. The wiring in a shop is as

important as the motor's horsepower rating. A line

intended for lights only will not properly carry a

power tool motor. Wire that is heavy enough for a

short distance will be too light for a greater distance. A

line that can support one power tool may not be able

to support two or three tools.

_i, WARNING: To prevent possible electrical

hazards, have a qualified electrician check the

line if you are not certain that it is properly wired.

_i, WARNING: Observe all normal safety

precautions related to avoiding electrical shock.

SAFETY DEVICES

Safety devices on your saw include the blade guard,

the anti-kickback pawls, and the riving knife (also

known as a splitter or spreader). The blade guard =sa

clear strong plastic shield designed to prevent acci-

dental contact with the blade. It also deflects any

flying debris from within.

_, WARNING: Although many of the illustrations in

this manualare shownwith the blade guard

removed for clarity,do notoperate the saw

withoutthe blade guard unlessspecifically

instructedto do so.

The riving knife is a metal device directly behind and

above the blade. It is used to help keep the cut wood

from binding together and causing possible kickback. It

is very important to use the riving knife for all through-

sawing operations. The anti-kickback pawls are

toothed plates mounted on the riving knife. Their teeth

point away from the work in case the work should be

pulled back, toward the operator. Then the teeth dig

into the wood to help prevent or reduce the possibility

of kickback.

Your saw features a receptacle on the right side of the

cabinet that permits use of accessories. Use only

accessories that are listed for use with this tool. When

using a listed accessory, unplug the saw motor cord

and use the receptacle and the saws main power

switch to operate the accessory.

13 CRRFTSMRN"TABLESAW315.228110

KNOW YOUR TABLE SAW

BLADEGUARD

SLIDING PAWLS_

MITERTABLE THROATPLATE

SAW BLADE

RIVING KNIFE

MITER SCALE

REARRAIL

RIP FENCE

ACCESSORYTABLE

ADJUST

CLAMP

MITER

FENCE

QUICK-STOP

END CAP

MITER

FENCEHOLDER

STORAGE

BRACKETS)

LOCKINGCLAMPS

LEGSTAND

MITER

TABLE BASE

BEVEL

INDICATOR

FRONTRAIL

HANDLE

NITH

LOCKABLECOVER

BLADE

ADJUSTINGHANDLE

BEVEL

LOCKINGLEVER

LEVELINGFOOl

Figure5

CRAFTSMAN"TABLESAW315,228110 14

POWER SWITCH

See Figure 6.

Your saw is equipped with a switch that utilizes a

Iockable switch cover to prevent unauthorized use.

With the saw turned Off, a padlock can be used to

secure the switch cover over the switch. This prevents

anyone from starting your saw without removing the

padlock, lifting the switch cover, and pressing the

switch button.

TO TURN YOUR SAW ON:

• Lift switch cover.

• Press switch button.

• Lower switch cover.

TO TURN YOUR SAW OFF:

• (A) Press or push outside of switch cover, or

(B) Lift switch cover and press switch button.

TO LOCK YOUR SAW SWITCH:

• Raise switch cover.

• Align metal loop through slot in switch cover while

lowering switch cover.

• Place shackle of padlock (not provided) through

the metal loop and close padlock.

_1= W ARNING: Always make sure your workpiece

=snot in contact with the blade before operating

the switch to start the tool. Failure to heed this

warning may cause the workpiece to be kicked

back toward the operator and result in serious

personal injury.

,_ WARNING: To reduce the risk ofaccidental

starting, Always make sure the switch is in the

Off position before pluggingtoolintothe power

source.

BLADES

See Figure 7.

For maximum performance, it is recommended that

you use the Craftsman 40 tooth, 10 inch carbide

tipped combination blade provided with your saw. It is

a high-quality carbide tipped combination blade

suitable for ripping and crosscut operations. Other

recommended blades are listed in the accessory

section of this manual.

Check with your nearest Sears Retail Store for other

high quality blades as they become available.

_k CAUTION: Be sure to use only blades that are

rated for at least 5,500 rpm and recommended

for use on this saw. Check with your nearest

Sears retail store.

CARBIDE

TEETH

SWITCH

_TO START

(B)

TO LOCK IN

OFF POSITION

PADLOCK

(NOTPROVIDED)

Figure 6

BLADE ROTATION

Figure 7

15 CRRFTSMRN"TABLESAW315.228110

Assembly is best done in the area where the saw will be used. When you remove the table saw base, loose

parts, and hardware from the packing materials, check all items with the loose parts list and drawing. If you are

unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until

you have obtained the missing part(s).

A. ASSEMBLY OF LEG STAND, STORAGE

BRACKETS, AND MOUNTING TO SAW

ASSEMBLING LEG STAND

See Figures 8 and 9

• Take the fottowing hardware from theteg stand

hardware bag:

24 carriage bolts (5/16-18 x 3/4 in)

4 leveling feet

32 fiat washers (5/16 in)

32 hex nuts (5/16-18)

Note: Remaining hardware from this bag is used for

mounting leg stand on the table saw base and

mounting storage brackets to upper brace.

• Take 4 legs and 8 braces from loose parts.

• Place an upper side brace inside two of the legs,

with the legs wide end up. (Upper side braces have

two large holes in each end.) Make sure the two

posts on the leg align with the small holes on the

brace.

Align the two large holes on the brace and the

legs. Insertthe carriage bolts. Add flat washers

and hex nuts and hand tighten. Repeat for the

other upper brace. These are the front and back

sets.

• For the side sets, install a upper brace on two legs.

Add hardware and finger tighten. Repeat for the

other upper brace.

• Use the same steps to install the lower braces.

Tighten all hex nuts with a 12 mm wrench.

• Place a hex nut and flat washer on each leveling

foot. Install the leveling feet from the bottom of

UPPERBRACE

BOLT HEXNUT

CARRIAGE

BOLT

LEG

STORAGE LOWERBRACE

BRACKET(S)

LEVELINGFOOT--_'_ HEX

WASHER

NUT

Figure 8

CRAFTSMAN"TABLESAW315.228110

each leg with the bolts pointing up. Cap with the

remaining fiat washers and hex nuts but do not

tighten.

• Move the leg set to desired location. Adjust the

leveling feet with a 12 mm wrench, then tighten the

top hex nut.

ASSEMBLING STORAGE BRACKETS

See Figure 8,

• Take storage brackets from loosepads.

• Take the followinghardware fromthe leg stand

hardware bag:

4 screws (1/4-20 x 1/2 in. Pan Hd.)

4 hex nuts (1/4-20)

4 washers (1/4 in.)

STORAGEBRACKET(S)

UPPER

BRACE

• Place the saw tabte upside down on a smooth

surface, such as cardboard, on the floor.

_i, WARNING: Do not lift the saw without help.

The saw base weighs approximately 75 Ibs. Hold

it close to your body. Keep your knees bent and

lift with your legs, not your back. Ignoring these

precautions can result in back injury.

• Place the leg stand on the table saw base. Align

the holes in the table with the holes in the end

braces.

• Place a flat washer on a bolt and insert through

hole. Add a flat washer and a hex nut. Hand

tighten. See Figure 10.

• Repeat for three remaining hotes. Tighten aU

hardware with a 12 mm wrench. You may find it

helpful to use one wrench to hold the head of the

bolt and one to tighten the hex nut.

LOWERBRACE

LEGSTANDASSEMBLED Figure 9

• Secure storage brackets to upper braces of leg

stand as shown in figures 8 and 9.

Note: If you mount the saw base on a bench instead

of the legs, go to the Assembly of Rails, Tables,

Fences procedure. The bench surface must

have an opening for sawdust to fall through, as

large as the opening in the bottom of the saw

base. A height ot 36 in. from the top of the saw

table to the floor is recommended.

MOUNTING THE LEG STAND ON THE TABLE

SAW BASE

See Figure 10.

• Take the followingfrom a smaUhardware bag:

4 hex bolts (1/4-20 x 3/4 in.)

4 hex nuts (1/4-20)

8 flat washers {114-20 in.)

Note: This hardware was in the bag with hardware for

assembling the leg stand and leveling feet.

SAW BASE

FLAT

LEGSTAND

HEXNUT

HEXBOLT

Figure 10

17 CRAFTSMAN"TABLESAW315.228110

WARNING: Do not connect to power supply

until assembly is complete. Failure to comply

could result in accidental starting and possible

serious injury.

B.ASSEMBLY OF RAILS, TABLES, AND

FENCES

TO INSTALL FRONT AND BACK RAILS

• Position end caps on both rails and secure in place

by tapping with a block of wood or a rubber mallet.

• Loosen the front rail clamps one-half (1/2) turn

from the tightened position. Loosen the square rail

holder nut one-fourth (1/4) turn to allow the front

rail to slide over it. See Figures 11and 12.

• Mount the front rail with the scale facing the

outside toward the operator.

• Check to make sure the rail clamps will securely

clamp the rail before sliding the entire assembly

into position. If not, repeat steps 2 and 3 above.

• Slide the rail into position over both clamps and

secure.

• Mount the rear rail, following the same clamping

procedure as shown for the front rail. Orient the

rear rail as shown in figure 12.

TO INSTALL MITER TABLE AND FENCE

• Install the slidingmiter table assembly over the

front and rear rails. See Figure 13. Check that it

slides easily on the rails. Push both front miter

locking clamps down evenly on each side to

secure. Repeat for both rear miter locking clamps.

Note: Do riot force miter locking clamps fully

down. Tighten only to flat "seated" position.

• To install the miter fence holder to the miter fence,

loosen the attachment bolt by turning the adjusting

clamp (the knob on top) counterclockwise. Make

sure the adjusting clamp is loose enough so the

bolt has enough clearance to slide in the table slot.

Slide the tabs into the grooves in the miter fence.

See Figure 14.

• Mount the miter fence to the miter table by install-

ing the Iocator pin (below the miter fence) into hole

"A" or "B". (Hole "A" is closest to the blade). At the

same time, place the attachment bolt in the slot.

Secure the adjusting clamp, but do not tighten.

Note: Hole "A" should be used fo,_short pieces of

wood and hole "B" shouSdbe used for Songpieces

of wood.

• Adjust the miter indicator to the scale.

• Retighten the adjusting clamp.

FRONT

RAILCLAMP

ENDCAP FRONTRAIL

SCALE

LOCKING

LEVER BLADE

ADJUSTING HANDLE Figure 11

ENDCAP REAR RAIL

RAi

HOLDERNUT

Figure 12

REAR

RAIL

MRER

TABLE BASE

Figure 13

CRAFTSMAN"TABLESAW315.228110 18

TO INSTALL ACCESSORY TABLE AND RIP

FENCE

m! Place the accessory table on the front and rear rails,

fitting the tip into the rear rail. Position the slot on the

underside of the accessory table onto the front rail

and tighten the lever securely. See Figure 15.

• Screw the locking handle into the rip fence mounting

hole. See Figure 16.

• Remove the scale indicator assembly from the plas-

tic bag and install on either side of the fence. The

pan head screw (#8-32 x 1/2 in.) goes on the outside

of the front block. The scale indicator and hex nut

(#8-32) go immediately behind the front lip of the front

block.

• To install the rip fence, place the rear lip on the rear

rail and pull slightly toward the front of the unit. Lower

front end onto the guide surfaces on top of the front

rail. Check for a smooth gliding action. Swing the

locking handle down to automatically align and se-

cure the fence. When securely locked, the locking

handle should point downward.

,_, WARNING: Do not connect to power supply

until assembly is complete. Failure to comply

could result in accidental starting and possible

serious injury.

C.BLADECHECKAND BLADE GUARD

ASSEMBLY

TO CHECK SAW BLADE INSTALLATION

• To check the saw blade, first remove the three

screws holding the throat plate in place. Remove

the throat plate. See Figure 17.

• Make sure the bevel locking lever is securely pushed

to the left. Raise the blade arbor to its full height by

turning the blade adjusting handle clockwise.

• Using the smaller hex wrench, insert the flat open

end into the flats on the arbor shaft as shown in

figure 18. Insert the larger hex wrench over the hex

nut, and, holding both wrenches firmly, pull the

larger wrench forward to the front of the machine to

loosen and push to tighten. Make sure the blade

nut is securely tightened. Do not overtighten.

Note: Arbor shaft has left hand threads.

• Check all clearances for free blade rotation.

• See To Set the Scale to the Blade in the

Operation Section. In cutting operations, the scale

will be set to the side of the blade where the cut

will be measured and made.

ADJUSTINGCLAMP

MITERFENCE ATrACHMENT

BOLT

MITER FENCE

INDICATOR

HOLE "B"

TABLESLOT

ACCESSORY

TABLE

Figure 14

REARRAIL

UNLOCK_

FIT LIP OFTABLE

INTO REAR RAIL

LOCK LEVER

FRONT

RAIL

RIP FENCE

Figure 15

REARLIP

REARRAIL

SCREW HEX NUT

LOCKING HANDLE

SCALE INDICATOR FRONTLIP

Figure 16

19 I:RRFTSNRN" TABLESAW315.228110

TO INSTALL BLADE GUARD

[] To install the blade guard, firstremove the three

screws holding the throat plate in place. Remove

the throat plate. See Figure 17.

• Make sure that the locking lever is securely pushed

to the left. Raise the blade arbor to its full height by

turning the blade adjusting handle clockwise.

[] Move the locking lever to the right for Angle mode.

Slowly turn the blade adjustment handle to put the

blade at 30 degrees. The handle will "pop out"

slightly as it engages the clutch.

• Holding the blade adjusting handle with one hand,

use the other hand to push the locking lever firmly

to the left to lock the angle.

• Using Me smaUhex wrench, install the blade guard

by loosening the two attachment hex nuts enough

to slide the riving knife down between the shims.

Do not remove the hex nuts. See Figure 19.

Partially retighten the two attachment nuts. Check

the blade and riving knife alignment.

• Correctly align the blade and riving knife as shown,

repeating step 5 as needed. Tighten attachment

nuts securely. If riving knife is not positioned

correctly, with blade up, it could contact saw table

when blade is lowered and restrict blade elevation.

[] Blade alignmentwith the riving knife can be

adiusted for different blade widths. Refer to

Settings and Adjustments in the Operations

Section.

[] Check the blade guard assembly for clearances

and free movement. Reinstall the throat plate into

the opening, lower the blade and secure the three

attachment screws. Tighten the screws securely.

SMALLHEX

LARGE

HEXWRENCH

THROATPLATE

Figure 17

NOTE: PLACE BLADEBETWEEN

INNER ANDOUTER BLADEWASHER

LARGE SMALLHEX

HEXWRENCH WRENCH_

LARGESPACER

ARBOR

ARBORNUT

INNER

BLADEWASHER

OUTER

BLADEWASHER

,TO

TIGHTEN

Figure 18

RIVING

MOUNTING

PLATE

Figure t9

CRmFTSMRN"TABLESAW315,228110 20

Page is loading ...

Craftsman 315228110 User manual

Brand: Craftsman

Model: 315228110

Category: Power tools

Type: User manual

This manual is also suitable for

315.22811

Download PDF

report

Craftsman 315228110 User manual

This manual is also suitable for

Craftsman 315228110 User manual

Related papers

Other documents