3M DBI-SALA® Medium Tape Measure Sleeve 1500099, 1 EA/Case Operating instructions

Type
Operating instructions

3M DBI-SALA® Medium Tape Measure Sleeve 1500099, 1 EA/Case is for fast job site access to tools. The Tape Measure Sleeve conforms to the size of most tape measures. D-Rings on the sides of the Sleeve are load-rated for 5 lbs (2.3kg). The Sleeve has Beacon™ High Visibility Reflectors on the front and back. All warnings, warning labels and instructions should be read and understood before using this product. Never exceed the maximum load rating stated on the Python Safety product label.

3M DBI-SALA® Medium Tape Measure Sleeve 1500099, 1 EA/Case is for fast job site access to tools. The Tape Measure Sleeve conforms to the size of most tape measures. D-Rings on the sides of the Sleeve are load-rated for 5 lbs (2.3kg). The Sleeve has Beacon™ High Visibility Reflectors on the front and back. All warnings, warning labels and instructions should be read and understood before using this product. Never exceed the maximum load rating stated on the Python Safety product label.

Installation and Use Instructions for
Python Safety Pouch Tool Holsters
This manual is intended to be used as part of an employee training program.
These products are not to be used for worker fall protection.
TM
Fall Protection for Tools
TM
© Copyright 2015, DB Industries, Inc.Form: 5903846-A3 Rev: A
www.capitalsafety.com
1
a
c
b
d
d
2
3
4
ee
5
f
EN
Python Tool Holsters
• Beacon™HighVisibilityReectorsonfrontandback.
• TapeMeasureSleeveconformstosizeofmosttapemeasures.
• D-RingsonsidesofSleeveandPouchHolsterareload-ratedfor5lbs
(2.3kg).
• PouchHolsterholdstapemeasureandothersmalltools.
• SafetyRetractorisincludedwith1500098and1500100.Retractorisload-
ratedfor1.5lbs(0.7kg)andextendsupto52in.(132.1cm).
ü
When to use a Tape Measure Sleeve or Tool Holster
• Forfastjobsiteaccesstotools.
û
When NOT to use a Tape Measure Sleeve or Tool Holster
• DonotusetoholstertoolsthatexceedD-Ring or Retractor load
limits.
• WhenuseofaSleeveorHolsterwillinterferewithsafeworking
conditions.
Warnings
• Allwarnings,warninglabelsandinstructionsshouldbereadand
understoodbeforeusingthisproduct.Failuretodosomayresultin
propertydamage,seriousinjuryordeath.
• AllproceduresshowninthisinstructionareforPythonSafetyproducts
only.
• PythonSafetyattachmentpointsrequiretheuseofanappropriate
PythonSafetyLanyard,TetherorRetractorforsafeconnectionof
thetoolorequipmenttoanotherPythonattachmentpoint,theuser
orananchorage.SeespecicPythonSafetyinstructionsforproduct
installation, connection and use procedures.
• Donotuseforworkerfallprotectionorforclimbing.
• Donotuseiffallprotectionfortoolcomponentswillinterferewiththe
safeworkingconditionoroperationoftheconnectedtoolorequipment.
• Ifatoolisdroppedoraloadisforcedontotheconnectionpoint,
inspect the tool and fall protection for tool components
connected to the tool for damage. This includes the attachment
point,thelanyardandtheanchorpoint.(Anchorpointexamples:tool
holster,toolbelt,toolbag,workersafetyharnessoranchorpointsuch
asarail.)Lookfortornstitchingandfordeformitiesanddamagetoany
material.Ifdamageisfound,removetheaffecteditemsfromservice
immediately and replace them.
• Inspectbefore,during,andafterusetoensurefallprotectionfortool
componentsareingoodworkingconditionandfreefromdefects,cuts,
tears,etc.See“InspectBeforeUse”inthisinstructionmanual.Never
modifyPythonSafetyproducts.
• N
everexceedthemaximumloadratingstatedonthe
PythonSafety
product label.
• Neverconnectindividualtoolsthatweighmorethan5pounds(2.26kg)
to a person.
• Neverattachtoollanyardsorattachmentpointstoataperedsurface.
• Neverwrapfallprotectionfortoolcomponentsaroundroughorsharp
edges.
• Neverattachmultiplefallprotectionfortoolcomponentstogether(daisy
chain).
• Nevermakeamodicationtoaconnectedtoolorequipmentthatwill
causeittodeviatefromthemanufacturer’sspecication.
• Alwaysuseproperpersonalprotectiveequipment(PPE).
• Useextremecautionwhileworkingaroundrotatingormoving
equipment.
• Toavoidthedangerofelectricalshock,useextremecautionwhen
workingaroundpowerequipmentandconnections.
• Readandunderstandproductinformationandwarninglabelsforall
connecting lanyards and adapters.
• Allconnectedtoolsandequipmentmustbeproperlymaintainedand
inspectedfordefectsordeteriorationbeforeeachuse.
Inspect Before Use
PythonSafetyequipmentandcomponentsmustbethoroughlyinspected
before,duringandaftereachuse.Anyfallprotectionfortoolscomponent
thathasdeformities,unusualwearordeteriorationmustbeimmediately
removedfromserviceandreplaced.Inspecttheentiresurfaceofthe
component,carefullyrotatingitwhilevisuallyinspectingfordamageorwear
thatmightaffectitsusefulnessanddependability.Inspectmaterialand
stitching,hardware,D-Ringsandfasteners.Conrmthatcarabiners,trigger
snaps, retractors and other connectors operate properly.
How to use the Tape Measure Sleeve (Figure 1):
1.
UnziptheSleeveandinsertthetapemeasureintothesleeve
(a).Makesurethatthetapeendandtapelockareexposedthroughthe
openingsintheSleeve(b).ClosetheSleevezipper(c).
How to use the Tape Measure Retractor Holster
(Figures 2 - 3):
2. Insertuser’sbeltthroughtheRetractorHolsterbeltloops(d).
3.
Attach tape measure to the Retractor connection ring. Clip the tape
measureonHolster.Tapemeasure(ortool)weightmustnotexceed1.5
lbs(0.7kg)whenconnectedtotheRetractor.Toolscanalsobetethered
tothesideD-Rings.Tetheredtoolweightmustnotexceed
5lbs(2.3kg)
whenconnectedtotheD-Rings.
How to use the Pouch Tool Holster with Retractor
(Figures 4 - 5):
4. Insertuser’sbeltthroughthePouchToolHolsterbeltloops(e).
5.
AttachtooltotheRetractorconnectionring(f).Toolweightmustnot
exceed1.5lbs(0.7kg)whenconnectedtotheRetractor.Toolscanalso
betetheredtothesideD-Rings.Tetheredtoolweightmustnotexceed
5
lbs(2.3kg)whenconnectedtotheD-Rings.
After Use
Afteruse,cleantheHolster,Pouchandconnectedtoolorequipmentto
removedirt,corrosivesorcontaminants.Removesurfacedirtwithawipethat
hasbeenmoistenedwithamildsolutionofwaterandsoapordetergent.Work
intoathicklatherandcleantheitem.Wipewithacleanclothandhangtodry
awayfromexcessiveheat,steam,orsunlight.
Storeinacleananddryenvironment,freefromfumesorcorrosiveelements.
Propercareofsafetyequipmenthelpstoensurethatitwilloperateeffectively
andtoextenditsservicelife.
In Case of a Dropped Tool
• Ifatoolisdroppedoraloadisforcedontotheconnectionpoint,
inspect the tool and fall protection for tool components
connected to the tool for damage. This includes the attachment
point,thelanyardandtheanchorpoint.(Anchorpointexamples:tool
holster,toolbelt,toolbag,workersafetyharnessoranchorpointsuch
asarail.)Lookfortornstitchingandfordeformitiesanddamagetoany
material.Ifdamageisfound,removetheaffecteditemsfromservice
immediately and replace them.
• Incidentsshouldbereportedtoyoursafetycoordinator.
1500099
1500095
1500100
1500098
Model #
1500098 Tape Measure Retractor Holster
1500099 Tape Measure Sleeve
1500100
Tape Measure Retractor Holster and
Sleeve Combo, with Retractor
1500095 Pouch Holster with Retractor
www.capitalsafety.com
  • Page 1 1
  • Page 2 2

3M DBI-SALA® Medium Tape Measure Sleeve 1500099, 1 EA/Case Operating instructions

Type
Operating instructions

3M DBI-SALA® Medium Tape Measure Sleeve 1500099, 1 EA/Case is for fast job site access to tools. The Tape Measure Sleeve conforms to the size of most tape measures. D-Rings on the sides of the Sleeve are load-rated for 5 lbs (2.3kg). The Sleeve has Beacon™ High Visibility Reflectors on the front and back. All warnings, warning labels and instructions should be read and understood before using this product. Never exceed the maximum load rating stated on the Python Safety product label.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI