Component Checklist
Coach Screw (x4)
Nylon Anchor (x4)
Washer (x4)
5mm/4mm
Allen Key
M6x16mm
M6x25mm
M8x16mm
M8x25mm
Installation Instructions
TH-3060-UFL
Large-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install Telehook 3060 Large-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
•
5mm (0.2”) drill bit
•
10mm (0.39”) masonry drill bit
•
Phillips head screw driver•
13mm (0.5”) socket wrench or shifter
•
Step 2. Changing position of Arm on Wall Mount
Step 3. Install Arm/Wall Mount to the Wall
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
End Cap (x2)
Top Cap (x2)
Block (x2)
Locking
Screw (x4)
End Cap
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Timber Stud Wall
Masonry Wall
- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Four optional positions
OR
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
WALL WALL
Locking Blocks
Step 4. Attach Top Caps to the installed Arm/Wall Mount
Step 5. Attaching Mounting Brackets to Display
TOP
Back of Display
Display Mounting Screw
Multiwasher
Mounting Bracket
The mounting brackets support
hole configurations from
200x100mm to 700x500mm.
WALL
Pull down both Spring Lock
Ties to open catch.
Hook the Display
to the Arm/Wall
Mount.
1 HOOK
3 PUSH
DOWN
1 HOOK
2 LOCK 4
2 PULL
DOWN
3 PUSH
DOWN
Push down Display into catch. Release Spring Lock Ties
to secure Display.
NOTE: Ensure that Spring
Lock is fully engaged.
RELEASE 4
Step 6. Attaching/Detaching Display to the installed Arm (2 people required)
Top Cap
Top Cap
SLIDE
SLIDE
Step 7. Attach Locking Blocks to fully secure the Display
Back of Display
Back of Display
5mm Allen Key
4mm Allen Key
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 05.06.13 ©
Step 7. Adjust Arm movement if necessary
Step 8. Adjust tilt and roll if necessary
Socket Wrench
LOOSEN
(-kg)
TIGHTEN
(+kg)
-5°
+15°
±5°
WALL
±180°
Position your display to the
desired viewing angle using the
angular movement allowed by
the double ball mount.
Depending on the weight of the
Display, it may be necessary to
make adjustments to the double
ball mount. If the display does
not hold its position, or is too
resistant, adjust the tension
plate located at the rear of the
double ball mount.
To adjust the tension plate, apply
half a turn at a time to each nut.
ENSURE NUTS ARE ADJUSTED
EVENLY.
CHECK THE DISPLAY, and then
adjust again if necessary.
±90°
Step 9. Cable Management
Back of Display
±90°
WALL
/
