LG PQRCVSL0QW.ENCXUAE Installation guide

ENGLISH

LG

New Wide Wired Remote Controller

LG

IMPORTANT

• Please read this owner's & installation manual completely

before installing the product.

• Installation work must be performed in accordance with the

national wiring standards by authorized personnel only.

• Please retain this owner's & installation manual for future

reference after reading it thoroughly.

Owner's & Installation Manual

Models: PQRCVSL0

PQRCVSL0QW

P/No.: MFL62129202

ITALIANO ESPAÑOL

FRANÇAIS

DEUTSCH

êìëëäàâ

PORTUGUÊS

Safety Precaution

Owner’s & Installation Manual 3

ENGLISH

2 New Wide Wired Remote Controller

New Wide Wired Remote Controller Owner’s & Installation Manual

TABLE OF CONTENTS

Safety Precaution .....................................................................................................................................................3

Part Description........................................................................................................................................................4

Installation Instructions...........................................................................................................................................5

Group control .........................................................................................................................................................7

Installer Setting - How to Enter Installer Setting Mode...........................................................................................8

Installer Setting - Test Run Mode.........................................................................................................................11

Installer Setting - Setting Address of Central Control...........................................................................................12

Installer Setting - E.S.P. .......................................................................................................................................13

Installer Setting - Thermistor ................................................................................................................................15

Installer Setting - Ceiling Height Selection ...........................................................................................................16

Installer Setting - Static Pressure Setting.............................................................................................................17

Installer Setting - Remote Controller Master/Slave Setup ...................................................................................18

Installer Setting - Override Master/Slave Setting .................................................................................................19

Installer Setting - Dry Contact Mode Setting ........................................................................................................20

Installer Setting - Zone State................................................................................................................................21

Installer Setting - Celsius / Fahrenheit Switching.................................................................................................22

Installer Setting - Zone Type Setting....................................................................................................................23

Installer Setting - Zone Number Setting ...............................................................................................................24

Installer Setting - Emergency Heater Setting ......................................................................................................25

Installer Setting - Option Function Setting............................................................................................................27

Installer Setting - Static Pressure Step Setting ....................................................................................................28

Owner's Instructions..............................................................................................................................................29

Standard Operation - Standard Cooling...............................................................................................................29

Standard Operation - Power Cooling ...................................................................................................................30

Standard Operation - Heating Mode ....................................................................................................................30

Standard Operation - Dehumidification Mode ......................................................................................................31

Standard Operation - Fan Mode ..........................................................................................................................31

Standard Operation - Auto Operation Mode ........................................................................................................32

Standard Operation - Temperature Setting/Room Temperature Check ..............................................................33

Standard Operation - Airflow Setting....................................................................................................................34

Sub function - Direct Wind / Indirect Wind .........................................................................................................35

Sub function - Plasma Purification .......................................................................................................................37

Sub function - Humidifier......................................................................................................................................38

Sub function - Electric Heater ..............................................................................................................................39

Sub function - Energy-Saving Cooling Operation ................................................................................................40

Sub function - Robot Cleaning Manual Setup ......................................................................................................41

Function setting - Child Lock................................................................................................................................42

Function setting - Robot Cleaning Automatic Setup ............................................................................................43

Function setting - Filter Sign Clear.......................................................................................................................44

Function setting - Elevation Grill ..........................................................................................................................45

Function setting - Vane Angle Control .................................................................................................................46

Function Setting - Change Temp .........................................................................................................................47

Function setting - Zone Control............................................................................................................................48

Function setting - Changing Current Time ..........................................................................................................49

Function setting - Auto Cleaning .........................................................................................................................51

Function Setting – WLAN(Wireless LAN) Module Access Point mode ................................................................52

Programming - Simple Reservation .....................................................................................................................53

Programming - Sleep Reservation .......................................................................................................................54

Programming - ON Reservation...........................................................................................................................55

Programming - OFF Reservation ..................................................................................................

.......................57

Programming - Weekly Reservation ....................................................................................................................59

Programming - Holiday Reservation ....................................................................................................................61

Ventilation Product User Manual - Interlinked Air Conditioner and Ventilation ....................................................62

Ventilation Product User Manual - Interlinked Operation with General Ventilation ..............................................63

Manual Conversion ..............................................................................................................................................64

Ventilation Product User Manual - Interlinked Operation with Direct Expansion Ventilation................................65

Ventilation Product User Manual - Single Operation with Direct Expansion Ventilation ......................................66

Ventilation Product Additional Operations - Fast / Power Saving ........................................................................67

Ventilation Product Function Settings ..................................................................................................................68

Ventilation Product Reservations Settings ...........................................................................................................69

Ventilation Product Installer Setting Functions - Entering Method .......................................................................70

Different Mode Drive ............................................................................................................................................71

Self-diagnosis for Trouble Mode ..........................................................................................................................72

Outage Compensation Function ..........................................................................................................................72

Troubleshooting Steps .........................................................................................................................................73

Entrust installation of the

product to a licensed HVAC

technician. Failure to do so may

result in fire, electric shock,

explosion, and/or physical injury.

• It will cause fire or electric shock

or explosion or injury.

All requests for replacement

or reinstallation should be to

a licensed HVAC technician.

• It will cause fire or electric shock

or explosion or injury.

Do not disassemble, fix,

and/or modify products

randomly.

• It will cause fire or electric shock.

Do not place flammable

substances close to the

product.

• It will cause fire.

Do not allow water to run

into the product.

• It will cause electric shock or

breakdown.

Do not give the shock to the

product.

• It will cause breakdown when

giving the shock to the product.

n Installation

Safety Precaution

• The installation requires expert skills, and it should be installed by the service center or other shops specialized

in the installation and recognized by our company.

• For all the problems arising after installation by someone who has no relevant qualifications, our company will

not provide free service.

• The following safety precautions are provided to prevent unexpected dangers or losses.

: If the user does not follow the mandatory items, it may result in serious injury or death.

: If the user does not follow the mandatory items, it may cause personal injury or property

damage.

: Warnings and Cautions are to call the user’s attention to the possible danger. Read and follow

them carefully in order to prevent a safety accident.

: Warning and Caution are indicated in this guide and the product itself to help protect the users

from danger.

WARNING

CAUTION

WARNING

n In-use

Refer to the service center or installation

specialty store when the product becomes wet.

• It will cause fire or electric shock.

Do not give the shock using sharp and

pointed objects.

• It will cause breakdown by damaging parts.

n In-use

CAUTION

Entrust installation of the

product to a licensed HVAC

technician. Failure to do so may

result in fire, electric shock,

explosion, and/or physical injury.

• It will cause fire or product

deformation.

Do not press hard against

the screen, and only select

more than one button at a

time if instructed to do so in

the user instructions.

• It will cause product breakdown or

malfunction.

Do not touch or pull the lead

wire with wet hands.

• It will cause product breakdown or

electric shock.

1

4

5

7

11

10

9

8

2

3

6

13

12

14

15

Attach the appropriate language information label

inside the front door for convenient access.

Owner’s & Installation Manual 5

ENGLISH

4 New Wide Wired Remote Controller

Installation Instructions

2

1

3

1. Please fix tightly using the provided screws after placing remote controller setup

board on the place where you plan to place the remote controller.

- Please set it up not to bend because poor setup could take place if setup board bends.

Please set up remote controller board fit to the reclamation box if there is a reclamation box. is unclear and

needs to be heavily reworded.

- Install the product so as not to make a gap with the wall side to prevent shaking after the installation.

2. The wired remote controller can be set up in three different directions.

- Direction: through the wall, top, or right.

- If setting up the remote controller cable to exit through the top or right side, be sure to remove the plastic from

the guide grooves from the remote controller case.

h

Remove guide groove with long nose.

①

Through the wall

②

Through the top

③

Through the right side

Installation Instructions

Part Description

Name and Function of Remote Controller

OPERATION INDICATION

SCREEN

SET TEMPERATURE BUTTON

FAN SPEED BUTTON

ON/OFF BUTTON

OPERATION MODE SELECTION

BUTTON

WIRELESS SIGNAL (IR)

RECEIVER FOR WIRELESS

REMOTE CONTROLLER

• Only Operate with ceiling Duct

type indoor unit

AIR FLOW BUTTON

SUBFUNCTION BUTTON

FUNCTION SETTING BUTTON

VENTILATION BUTTON

RESERVATION

UP,DOWN,LEFT,RIGHT BUTTON

• To check the indoor temperature,

press button.

ROOM TEMPERATURE BUTTON

SETTING/CANCEL BUTTON

EXIT BUTTON

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Connection Cable

(1EA, 10m)

Screw

(4 EA)

Owner's / Installation

manual

Inform label

(8EA-8Languages)

Accessories

j Some functions may not be operated and displayed depending on the product type.

Wire guide grooves

Owner’s & Installation Manual 7

ENGLISH

Installation Instructions

6 New Wide Wired Remote Controller

Installation Instructions

GND

12V

Signal wire

GND

12V

B Y R B Y R

MASTER SLAVE

Signal wire

GND

12V

Signal wire

Group control

1. When installing more than 2

units of air conditioner to one

wired remote controller, please

connect as pictured to the right

• This needs more clarification before

it can be edited

• Check for event communication

through the product manual.

2. When installing more than 2 wired remote

controllers to one air conditioner, please

connect as pictured to the right.

• When installing more than 2 units of wired

remote controller to one air conditioner, set

one wired remote controller as master and the

others all as slaves, as shown in the right

picture.

• You cannot control the group as shown in the

right for some products.

• Refer to the product manual for more details.

When controlling multiple indoor units with event communication function with one remote

controller, you must change the master/slave setting from the indoor unit.

- When changing the master/slave configuration, changes will take effect after the unit is turned

on after being powered off for one minute.

- For ceiling type cassette and duct product group, change the switch setting of the indoor PCB.

- For wall-mount type and stand type indoor units, change the master/slave setting with the

wireless remote controller. (Refer to wireless remote controller manual for details)

h When installing 2 remote controllers to one indoor unit with event communication function, set

the master/slave of the remote controller. (Refer to remote controller master/slave selection)

When in a slave setting, some functions(fan speed, lock and time setting) may not be available.

When simultaneously connecting

2 sets of wired remote controller

• When controlling in groups, set the master/slave of the remote controller. Refer to Installer

setting section on how to set master/slave for more details.

#3 switch OFF: Master

(Factory default setting)

#3 switch ON: Slave

Wall

Side

Wall

Side

Wall

Side

Wall

Side

Connecting order

Separating order

3. Place the top part of the remote controller into

the setup board you have screwed into the wall,

as pictured to the right, and connect the pieces

by pressing the bottom into the board.

- Arrange the cable through the top or right guide grooves before

closing if necessary, and do not leave a gap between the

remote controller and the setup board.

To separate the remote controller from the

setup board, insert a flathead screw driver into

the separation holes on the bottom of the

remote controller and turn clockwise to release

the remote controller.

- There are two separating holes on the remote controller, and

they should be separated individually. Make sure not to

damage any interior components with the screwdriver when

separating.

4. Please connect indoor unit and remote controller using connection cable.

5. Please use an extension cable if the distance between the wired remote controller

and indoor unit is more than 10m.

Please check if connector is normally connected.

Connecting cable

Indoor

Unit side

When installing the wired remote controller, do not bury it in the wall.

(It can cause damage in the temperature sensor.)

Do not install the cable to be 50m or above.

(It can cause communication error.)

• When installing the extension cable, check the connecting direction of the connector of the remote controller

side and the product side for correct installation.

• If you install the extension cable in the opposite direction, the connector will not be connected.

• Specification of extension cable: 2547 1007 22# 2 core 3 shield 5 or above.

CAUTION

• Installation work must be performed in accordance with the national wiring standards by authorized

personnel only.

• Installations must comply with the applicable local/national or international standards.

• Apply a totally enclosed noncombustible conduit (metal raceway) if local electric and building codes require

plenum cable usage.

CAUTION

12V Red

Signal Yellow

GND Black

Owner’s & Installation Manual 9

ENGLISH

8 New Wide Wired Remote Controller

Installation Instructions

Installer Setting Code Table

1) General air-conditioner product

j Some contents may not be displayed depending on the product function

Installation Instructions

If the installation is not done correctly it can cause injury to the user or damage to your property.

Installation must be done by a certified HVAC technician, and any problems arising from improper

installation are the owner’s financial responsibility.

CAUTION

Installer Setting - How to enter installer setting mode

Function Code Value

Pressing and holding the button for

3 seconds enters the remote controller

setup mode. If it is not held for 3

seconds, it enters the user setup mode.

- If pressing once shortly, it enters into

user setup mode. Please press more

than 3 seconds for sure.

1

When you enter the setting mode

initially, Function code is displayed on

the bottom of the LCD screen.

2

No. Function Code Value

1 Test Run 01 01:Set

2 Address Setting 02 00~FF : Address

01:VeryLow 0 ~ 255

02:Low

3 E.S.P. Value 03

03:Med

04:High

05:Very High

01:Remo

4 Thermistor 04 02:Indoor

03:2TH

01:Low

02:Med

5 Ceiling Height 05

03:High

04:Very High

01:V-H

02:F-H

6 Static Pressure 06

03:V-L

04:F-L

7 Master Setting 07

00:Slave

※ If only “Plus1” series models 00 : Group setting

01:Master

01 : Single setting

8 Override Setting 08

00:Slave

01:Master

9 Dry Contact 09

00:Auto-Off

01:Auto-On

10

Release 3 Min.

10 01:Set

Delay

11 Zone State 11

01:Variable

02:Fixed

12

Celsius

12

00:Celsius

(Optimized only for U.S.A)

Fahrenheit Switching 01:Fahrenheit

13 Zone Type 13

00:Zone Controller

01:Damper Controller

14 Zone Number 14 02~04(Zone number)

Emergency Heater

15

Setting

18

16 Plasma 20

17 Electric heater 21

18 Humidifier 22

00: Not Installed

19 Elevation Grill 23

01: Installed

20 Ventilation Kit 24

21 Auxiliary Heater 25

22

Static Pressure

32

00: use static pressure (code 06) set value

Step 01~ 11: static pressure step (code 32) set value

Function Code ESP valueESP step

•

Some categories of the menu may not be displayed according to the function of the

product, or the menu name may be different.

Select mode Setup Low Ambient Heating Operation Setup FAN Speed

00 : not use 0 : not use 0 : fan off

01 : use 1 : use – compressor off(0℉/-18℃)/on(5℉/-15℃) 1 : fan on

2 : use – compressor off(5℉/-15℃)/on(10℉/-12℃)

3 : use – compressor off(10℉/-12℃)/on(15℉/-9℃)

Owner’s & Installation Manual 11

ENGLISH

Installation InstructionsInstallation Instructions

Function Code Set

Press button to start.

3

During the test run, pressing the below

buttons will exit the test run:

- Select operation, temperature

up/down, wind flow control, wind

direction, start/stop button.

4

Pressing and holding the button for

3 seconds enters the remote controller

setup mode. If it is not held for 3 seconds,

it enters the user setup mode.

- Please cancel the right and left of wind

direction for RAC product.

1

Setup figure '01' blinks at the lower part

of indication window.

2

Installer Setting - Test Run Mode

After installing the product, you must run a Test Run mode.

For details related to this operation, refer to the product manual.

10 New Wide Wired Remote Controller

2) General Ventilation product

j Some contents may not be displayed depending on the product function

No. Function Code Value

1 Test Run 01 01 : Test Run Setup

2 02 00~FF : Address of Central Control

3 SA(Supply Air) ESP 03 <ESP level> <ESP value> <Example>

4 EA(Exhaust Air) ESP 04

01 : Low 0~255

02 : High

03 : Super High

5 Product Direction 05

01 : Normal

02 : Opposite

6 Quick Refresh Priority 06

01 : Supply Air First

02 : Exhaust Air First

7 Master Setting 07

00 : Slave

01 : Master

8 Override Setting 08

00 : Slave

01 : Master

9 Dry Contact 09

00 : Auto-Off

01 : Auto-On

10 Release Of 3 Minute Delay 10 01 : Set

11 Zone State 11

01 : Variable

02 : Fixed

12

Humidification for Singular

13

00 : Not in Use

Ventilation 01 : Use

13

Humidification for Heat Mode

14

00 : Automatic

Ventilation 01 : Manual

Address Setting

Function Code ESP valueESP step

Owner’s & Installation Manual 13

ENGLISH

12 New Wide Wired Remote Controller

Installation Instructions

If entering into ESP setup mode by using

button, it indicates as pictured below.

2

Select ESP fan step by pressing

button. (01: very low, 02: low,

03: medium, 04: high, 05: very high)

3

Move to ESP value setting by pressing

button.

(It is 000 when delivered

from the warehouse.)

4

Press button to setup ESP value.

(It is possible to set up ESP

value from 1 to 255, and 1 is

the smallest and 255 is the

biggest.)

5

Function code,

ESP code

ESP value

Pressing and holding the

button for 3 seconds enters the

remote controller setup mode. If it

is not held for 3 seconds, it enters the

user setup mode.

1

Function Code ESP value

ESP step

Installer Setting - E.S.P.

• If ESP is set incorrectly the air conditioner may malfunction, which is why this setting should only be

done by a certified technician.

This function allows the wind strength for each fan speed level to be set manually.

It's the function to use for connecting central control.

Please refer to central controller manual for the details

Function Code

Group No

Indoor No.

Set Group No. by pressing

button.(0~F)

3

Move to Indoor No. setting option

by pressing button.

4

Set Indoor No. by pressing

button.

5

Press button to save.

6

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

7

If entering into address setup mode by using

button, it indicates as pictured below.

2

1

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user

setup mode.

Installation Instructions

Installer Setting - Setting Address of Central Control

•

When setting ESP value on the product without very weak wind or power wind function, it

may not work.

Owner’s & Installation Manual 15

ENGLISH

14 New Wide Wired Remote Controller

Installation Instructions

Function Code Thermistor setting

Set Thermistor value by pressing

button. (01: Remote Controller,

02: Indoor, 03: 2TH)

3

Press button to save.

4

5

If moving to room temperature perception

sensor selection menu by pressing

button, it indicates as pictured below.

2

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user setup

mode.

1

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

Installer Setting - Thermistor

j The function of 2TH has different operation characteristics according to the product.

Temperature sensor selection Function

01 Remote controller Operation in remote controller temperature sensor

02 Indoor unit Operation in indoor unit temperature sensor

03 2TH

Cooling

Operation of higher temperature by comparing indoor unit's and wired

remote controller’s temperature.

(There are products that operate at a lower temperature.)

Heating

Operation of lower temperature by comparing indoor unit's and wired remote

controller's temperature.

Thermistor Table

Installation Instructions

Function code,

ESP code

ESP value

Press button to save.

7

Select ESP fan step again by using

button and set up the ESP value, as No.

4 and 5, that corresponds to each wind

flow.

6

Pressing the button will exit the

settings mode. If is not pressed, the

remote controller will automatically exit

setup mode after 25 seconds with no

input. If the set button is not pressed, the

changes will not take effect.

8

• Please be careful not to change the ESP value for each fan step.

• It does not work to setup ESP value for very low/power step for some products.

• ESP value is available for specific range belongs to the product.

This is the function to select the temperature sensor to judge the room temperature.

Owner’s & Installation Manual 17

ENGLISH

16 New Wide Wired Remote Controller

Installation Instructions

Function Code Pressure

Press and hold the button

for 4 seconds to enter the

installer setting mode. The timer

will display 01:01.

1

Select static pressure by pressing

button.

(01:V-H, 02:F-H, 03:V-L, 04:F-L)

3

Press button to save.

4

5

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input.

If the set button is not pressed, the changes

will not take effect.

If pressing button repeatedly, it

moves to static pressure selection menu

as pictured below.

2

Installer Setting - Static Pressure Setting

This function is applied to only duct type indoor units. Setting this in other cases will cause malfunction.

Pressure selection

Function

Zone state ESP standard value

01 V-H Variable High

02 F-H Fixed High

03 V-L Variable Low

04 F-L Fixed Low

Static Pressure Setting Table

Function Code Thermistor setting

Select ceiling height value by pressing

button. (01:Low, 02:Medium,

03:High, 04:Very high)

3

Press button to save.

4

5

If moving to ceiling height selection menu by

pressing button, it indicates as pictured

below.

2

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user setup

mode.

1

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

Installation Instructions

Installer Setting - Ceiling Height Selection

This function is to adjust FAN Airflow rate according to ceiling height (for ceiling type product)

• Ceiling height setting is available only for some products.

• Ceiling height of ‘Very high’ function may not exist depending on the indoor unit.

• Refer to the product manual for more details.

Ceiling Height Level Description

01 Low Decrease the indoor airflow rate 1 step from standard level

02 Medium Set the indoor airflow rate as standard level

03 High Increase indoor airflow rate 1 step from standard level

04 Very high Increase indoor airflow rate 2 steps from standard level

Ceiling Height Selection Table

Owner’s & Installation Manual 19

ENGLISH

18 New Wide Wired Remote Controller

Function Code Master/Slave

Select Master/ Slave by pressing

button.

(00: Slave, 01 : Master)

3

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user setup

mode.

1

If pressing button repeatedly, it moves to

override master/slave selection menu as

pictured below.

2

Press button to save.

4

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

5

Installation Instructions

Installer Setting - Override Master/Slave Setting

Override master/slave selection function to prevent indoor units operate as cooling and heating mode

at same time.

Override slave set indoor units are operated flow master indoor unit’s mode.

Installation Instructions

Installer Setting - Remote Controller Master/Slave Setup

Function Code Master/Slave value

Select Master/ Slave by pressing

button.

(00: Slave, 01: Master)

3

Press button to save.

4

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user

setup mode.

1

If pressing button repeatedly, it moves to

master/slave selection menu as pictured

below.

2

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

5

It is a function for settings in group control, or 2-remote controller control.

Remote controller Function

Master

Indoor unit operates based on master remote controller at group control.

(Master is set when delivered from the warehouse.)

Slave

Setup all remote controllers except one master remote controller to slave at

group control

• When controlling in groups, basic operation settings, airflow strength weak/medium/strong,

lock setting of the remote controller, time settings, and other functions may be restricted.

h Refer to the 'group control' part for details

h Override master/slave selection function is possible to use only when it is connected to the

succeeding models of Multi-V 7 series.

• If it is set as Override Slave, icon

is displayed on LCD Display Window. (See Figure 1)

Figure 1.

Owner’s & Installation Manual 21

ENGLISH

20 New Wide Wired Remote Controller

Function Code Zone State

fixing mode

Select Zone State rate fixing mode by

pressing button.

(01: Variable, 02: Fixed)

3

Press button to save.

4

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user

setup mode.

1

If moving to ceiling height selection menu by

pressing button, it indicates as pictured

below.

2

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

5

Installation Instructions

Installer Setting - Zone State

It is the function to setup indoor unit's wind flow to variable or fixed.

- Variable : Comp ON, setup airflow. Comp OFF, weak wind

- Fixed : Comp ON, setup airflow. Comp OFF, setup airflow

Installation Instructions

Installer Setting - Dry Contact Mode Setting

Function Code Dry Contact

setting value

Select Dry contact setting by pressing

button.

(00 : Manual, 01 : Automatic)

3

Press button to save.

4

Pressing and holding the button

for 3 seconds enters the remote

controller setup mode. If it is not held

for 3 seconds, it enters the user setup

mode.

1

If pressing button repeatedly, it moves to

remote controller dry contact mode setup

menu as pictured below.

2

Pressing the button will exit the settings

mode. If is not pressed, the remote

controller will automatically exit setup mode

after 25 seconds with no input. If the set

button is not pressed, the changes will not

take effect.

5

Dry contact function is the function that is possible to use only when dry contact equipment is

separately purchased/setup.

• Please refer to dry contact manual for more details.

Owner’s & Installation Manual 23

ENGLISH

Installation Instructions Installation Instructions

22 New Wide Wired Remote Controller

Installer Setting - Celsius / Fahrenheit Switching

Function Code conversion mode value

Press repeatedly until it shows

Function code 12.

2

Select Temperature unit mode by

pressing button.

(00: Celsius, 01: Fahrenheit)

3

Press button to save or release.

4

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is

not pressed, the changes will not take

effect.

5

1

Pressing and holding the button for

3 seconds enters the remote

controller setup mode. If it is

not held for 3 seconds, it enters

the user setup mode.

Function Code Zone type value

Repeat pressing button to select

Function code 13.

Ex) Setting the Zone Type as "New"

2

Select Zone Type by pressing

button

(00:Old, 01:New)

3

Press button to save or release.

4

1

Pressing and holding the button for

3 seconds enters the remote

controller setup mode. If it is

not held for 3 seconds, it enters

the user setup mode.

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is

not pressed, the changes will not take

effect.

5

This function is used for switching the display between Celsius and Fahrenheit.

h Whenever press button in Fahrenheit mode, the temperature will increase/drop 2

degrees.

Installer Setting - Zone Type Setting

This function is only available on some products.

It is possible to set up a new zone or select an old one to install the damper controller.

If you set zone number incorrectly, the product may malfunction especially in zone control.

This function must carried out by a certificated-technician.

CAUTION

Owner’s & Installation Manual 25

ENGLISH

24 New Wide Wired Remote Controller

Installation Instructions Installation Instructions

Function Code Zone Number installed

Press repeatedly until it shows

Function code 14.

Ex) Setting the Zone Number for "2"

2

Select Zone Number by pressing

button

(02~04 : number of zone installed)

3

Press button to save or release.

4

1

Pressing and holding the button for

3 seconds enters the remote

controller setup mode. If it is

not held for 3 seconds, it enters

the user setup mode.

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is

not pressed, the changes will not take

effect.

5

Installer Setting - Zone Number Setting

This function is only available on some products.

Zone Number is to set the number of installed zones. It is possible to control only in zone new type

Installer Setting - Emergency Heater Setting

This function is only available on some products

This function will set the Emergency Heater Setting.

Emergency Heater is used to heat the space in emergency case such as heat pump error.

Emergency heat is in place of and does not supplement heat pump.

※ Emergency Heater setting Function sets following conditions:

1) Emergency Heater operation while in error or outdoor unit operates cooling cycle.

2) Emergency Heater operation in Low Ambient temperature

3) Fan speed setting during Emergency Heater operation

This function setting must be carried out by a certified-technician.

Incorrect function setting can cause fire.

CAUTION

Function Code

Setting1: Heater Operation while in error or

outdoor unit operates cooling cycle.

Press repeatedly until it shows

Function code 18.

2

Select mode of Heater Operation while

in error by pressing button

00: not use

01: use

ƓIf 00 is set at this stage, setting 2 and

setting 3 will not be available

3

Setting2 : Low Ambient

Heating Operation

Setting3 : FAN Speed

Setting during Emergency

Heater Operation

Setting1 : Heater

Operation while in error

or outdoor unit operates

cooling cycle.

1

Pressing and holding the button for

3 seconds enters the remote

controller setup mode. If it is

not held for 3 seconds, it enters

the user setup mode.

Owner’s & Installation Manual 27

ENGLISH

Move to Low Ambient Heating Operation

setting by pressing button.

4

Press button to setup Low

Ambient Heating Operation.

5

Press button to save.

8

Move FAN Speed Setting during

Emergency Heater Operation by pressing

button.

6

Press button to setup FAN

Speed during Emergency Heater

Operation.

7

0 : not use

1 : use - compressor off(0℉/ -18℃) / compressor on(5℉ / -15℃)

2 : use - compressor off(5℉ / -15℃) / compressor on(10℉ / -12℃)

3 : use - compressor off(10℉/ -12℃) / compressor on(15℉ / -9℃)

0 : fan off

1 : fan on

ƓEmergency heater operation in Low Ambient temperature

- compressor off : Emergency heater enabled

- compressor on : Emergency heater disabled

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is

not pressed, the changes will not take

effect.

9

26 New Wide Wired Remote Controller

Installation Instructions Installation Instructions

Installer Setting - Option Function Setting

Function Code Existing condition

Select existing condition

of each mode by pressing

button.

(00: not installed,

01 : installed)

3

Press button to save.

4

If pressing button repeatedly, it moves to

the selected option function code as pictured

below.

2

Function

Plasma purification

Electric heater

Humidifier

Elevation grill

Ventilation kit

Auxiliary heater

Code

20

21

22

23

24

25

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is

not pressed, the changes will not take

effect.

5

1

Pressing and holding the button for

3 seconds enters the remote

controller setup mode. If it is

not held for 3 seconds, it enters

the user setup mode.

Setting feature for indoor unit when Plasma purification / Electric heater / Humidifier / Elevation grill

Ventilation kit / Auxiliary heater is newly installed, or installed unit is removed.

Owner’s & Installation Manual 29

ENGLISH

28 New Wide Wired Remote Controller

Standard Operation - Standard Cooling

Press button to turn on the

indoor unit.

1

Press button to select

Cooling operation mode.

2

Adjust the desired temperature

by pressing buttons.

Press button to check the

Room temperature.

When setting the desired

temperature higher than room

temperature, only ventilation

wind is blows out instead of

cooling wind.

3

h Setting Temp Range : 18-30°C (64-86°F).

It cools the room by comfortable and clean wind.

Owner's Instructions

Installation Instructions Owner's Instructions

Press button for 4 seconds to

enter the installer setting mode until

timer segment displays “01:01”.

1

Pressing button will exit settings mode.

❈ After setup, it automatically gets out of

setup mode if there is no button input for

25 seconds.

❈ When exiting without pressing set button,

the manipulated value is not reflected.

5

If pressing button repeatedly, it

moves to static pressure selection menu

as picture below.

2

Select static pressure by pressing

button.

00: use static pressure (code 06) set value

01~ 11: static pressure step (code 32) set value

3

Press button to save.

4

Function Code pressure

Installer Setting - Static Pressure Step Setting

This function is applied to only duct type. Setting this in other cases will cause malfunction.

This function is only available on some models.

This is the function that static pressure of the product is divided in 11 steps for setting.

• Static Pressure (Code 06) setting will not be used if Static Pressure Step (Code 32)

setting is being used.

• For the static pressure value for each step, refer to the indoor unit in the product

manual.

Owner’s & Installation Manual 31

ENGLISH

30 New Wide Wired Remote Controller

Owner's Instructions

Press button to turn on the

indoor unit.

1

Press button to select

Dehumidification mode.

The temperature setting cannot be

adjusted during operation this mode.

2

Press the button to select

airflow rate SLO → LO → MED

→ HI → AUTO.

(The initial wind powerfulness of

humidity removal drive is 'weak'.)

3

Press button to turn on the

indoor unit.

1

Press button to select Fan

Mode.

2

Every time pressing button, you

can select wind flow in order of

SLO

→ LO → MED → HI → SHI.

When running ventilation,

compressor of the air handling unit

does not work.

3

Standard Operation - Fan Mode

It removes humidity while air-cooling slightly

It blows the air as it is in the indoor, not the cold wind.

• In rainy season or high humidity climate, it is possible to operate simultaneously dehumidifier and

cooling mode to remove humidity effectively.

• The menu item of wind powerfulness might not be partially selected according to the product.

• Ventilation drive does not release cool wind but general fan

• Because it releases the wind that has no temperature difference from the room, it functions to

circulate the inside air.

• The menu item of wind powerfulness might not be partially selected according to the product.

Standard Operation - Dehumidification Mode

Owner's Instructions

Press button to trun on the

indoor unit.

1

Press button to select

cooling operation mode.

2

Press button until ‘Po’ is

displayed.

3

It makes the room cool using pleasant and fresh air quickly

It supplies warm wind to the indoor

Standard Operation - Heating Mode

Press button to turn on the

indoor unit.

1

Press button to select

Heating mode.

(To check the indoor temperature,

press the room temperature button.)

2

Adjust the desired temperature

by pressing buttons.

When setting the desired

temperature lower than room

temperature, there is only

ventilation wind.

3

What is Power Cooling?

• Power Cooling cools the room quickly by blowing 18°C(64°F) air at the most powerful fan speed

available.

h

Partial product has no power air-cooling function.

• Heating drive only operates for the heating and cooling models.

• Heating does not operate at cooling exclusive model.

Standard Operation - Power Cooling

Owner’s & Installation Manual 33

ENGLISH

32 New Wide Wired Remote Controller

Owner's Instructions

Standard Operation - Temperature Setting/Room Temperature Check

We can simply adjust the desired

temperature.

• Press the buttons to adjust the

desired temperature.

: Increases the temperature

: Decreases the temperature

Cooling operation:

- The cooling mode does not work if

desired temperature is higher than room

temperature Please lower the desired

temperature.

Heating operation:

- The heating mode does not work if desired

temperature is lower than room

temperature Please increase the desired

temperature.

1

When you press the button, the room

temperature will be displayed for 5

seconds.

After 5 seconds, it turns to display the

desired temperature.

The location of the remote controller

may cause the remote to display a

different temperature than you

experience elsewhere in the room.

1

Temperature Setting

Room Temperature Check

• For air-cooling drive, from 18℃(64℉) to 30℃(86℉), and for heating drive, from 16℃(60℉) to

30℃(86℉), you can select desired temperature.

• 5℃(10℉) is proper for the difference between room and outside temperature.

• Room temp: Indicates the current room

temperature.

• Set temp: Indicates the temperature that user

want to set.

Owner's Instructions

Press button to turn on the

indoor unit.

1

Press button to select

Artificial intelligence Mode.

2

You can adjust

the temperature

as the picture on

the right for

cooling and

heating model.

3

For the case of

cooling exclusive

models, as the

picture on the

right, you can

adjust the temperature

from hot to cold, from

"-2" to "2" based on "00".

4

When cold

When cool

When appropriate

When warm

When hot

Standard Operation - Auto Operation Mode

During operating Auto Operation mode:

• We can use the FAN SPEED button

• We can change manually to other operation mode.

Owner’s & Installation Manual 35

ENGLISH

34 New Wide Wired Remote Controller

Sub function - Direct Wind / Indirect Wind

It is the function to directly or indirectly control wind direction by body perception sensor.

The icon of direct/indirect wind

blinks on the display, and then, if

pressing button, direct/indirect

wind icon is fixed and the function

is setup.

2

1

Please press the button.

The method to setup direct/indirect wind

3

Pressing the button exits the

setup mode.

direct wind

indirect wind

Owner's Instructions

Standard Operation - Airflow Setting

Please setup desired fan speed by

fan speed button.

• Every time you press fan speed,

you can select the wind flow in

order of ‘SLO → LO → LO MED → MED →

MED HI → HI → SHI → AUTO’.

• Air flow setting function might be different

according the types of indoor unit

• Please refer to product manual for product’s

detailed function.

1

Please set desired wind direction

by pressing button.

You can select wind direction of

(comfortable wind → Up/Down and

Right/Left → Right/Left →

Up/Down) by pressing the button.

Partial item of wind directions might not be

selected according to product function.

Please refer to product manual for product’s

detailed function.

1

Wind powerfulness : You can simply adjust

desired wind powerfulness.

Wind direction : You can simply adjust desired

wind direction.

Owner's Instructions

Owner’s & Installation Manual 37

ENGLISH

36 New Wide Wired Remote Controller

• Plasma purification is a additional function and it might not be available on all types of indoor unit

• Cleaning air function is possible only when product is running.

• If you want independent cleaning air drive, please set up cleaning air by pressing additional drive

button at ventilation drive.

Owner's Instructions

Sub function - Plasma Purification

Press the button until the

icons flashes.

The method to setup cleaning air

1

Operate or cancel Plasma

Purification function by pressing

button.

( icon appears/disappears on

display part up

to selection )

2

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is

not pressed, the changes will not take

effect.

3

Only products with humidifying function can use this.

Owner's Instructions

The icon of direct/indirect wind

blinks on the display, and then, if

pressing button, direct/indirect

wind icon is removed and the

function is cancelled.

2

1

Please press the button.

The method to cancel direct/indirect wind

3

Pressing the button will exit the

settings mode. If is not pressed,

the remote controller will

automatically exit setup mode after 25

seconds with no input. If the set button is not

pressed, the changes will not take effect.

direct wind

indirect wind

• Direct/indirect wind is a additional function and it might not be available on all types of

indoor unit

Owner’s & Installation Manual 39

ENGLISH

38 New Wide Wired Remote Controller

Sub function - Electric Heater

Press the button until the

icons flashes.

1

Turn on/off ELECTRIC HEATER

by pressing button (The

icon is displayed when set and

disappears when cancelled).

2

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller

will automatically exit setup

mode after 25 seconds with no

input. If the set button is not

pressed, the changes will not

take effect.

3

It is a function to strengthen the heating ability by turning on the electric heater during the heating

operation.

It can only be set during heating operation.

Owner's Instructions

• Heater function is additional function and it only operates in selected models.

• The indoor unit product with Auxiliary Heater function set automatically displays (0) icon during

the AUXILIARY HEATING OPERATION.

When using non-heat recovery out door unit , emergency heater can be turned on for

simultaneous heating and cooling. Indoor units with the emergency heater must be turned OFF for

simultaneous cooling and heating.

※Heater function is additional function and it only operates in selected models.

Emergency heater can be turned on while in error code in case of emergency.

Electric heater icon is displayed on LCD display window with error code when emergency heater is

on while in error.

※Exception case: Error code 1,3,9,10

※If the previous mode of the Indoor unit is COOL, DRY, or FAN ONLY mode, heater must be

turned on manually.

Sub function - Humidifier

Press the button until the

icons flashes.

1

Turn on/off HUMIDIFIER by

pressing button (The icon

is displayed when set and

disappears when cancelled).

2

Pressing the button will exit

the settings mode. If is not

pressed, the remote controller will

automatically exit setup mode

after 25 seconds with no input. If

the set button is not pressed, the

changes will not take effect.

3

Only products with humidifying function can use this.

Owner's Instructions

• Humidification function might not be available on all types of indoor unit.

Page is loading ...

LG PQRCVSL0QW.ENCXUAE Installation guide

LG PQRCVSL0QW.ENCXUAE Installation guide

in other languages

Related papers

Other documents