DFI SD330-H110 User manual

1

SD330-H110

MicroATX Industrial Motherboard

User’s Manual

A40620936

2

Copyright

This publication contains information that is protected by copyright. No part of it may be re-

produced in any form or by any means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions

or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

3

Copyright .............................................................................................................2

Trademarks ........................................................................................................2

FCC and DOC Statement on Class B .....................................................2

Warranty ..............................................................................................................4

Static Electricity Precautions ......................................................................4

Safety Measures ..............................................................................................4

About the Package .........................................................................................5

Optional Items..................................................................................................5

Before Using the System Board ...............................................................5

Chapter 1 - Introduction .............................................................................6

Specifications ................................................................................................6

Features .......................................................................................................... 7

Chapter 2 - Hardware Installation �� 9

Board Layout ................................................................................................. 9

System Memory ............................................................................................ 9

Installing the DIMM Module ........................................................................ 10

CPU ................................................................................................................ 11

Installing the CPU ....................................................................................... 12

Installing the Fan and Heat Sink.................................................................. 14

Jumper Settings ......................................................................................... 15

Clear CMOS Data ........................................................................................ 15

Auto Power-on Select .................................................................................. 15

COM1/COM2 RS232/422/485 Select ............................................................. 16

COM1/COM2 RS232/Power Select ................................................................ 17

Panel Power Select ..................................................................................... 18

LCD/Inverter Power Select .......................................................................... 18

Backlight Power Select ................................................................................ 19

USB Power Select ....................................................................................... 19

Rear Panel I/O Ports ................................................................................. 20

PS/2 Keyboad/Mouse Port ........................................................................... 20

COM (Serial) Ports ...................................................................................... 21

Graphics Interfaces ..................................................................................... 21

RJ45 LAN Ports ........................................................................................... 22

USB Ports ................................................................................................... 22

Audio ......................................................................................................... 23

I/O Connectors ........................................................................................... 24

SATA (Serial ATA) Connectors ...................................................................... 24

Digital I/O Connector .................................................................................. 24

Cooling Fan Connectors............................................................................... 25

Power Connectors ....................................................................................... 25

LVDS LCD Panel Connector ......................................................................... 26

LCD/Inverter Power Connector .................................................................... 26

Chassis Intrusion Connector ........................................................................ 27

Front Panel Connector ................................................................................ 27

Standby Power LED .................................................................................... 28

S/PDIF Connector ....................................................................................... 28

SMBus Connector ....................................................................................... 29

LAN LED Connector .................................................................................... 29

LPC Connector ............................................................................................ 30

Connecting the EXT-RS232/RS485 Card to the Motherboard ......................... 30

Expansion Slots .......................................................................................... 31

Battery ....................................................................................................... 31

Chapter 3 - BIOS Setup �� 32

Overview....................................................................................................... 32

Insyde BIOS Setup Utility (for Intel 6th Generation CPU) ............. 33

Main .......................................................................................................... 33

Advanced ................................................................................................... 33

Security ...................................................................................................... 41

Boot........................................................................................................... 43

Exit ............................................................................................................ 45

Insyde BIOS Setup Utility (for Intel 6/7th Generation CPU) ......... 46

Main .......................................................................................................... 46

Advanced ................................................................................................... 46

Security ...................................................................................................... 57

Boot........................................................................................................... 58

Exit ............................................................................................................ 59

Updating the BIOS .................................................................................... 60

Notice: BIOS SPI ROM ............................................................................. 60

Chapter 4 - Supported Software ........................................................... 61

Appendix A - Troubleshooting Checklist ............................................ 75

Table of Contents

4

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper instal-

lation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in or

out of warranty. It must be returned to the purchase point, factory or authorized service

agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the

product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are

ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts

or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con-

nectors by their ends.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installation or servic-

ing. After installation or servicing, cover the system chassis before plugging the power

cord.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other com-

ponents. Perform the upgrade instruction procedures described at an ESD worksta-

tion only. If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the system chas-

sis. If a wrist strap is unavailable, establish and maintain contact with the system

chassis throughout any procedures requiring ESD protection.

5

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• One SD330-H110 motherboard

• One COM port cable (Length: 300mm, 2 x COM ports)

• One Serial ATA data cable (Length: 500mm)

• One I/O shield

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Optional Items

• USB port cable (Length: 350/398mm)

• COM port cable (Length: 300mm, 2 x COM ports)

• Serial ATA data cable (Length: 500mm)

• Thermal solution (For 35W, Height: 37.3mm)

• Thermal solution (For 65W, Height: 72.8mm)

• LPC EXT-RS232 module (4 x RS232 ports)

• LPC EXT-RS485 module (4 x RS485 ports)

• USB 3.0 port cable (Length: 320mm)

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the following

internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, etc.

You will also need external system peripherals you intend to use which will normally include at

least a keyboard, a mouse and a video display monitor.

6

SYSTEM Processor 7th Generation Intel

®

Core™ Processors, LGA 1151 Socket

Intel

®

Core™ i7-7700 Processor, Quad Core, 8M Cache, 3.6GHz (4.2GHz), 65W

Intel

®

Core™ i7-7700T Processor, Quad Core, 8M Cache, 2.9GHz (3.8GHz), 35W

Intel

®

Core™ i5-7500 Processor, Quad Core, 6M Cache, 3.4GHz (3.8GHz), 65W

Intel

®

Core™ i5-7500T Processor, Quad Core, 6M Cache, 2.7GHz (3.3GHz), 35W

Intel

®

Core™ i3-7101E Processor, Dual Core, 3M Cache, 3.9GHz, 54W

Intel

®

Core™ i3-7101TE Processor, Dual Core, 3M Cache, 3.4GHz, 35W

Intel

®

Celeron

®

Processor G3930E, Dual Core, 2M Cache, 2.9GHz, 54W

Intel

®

Celeron

®

Processor G3930TE, Dual Core, 2M Cache, 2.7GHz, 35W

6th Generation Intel

®

Core™ Processors, LGA 1151 Socket

Intel

®

Core™ i7-6700 Processor, Quad Core, 8M Cache, 3.4GHz (4.0GHz), 65W

Intel

®

Core™ i7-6700TE Processor, Quad Core, 8M Cache, 2.4GHz (3.4GHz), 35W

Intel

®

Core™ i5-6500 Processor, Quad Core, 6M Cache, 3.2GHz (3.6GHz), 65W

Intel

®

Core™ i5-6500TE Processor, Quad Core, 6M Cache, 2.3GHz (3.3GHz), 35W

Intel

®

Core™ i3-6100 Processor, Dual Core, 4M Cache, 3.7GHz, 65W

Intel

®

Core™ i3-6100TE Processor, Dual Core, 4M Cache, 2.7GHz, 35W

Intel

®

Pentium

®

Processor G4400, Dual Core, 3M Cache, 3.3GHz, 65W

Intel

®

Pentium

®

Processor G4400TE, Dual Core, 3M Cache, 2.9GHz, 35W

Intel

®

Celeron

®

Processor G3900, Dual Core, 2M Cache, 2.8GHz, 65W

Intel

®

Celeron

®

Processor G3900TE, Dual Core, 2M Cache, 2.6GHz, 35W

Chipset Intel

®

H110 Chipset

Memory Two 288-pin DIMM up to 32GB

Dual Channel DDR4 1866/2133MHz

BIOS Insyde SPI 128Mbit

GRAPHICS Controller Intel

®

HD Gen 9 Graphics

Feature OpenGL 5.0, DirectX 12, OpenCL 2.1

HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9

HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9

Display 1 x VGA

1 x LVDS

1 x DVI-I (DVI-D signal)

1 x DP++

VGA: resolution up to 1920x1200 @ 60Hz

LVDS: dual channel, resolution up to 1920x1200 @ 60Hz

DVI-I (DVI-D signal): resolution up to 1920x1200 @ 60Hz

DP++: resolution up to 4096x2160 @ 60Hz

Dual

Displays

VGA + LVDS LVDS + DVI-I (DVI-D signal)

VGA + DVI-I (DVI-D signal) LVDS + DP++

VGA + DP++ DVI-I (DVI-D signal) + DP++

EXPANSION Interface 1 x PCIe x16 (Gen 3)

1 x PCIe x4 (Gen 2)

2 x PCI

AUDIO Audio

Codec

Realtek ALC888S-VD2-GR

ETHERNET Controller 1 x Intel

®

I211AT PCIe (10/100/1000Mbps)

1 x Intel

®

I219V PCIe (10/100/1000Mbps)

REAR I/O Ethernet 2 x GbE (RJ-45)

USB 4 x USB 3.0

2 x USB 2.0

Serial 1 x RS-232/422/485 (RS-232 w/ power) (DB-9)

REAR I/O PS/2 1 x PS/2 (mini-DIN-6)

Display 1 x VGA

1 x DVI-I (DVI-D signal)

1 x DP++

Audio 1 x Line-out

1 x Mic-in

1 x Line-in (available upon request)

INTERNAL I/O Serial 1 x RS-232/422/485 (RS-232 w/ power) (2.54mm pitch)

4 x RS-232 (2.54mm pitch)

USB 2 x USB 2.0 (2.54mm pitch)

1 x Vertical USB 2.0 (type A)

Audio 1 x Audio (Line-out/Mic-in) (available upon request)

1 x S/PDIF

SATA 4 x SATA 3.0 (up to 6Gb/s)

DIO 1 x 8-bit DIO

LPC 1 x LPC (supports LPC EXT-RS232/RS485 module)

SMBus 1 x SMBus

Display 1 x LVDS LCD Panel Connector

1 x LCD/Inverter Power

WATCHDOG TIMER Output & Interval System Reset, Programmable via Software from 1 to 255 Seconds

SECURITY TPM Inﬁ neon TPM2.0/1.2 (optional)

POWER Type ATX

Connector 8-pin ATX 12V power

24-pin ATX power

RTC Battery CR2032 Coin Cell

OS SUPPORT Windows 7 (/WES7) 32/64-bit

Windows 8.1 (64-bit)

Windows 10 IoT Enterprise 64-bit

Note: 7th Gen Intel Core processors only support Win 10.

ENVIRONMENT Temperature Operating: 0 to 60°C

Storage: -40 to 85°C

Humidity Operating: 5 to 90% RH

Storage: 5 to 90% RH

MTBF 365,364 hrs @ 25°C; 207,523 hrs @ 45°C; 131,395 hrs @ 60°C

Calculation Model: Telcordia Issue 2, Method Case 3

Environment: GB, GC – Ground Benign, Controlled

MECHANICAL Dimensions microATX form factor

244mm (9.6") x 244mm (9.6")

CERTIFICATIONS CE, FCC Class B, RoHS, UL

Chapter 1 - Introduction

Specifications

7

Features

• Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so

that your system will continue to operate.

• DDR4

DDR4 delivers increased system bandwidth and improves performance. The advantages of

DDR4 provide an extended battery life and improve the performance at a lower power than

DDR3/DDR2.

• Graphics

The integrated Intel

®

HD graphics engine delivers an excellent blend of graphics performance

and features to meet business needs. It provides excellent video and 3D graphics with out-

standing graphics responsiveness. These enhancements deliver the performance and compat-

ibility needed for today’s and tomorrow’s business applications. Supports 1 x VGA, 1 x LVDS, 1

x DVI-I (DVI-D signal) and 1 x DP++ interfaces for display outputs.

• PCI Express

PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds

by forming multiple lanes. The PCI Express architecture also supports high performance graph-

ics infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth.

• Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of

up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel

ATA whose data transfer rate is 100MB/s.

• Gigabit LAN

Two Intel

®

Gigabit LAN controllers (Intel

®

I211AT PCIe and Intel

®

I219V PCIe) support up to

1Gbps data transmission.

• Audio

The Realtek ALC888S-VD2-GR audio codec provides 5.1-channel High Definition audio output.

• Wake-On-PS/2

This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system.

Important:

The 5V_standby power source of your power supply must support ≥720mA.

Important:

The 5V_standby power source of your power supply must support ≥720mA.

• Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a system from the

S3 (STR - Suspend To RAM) state.

• RTC Timer

The RTC installed on the system board allows your system to automatically power-on on the

set date and time.

• ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)

specification. ACPI has energy saving features that enables PCs to implement Power Manage-

ment and Plug-and-Play with operating systems that support OS Direct Power Management.

ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM

function.

With the Suspend to RAM function enabled, you can power-off the system at once by pressing

the power button or selecting “Standby” when you shut down Windows

®

without having to go

through the sometimes tiresome process of closing files, applications and operating system.

This is because the system is capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it powers-off. The operating ses-

sion will resume exactly where you left off the next time you power-on the system.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the

5V_standby power source of your power supply must support ≥1.5A. For 3 or more

USB ports, the 5V_standby power source of your power supply must support ≥2A.

• Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is

supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-

agement Event) signal. However, if your system is in the Suspend mode, you can power-on

the system only through an IRQ or DMA interrupt.

8

• Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

• USB

The system board supports the new USB 3.0. It is capable of running at a maximum transmis-

sion speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)

and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces

power consumption, and is backward compatible with USB 2.0. It is a marked improvement in

device transfer speeds between your computer and a wide range of simultaneously accessible

external Plug and Play peripherals.

www.d.com

9

Chapter 2 Hardware Installation

Chapter 2

Chapter 2 - Hardware Installation

Board Layout

System Memory

DDR4_3

Features

• Two 288-pin DIMM up to 32GB

• Dual Channel DDR4 1866/2133MHz

DVI-I

(DVI-D signal)

DP++

COM 1

VGA

DDR4_1 DDR4_3

1

Clear CMOS

Data (JP1)

1

SATA 0

1

SATA 1

1

SATA 2

1

SATA 3

SATA 3.0

Chassis

Intrusion

1

USB 2.0

1

210

9

USB 7-8

1

2 40

39

LVDS LCD Panel

1

LCD/Inverter Power

Intel

I219V

Intel

I211AT

ASMedia

ASM1442

Chrontel

CH7517A

1

ATX

Power

12 24

13

1 2

11 12

Front

Panel

1 2

LAN LED

7 8

Auto Power-on

Select (JP5)

1

Realtek

ALC888S

1

2

5

6

SMBus

USB 9

14

SPI Flash

BIOS

Line-out

Mic-in

Line-in (opt.)

LAN 1

USB 2

USB 1

USB 3.0

LAN 2

USB 4

USB 3

USB 3.0

PS/2 KB/MS

USB 6

USB 5

USB 2.0

Socket LGA1151

Standby

Power LED

Intel

H110

TPM

(optional)

2 1

1314

LPC

+12V

Power

1

5

4

8

Buzzer

1

210

9

1

210

9 1

210

9 1

210

9 1

210

9

COM 5 COM 6COM 2 COM 3 COM 4

1

2

19

Digital I/O

CPU Fan

1

System Fan 1

1

PCI 1

PCI 2

PCIe 2 (PCIe x4)

PCIe 1 (PCIe x16)

Battery

1

12

56

51

62

51

62

51

62

51

62

51

62

COM 2 RS232/Power

Select (JP14)

1

System

Fan 2

1

2

9

10

Front Audio

(optional)

ITE

IT8893E

COM 2 RS232/422/485 Select (JP12)

COM 2 RS232/422/485 Select (JP13)

COM 2 RS232/422/485 Select (JP11)

COM 1 RS232/422/485

Select (JP8)

COM 1

RS232/422/485

Select (JP10)

COM 1 RS232/Power

Select (JP9)

COM 1

RS232/422/485

Select (JP7)

1

S/PDIF

Backlight Power

Select (JP3)

Panel Power Select (JP2)

NXP

PTN3460

LCD/Inverter

Power Select (JP4)

51

62

51

62

51

62

(JP12)

Nuvoton

NCT6106D

(JP13)

(JP11)

JP31

JP32

SW1

JP36

JP33

JP34

J26

1

ON

2

Standby Power LED

DDR4_1

Vertical USB 2.0 (Type A)

Important:

When the Standby Power LED lights red, it indicates that there is power

on the system board. Power-off the PC then unplug the power cord prior

to installing any devices. Failure to do so will cause severe damage to the

motherboard and components.

Important:

Electrostatic discharge (ESD) can damage your board, processor, disk drives,

add-in boards, and other components. Perform installation procedures at

an ESD workstation only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap and attaching it to

a metal part of the system chassis. If a wrist strap is unavailable, establish

and maintain contact with the system chassis throughout any procedures

requiring ESD protection.

www.d.com

10

Chapter 2 Hardware Installation

Chapter 2

The system board supports the following memory interface.

Single Channel (SC)

Data will be accessed in chunks of 64 bits (8B) from the memory channels.

Dual Channel (DC)

Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides

better system performance because it doubles the data transfer rate.

Single Channel

DIMMs are on the same channel.

DIMMs in a channel can be identical or

completely different. However, we highly

recommend using identical DIMMs.

Not all slots need to be populated.

Dual Channel

DIMMs of the same memory configuration

are on different channels.

Installing the DIMM Module

Note:

The system board used in the following illustrations may not resemble the actual

board. These illustrations are for reference only.

1. Make sure the PC and all other peripheral devices connected to it has been powered down.

2. Disconnect all power cords and cables.

3. Locate the DIMM socket on the system board.

4. Push the “ejector tabs” which are at the ends of the socket to the side.

Ejector tab

5. Note how the module is keyed to the socket.

Key

Notch

www.d.com

11

Chapter 2 Hardware Installation

Chapter 2

CPU

The system board is equipped with a surface mount LGA 1151 socket. This socket is exclu-

sively designed for installing a LGA 1151 packaged Intel CPU.

Protective

cap

Important:

1. Before you proceed, make sure (1) the LGA 1151 socket comes with a protective

cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If

the cap is missing or the cap and/or contact pins are damaged, contact your dealer

immediately.

2. Make sure to keep the protective cap. RMA requests will be accepted and pro-

cessed only if the LGA 1151 socket comes with the protective cap.

Note:

The system board used in the following illustrations may not resemble the actual

board. These illustrations are for reference only.

7. Seat the module vertically, pressing it down firmly until it is completely seated in the

socket.

6. Grasping the module by its edges, position the module above the socket with the “notch”

in the module aligned with the “key” on the socket. The keying mechanism ensures the

module can be plugged into the socket in only one way.

8. The ejector tabs at the ends of the socket will automatically snap into the locked position

to hold the module in place.

www.d.com

12

Chapter 2 Hardware Installation

Chapter 2

Important:

The CPU socket must not come in contact with anything other than the CPU. Avoid

unnecessary exposure. Remove the protective cap only when you are about to install

the CPU.

Installing the CPU

1. Make sure the PC and all other peripheral devices connected to it has been powered down.

2. Disconnect all power cords and cables.

3. Locate the LGA 1151 CPU

socket on the system

board.

4. Unlock the socket by push-

ing the load lever down,

moving it sideways until it

is released from the reten-

tion tab; then lift the load

lever up.

Retention tab

Load lever

6. Remove the protective cap

from the CPU socket. The

cap is used to protect the

CPU socket against dust

and harmful particles.

Remove the protective cap

only when you are about

to install the CPU.

Load lever

Load

plate

5. Lifting the load lever will at

the same time lift the load

plate.

Lift the load lever up to

the angle shown on the

photo.

Protective cap

www.d.com

13

Chapter 2 Hardware Installation

Chapter 2

Important:

The CPU will fit in only one orientation and can easily be inserted without exerting

any force.

7. Insert the CPU into the

socket. The gold triangular

mark on the CPU must

align with the corner of

the CPU socket shown on

the photo.

The CPU’s notch will at

the same time fit into the

socket’s alignment key.

Alignment key

Gold triangular mark

8. Close the load plate then

push the load lever down.

While closing the load

plate, make sure the front

edge of the load plate

slides under the retention

knob.

Retention knob

9. Hook the load lever under

the retention tab.

Load lever

Retention tab

www.d.com

14

Chapter 2 Hardware Installation

Chapter 2

Installing the Fan and Heat Sink

The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circula-

tion across the CPU and heat sink, the CPU will overheat damaging both the CPU and system

board.

1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of the

CPU. The thermal paste is usually supplied when you purchase the fan / heat sink assem-

bly. Do not spread the paste all over the surface. When you later place the heat sink on

top of the CPU, the compound will disperse evenly.

Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal

paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel the

strip that covers the paste before you place the fan / heat sink on top of the CPU.

2. Place the heat sink on top

of the CPU. The 4 screw

around the heat sink,

which are used to secure

the heat sink onto the sys-

tem board, must match the

4 mounting holes around

the socket.

Mounting hole

3. Orient the heat sink such

that the CPU fan’s cable is

nearest the CPU fan con-

nector.

CPU fan connector

4. Rotate each screw that are

diagonally across the heat

sink. Perform the same

procedure for the other

screws.

Heat sink

“Locked” position of

screw

5. Connect the CPU fan’s

cable to the CPU fan

connector on the system

board.

“Unlocked” position

of screw

Note:

A boxed Intel

®

processor already includes the CPU fan and heat sink assembly. If your

CPU was purchased separately, make sure to only use Intel

®

-certified fan and heat

sink.

CPU fan connector

www.d.com

15

Chapter 2 Hardware Installation

Chapter 2

Jumper Settings

Clear CMOS Data

If you encounter the followings,

a) CMOS data becomes corrupted.

b) You forgot the supervisor or user password.

you can reconfigure the system with the default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, please follow the steps below.

1. Power-off the system and unplug the power cord.

2. Set JP1 pins 2 and 3 to On. Wait for a few seconds and set JP1 back to its default setting,

pins 1 and 2 On.

3. Now plug the power cord and power-on the system.

JP1

2-3 On:

Clear CMOS Data

1-2 On:

Normal (default)

31 2

Auto Power-on Select

JP5 is used to select the method of powering on the system. If you want the system to

power-on whenever AC power comes in, set JP5 pin 2 and pin 3 to On. If you want to use the

power button, set pin 1 and pin 2 to On.

When using the JP5 “Power On” feature to power the system back on after a power failure

occurs, the system may not power on if the power lost is resumed within 5 seconds (power

icker).

JP5

2-3 On:

Power-on via AC

power

1-2 On:

Power-on via power

button (default)

31 2

www.d.com

16

Chapter 2 Hardware Installation

Chapter 2

JP7 (COM1)/JP11 (COM2)

COM 1/COM 2

1

2 3 4 5

6 7 8 9

1-2 On:

RS232 (default)

3-4 On:

RS422 Full Duplex

5-6 On:

RS485

2 4 6

1 3 5

2 4

6

1

3 5

2 4 6

1 3 5

2

1

9

Pin RS232 RS422 Full Duplex RS485

1

DCD- RXD+ DATA+

2

RD RXD- DATA-

3

TD TXD+ N.C.

4

DTR- TXD- N.C.

5

GND GND GND

6

DSR- N.C. N.C.

7

RTS- N.C. N.C.

8

CTS- N.C. N.C.

9

RI- N.C. N.C.

JP8/JP10 (COM 1)

1-3, 2-4 On:

RS232 (default)

3-5, 4-6 On:

RS422 Full Duplex

3-5, 4-6 On:

RS485

JP12/JP13 (COM 2)

2 4 6

1

3 5

2 4 6

1

3 5

2 4

6

1 3 5

1-3, 2-4 On:

RS232 (default)

3-5, 4-6 On:

RS422 Full Duplex

3-5, 4-6 On:

RS485

2 4 6

1 3 5

2 4

6

1

3 5

2 4

6

1

3 5

COM1/COM2 RS232/422/485 Select

JP7/JP8/JP10 (for COM 1) and JP11/JP12/JP13 (for COM 2) are used to configure the COM

ports to RS232, RS422 (Full Duplex) or RS485. When COM 1 RS232/422/485 is selected, JP8

and JP10 must be set in accordance to JP7. When COM 2 RS232/422/485 is selected, JP12

and JP13 must be set in accordance to JP11. The pin functions of the COM ports will vary ac-

cording to the jumpers’ setting.

COM 2

COM 1

JP11 (COM 2)

2

1

9

JP7 (COM 1)

JP8

(COM 1)

JP10

(COM 1)

JP12 (COM 2)

JP13 (COM 2)

www.d.com

17

Chapter 2 Hardware Installation

Chapter 2

JP14 (COM 2)

COM1/COM2 RS232/Power Select

COM 2

COM 1

2

1

9

JP9 (COM 1)

JP9 (for COM 1) and JP14 (for COM 2) are used to configure Serial COM ports to pure RS232

or RS232 with power. The pin functions of COM 1 and COM 2 will vary according to JP9’s and

JP14’s setting respectively.

COM 1/COM 2

1

2 3 4 5

6 7 8 9

2

1

9

Pin RS232 RS232 with power

1

DCD- +12V

2

RD RD

3

TD TD

4

DTR- DTR-

5

GND GND

6

DSR- DSR-

7

RTS- RTS-

8

CTS- CTS-

9

RI- +5V

JP9 (COM 1)

1-3 (RI-), 2-4 (DCD-) On:

RS232 (default)

3-5 (+5V), 4-6 (+12V) On:

RS232 with power

JP14 (COM 2)

2 4

6

1

3

5

2 4

6

1

3 5

2

4

6

1

3

5

1

3

5

2

4

6

1-3 (RI-), 2-4 (DCD-) On:

RS232 (default)

3-5 (+5V), 4-6 (+12V) On:

RS232 with power

www.d.com

18

Chapter 2 Hardware Installation

Chapter 2

Panel Power Select

LCD/Inverter Power Select

JP4 is used to select the power level of the LCD/inverter power connector.

2-3 On: +5V

1-2 On: +12V

(default)

31

JP4

JP2

1-2 On: +12V

3-4 On: +5V

5-6 On: +3.3V

(default)

6

1

3

5

2

4

6

1

3

5

2

4

6

1

3

5

2

4

JP2 is used to select the power supplied with the LCD panel.

Important:

Before powering-on the system, make sure that the power settings of JP2 match the

LCD panel’s specification. Selecting the incorrect voltage will seriously damage the

LCD panel.

2

www.d.com

19

Chapter 2 Hardware Installation

Chapter 2

Backlight Power Select USB Power Select

2-3 On: +5V

2-3 On: 5V

3

1

3

2

1-2 On: +3.3V

(default)

1-2 On:

5VDU (default)

3

1

3

JP3

JP31

JP32

JP36

JP34

JP3 is used to select the power level of backlight brightness control: +3.3V (default) or +5V.

The power of the USB connectors’ voltage buses can be configured to either 5VDU or 5V. The

jumpers, i.e. JP31, JP32, JP33, JP34, and JP36 are located as illustrated above and correspond

to each USB port number as listed below.

Important:

Before powering-on the system, make sure that the power settings of JP3 match the

power specification of backlight control. Selecting the incorrect voltage will seriously

damage the backlight.

2

JP33

JP number USB Port

JP31

USB 1/2 (USB 3.0)

JP32

USB 3/4 (USB 3.0)

JP33

USB 5/6 (USB 2.0)

JP34

USB 7/8/9/10 (USB 2.0)

JP36

USB 5/6 (USB 3.0)

www.d.com

20

Chapter 2 Hardware Installation

Chapter 2

Rear Panel I/O Ports

The rear panel I/O ports consist of the following:

• 1 PS/2 Keyboard/Mouse port

• 2 USB 2.0 ports

• 1 Serial COM port

• 1 VGA port

• 1 DVI-I (DVI-D signal) port

• 1 DP++ port

• 2 RJ45 LAN ports

• 4 USB 3.0 ports

• 1 Line-in jack (optional)

• 1 Line-out jack

• 1 Mic-in jack

PS/2 Keyboard/Mouse Port

PS/2 Keyboard/Mouse

VGA

DVI-I

(DVI-D signal)

Line-out

Mic-in

LAN 1

COM 1

DP++

PS/2 KB/MS

USB 3.0

USB 2.0

LAN 2

This rear I/O port is used to connect a PS/2 keyboard/mouse. The PS/2 mouse port uses

IRQ12.

Wake-On-PS/2 Keyboard/Mouse

The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2

mouse to power-on the system. To use this function:

• BIOS Setting

Configure the wake-up function of PS/2 keyboard/mouse in the Advanced menu (“ACPI Con-

figuration” submenu) of the BIOS. Refer to the chapter 3 for more information.

Important:

The +5V_standby power source of your power supply must support ≥720mA.

Page is loading ...

DFI SD330-H110 User manual

DFI SD330-H110 User manual

Related papers

Other documents