Commax DRC-500S Owner's manual

Category
Door intercom systems
Type
Owner's manual

This manual is also suitable for

Contents
1. Greeting. …………………………………………………………………………1
2. Warnings and Notes in safety…………………………………………………2
3. Parts Name ………………………………………………………………………4
4. Features …………………………………………………………………………4
. Descriptions displayed in LCD …………………………………………………6
6. Calling up a residence …………………………………………………………6
7. Calling up a guard station ……………………………………………………7
8. Opening the entrance with PIN ………………………………………………8
9. Opening the entrance with a RFcard ………………………………………8
10. Environment setup(use only for the system administrator) …9
11. Wiring diagram ………………………………………………………………11
12. Product specification …………………………………………………………12
1. Greeing
1
2
Make sure to follow the instructions to prevent any danger or property losses.
Do not put the plug in the socket
simultaneously.
It may generate abnormal heat
or cause a fire.
Do not connect to other products
while in use.
It may cause breakdown.
Do not forcibly bend the cord or
put a heavy object on the
product.
It may cause a fire.
Do not use water, thinner or a
detergent used to wash oil products
when you wash the exterior.
Make sure to wash it by using a dry cloth to
prevent any breakdown or electric shock.
Do not install the product in a
humid place.
It may cause an electric shock or
a fire.
Do not forcibly pull out the
cord from the socket.
If the cord is damaged, it may
cause a fire or an electric shock.
Do not put the plug in the
socket with a wet hand.
It may cause an electric shock.
Do not disassemble, repair or
modify the product.
It may cause a fire, an electric shock
or an injury due to malfunction of the
product.
Do not use AC circuit breaker.
It may cause an electric shock.
2. Warnings and caution
It indicates prohibition.
It indicates prohibition of disassembly.
I
t indicates prohibition of contact.
I
t indicates dos and don’ts.
It indicates that the plug should be pulled out from the socket.
Warning
Death or serious
injury is expected.
3
If the socket holes are larger
than normal, do not put the
plug.
It may cause an electric shock
or a fire.
Make sure that dust or foreign
substances are not gathered
on the product.
Make sure to prevent foreign
substances from entering the
product.
It may cause a breakdown.
Do not put a heavy object on
the product.
It may cause a breakdown.
Do not disassemble or give an
impact to the product.
Avoid direct rays of the sun or
heating devices at a time of
installation.
Install the product in a flat and
stable place.
Otherwise, it may not function
properly.
Pull the plug if the product is
not used for a long time.
If the product generates strange
sound, make sure to pull the
plug immediately and contact
Commax service center.
2. Warnings and caution
It indicates prohibition.
It indicates prohibition of disassembly.
I
t indicates prohibition of contact.
I
t indicates dos and don’ts.
It indicates that the plug should be pulled out from the socket.
Caution
An injury or property
losses are expected
It allows you to open the entrance by
touching RF card on the reader.
b
b
u
u
t
t
t
t
o
o
n
n
:
:
C
C
a
a
l
l
l
l
b
b
u
u
t
t
t
t
o
o
n
n
Press “call” button to run as Enter”on
the computer after registering building
numbers and residents number.
4
8
9
10
11
12
1
2
3
4
5
6
7
13
14
15
3. Part Names
Speaer
Dial Button
Programming button
Electric Key Button
Guard Call button
Cancel Button
Call Button
CCD Camera
Display Screen
LED
RF Card reader
MIC
Connector for hub
Connector for door Loc
DC Power(14V/3A)
4. Features
0
123
456
789
b
b
u
u
t
t
t
t
o
o
n
n
: It is to set the environment.
(use just for administrator)
b
b
u
u
t
t
t
t
o
o
n
n
(When is used as scroll ey:
“down”
directional ey, Numeric Registration Key:
Registration of a decimal point)
: It is to call up guard station.
b
b
u
u
t
t
t
t
o
o
n
n
(When is used as scroll ey: “down”
directional ey, Numeric Registration
Key : Registration of a decimal point)
: It’s to open the entrance with PIN.
b
b
u
u
t
t
t
t
o
o
n
n
: It is to cancel the current operation
or to return initial mode when program
setup is completed.
5
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
6. Calling up a residence
1
1
.
.
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
i
i
o
o
n
n
w
w
i
i
t
t
h
h
r
r
e
e
s
s
i
i
d
d
e
e
n
n
c
c
e
e
s
s
(
(
W
W
h
h
e
e
n
n
b
b
u
u
i
i
l
l
d
d
i
i
n
n
g
g
n
n
u
u
m
m
b
b
e
e
r
r
i
i
s
s
s
s
e
e
t
t
D
D
R
R
C
C
0
0
0
0
S
S
i
i
n
n
a
a
d
d
v
v
a
a
n
n
c
c
e
e
)
)
* Building Number runs automatically, so jut enter residents’numbe
Ex) when you call up resident number,101
Enter resident number 102 and then .
You can hear call sound.
The communication duration last for 60 seconds.
When the communication is completed, press
X" button to end the tal.
When
Door releasebutton is pressed from inhouse unit during the communication,
Door openmessage is displayed on the screen.
2
2
.
.
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
i
i
o
o
n
n
w
w
i
i
t
t
h
h
r
r
e
e
s
s
i
i
d
d
e
e
n
n
c
c
e
e
.
.
(
(
T
T
h
h
e
e
r
r
e
e
i
i
s
s
n
n
t
t
i
i
n
n
p
p
u
u
t
t
v
v
a
a
l
l
u
u
e
e
i
i
n
n
C
C
a
a
l
l
l
l
p
p
r
r
e
e
f
f
i
i
x
x
w
w
h
h
e
e
n
n
b
b
u
u
i
i
l
l
d
d
i
i
n
n
g
g
n
n
u
u
m
m
b
b
e
e
r
r
i
i
s
s
n
n
t
t
s
s
e
e
t
t
D
D
R
R
C
C
0
0
0
0
S
S
i
i
n
n
a
a
d
d
v
v
a
a
n
n
c
c
e
e
)
)
Enter building numbers and then resident number in order.
Ex) when you call up resident number,101 ,building number, 201
I
I
n
n
i
i
t
t
i
i
a
a
l
l
S
S
c
c
r
r
e
e
e
e
n
n
: The state of being registered in a server.
:
The state that only the use of VoIP serve is set but it is not registered in a server.
: Peer to Peer Mode.
:
The state of be able to connect to Local server. (the sever is for use RFID card, PIN)
:
The state that all the information for RF card/PIN was downloaded from DRC00S.
In case of interruptions in server, these bacup data is used for the access of visitors
to the entrance. (Renewal every 12 hours).
6
5. Descriptions displayed in LCD
REG
SIT
P2P
LCS
DAT
Press“”after registering
resident number
Enter resident number
Enter building number 201 and then
And then enter resident number,101 and then
You can hear call sound.
The communication duration last for 60 seconds.
When the communication is completed, press
X" button to end the tal.
When
Door releasebutton is pressed from inhouse unit during the communication,
Door openmessage is displayed on the screen.
If you hear
busysound, press X" button to retry it in a moment.
This is to call up the registered guard stations in advance by a manager Press
“guard callbutton and then .
Maing a call to guard station”message displayed in screen and call sound is
heard
(ringer duration lasts for 30 seconds).
The communication duration lasts for 60 seconds.
When the communication is completed, press
X"
button to end the tal.
When
Door release" button is pressed from inhouse unit during the
communication,
Door open" message is displayed on the screen. If you hear
“busy”sound, press
X" button to retry it.
7
7. Calling up a guard station
Enter resident number
Enter building number
▶▶
Connecting
Guard station
8
9. Opening the entrance with RF card.
It is to open the entrance with RF card registered in advance.
The RF cards should be registered to use in the management station in advance.
Touch RF Card on the reader of it.
The common entrance get be opened with a vocal message, “door opens”when the
access is successful.
The entrance does not be opened when the access fails.
This is to open a common entrance with PIN registered in advance.
The PIN should be a registered in web site for user in the community in advance.
All the process of PIN should be done by web site.
Even the administrator of this system doesn’t now it owing to security program.
The user is responsible for the management of the registered PIN.
And it is optional function to register or use PIN because there is possibility to disclose it.
Enter the residence number only and then‛’
Enter the residence PIN and then “”button.
The common entrance get be opened with vocal message,“door opened”when the
access is successful.
8. Opening the entrance with PIN.
Input Password
10. Environment Setup
(use only for the management)
It is to setup the environment of DRC00S.
Press“PROG”button.
Enter “PIN”with 4 digits long and then ‛’button.
9
D
D
e
e
f
f
a
a
u
u
l
l
t
t
P
P
I
I
N
N
i
i
s
s
0
0
0
0
0
0
0
0
N
N
o
o
t
t
e
e
:
:
P
P
l
l
e
e
a
a
s
s
e
e
m
m
a
a
e
e
s
s
u
u
r
r
e
e
t
t
h
h
a
a
t
t
y
y
o
o
u
u
c
c
h
h
a
a
n
n
g
g
e
e
t
t
h
h
e
e
d
d
e
e
f
f
a
a
u
u
l
l
t
t
P
P
I
I
N
N
i
i
n
n
t
t
o
o
n
n
e
e
w
w
o
o
n
n
e
e
f
f
o
o
r
r
y
y
o
o
u
u
r
r
s
s
e
e
c
c
u
u
r
r
i
i
t
t
y
y
.
.
N
N
o
o
t
t
e
e
:
:
Resetting the system should be done after the completion of the setup
of IP ADDR., NETMASK, GATEWAY, DNS, ENS IP ADDR and UPDATE IP
ADDR respectively.
“•”is used as a Dot(.) to register
IP address in this function.
B
B
u
u
t
t
t
t
o
o
n
n
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
B
B
u
u
t
t
t
t
o
o
n
n
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
0
123
456
789
 Clear
 Up,•
 Down,•
 Cancel
 OK
S
S
e
e
t
t
t
t
i
i
n
n
g
g
M
M
e
e
n
n
u
u
0
0
:
:
H
H
e
e
l
l
p
p
+
+
1
1
:
:
S
S
e
e
t
t
N
N
e
e
t
t
w
w
o
o
r
r
+
+
2
2
:
:
S
S
e
e
t
t
V
V
o
o
i
i
p
p
+
+
3
3
:
:
M
M
a
a
n
n
g
g
e
e
m
m
e
e
n
n
t
t
4
4
:
:
A
A
u
u
d
d
i
i
o
o
/
/
V
V
i
i
d
d
e
e
o
o
+
+
:
:
E
E
x
x
t
t
e
e
a
a
C
C
o
o
n
n
f
f
i
i
g
g
+
+
6
6
:
:
S
S
y
y
s
s
t
t
e
e
m
m
I
I
n
n
f
f
o
o
+
+
7
7
:
:
T
T
e
e
s
s
t
t
+
+
10
0
0
:
:
H
H
e
e
l
l
p
p
+
+
0 : KeyMap (guidance of the use of buttons)
1
1
:
:
S
S
e
e
t
t
N
N
e
e
t
t
w
w
o
o
r
r
+
+
0 : Current Status(the status of current networ setup is displayed)
1 : Static IP+
0 : IP address : (Registration of IP address)
: G/W address (Registration of Gateway)
2 : DNS address (Registration of DNS )
3 : Net mas (Registration of networ mas)
2
2
:
:
S
S
e
e
t
t
V
V
o
o
I
I
P
P
+
+
0 : Use SIP Server (Choice of the availability of using SIP server)
1 : SIP Server (Registration of SIP server address)
2 : Guard ID (Registration of ID of guard station.)
3 : Call Group (availability of using “Call Group”)
3
3
:
:
M
M
a
a
n
n
a
a
g
g
e
e
m
m
e
e
n
n
t
t
+
+
0 : Server address (Registration of local server address)
1 : Update address (Registration of server address for updating)
2 : System ID (Registration of ID of DRC00S)
3 : Call Prefix (Setting a building number)
※ Setup mode to register the building number is displayed automatically in case there
is no input values in a building number.
4
4
:
:
A
A
u
u
d
d
i
i
o
o
/
/
V
V
i
i
d
d
e
e
o
o
+
+
0 : Audio+
0 : Speaer Vol. (adjust speaer volume)
1 : Mic Vol. (adjust mic. Volume)
2 : Key Sound: (the selection of button sound type)
3 : Ring Sound (the selection of Ringer sound type)
4 : Ring Vol. (adjust ringer sound)
1 : Video: +
0 : Quality (adjust the video image quality of visitors)
※ Its video quality gets much better according to the choice one out of
384K/800K/1M/1.2M in order.
B
B
u
u
t
t
L
L
o
o
w
w
l
l
e
e
v
v
e
e
l
l
o
o
u
u
t
t
o
o
f
f
t
t
h
h
e
e
m
m
s
s
h
h
o
o
u
u
l
l
d
d
b
b
e
e
s
s
e
e
l
l
e
e
c
c
t
t
e
e
d
d
a
a
s
s
t
t
h
h
e
e
c
c
a
a
s
s
e
e
m
m
a
a
y
y
b
b
e
e
.
.
:
:
E
E
x
x
t
t
r
r
a
a
C
C
o
o
n
n
f
f
i
i
g
g
+
+
0 : Language (Choice of language)
1 : Set Time+
0 : Door Open Time (Setup the Dooropen duration)
◆ Values from 1 to 2 (unit :Seconds)
1 : Baclight Time ( Setup LCD baclight )
◆ Auto: The baclight turns on in use.
◆ Always: The baclight eep being on.
2 : Key Time Out
◆ Return to the initial mode when there is not other input through button.
11
2 : Change Pwd (change Password)
◆ The old password can be deleted by button.
3 : Auto Ring Off
(Selection of the availability to eep opening the communicating line with residence or a
guard station for certain time after the entrance is opened )
◆ Auto : Cut the communicating line after the entrance is opened.
◆ Manual : Keep opening the communicating after the entrance is opened
Note : The communication should be completed by users in case of “Manual" mode,
4 : Reboot (Reset the system)
 : System Reset ( All the system values become default one)
6
6
:
:
S
S
y
y
s
s
t
t
e
e
m
m
I
I
n
n
f
f
o
o
+
+
0 : Version ( the version of software is displayed)
1 : Memory: (The status of memory is displayed)
2 : Kernel ( information of OS is displayed)
7
7
:
:
T
T
e
e
s
s
t
t
+
+
0 : Test Door Open (It is to test for opening the door)
1 : Test RF Card : (RF card number is displayed)
◆ It is useful to now RF card number.
Touch RF card on the card reader in the status of Reading...
0
123
456
789
11. Wiring Diagram
1
1
.
.
L
L
A
A
N
N
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
(
(
1
1
:
:
1
1
)
)
S
S
t
t
r
r
a
a
i
i
g
g
h
h
t
t
2
2
.
.
D
D
o
o
o
o
r
r
L
L
o
o
c
c
(
(
N
N
O
O
,
,
N
N
C
C
)
)
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
.
.
: COM 2 and COM3 are common wires and N.C1 is for“Normal Close connector" and
N.O4 is for “Normal Open" one.
You can choice the connection according to the entrance type.
3
3
.
.
D
D
C
C
1
1
4
4
V
V
/
/
3
3
A
A
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
.
.
12
Direct connection with UTP CAT.
Please be careful for its polarity.
N.C 1
COM 2
COM 3
N.O 4
12. Specifications
S
S
p
p
e
e
c
c
M
M
o
o
d
d
e
e
l
l
D
D
R
R
C
C
0
0
0
0
S
S
Transmission way
TCP / IP
Related voltage
DC 14V / 3A
Consumption
Max : 1A Standby :0.7A
Communication way
HANDS FREE Type
Display LCD(128 * 64)
Call sound
Electric chime: So, Mi, Do (twice)
Operating 0~+40℃
temperature
513-11, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea
Int’l Business Dept. : Tel.; +82-31-7393-540~550 Fax.; +82-31-745-2133
Web site : www.commax.com
Thank you for purchasing COMMAX products.
Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow
instructions to use a product exactly.
The company is not responsible for any safety accidents caused by abnormal operation of the product.
Printed In Korea / 2010.09.103
Thank you for purchasing COMMAX products.
Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow
instructions to use a product exactly.
The company is not responsible for any safety accidents caused by abnormal operation of the product.
513-11, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea
Int’l Business Dept. : Tel.; +82-31-7393-540~550 Fax.; +82-31-745-2133
Web site : www.commax.com
Thank you for purchasing COMMAX products.
Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow
instructions to use a product exactly.
The company is not responsible for any safety accidents caused by abnormal operation of the product.
COMMAX LOBBY PHONE DRC-500S
User Manual
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Commax DRC-500S Owner's manual

Category
Door intercom systems
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI