Eizo CG247 User manual

Type
User manual
Important
Please read this User’s Manual carefully to familiarize yourself with
safe and effective usage.
The latest software and User’s Manual are available for download
from our web site:
www.eizoglobal.com
Ver. 6.4
2
About This Manual
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior
arrangements are made pursuant to EIZO Corporations receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that specications are subject to change
without notice.
About This Manual
This manual describes the features, installation, and usage of the Color Management Software “ColorNavigator”.
This manual consists of the following four sections.
INSTALLATION Describes software introductory information such as how to install it and how to
connect with the measurement device and the monitor.
P. 5
BASIC Describes basic software operations necessary to adjust the monitor. P. 20
APPLICATION Describes applicable operations such as manual adjustment and prole
emulation. Advanced knowledge regarding color management and computers is
required.
P. 5 2
REFERENCE Provides supplementary explanations and reference information such as
SelfCalibration / SelfCorrection settings and troubleshooting.
P. 85
3
CONTENTS
CONTENTS
About This Manual ................................................ 2
CONTENTS ............................................................. 3
INSTALLATION ............................... 5
Chapter 1 Introduction ....................................... 6
1-1. About ColorNavigator .................................. 6
1-2. About ColorNavigator License .................... 6
How to Check License Registration ................ 6
1-3. Features ......................................................... 7
1-4. Main Window ................................................. 8
About Marks ...................................................10
Chapter 2 Setting Up ........................................ 11
2-1. System Requirements .................................11
2-2. Installing Software .......................................14
Mac .................................................................14
Windows .........................................................17
2-3. Connecting Monitor with Measurement
Device ............................................................19
2-4. Uninstalling Software ..................................19
Mac .................................................................19
Windows .........................................................19
BASIC ........................................... 20
Chapter 3 Starting Up and Quitting ................ 21
3-1. Starting Up ColorNavigator ........................21
Mac .................................................................21
Windows 10 ....................................................21
Windows 8.1 ...................................................21
Windows 7 ..................................................... 22
3-2. Displaying Software Version ..................... 22
3-3. Quitting ColorNavigator ............................. 23
Mac ................................................................ 23
Windows ........................................................ 23
Chapter 4 Adjusting Monitor ........................... 24
4-1. Preparing Adjustment ................................ 24
4-2. Adjusting Monitor ....................................... 25
Chapter 5 Creating Adjustment Target .......... 32
Chapter 6 Periodic Adjustment ....................... 46
6-1. Timer ............................................................. 46
6-2. About SelfCalibration / SelfCorrection .... 46
Chapter 7 Validating Adjustment Status
of Monitor ........................................ 47
APPLICATION ............................... 52
Chapter 8 Setting Monitor Validation ............. 53
8-1. Importing the Validation Target ................ 53
8-2. Deleting Validation Target.......................... 55
Chapter 9 Customizing Adjustment Target ... 56
9-1. Exporting and Importing the Adjustment
Target ............................................................ 56
9-2. SettingaProlePolicy ............................... 57
9-3. Setting Destination Folder for ICC
ProleSaving .............................................. 58
9-4. CreatingProleEmulationData ................ 60
9-5. Manual Adjustment ..................................... 62
9-6. Adjusting Light Booth ................................ 66
Chapter 10
Customizing Monitor Adjustment
... 71
10-1. Setting Measurement Device......................71
10-2. Standard Mode calibration ........................ 72
Chapter 11 Creating Film Emulation Data ....... 73
Chapter12 CreatingICCProleofTablet/
Display Device ................................ 74
12-1. CreatingICCProleofTablet/Display
Device to be Emulated.................................75
12-2. SavingICCProle ........................................81
12-3. Exporting and Importing the
Measurement Result ................................... 82
12-4. Creating Average Value from
Measurement Result ................................... 83
12-5. SettingICCProleCreationProcedure ... 84
12-6. Deleting Measurement Result ................... 84
REFERENCE ................................ 85
Chapter 13 Making Use of the Built-in
Calibration Sensor / Built-in
Correction Sensor .......................... 86
13-1. About Built-in Calibration Sensor / Built-
in Correction Sensor .................................. 86
13-2. Correlate with the Reference
Measurement Device .................................. 86
13-3. Setting the SelfCalibration /
SelfCorrection Schedule ............................ 90
SelfCalibration ................................................91
SelfCorrection ............................................... 92
Chapter 14 Reference ........................................ 93
14-1. Using ColorNavigator in Multiple
Monitor Environment .................................. 93
14-2. Adjusting Monitor with Multiple PCs
Connected .................................................... 94
14-3. Using ColorNavigator Agent ..................... 95
Available Functions ....................................... 95
Active Icon ..................................................... 95
Preventing ColorNavigator to reside ............. 96
Changing Adjusted Target ............................. 96
4
CONTENTS
Starting ColorNavigator .................................97
Monitoring Video Card Gamma .....................97
14-4. Managing Adjusted Targets ....................... 98
Specifying the SelfCalibration /
SelfCorrection target ..................................... 98
Applying Adjusted Target to Monitor ............. 98
Changing Name of Adjustment Target .......... 98
Deleting Adjustment Target ........................... 98
14-5. Setting SelfCalibration / SelfCorrection
Target Automatically .................................. 99
14-6. Checking the Latest Software ..................100
14-7. Displaying Detailed Information
of Adjustment Target / Result and
Validation Record ......................................100
14-8. Other Functions .........................................101
Showing Monitor Information .......................101
Participating in the Quality Improvement
Program ........................................................ 101
Displaying Test Patterns ..............................102
14-9. File Format ..................................................103
LUT File for Gamma Adjustment Target ......103
Validation Target for RGB Type....................103
Validation Target for CMYK Type .................103
Chapter 15 Troubleshooting ............................ 104
15-1. Problems and Remedies ...........................104
15-2. Error Messages ..........................................105
15-3. Universal Access Warning (Mac Only) ....108
15-4. Disabling the Windows Display
Calibration ..................................................109
Windows 10 ................................................. 109
Windows 8.1 and Windows 7 .......................110
15-5. Resolution Warning ................................... 111
About Warning Message .............................. 111
Setting How to Display Resolution
Warning at ColorNavigator Startup .............. 112
15-6. Correlation Warning ..................................113
Setting How to Display Correlation
Warning at Main Window Closure ................ 113
15 -7.
SelfCalibration / SelfCorrection Warning
... 114
Setting Whether to Display Message
SelfCalibration / SelfCorrection Warning
at Main Window Closure ..............................114
15-8. Changing the Settings of the Currently
Used Monitor .............................................115
Chapter 16 Glossary .........................................116
Appendix .............................................................118
Trademark ..............................................................118
5
INSTALLATION
6
Chapter 1 Introduction
Chapter 1 Introduction
1-1. About ColorNavigator
ColorNavigator is a color management software for graphics monitor. It allows you to easily perform accurate
monitor adjustments.
*Please prepare the measurement device and the light booth separately as needed.
1-2. About ColorNavigator License
For some types of monitors, the ColorNavigator license may need to be purchased and registered to the monitor for
use of this software. If the license has not been registered, the software will not start.
For the purchase of the license, contact your local EIZO representative.
How to Check License Registration
The license registration status can be checked using “Monitor Info” screen on the monitor. For details, see the
User’s Manual of the monitor.
If “ColorNavigator License” in the “Monitor Info” screen is “Not Registered”, the ColorNavigator license must
be purchased and registered to the monitor.
The software can be used without purchasing a license on monitors where “ColorNavigator License” is not
displayed in the “Monitor Info” window.
7
Chapter 1 Introduction
1-3. Features
Allows you to adjust the ColorEdge series monitor easily.
• Allows you to specify the target values for the brightness, white point, gamma, and black level of the monitor
precisely.
• L* is available as the target of gamma.
• Displays the measurement result with CIE-chromaticity diagram.
Generates ICC proles of the monitor or tablet / display device based on the measurement result.
Manual adjustment function (white point / brightness / black level / gamma / 6 colors)
Allows you to create an adjustment target based on the paper white or other measurement results.*
1
*1 The function’s availability depends on the measurement device or usage.
Emulation of Monitor Display (not applicable to some monitor types)
- Emulation based on the ICC prole
- Emulation based on the characteristic le (3D-LUT le) of the motion picture lm
Supports built-in calibration sensor / built-in correction sensor*
2
- Sets the target and schedule for SelfCalibration / SelfCorrection.
- Correlates the measurement result from the built-in calibration sensor with the measurement results from
other measurement devices.
*2 This function is available for monitors with a built-in calibration sensor / built-in correction sensor only. For details,
see “Chapter 13 Making Use of the Built-in Calibration Sensor / Built-in Correction Sensor” (page 86).
ICC prole validation
- Validates with RGB / CMYK color patch.
- Outputs validation results.
- Reads RGB / CMYK color patch les.
Switching monitor display
- Switches monitor display based on the monitor adjustment result.
Supporting monitor adjustment function with timer setting
• Supporting a multi monitor environment
Showing test pattern
Adjusting a light booth*
3
*3 About the supported models, see 9-6. Adjusting Light Booth” (page 66).
System-resident function
- Allows you easy access to frequently used functions.
8
Chapter 1 Introduction
1-4. Main Window
Select a function on the main window which is displayed when the software is started.
1
2
4
3 5
6
7
8
9
10
9
Chapter 1 Introduction
The selectable functions on the main window are as follows.
No Menu Overview Sections Reference
1 Target list Lists the adjustment targets.
2 “Create a new
target” button
Allows you to create an
adjustment target.
BASIC “Chapter 5 Creating Adjustment
Target” (page 32)
3 “Delete” button Deletes an adjustment target. REFERENCE “14-4. Managing Adjusted Targets”
(page 98)
4 “Preferences”
button
Opens the “Preferences”
dialog box.
BASIC “6-1. Timer” (page 46)
APPLICATION “Chapter 8 Setting Monitor Validation”
(page 53)
REFERENCE “14-6. Checking the Latest Software”
(page 100)
5 “Detail” button Shows the detailed
information window of
adjustment targets / results
and validation records.
REFERENCE “14-7. Displaying Detailed Information
of Adjustment Target / Result and
Validation Record” (page 100)
6 Adjust” button Allows you to start monitor
adjustment.
BASIC “Chapter 4 Adjusting Monitor” (page 24)
7 Validate” button Allows you to start monitor
validation.
BASIC “Chapter 7 Validating Adjustment
Status of Monitor” (page 47)
8 Advanced” button Provides advanced functions.
Import target Allows you to import the
adjustment target.
APPLICATION “9-1. Exporting and Importing the
Adjustment Target” (page 56)
Export target Allows you to export the
adjustment target.
Adjust
manually
Allows you to adjust the
monitor manually.
APPLICATION “9-5. Manual Adjustment” (page 62)
Create ICC
prole for
tablet/display
device
Allows you to create the ICC
prole of the tablet / display
device.
APPLICATION “Chapter 12 Creating ICC Prole of
Tablet / Display Device” (page 74)
Emulation Allows you to create the emulation data.
ICC Prole Allows you to create the
emulation data of the device.
APPLICATION “9-4. Creating Prole Emulation Data”
(page 60)
Log view
LUT
Allows you to create the
emulation data of the motion
picture lm.
APPLICATION “Chapter 11 Creating Film Emulation
Data” (page 73)
Light booth
adjustment
Allows you to adjust the light
booth.
APPLICATION “9-6. Adjusting Light Booth” (page 66)
Test pattern Shows the test pattern. REFERENCE Displaying Test Patterns” (page 102)
SelfCalibration
/ SelfCorrection
settings
Allows you to set
the SelfCalibration /
SelfCorrection schedule.
REFERENCE “13-3. Setting the SelfCalibration /
SelfCorrection Schedule” (page 90)
Sensor
correlation
Allows you to correlate the
built-in calibration sensor with
the reference measurement
device.
REFERENCE “13-2. Correlate with the Reference
Measurement Device” (page 86)
Standard Mode
calibration
Allows you to update the
monitor gamut.
APPLICATION “10-2. Standard Mode calibration”
(page 72)
Prole policy Shows the policy for creating the prole of each adjustment target.
9 Help Provides the help information.
Users manual Shows the User’s Manual (this document).
Monitor
information
Shows the monitor
information.
REFERENCE Showing Monitor Information” (page 101)
Quality
Improvement
Program
Shows the dialog box for
participating in the Quality
Improvement Program.
REFERENCE Participating in the Quality
Improvement Program” (page 101)
Version Shows the version
information.
BASIC 3-2. Displaying Software Version”
(page 22)
10 Quit Closes the main window.
10
Chapter 1 Introduction
About Marks
The marks in the target list show the status of the target and emulation data.
Mark Monitor Setting Monitor Usage Time after Adjustment
*1
Indicates a target that is applied to the monitor
display.
Within the set time or no setting is made
Indicates a target that is applied to the monitor
display.
Has exceeded the set time
Indicates a target that is not applied to the monitor
display.
Within the set time or no setting is made
Indicates a target that is not applied to the monitor
display.
Has exceeded the set time
Indicates a target that is applied to the monitor
display.
The target is set as a SelfCalibration /
SelfCorrection target.
*2
Within the set time or no setting is made
Indicates a target that is applied to the monitor
display.
The target is set as a SelfCalibration /
SelfCorrection target.
*2
Has exceeded the set time
Indicates a target that is not applied to the monitor
display.
The target is set as a SelfCalibration /
SelfCorrection target.
*2
Within the set time or no setting is made
Indicates a target that is not applied to the monitor
display.
The target is set as a SelfCalibration /
SelfCorrection target.
*2
Has exceeded the set time
Indicates emulation data that is applied to the
monitor display.
-
Indicates emulation data that is not applied to the
monitor display.
-
Blank Unadjusted status. -
*1 The monitor usage time after adjustment is set using the “Timer” (see “6-1. Timer” (page 46)).
*2 For the CG275W / CG245W, the adjustment target set for the monitor is specied as the SelfCalibration target.
is
not attached to the mark.
Emulation data is displayed. For details of
the emulation data, see 9-4. Creating Profile
Emulation Data” (page 60).
11
Chapter 2 Setting Up
Chapter 2 Setting Up
2-1. System Requirements
Computer
Common
Mac or Windows system that satises the Adobe AIR 1.5 system requirements.
• Resolution: recommended resolution of the monitor*
1
USB port: at least 2 free ports required (at least 1 free port for monitors with built-in calibration sensor)*
2
*1 About the recommended resolution of the monitor, see the user’s manual of the monitor.
*2 An EIZO USB cable (MD-C93 or UU200SS) is required to connect the monitor to the computer.
Mac
OS:
- macOS Mojave (10.14)
- macOS High Sierra (10.13)
- macOS Sierra (10.12)
- OS X El Capitan (10.11)
- OS X Yosemite (10.10)
Mac that satises the OS requirement (except iMac (Power PC), iBook, iBook G4)
Memory:
- macOS Mojave (10.14): 2 GB or more
- macOS High Sierra (10.13): 2 GB or more
- macOS Sierra (10.12): 2 GB or more
- OS X El Capitan (10.11): 2 GB or more
- OS X Yosemite (10.10): 2 GB or more
16.7 million or more colors
Windows
OS:
- Windows 10 (32 bit edition and 64 bit edition)
- Windows 8.1 (32 bit edition and 64 bit edition)
- Windows 7 Service Pack 1 (32 bit edition and 64 bit edition)
Memory:
- Windows 10 (64 bit edition): 2 GB or more
- Windows 10 (32 bit edition): 1 GB or more
- Windows 8.1 (64 bit edition): 2 GB or more
- Windows 8.1 (32 bit edition): 1 GB or more
- Windows 7 (64 bit edition): 2 GB or more
- Windows 7 (32 bit edition): 1 GB or more
Colors: 24 bit or more
12
Chapter 2 Setting Up
Monitor
EIZO ColorEdge CG series monitor (except CG18, CG19, CG21, CG3145)
EIZO ColorEdge CX / CS series monitor*
3
*3 For some types of monitors, the ColorNavigator license may need to be registered to the monitor. For details, see “1-
2. About ColorNavigator License” (page 6)
Measurement device*
4,5
X-Rite ColorMunki
*6
X-Rite i1Display / ColorEdge CX1
X-Rite i1Pro / Pro2 / Monitor
*7
X-Rite i1Display 3 / Pro
Datacolor Spyder3 / EX1
Datacolor Spyder4 / EX2
Datacolor Spyder5 / EX3
basICColor DISCUS
*8
Klein K-10 / K-10A
*8
Photo Research PR-655 / PR-680
*8
Konica Minolta CA-210 / CA-310
*9,10
Konica Minolta CS-1000 / CS-1000A
*10
Konica Minolta CS-2000 / CS-2000A
*9,10
Konica Minolta CS-200
*9,10
Colorimetry Research CR-100
*8
Colorimetry Research CR-250
*8
Colorimetry Research CR-300
*8
• JETI specbos 1211
*8
JETI spectraval 1501
*8
Built-in calibration sensor
*11
Light booth*
4,5
JUST ColorCommunicator1
JUST ColorCommunicator2
*4 This product does not contain measurement device or light booth. Please purchase these products separately as
needed.
*5 For details of the system requirements and usage of the measurement device and light booth, see the user’s manual
supplied with the product.
*6 ColorMunki Display and ColorMunki Smile cannot be used.
*7 Whether or not to comply with XRGA can be selected. For details on XRGA, see “Chapter 16 Glossary” (page 116)
*8 When the “Display automatically detected device.” check box is unchecked in the measurement device selection
window (page 28), this is displayed in the list.
*9 Mac is not supported.
*10 The driver is not provided. Contact the manufacturer.
*11 Monitor validation cannot be performed using the built-in calibration sensor of CG2420 / CG2730.
13
Chapter 2 Setting Up
Attention
When the Windows display calibration function is enabled, see 15-4. Disabling the Windows Display Calibration” (page
109) and disable the function.
USB hub may be required if adjusting several monitors in a multiple monitor environment. Also, USB cables are required for
monitor adjustment.
When multiple monitors are connected, each monitor should display an independent screen. Displaying the same screen
on each monitor or across multiple monitors prevents adjustment using the ColorNavigator software. For details of how to
change the settings, see the User’s Manual of the graphics board.
A
B
A
A
A
Independent screen on
each monitor (OK)
Same screen on each
monitor (NG)
A screen over the multiple
monitors (NG)
When using ColorNavigator with a monitor and laptop PC connected, settings for mirroring / duplicating displays must be
disabled in OS settings. Adjustment using ColorNavigator is not possible if identical screens are displayed on the monitor
and laptop PC.
A
B
A
A
Independent screen on the monitor and
laptop PC monitor (OK)
Same screen on the monitor and laptop PC
monitor (NG)
(Mirroring / duplicating)
14
Chapter 2 Setting Up
2-2. Installing Software
Mac
To install the software from the CD-ROM
1.
Insert the “EIZO LCD Utility Disk” to the CD-ROM drive
The “EIZO LCD Utility Disk” icon appears on the desktop. Double-click the icon to open the window.
2.
Double-click “ColorNavigator” folder on the window
3.
Double-click “ColorNavigator 6.pkg” icon on the window
The ColorNavigator installer starts up.
15
Chapter 2 Setting Up
4.
Install the software
Follow the instructions to install the software.
16
Chapter 2 Setting Up
To download and install the software from our website
1.
Double-clickthedownloadedle
The “ColorNavigator 6xx” icon appears on the desktop. Double-click the icon to open the window.
Note
The “ColorNavigator” folder may open automatically depending on your system environment.
2.
Double-click “ColorNavigator 6.pkg” icon on the window
The ColorNavigator installer starts up.
3.
Install the software
Follow the instructions to install the software.
17
Chapter 2 Setting Up
Windows
Attention
A user account with the “Administrator” authority is required.
Please consult your system administrator for your account.
To install the software from the CD-ROM
1.
Insert the “EIZO LCD Utility Disk” to the CD-ROM drive
The menu opens. Click the “Software” tab.
Click “ColorNavigator” - “Install” on the start menu. The ColorNavigator installer starts up.
Note
Double-click the “Launcher.exe” icon if the menu does not open automatically.
The “User Account Control” dialog box may appear when you double-click “Launcher.exe”. Click “Yes” to open the
menu.
2.
Install the software
Follow the instructions to install the software.
18
Chapter 2 Setting Up
To download and install the software from our website
1.
Double-clickthedownloadedle
The ColorNavigator installer starts up.
2.
Install the software
Follow the instructions to install the software.
Attention
The “Windows Security” dialog box may appear several times when you install the software. If this dialog box is displayed,
select “Install this driver software anyway”, and proceed with the installation until the dialog box is no longer displayed.
19
Chapter 2 Setting Up
2-3. Connecting Monitor with Measurement Device
1.
Connect the USB upstream port of monitor and the USB downstream port of
computer with the EIZO USB Cable (MD-C93 or UU200SS)
USBUSB
Attention
When the monitor is equipped with multiple USB upstream ports, use the port that is associated with the input signal to
be displayed. For details, refer to the monitor User’s Manual.
2.
Connect the measurement device to the USB downstream port of the computer
or the monitor
USBUSB
Attention
Some measurement devices may have restrictions on the USB port to connect. For details, see the user’s manual of the
measurement device.
If the measurement device is connected after starting up ColorNavigator, it may not be detected. Be sure to connect the
measurement device before starting up the ColorNavigator.
Note
If your OS is Windows, “Found New Hardware wizard” will appear when you connect the sensor. Please carry out the driver
software installation in accordance with the displayed instructions.
The measurement device driver is automatically installed with ColorNavigator. It is not necessary to install the measurement
device supplied with the device. (For Windows only)
2-4. Uninstalling Software
Mac
1.
Double-click the “/Library/Application Support/EIZO/ColorNavigator/
ColorNavigator 6 Uninstaller” icon.
Windows
Attention
A user account with the “Administrator” authority is required.
Please consult your system administrator for your account.
1.
Select “Control Panel” - “Uninstall a program”
2.
Select “ColorNavigator 6” from the list and click “Uninstall”
20
BASIC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119

Eizo CG247 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI