Delaney BD1061 Owner's manual

Type
Owner's manual
3/4"
1/4"
Wall Spacer (4 or 6)
Floor Guide (1)
Left & Right Stops (2)
Track (1)
Hanger (2)
#8 Floor Screw (2)
¼ Floor Anchor (2)
Hanger Bolt (4 or 6)
for Thicker Doors
Hanger Bolt w/ Cap
(4 or 6)
Anti-Jump Disc (2)
Allen Wrench (1)
5/16 Lag Bolt (4 or 6)
PREPARE THE DOOR
If using the Floor Guide, mortise a groove ¼” wide by ¾”
deep into the bottom center of doors edge.
INSTALL HANGERS
(See back for 2000, 5000, & 6000 Series Drawings)
Position hangers on front center of stile (min. 2” from edge of door,
equal on each side
). Cut a piece of cardboard 2“ high and place
between the inner groove of the wheel and the top of the door to
correctly position the height of the hangers. For 1000, 2000, & 5000
Series, mark holes
& pre-drill 3/8” holes. Secure hangers. For 6000
Series, mark holes & secure hanger using screwdriver (do not drill.)
INSTALL HEADER BOARD
Do NOT install track directly onto drywall. Install a 1x 4
or 1 x 6 Header Board above the door opening directly
into studs. Header board must be solid wood and measure
at least the full legth of the track or longer.
INSTALL STOPS & TRACK
4a. Insert Stops on either side of track, inside the first & last hole.
4b. Position center of the track by measuring up from the floor
(door height + 1 ¾”). Align Spacers with holes in track. Use Lag
Bolts to install track into wood header & wall. Use wrench to
secure screws through spacers.
4
1
3
4a
4b
INCLUDED
COMPONENTS
BARN DOOR HARDWARE KIT
ASSEMBLY INSTRUCTIONS
* Optional Connector Plate available
if connecting multiple tracks.
TOOLS REQUIRED
1/4”
3/8”
* Header Board and
Anchoring Screws not
included in kit.
Center to Stile or
minimum of 2"
2"
2
drill out
3/8"
INSTALLING THE ANTI-JUMP DISCS
Position each anti-jump disc at least 1” from the edge of the
hangers. Tighten slightly to secure in place.
HANG THE DOOR
Place assembled door on secured track. Tighten the anti-jump
discs. Slide door from open to close to ensure all parts are
operating smoothly. Secure stops in desired positions with
allen wrench.
INSTALLING FLOOR DOOR GUIDE (Optional)
Once the door is plumb, place the floor door guide inside
the groove and line up close to the door opening. Slide the
door from open to close to insure working order. Mark
holes with a pencil. Pre-drill ¼” holes. If mounting into a
concrete floor, use provided anchors.
5
6
7
1 3/16"
1/4"
BARN DOOR HARDWARE KIT
ASSEMBLY INSTRUCTIONS
COMPLETED DOOR WITH BARN DOOR KIT
**Note that these instructions depict the installation of
Delaney Hardware 1000 Series Barn Door Kits. While hanger
styles may differ, the same basic instructions will apply.
For questions about installation, please visit
www.delaneyinc.com/barndoorinstructions.asp
Or call (800) 952-4430
Step 2
For the 2000,
5000, and 6000
Series, please refer
to the following
images for Step 2
of the instructions.
  • Page 1 1
  • Page 2 2

Delaney BD1061 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI