Warning
EN-1 TV LCD-TFT Owner’s Manual
Warning
CAUTION
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
RISK ELECTRIC SHOCK
DO NOT OPEN
!
The lightning ash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
!
Caution:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do q
not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN THOSE SPECIF ED HEREIN MAY q
RESULT IN HAZA DOUS RADIATION EXPOSURE. (This item is only for TV with DVD models.)
Important Safety Instructions
Read t1. hese instructions.
Keep these instructions.2.
Heed all warnings.3.
Follow all instructions.4.
Do not use this apparatus near water.5.
Clean only with dry cloth.6.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.7.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including 8.
amplifiers) that produce heat.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the 9.
point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.10.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with 11.
the apparatus. When a cart is used, use caution when moving the cart/ Apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.12.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged 13.
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, 14.
shall be placed on the apparatus.
The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the apparatus 15.
normal use.
Class I apparatus shall be connected to a mains socket outlet with a protective earthing connection.
Safety Instructions
TV LCD-TFT Owner’s Manual EN-2
Safety Instructions(for TV with DVD)
FCC WARNING:
This equipment may generate or use radio frequency energy.Changes or modications to this equipment may
cause harmful interference unless the modications are expressly approved in the instruction manual.The user
could lose the authority to operate this e uipment if an unauthorized change or modication is made.
LASER SAFETY:
This unit employs a laser.Only a qualied service person should remove the cover or attempt to service this
device,due to possible eye injury.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION:
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.DO NOT
STARE INTO BEAM.
LOCATION: INSIDE,NEAR THE DECK MECHANISM.
Energy Star compliant
By being Energy Star compliant you are assured that your Haier model is helping the
environment by using less energy while saving you money. ENERGY STAR is a joint
program of the U.S. Environmental Protection Agency and the U.S. Department of Energy
promoting energy efficiency.
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Haier product. This easy-to-use manual will guide you in getting the best use of your
product. Remember to record the model and serial number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
Contents
EN-3 TV LCD-TFT Owner’s Manual
Contents
Lock Menu Options............................................16
Function................................................................................. 17
PC Menu Options...............................................18
USB Input ...........................................................19
To play pictures................................................................... 19
To play music ....................................................................... 20
To play pictures and music together........................... 20
DVD Operation ..................................................21
Basic Playback ..................................................................... 21
Advanced Playback ........................................................... 21
Special Function Playback .............................................. 22
DVD System Setup............................................................. 23
Playable Discs...................................................................... 24
Discs Protection and DVD Characteristics................. 24
Maintenance 25
Specification 26
Troubleshooting 26
Warranty 27
Warning 1
Safety Instructions 2
Introduction 4
Controls ................................................................4
Connection Options ............................................5
Remote control ....................................................5
Installation 8
External Equipment Connections ......................8
Accessories..............................................................................8
Antenna Connection............................................................8
Choose Your Connection................................................. 10
Connecting a VCR............................................................... 10
External A/V Source Setup.............................................. 10
Conmponent Setup........................................................... 10
Connecting a computer................................................... 10
Cable TV Setup.................................................................... 10
HDMI input........................................................................... 10
Operation 11
Switching On/O the TV set........................................... 11
Choose the Menu Language.......................................... 12
Choose the Input source ................................................. 12
Video Menu Options..........................................12
Function................................................................................. 12
Audio Menu Options .........................................13
Function................................................................................. 13
Channel Menu Options .....................................13
Function................................................................................. 13
Function Menu Options ....................................14
Function................................................................................. 15
Introduction
TV LCD-TFT Owner’s Manual EN-4
DVD panel controls
Introduction
Controls
This is a simplied representation of the TV front panel, side panel control buttons and side inputs.
TV Side panel controls and connections
R1series
K1series F1series P1series
INPUT MENU VOL- VOL+ CH- CH+ POWER
R1
K1
DVD
slot
load
series
series
STOP:
Press to stop the DVD disc.
PLAY/PAUSE:
Press to play the DVD program disc, and press again
to pause the DVD program.
OPEN/CLOSE:
Press to open the disc tray, and press again to close
the tray.
PREV:
Press to play the previous program.
NEXT:
Press to play the next program.
1
POWER Press to turn on and o the TV.
2
INPUT
Press to access the input source mode. Press
repeatedly to change the source to the one
you want to watch. In the MENU screen, the
INPUT button serves as the ENTER button.
3
MENU
Menu display. Press to access the on-screen
menu display.
4
VOL +/-
Press to adjust the volume. In the MENU screen,
these buttons serve as left/right buttons.
5
CH+/-
Connect a USB ash drive to view JPEG images
or listen to MP3 songs.
6
Power indicator
7
Remote Sensor
Receivers IR signals from the remote control.
Do not put anything near the sensor, which
may block the remote control signal.
Insert DVD with label
towards back (Silver “shiny”
side facing towards you.)
Introduction
EN-5 TV LCD-TFT Owner’s Manual
Connection Options
Back panel connections
COMPONENT IN
PP Yrb
ATN IN R-AUDIO-L R-AUDIO IN-L
PC AUDIO IN
VGA IN IMDHBSU
S-VIDEO IN
VIDEO
1
Antenna
Input
Connect cable or antenna signals to the TV,
either directly or through your cable box.
2
DVI Audio In
When using a DVI to HDMI adapter, connect the
audio signal to these jacks.
3
AUDIO In
Connect the audio L/R cables from the video
signal source to these jacks.
4
S-VIDEO In
Connect the S-Video cable from an external
signal source to this jacks.
5
AUDIO In
Connect the audio L/R cables from the video
signal source to these jacks.
6
VIDEO In
Connect the video signal from a video device to
this jack.
7
USB input
Connect a USB ash drive to view JPEG images or
listen to MP3 songs.
8
VGA Video In
Connect a video cable from a computer to this
jack.
9
VGA Audio
In
Connect the audio L/R cables from a computer to
this jack.
0
HDMI In
Connect a HDMI device to receive digital audio and
uncompressed digital video.
A
Component
Input
Connect a component video device to these jacks.
Remote Control
Battery loading
1. Slide open the cover of the battery compartment on
the back of the remote controller.
2. Load two 7# (AAA) alkaline batteries in the
compartment, (plus and minus poles to respective mark)
3. Replace the cover of the battery compartment.
Introduction
TV LCD-TFT Owner’s Manual EN-6
1
PICTURE Press repeatedly to cycle through the available picture modes
2
ARC
Select the aspect ratio
3
CCD (closed caption) Select a closed caption option
4
INPUT Show the input source
5
MENU Press to open the on-screen menu
6
Thumbstick (Up/Down/
Left/Right)
Volume/Channel Selection, Allows you to navigate the on-screen
menus and adjust the system settings to your preference.
7
EXIT
Clears all on-screen displays and returns to TV viewing from any
menu
8
USB
Press to switch input source to USB in
9
USB PLAY/PAUSE
0
USB fast reverse
A
USB fast forward
B
DISPLAY
Press to display the TV status information on the top of the TV screen
C
GUIDE
Display the guide when you are watching analog or digital channels
D
Power Press to turn on and o the TV
E
AUDIO Press to cycle through dierent sound settings
F
SLEEP button Press to display the sleep timer option
G
MTS/SAP Select MONO, STEREO, SAP in NTSC system
H
Number buttons Press to change a channel
I
tCVUUPO
Press to select digital channels. For example, to enter “54-3”,
QSFTTiwitwBOEiw
J
MUTE
Switches the sound on or o
K
ENTER
Accesses the highlighted item in the on-screen menu
L
RECALL
Press to jump back and forth between two channels
M
USB REPEAT
N
USB STOP
O
USB Next Chapter
P
USB Previous Chapter
Q
CH.LIST Open the channel list in TV
R
FAVORITE Open the favourite channel list in TV
(For TV without DVD)
PICTURE
CCD
INPUT
ARC
MENU
VOL-
EXIT
USB
PLAY/PAUSE
REV
DISPLAY GUIDE
MTS/SAP
CH+
CH-
VOL+
ENTER
STOP
PREV
FAVORITE
AUDIO
SLEEP
REPEAT
NEXT
CH.LIST
MUTE
RECALL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Red
UP DOWN LEFT RIGHT
Green
Yellow
Blue
Color buttons
When functions are attached to the
color buttons, the color buttons are
shown on screen.
Remote control
The remote control cannot be operated unless the batteries are properly loaded.
When using the remote control, aim it at the remote sensor on the TV.
Precautions
As strong light may interfere the signals, change your
position to operate the remote controller if the television
cannot be turned on or o as you expect.
Keep the remote controller away from heat source
or humid area to ensure eective performance of the
remote controller.
Make sure that two AAA alkaline batteries are loaded.
The batteries must be of the same type. The batteries
must be located properly. The batteries are not
rechargeable.
Make sure that there is no obstacle between the remote
controller and television set.
Introduction
EN-7 TV LCD-TFT Owner’s Manual
Remote control
The remote control cannot be operated unless the batteries are properly loaded.
When using the remote control, aim it at the remote sensor on the TV.
1
Power Press to turn on and o the TV
2
USB Press to switch input source to USB in
3
GUIDE
Display the guide when you are watching analog or digital channels
4
CCD (closed caption) Select a closed caption option
5
PICTURE Press repeatedly to cycle through the available picture modes
6
AUDIO Press to cycle through dierent sound settings
7
INPUT
Show the input source
8
MUTE
Switches the sound on or o
9
VOLUME UP/DOWN
Press to adjust the volume
0
MENU
Press to open the on-screen menu
A
Thumbstick (Up/Down/
Left/Right)
Allows you to navigate the on-screen menus and adjust the
system settings to your preference
B
SLEEP button
Press to display the sleep timer option
C
DVD/USB PLAY/PAUSE
D
DVD Open/close
E
DVD/USB FAST FORWARD
F
DVD/USB FAST REVERSE
G
DVD CALL
H
DVD MENU
I
DVD SEARCH
J
DVD ANGLE
K
DVD Mode
L
CH.LIST
Open the channel list in TV
M
MTS/SAP
Select MONO, STEREO, SAP in NTSC system
N
FAVORITE
Open the favourite channel list in TV
O
ARC
Select the aspect ratio
P
Number buttons Press to change a channel
Q
tCVUUPO
Press to select digital channels. For example, to enter “54-3”,
QSFTTiwitwBOEiw
R
RECALL Press to jump back and forth between two channels
S
CHANNEL UP/DOWN
Press to scan between the last two channels, press and hold
down either +/--
T
EXIT
Clears all on-screen displays and returns to TV viewing from any
menu
U
ENTER
Accesses the highlighted item in the on-screen menu
V
DISPLAY
Press to display the TV status information on the top of the TV screen
W
DVD/USB STOP
X
DVD/USB REPEAT
Y
D
VD/USB Previous Chapter
Z
DVD/USB Next Chapter
[
DVD AUDIO Mode
\
DVD SETUP
]
DVD PROGRAM
`
DVD SUBTITLE
(For TV with DVD)
OPEN/CLOSE
PLAY/PAUSE
REV
D.MENU
SEARCH
D.CALL
ANGLE
D.AUDIO
SUBTITLE
ENTER
STOP REPEAT
PREV NEXT
SETUP
PROGRAM
USB
GUIDE
INPUT
MUTE
VOL CH
MENU
YALPSIDPEELS
EXIT
RECALL
PICTURE AUDIO ARC FAVORITE
CCD MTS/SAP CH.LIST
DVD
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
7
8
9
10
11
12
13
14
15
16
17
Installation
TV LCD-TFT Owner’s Manual EN-8
Installation
External Equipment Connections
Accessories
Remote control Owner’s manual Alkaline battery (AAA)
x
2
Antenna Connection
Over-the-air TV reception quality will depend on your antenna type, antenna location and antenna positioning.
ANT IN
VHF Antenna
UHF Antenna
Turn clockwise to tighten
Bronze Wire
Be careful not to bend the bronze wire
when connecting the antenna.
Bronze Wire
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor Antenna
To improve the picture quality in a poor signal
area, please purchase a signal amplifier and install
properly.
If the antenna needs to be split for two TV’s, install a
“2-Way Signal Splitter” in the connections.
To install the antenna properly please contact a
professional in your area.
Note
All cables shown are not included with the TV.R
PLAY/PAUSE
REV
REPEAT
GUIDE
MTS/SAP
CCD ARC
FREEZE
ENTER
STOPUSB REC
PREV NEXT
CH.LIST
FAVORITE
TV
STB
INPUT
MUTE
VOL CH
MENU
SLEEP DISPLAY
EXIT
RECALL
PICTURE AUDIO PC HDMI
CABLE VCR AUD
DVD
ANT IN
Installation
EN-9 TV LCD-TFT Owner’s Manual
Choose Your Connection
There are several ways to connect your television,
depending on the components you want to connect
and the quality of the signal you want to achieve. The
following are examples of some dierent ways to
connect your TV with dierent input sources.
Connecting a VCR
To avoid picture noise (interference), leave an adequate
distance between the VCR and TV.
COMPONENT IN
PP Y
rb
ATN IN R-AUDIO-L R-AUDIO IN-L
S-VIDEO IN
VIDEO
VCR
1
2
Connection Option 1
Set VCR output switch to channel 3 or 4 and then tune
the TV to the same channel number.
Connection Option 2
Connect the audio and video cables from the VCR’s A
output jacks to the TV input jacks, as shown in the
figure. When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white, and
Audio Right = red). If you connect a S-VIDEO output
from VCR to the S-VIDEO input, the picture quality is
improved; compared to connecting a regular VCR to
the Video input.
Insert a video tape into the VCR and press
B PLAY on
the VCR. (Refer to the VCR owner’s manual.)
Select the input source with using the
C INPUT button
on the remote control, and then press
/
button
to select the source, press ENTER button to confirm.
External A/V Source Setup
How to connect
Connect the audio and video cables from the A
external equipment’s output jacks to the TV input
jacks, as shown in the figure.
When connecting the TV to external equipment,
B
match the jack colors (Video = yellow, Audio Left =
white, and Audio Right = red).
R-AUDIO IN-L VIDEO
How to use
Select the input source with using the A INPUT button
on the remote control.
Operate the corresponding external equipment.
B
Refer to external equipment operating guide.
Component Setup
How to connect
Connect the DVD video outputs (COMPONENT) to A
the Y Pb Pr jacks on the TV and connect the DVD
audio outputs to the YPbPr Audio IN jacks on the TV,
as shown in the figure.
If your DVD only has an S-VIDEO output jack, connect B
this to the S-VIDEO input on the TV, as shown in the
figure.
Note
If your DVD player does not have R
component video output, use S-Video.
Installation
TV LCD-TFT Owner’s Manual EN-10
&20321(17 ,1
33 <UE
5$8',2/
69,'(2 ,1
How to use
Turn on the DVD player, insert a DVD disc.A
Use B INPUT button on the remote control to select
proper input.
Connecting a computer
How to connect
To get the best picture quality, adjust the VGA A
graphics card to 1024s 768.
Use the TV’s VGA or DVI (Digital Visual Interface) B
Audio IN port for audio connections, depending on
your computer connector.
If the graphic card on the computer does not
q
output analog and digital RGB simultaneously,
connect only one of either VGA IN or HDMI IN to
display the VGA on the TV.
If the graphic card on the computer does output q
analog and digital RGB simultaneously, set the TV
to either VGA or HDMI; (the other mode is set to
Plug and Play automatically by the TV.)
Then, make the corresponding audio connection.
C
If using a sound card, adjust the VGA sound as
required.
3& $8',2 ,1
9*$ ,1
How to use
Turn on the computer and the TV.A
Use INPUT on the remote control to select VGA or B
HDMI source.
Check the image on your TV. There may be noise
C
associated with the resolution, vertical pattern,
contrast or brightness in VGA mode. If noise
is present, change the VGA mode to another
resolution, change the refresh rate to another rate
or adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the VGA
graphic card can not be changed, change the VGA
graphic card or consult the manufacturer of the VGA
graphic card.
Note
Use a DVI cable.R
Avoid keeping a fixed image on the TV’s screen R
for a long period of time. The fixed image may
become permanently imprinted on the screen.
The synchronization input form for Horizontal and
R
Vertical frequencies is separate.
ResolutionY
Mode Resolution
Frame
frequency
(Hz)
VGA
640s480
60Hz
SVGA
800s600
60Hz
75Hz
XGA
1024s768
60Hz
75Hz
Cable TV Setup
After subscribing to a cable TV service from a local
provider you can watch cable TV programming. The TV
cannot display TV programming unless a TV tuner
device or cable TV converter box is connected to the TV.
For further information regarding cable TV service,
contact your local cable TV
service provider(s).
Connection Option 1
Operation
EN-11 TV LCD-TFT Owner’s Manual
Select 3 or 4 with channel switch on cable box. A
Tune the TV channel to the same selected output B
channel on cable box.
Select channels at the cable box or with the cable
C
box remote control.
Connection Option 2
Connect the audio and video cables from the Cable A
Box's output jacks to the TV input jacks, as shown in the
gure.When connecting the TV to a Cable Box, match
the jack colors (Video = yellow, Audio Left = white, and
Audio Right = red).
Select the input source by using the
B INPUT button
on the remote control or on the TV.
Select your desired channel with the remote control
C
for cable box.
HDMI input
How To Connect
Connect the cables from the external equipment's
output jacks to the TV input jacks, as shown in the gure.
How To Use
Select the input source by using A INPUT button on
the remote control or on the TV.
Operate the corresponding external equipment.
B
Refer to external equipment operating guide.
Operation
In the manual, the OSD (on screen display) may be
dierent from your TV’s, because it is just an example to
help you with the TV operation.
There are several options you might need to set up in
order for your TV to work properly. Read the instructions
that follow.
Switching On/O the TV set
First, connect power cord correctly.A
Select the viewing source by using B INPUT button on
the remote control.
When finished using the TV, press
C POWER button on
the remote control. The TV reverts to standby mode.
If you intend to be away on vacation, disconnect the
D
power plug from the wall power outlet.
Note
If the TV in power on , the screen show information R
according the type of input signal, the information
will disappear. If there is no signal, “No Signal” will
display on the screen.
Choose the Menu Language
When you start using your set for the first time, you must
select the language which will be used for displaying
menus and indications.
Choose
A TV Input and then press MENU button.
Press
B
/
button to select Function menu.
PressC
or ENTER button and then use
/
button to select Language.
PressD
/
button to select language.
( English, Spanish or French)
Function
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
DPMS
Blue Screen On
On
Time Setup
Closed Caption
Default
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
/
COMPONENT IN
PP Yrb
ATN IN R-AUDIO-L R-AUDIO IN-L
S-VIDEO IN
VIDEO
Operation
TV LCD-TFT Owner’s Manual EN-12
Choose the Input source
Change the picture source so you can watch your
TV, VCR, DVD, Cable , or any other devices that are
connected to your TV.
Press A INPUT button to enter the Select Source menu
and then use
/
button to select the desired
items (TV, Video1, Video2, S-Video, Component1,
Component2, DVD, PC, HDMI).
Press B ENTER button to confirm .
Video Menu Options
Picture quality can be adjusted for any input
separately .
The picture quality on the screen can be adjusted as
follows:
Press
A MENU button and then use
/
button
until the Video menu appears on the screen.
Press
B
/ ENTER button to enter the menu function
and
/
button to scroll up and down to select
the desired function.
Press
C
/ ENTER button to conrm and
/
button increase and decrease the level to
adjust the selected option to your preference.
Repeat step 2 and step 3 until desired picture quality
D
has been achieved.
Video
Audio
Channel
Lock
Function
Video
Mode Custom
Brightness
Contrast
Color
Tint
Sharpness
Color Temperature
Advanced Video
50
50
50
0
50
Select
BackAdjust
EXIT
ENTER
/
Note
The options may be dierent because of the inputs.R
Symbols on top of the menu in this manual may R
dier from the actual set display.
The picture options can be changed only in Custom R
mode, the other modes are xed.
Function
ModeY :
Select the type of picture which best
corresponds to your viewing requirements by
selecting picture mode in Video menu. You may
select the picture mode directly by pressing the
PICTURE button on the remote control.
Brightness: Y Press
/
button and
/ ENTER
button to conrm, then press
/
button to
adjust the brightness of the picture.
Contrast: Y Press
/
button and
/ ENTER
button to conrm, then press
/
button to
adjust the contrast of the picture.
Color: Y Press
/
button and
/ ENTER button
to conrm, then press
/
button to adjust
the color saturation.
Tint: Y Adjust the tone of the picture.
Sharpness: Adjust the amount of the detail
enhancement, the image sharpness rises as the
number increases (By increasesing the level, it will
show cleaner and clearer images and by descreasing
the level, it will make the picture smoother).
Color temperature:Y This will increase or
decrease Warm(red) and Cool(blue) colors to
suipersonal preferences. Select Cool to give the
white colors a biue tint, Standard to give the
white colors a neutral tint, Warm to give the
white colors a red tint. User to allow you change
the color manually.
Advanced Video:Y To adjust the picture in
advanced level:
DNR:q Digital Noise Reduction, to adjust
to reduce the appearance of digitizing errror
caused by the compressin: Medium/Strong/
Auto/o/Weak.
Black Level Extender:q To adjust the ability in
the black areas detail of the picture: On or O.
White Peak Limiter: q To adjust the ability in
Operation
EN-13 TV LCD-TFT Owner’s Manual
the white areas detail of the picture: On or O.
CTI: q Color transient intensity, to adjust the picture
for cilor errors: Medium/Strong/o/Weak.
Fiesh Tone: q To adjust the ash colors: On or O.
Adaptive Luma Control: q To adjust changes in the
luminance of the picture On or O.
Audio Menu Options
Sound can be adjusted for any input as follows:
Press
A MENU button and then
/
button until
the following menu appears on the screen.
Audio
Balance
Bass
Treble
Sound Surround On
Mode Off
Equalizer Off
AVL Off
Audio Only
0
50
50
Video
Audio
Channel
Lock
Function
Select
BackAdjust
(;,7
ENTER
/
PressB
/ ENTER button to enter the menu and
/
button to go up and down to select the
desired option.
Press
C
/ ENTER button to conrm and
/
button increase and decrease the level to
adjust the selected option to your preference.
Repeat step 2 and step 3 until desired audio quality
D
has been achieved.
Function
Balance:Y Press
/
button and
/ENTER to
conrm, then press
/
to adjust the audio
output between left and right speakers.
BassY :Press
/
button and
/ENTER button
to conrm, then press
/
to increase or
decrease the level of the lower-pitched sounds.
TrebleY :Press
/
button and
/ENTER
to conrm, then press
/
to increase or
decrease the level of the higher-pitched sounds.
Sound surroundY : To turn the simulated surround
sound on and o.
ModeY : Press
/ENTER button to select the type of
sound which best corresponds to your lightning
requirements by selecting Mode in Audio menu.
EqualizerY : To adjust the equalizer O /Rock /Pop /Live
/Dance/ Techno /Classic/Soft.
AVLY : This will reduces the dierences in volume level
among broadcasters.
Audio OnlyY : Press
/ENTER button to conrm, the
following display will appear on the screen:
Press
to select OK, then press OK to conrm. The TV
screen will be black and no picture , but the sound is
still normal.
If enter Audio Only mode, press POWER to exit!
OK Cancel
You can press POWER button to reveal the picture on
the screen.
SAP Broadcasts Setup
This TV can receive MTS stereo programs and SAP
(Secondary Audio Program) that accompanies the stereo
program; if the station transmits an additional sound
signal as well as the original one.
When having selected SAP button on the remote
control, this TV can only receive the signal when the TV
station transmits the proper signals.
Mono sound is automatically received if the broadcast
is only in Mono; even though Stereo or SAP has been
selected.
Select Mono if you want to listen to mono sound during
stereo/SAP broadcasting.
Stereo or SAP can be received in a Analog channel.
Use the SAP button to select your desired MTS
A
mode in a analog signal. Each time you press the
SAP button, Mono, Stereoor SAP appear. If other
languages are available on the digital signal, select
them with the SAP button.
Press EXIT button to save and return to TV viewing.
B
Channel Menu Options
Channel menu will appear in main menu only in TV
mode.
Press
A MENU button and
/
button until the
following menu appears on the screen.
Operation
TV LCD-TFT Owner’s Manual EN-14
conrm, a mark will be display in the pane as
follows and this channel will be skipped next
time you press
/
button but you can press digits
button to select the channel
. If you want to resume
the channel, press ENTER button again.
Channel Skip
2 Analog
3 Analog
4 Analog
5 Analog
5-1 Digital
6 Analog
7 Analog
8 Analog
9 Analog
10 Analog
Select
Back
EXIT
Set
Video
Audio
Channel
Lock
Function
ENTER
/
Channel LabelY : Allows you to name the channel
that is selected. Press
/ENTER button to enter
the submenu.
Channel Label Set
Channel Index
Channel Label
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
1
/
Then press
/
button to select Channel Index
and
/
button to select the position of the item that
you want to change, afterward press INPUT to input the
numbers and symbols and ENTER button to conrm.
Function Menu Options
Press A MENU button and
/
button until the
following menu appears on the screen.
Function
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
DPMS
Blue Screen On
On
Time Setup
Closed Caption
Default
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
/
PressB
/ ENTER button to enter the menu and
/
Channel
Video
Audio
Channel
Lock
Function
Select
Back
EXIT
Tuner Antenna
Channel Scan
Channel Skip
Channel Label
/
PressB
/ ENTER button to enter the menu and
/
button to go up and down to select the
desired option.
Press
C
/ ENTER button to conrm and
/
button increase and decrease the level to
adjust the selected option to your preference.
Repeat step 2 and step 3 until desired audio quality
D
has been achieved.
Function
TunerY :Press
/ENTER button to select Antenna
or Cable.
Channel ScanY : Press
/ENTER button to start to
scan, press EXIT to cancel.
Channel Scan
Status: Scanning... Antenna
Analog Channels: 4
Digital Channels: 3
Cancel
EXIT
40%
Video
Audio
Channel
Lock
Function
All channels now available will be automatically
preset in order .After the search has nished, the
rst program number will display on the screen. This
search automatically adds only the active channels in
your area to the TV's memory. It deletes any channels
on which there is no broadcast or a poor signal. The
channels found are automatically saved.
Channel SkipY :Press
/ENTER button to enter
the submenu, then press
/
button to select
the channel number (eg.2) and press ENTER to
Operation
EN-15 TV LCD-TFT Owner’s Manual
button to go up and down to select the desired
option.
Press
C
/ ENTER button to conrm and
/
button
increase and decrease the level to adjust the
selected option to your preference.
Repeat step 2 and step 3 until desired quality has
D
been achieved.
Function
LanguageY :Press
/
button to select language of
the OSD.
OSD TimeoutY : Press
/
button to select Middle
/Short and Long to change thetime of the OSD
display.
OSD TransparencyY : Press
/
button to select
among Low/High and Middle to change the
transparency of the OSD. To select Low, the OSD is
opacity.
Screen Mode: Y Press
/
button to select among
Normal/Wide/ Zoom and Cinema to change the
display mode( display mode may dier from dierent
inputs).
Blue Screen: Y Press
/
button to select On, the
screen will be in blue after 3 seconds if there is no
signal.
DPMSY : PC Power Management. To set On, the set
will be in standby mode automatically if no signal
in 2 minutes; if signal input , the set will be on again
automatically.
Time Setup: Y Press
/ ENTER button to enter the
submenu.
Time Zone: q Press
/
button to select the
appropriate time zone.
Time Setup
Time Zone Central
Date/Time
Sleep Timer Off
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
/
Date/Time: q Press
/ ENTER button to enter the
submenu.
Date/Time
Auto On
Date 2009/01/01
Time 11:54 AM
Timer Off
On Time 11:54 AM
Off Time 12:00 AM
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
/
Auto: Press
/
button to select On or O . When
Auto mode on , the time can not be adjusted. Select
O , you can operate to set the time manually.
Date: Press
/
button to select the position and
digits button to set the date.
Time:Press
/
button to select the position and
digits button to set the time.
Timer: Press
/
button to select On or O . To select
O, the time can not be adjusted.
On Time/O Time:Press
/
button to select the
position and digits button to set the time. Press
ENTER button to switch on AM and PM.
Sleep Timer:q Press
/
button to select the
number of minutes: To select O, 5Min, 10Min,15Min,
30Min,45Min,60Min,90Min,120Min,180Min or 240Min.
Closed CaptionY :Press
/ ENTER button to enter the
submenu.
Closed Caption
NTSC Caption Off
DTV Caption Off
DTV Caption Style
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
/
NTSC Captionq : Press
/
button to select
the Closed Caption options. It helps the hearing
impaired with the broadcast program, as well
as helping children learn how to read. A built
in decoder displays the audio portion of a
program as text on the screen when this option
is selected.
CC1: When CC1is displayed on TV means CC
mode is turned on.
CC2 to CC4: For other modes of video related
Operation
TV LCD-TFT Owner’s Manual EN-16
broadcast information.
Text1: For program guide and other information
displayed by broadcasters. (This blocks a large
portion of the picture on your screen).
Text2 to Text4 :For other modes of information
displayed by broadcasters. (This blocks a large
portion of the picture on your screen).
IMPORTANT:Closed captioning availability
entirely depends on broadcasters supplying the
signal. Therefore, closed captioning might not
always be available and language availability will
dier by broadcast.
Select CC1 for full translation of the primary
language such as English in your area. Select
CC2 for secondary language translation such
as French or any other language that may be
broadcast in your area.
DTV Caption:q Press
/
button to select
Service1/Service2/Service3/Service4/Service5/
Service6/O.
DTV Caption Style: q
Press
/ ENTER button to
enter the submenu.
Style: Press
/
button to select one of Default
and Custom. When you select default, the others are
disable and can not be adjusted. When you adjust the
following system,A mark of ABC in a pane will be on
the right of the OSD to display the eect.
Size :Press
/
button to select the size of caption
display according to your own preference.
Text Color: Press
/
button to select the text
color or the opacity of the text box of caption display
according to your own preference.
Select a color and one of the opacity options.
Text Opacity: Press
/
button to specify the
opacity for the text color.
BG Color: Press
/
button to select a
background color.
BG Opacity: Press
/
button to select opacity for
the background color.
Window Color: Press
/
button to select
according your own preference.
Window Opacity: Press
/
button to select the
edge color according your own preference.
Default:Y Press
/ ENTER button to enter the
submenu.
Are you sure?
OK Cancel
Press
/
button to select OK or Cancel, then press
OK to conrm. If OK the parameter will return to the
factory set.
Lock menu
Press A MENU button and
/
button until the
following menu appears on the screen.
Lock
Enter Password
Back
EXIT
Video
Audio
Channel
Lock
Function
PressB
/ ENTER button ato enter and then press
digits button to input the digits( The initial password
is 0000. If you forget your password, you can always
input 9443 to regain control) . The menu will display
as follows:
Lock
Channel Block
Program Block
Password
Clean All
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
Enter
ENTER
/
Channel BlockY :Press
/ ENTER button to enter
DTV Caption Style
Style
Size
Text Color
Text Opacity
BG Color
BG Opacity
Window Color
Window Opacity
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
Custom
Large
White
Solid
Black
Solid
Black
Solid
ABC
/
Operation
EN-17 TV LCD-TFT Owner’s Manual
the submenu as follows.
Channel Lock
10-1 Digital
11 Analog
11-1 Digital
12 Analog
13 Analog
14 Analog
14-1 Digital
14-2 Digital
14-3 Digital
15 Analog
Select
Back
EXIT
Set
Video
Audio
Channel
Lock
Function
WCAU-DT
MBC DTV
ATSC-1
ATSC-2
ATSC-3
ENTER
/
Press
/
button to select the channel you want to
lock, then press ENTER button to conrm. The channel is
locked and a lock mark appears in the pane. If you want
to unlock the channel, repeat the operation above again.
Then press EXIT to exit step by step.
Program Block: Y
/ ENTER button to enter the
submenu as follows.
Program Block
Parental Lock
Parental Guide
MPAA Rating
CA Eng Rating
CA Fren Rating
Block Unrated
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
On
On
/
Parental Lockq : Press
/
button to select On or
O. Used to lock all the system following. To set
O, the system following can not be available.
Parental Guideq : Press
/ ENTER button to
enter the submenu as follows. Press
/
/
/
buttonto select the item you want to lock. Then
press ENTER button to conrm to lock and press
again to resume it. Parental Guide Technology:
The "P.L. Technology" allows you to use U.S. and
Canadian Movies and TV PROGRAMS Guide
ratings to block certain types of TV programs and
movies.
To clearly understand TV program rating codes,
read the following information:
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
A D LSVFV
Allowed Rating Blocked Rating
Parental Guide
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
Set
ENTER
/
U.S. TV Program Ratingsq
TV-Y: For all children - these types of rated programs
are designed for a very young audience, including
children from ages 2-6.
TV-Y7: Directed towards older children - this type of
rated programs may include comedic violence of mild
physical, or may frighten children under the age of 7.
TV-G: General audience-these types of rated programs
contains little or no violence, no strong language, and
little or no sexual dialogue and situations.
TV-PG: Parental Guidance Suggested-this type of
rated programs may contain limited violence, some
suggestive sexual dialogue and situations, and rare
language.
TV-14: Parents strongly cautioned-these types of
rated programs may contain sexual content, strong
language and more intense violence.
TV-MA: Mature audience only these types of rated
programs may contain sexual violence, explicit sexual
content and profane language.
(A)ALL: Blocks all available sub_ratings.
(D)Dialogue: This type of rated programs contain
dialogue with sexual content.
(L)Languag: This type of rated programs contain
oensive language.
(S)Sex: This type of rated programs contain sex.
(V)Violence: This type of rated programs contain
violence.
(FV)Fantasy Violence : This type of rated programs
contain Fantasy and cartoon violence.
MPAA Ratingq
Press
/ ENTER button to enter submenu as follows.
Then press
/
button to select the item you want to
lock. Then press ENTER button to conrm to lock and
press again to resume it.
Allowed Rating Blocked Rating
MPAA Rating
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
Set
G
PG
PG-13
R
NC-17
X
ENTER
/
To understand clearly about movie rating codes, read
Operation
TV LCD-TFT Owner’s Manual EN-18
the following list:
U.S. Movie Rating Chart
G: General Audience-this type of movie rating means
all ages admitted to see the movie.
PG: Parental guidance suggested. Some material may
not be suitable for children.
PG-13: Parents Strongly Cautioned - this type of movie
rating means some material may not be appropriate
for children under13.
R: :Restricted- This type of movie rating means
children under 17 of age require to be with parent or
guardian.
NC-17: This type of movie rating means no one 17 and
under admitted.
X: This type of movie rating means adults only.
CA Eng Ratingq
Press
/ ENTER button to enter submenu as follows.
Press
/
button to select the item you want to lock.
Then press ENTER button to conrm to lock and press
again to resume it.
Allowed Rating Blocked Rating
CA Eng Rating
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
Set
C
C8+
G
PG
14+
18+
ENTER
/
To clearly understand Canadian program rating codes,
read the following list:
Canadian English Rating Chart
C: This type of programming is intended for children
under age 8. There is no oensive language, nudity or
sexual content.
C8+: These type of rated programs are generally
considered acceptable for children 8 years and over.
There is no profanity, nudity or sexual content.
G: These type of rated programs are generally suitable
for all audiences.
PG: Parental Guidance Suggested -in these types of
rated programs, some material may not be suitable for
children.
14+: In these type of rated programs, some content may
not be suitable for viewers under the age of 14.Parents
are strongly cautioned not to have their children view
14+ rated programs by pre-teens and early teens.
18+: Adults Only-these types of rated programs are only
for adult viewers only.
CA Fren Ratingq
Press
/ ENTER button to enter submenu as
follows.
Press
/
button to select the item you want to
lock. Then press ENTER button to conrm to lock
and press again to resume it.
Allowed Rating Blocked Rating
CA Fren Rating
Select
Back
EXIT
Video
Audio
Channel
Lock
Function
Set
G
8 ans+
13
16
18
ans+
ans+
ans+
ENTER
/
Canadian French Rating Chart
G: These types of rated programs are generally suitable
for all audiences.
8 ans+: Children 8 years and above (French)
13 ans+: 13 years old and above(French)
16 ans+: 16 years old and above(French)
18 ans+: Adults Only-these types of rated programs are
only for adult viewers only.
Blocked Unratedq
Press
/
button to select On or O. Used to lock all the
channel not rated.
Password: Press
/ ENTER button to enter the
submenu , press digits button to input the number of 0-9
twice in the New Password and Conrm Password. Then
you
can change the password when you input the same
number twice.
Clean AllY : Press
/ ENTER button to enter the
submenu:
Are you sure?
OK Cancel
Press
/
button to select OK or Cancel then OK to
conrm. If OK, the parameter will return to the factory
set.
Note
If there is any lock mark on the top of the set such R
as channel lock, parental lock and so on, you
can press OK to resume it .( Press OK to display
password menu and input your password.)
PC menu
Operation
EN-19 TV LCD-TFT Owner’s Manual
Press
A MENU button and
/
button to select
Video menu in PC mode.
Press
B
/ ENTER button to enter the Video menu
and
/
button to go up and down to select the
desired option .
Press
C
/ ENTER button to conrm and
/
button to increase and decrease the level to
adjust the selected option to your preference .
Repeat step 2 and step 3 until desired quality has
D
been achieved.
Video
Audio
Lock
Function
Video
Mode Custom
Brightness
Contrast
Color Temperature
PC
50
50
Select
BackAdjust
EXITENTER
/
PCY : Press
/
button to select and
/ ENTER
button to conrm, the PC menu as below:
ENTER
Video
Audio
Lock
Function
PC
Auto Sync
H Position
V Position
Phase
Clock
50
50
Select
BackAdjust
EXIT
50
50
/
Auto Sync: q Press
/
button and then
press
button to adjust that automatically
adjusts the available options for the best viewing
conguration.
H Position: q Press
/
button and then
press
/
button to adjust the horizontal
position of the picture.
V Postion: q Press
/
button and then
press
/
button to adjust the vertical position
of the picture.
Phase:q Press
/
button and then
press
/
button to adjust the phase of the
picture.
Clock: q Press
/
button and then
press
/
button to adjust the clock of the
picture.
USB Input
Supporting media and file format: Digital pictures A
(.JPG) and digital music (.MP3) files
Due to dierences in the file code and file mode, It q
is possible that some files cannot be read.
Before starting operation, verify USB storage device
B
is of FAT32 and FAT file system format. At present,
this television does not support NTFS and the file
systems of other format.
External card reader supports most digital cards
C
available in the market. Readable digital cards are
classified according to the property of card readers
and can be connected to mobile hard disks (working
voltage 5.0V, working current not over 500mA).
The television operation may be halted due to
D
excessive rate of information code errors. In such
case, restart the system. Please note - there are many
nonstandard USB mobile devices in the market. If a
nonstandard device is used then an identification
problem may occur.
To play pictures
Press A USB button on the remote to enter stream
media system.
The system start up takes about 3 seconds. Then q
insert the USB drive in the USB input.
pic1 01/01
Press B
/
button to select Picture folder.
Press ENTER to enter.
P 157.jpg 3264 2448 01/01
pic
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Haier HL19SL2 User manual
-
Haier HLC26R1 Owner's manual
-
-
-
Haier HL42XK1 Operating instructions
-
-
-
-
Haier HL32K1 - K-Series - 32" LCD TV User manual
-
Other documents
-
Hitachi HLC26R1 User manual
-
HCT HLD-32AT User manual
-
Premier TV-4553LED User manual
-
ProScan PLCD5092A-D User manual
-
LG 29FU6RS Owner's manual
-
Engel everLED LE 2460 T2 User manual
-
Initial DTV-262 User manual
-
Philips DVP3050V User guide
-
Nevir NVR-7402-29HD-B User manual
-
Alcatel Temporis 780 User manual
