PAR64

HQ Power PAR64 User manual

  • Hello! I am an AI chatbot trained to assist you with the HQ Power PAR64 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
VDPLP64SB / VDPLP64SC
27.09.2011 ©Velleman nv
2
User manual
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its
lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted
municipal waste; it should be taken to a specialized company for recycling. This device
should be returned to your distributor or to a local recycling service. Respect the local
environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQ-power! This LED parcan light with high-quality 10mm LEDs gives your
stage or club a unique appearance. It offers you excellent colour mixing through pre-programmed
effects or DMX control. Please read the manual thoroughly before bringing this device into service. If
the device was damaged in transit, do not install or use it and contact your dealer.
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-
threatening electroshocks.
Always disconnect mains power when device not in use or when servicing or
maintenance activities are performed. Handle the power cord by the plug only.
Keep this device away from children and unauthorized users.
Caution: device heats up during use.
Do not stare directly at the light source, as this may cause
- epileptic seizure in sensitive people
- temporarily loss of sight (flash blindness)
- permanent (irreversible) eye damage
There are no user-serviceable parts inside the device. Refer to an authorized
dealer for service and/or spare parts.
This device falls under protection class I. It is therefore essential that the device be earthed. Have
a qualified person carry out the electric connection.
Make sure that the available voltage does not exceed the voltage stated in the specifications of
this manual.
Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it
if necessary.
Respect a minimum distance of 0.5m between the device’s light output and any illuminated
surface.
Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Indoor use only. Keep this device away form rain, moisture, splashing and
dripping liquids.
Keep this device away from dust and extreme heat. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1” (±2.5
cm) in front of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the
device.
Familiarise yourself with the functions of the device before actually using it. Do not allow
operation by unqualified people. Any damage that may occur will most probably be due to
unprofessional use of the device.
All modifications of the device are forbidden for safety reasons. Damage caused by user
modifications to the device is not covered by the warranty.
VDPLP64SB / VDPLP64SC
27.09.2011 ©Velleman nv
3
Only use the device for its intended purpose. All other uses may lead to short circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty
and the dealer will not accept responsibility for any ensuing defects or problems.
Mechanical wear is not covered by the warranty.
A qualified technician should install and service this device.
Do not switch the device on immediately after it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room
temperature.
This device is designed for professional use on stage, in discos, theatres, etc. The
VDPLP64SB/VDPLP64SC can be used indoors with an alternating current of max.
230VAC/50Hz.
Lighting effects are not designed for permanent operation: regular operation breaks will prolong
their lives.
Use the original packaging if the device is to be transported.
Keep this manual for future reference.
4. Features
RGB colour mixing
output distance : 20-25m
master / slave or sound activated
DMX-controlled : 4 channels with dimmer / strobe function
with built-in microphone for sound activation
5. Installation
a) Fixture
Choose a suitable mounting location and mount the light in the desired angle.
Use a waterproof cover when using the light outdoors.
Insert the power cord into an appropriate outlet (230VAC / 50Hz).
Switch off the power to the light when not in use.
This LED parcan is controlled through a 3-pin XLR (1
= GROUND, 2 = DATA-, 3 = DATA+).
b) Fuse
Only fit or replace a fuse when the device is
unplugged from the mains.
Replace a blown fuse with a fuse of the same type
and rating (see “Technical Specifications”):
1. Remove the fuse holder (1) at the back using an
appropriate screwdriver.
2. Remove the old fuse and install a new one.
3. Replace the fuse holder and fasten tight with the
screwdriver.
c) Mounting the Device
Have the device installed by a qualified person, respecting EN 60598-2-17 and all other
applicable norms.
The carrying construction must be able to support 10 times the weight of the device for 1
hour without deforming.
The installation must always be secured with a secondary attachment e.g. a safety cable.
Never stand directly below the device when it is being mounted, removed or serviced. Have a
qualified technician check the device once a year and once before you bring it into service.
Install the device in a location with few passers-by that is inaccessible to unauthorized
persons.
Overhead mounting requires extensive experience: calculating workload limits, determining
the installation material to be used… Have the material and the device itself checked
regularly. Do not attempt to install the device yourself if you lack these qualifications as
improper installation may result in injuries.
Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
Make sure there is no flammable material within a 0.5m radius of the device.
Have a qualified electrician carry out the electric connection.
Connect the device to the mains with the power plug. Do not connect it to a dimming pack.
The installation has to be approved by an expert before the device is taken into service.
VDPLP64SB / VDPLP64SC
27.09.2011 ©Velleman nv
4
6. Use
Auto: DIP switches as below (X means ON, 0 means OFF)
Mode
DIP
Function
10 9 8 7 6 5 4 3 2 1
Auto run
(master
projector)
0 0 X X 0 0 0 0 0 0
Colour changing and fading. Select running
speed via dip 7-8.
0 0 0 0 X X X X X X
Static colour and flash. Select colour via dip
1-3, and flash speed via dip 4-6.
Sound
activated
(master
projector)
0 1 X X X X X X X X Sound-activated colour change.
DMX 1 X X X X X X X X X
DMX mode
CH1 R CH2 G
CH3 B CH4 Dimmer, strobe
Other
1 0 0 0 0 0 0 0 0 1
1. DMX address is 1 when in DMX mode.
2. As slave projector when in M/S mode.
1 0 0 0 0 0 0 0 0 0 Black-out
DMX512 mode:
Press 10 to ON to receive the DMX signal. 1-9 are used to select the requested address.
1 2 3 4 5 6 7 8 9 10
1 2 4 8 16 32 64 128 256 *
Example: If the start address should be 95 the settings would be (for switches 1-10):
1111101000 (1 + 2 + 4 + 8 + 16 + 0 + 64 = 95).
This unit has 4 channels. Refer to the functions below:
Ch 1: 0-255 Red dimmer
Ch 2: 0-255 Green dimmer
Ch 3: 0-255 Blue dimmer
Ch 4: 0-189 Dimmer
190-250 Strobe
251-255 No function
DMX512 Connection
Connect an XLR cable to the female 3-pin XLR output of your controller and the other side to the
male 3-pin XLR input of the VDPLP64SB / VDPLP64SC. Multiple VDPLP64SB / VDPLP64SCs can
be linked through serial linking. The linking cable should be a two-core screened cable with XLR
input and output connectors.
DMX-512 Chain with Termination
A DMX terminator is recommended for installations where the DMX cable has
to run a long distance or is in an electrically noisy environment (e.g. discos).
The terminator prevents corruption of the digital control signal by electrical
noise. The DMX terminator is simply an XLR plug with a 120 resistor
between pins 2 and 3, which is then plugged into the XLR output socket of
the last device in the chain.
Please see illustrations.
Projector DMX start address selection
All DMX-controlled devices need a digital start address so that the correct device responds to the
signals. This start address is the channel number from which the device starts to “listen” to the DMX
controller. Enter the correct number and read it from the display located on the base of the
VDPLP64SB / VDPLP64SC.
You can use the same starting address for a whole group of devices or enter an individual one for
every device.
When all devices have the same address, all the VDPLP64SB / VDPLP64SCs will “listen” to the
control signal on one particular channel. In other words: changing the settings of one channel will
affect all devices simultaneously. If you set different addresses, each device will “listen” to a
separate channel number. Changing the settings of one channel will only affect the device in
question.
In the case of the 4-channel VDPLP64SB / VDPLP64SC, you will have to set the start address of
the first VDPLP64SB / VDPLP64SC to 1, the second VDPLP64SB / VDPLP64SC to 5 (1 + 4), the
third to 9 (5 + 4) and so on.
VDPLP64SB / VDPLP64SC
27.09.2011 ©Velleman nv
5
7. Cleaning and maintenance
1. All screws should be tight and free of corrosion.
2. The housing, the lenses, the mounting supports and the installation location (e.g. ceiling,
suspension, trussing) should not be deformed, modified or tampered with e.g. do not drill extra
holes in mounting supports, do not change the location of the connections …
3. Mechanically moving parts must not show any signs of wear and tear.
4. The electric power supply cables must not show any damage. Have a qualified technician
maintain the device.
5. Disconnect the device from the mains prior to maintenance activities.
6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
7. There are no user-serviceable parts apart from the fuse (see “Installation”).
8. Contact your dealer for spare parts if necessary.
8. Technical specifications
Power Supply max. 230VAC / 50Hz
Power Consumption max. 30W
Fuse 0.5A, 250VAC (5 x 20mm) (order code FF0.5N)
LEDs 183 pcs (red x 60, green x 60, blue x 60)
LED diameter Ø 10mm
DMX512 Connection 3-pin XLR socket
Dimensions 300 x 220 x 230mm
Total Weight 2.3kg
Max. Ambient Temperature 45°C
Max. Housing Temperature 80°C
Use this device with original accessories only. Velleman nv cannot be held responsible in
the event of damage or injury resulted from (incorrect) use of this device.
For more info concerning this product, please visit our website www.hqpower.eu.
The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.
No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or
otherwise without the prior written consent of the copyright holder.
GEBRUIKERSHANDLEIDING
1. Inleiding
Aan alle ingezetenen van de Europese Unie
Belangrijke milieu-informatie betreffende dit product
Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt
weggeworpen, dit toestel schade kan toebrengen aan het milieu. Gooi dit toestel (en
eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een
gespecialiseerd bedrijf terechtkomen voor recyclage. U moet dit toestel naar uw verdeler of
naar een lokaal recyclagepunt brengen. Respecteer de plaatselijke milieuwetgeving.
Hebt u vragen, contacteer dan de plaatselijke autoriteiten betreffende de verwijdering.
Dank u voor uw aankoop! De VDPLP64SB / VDPLP64SC is een parcan led-projector met
hoogwaardige 10mm led’s waarmee u een podium of club op een originele manier kunt verlichten.
De VDPLP64SB / VDPLP64SC biedt een kleurmenging via voorgeprogrammeerde effecten of DMX-
besturing. Lees deze handleiding grondig voor u het toestel in gebruik neemt. Werd het toestel
beschadigd tijdens het transport, installeer het dan niet en raadpleeg uw dealer.
2. Veiligheidsinstructies
Wees voorzichtig bij de installatie: raak geen kabels aan die onder stroom
staan om dodelijke elektroshocks te vermijden.
Trek de stekker uit het stopcontact (trek niet aan de kabel!) voordat u het
toestel reinigt en als u het niet gebruikt.
Velleman® Service and Quality Warranty
Velleman® has over 35 years of experience in the electronics
world and distributes its products in more than 85 countries.
All our products fulfil strict quality requirements and legal
stipulations in the EU. In order to ensure the quality, our products
regularly go through an extra quality check, both by an internal
quality department and by specialized external organisations. If, all
precautionary measures notwithstanding, problems should occur,
please make appeal to our warranty (see guarantee conditions).
General Warranty Conditions Concerning Consumer
Products (for EU):
• All consumer products are subject to a 24-month warranty on
production flaws and defective material as from the original date of
purchase.
• Velleman® can decide to replace an article with an equivalent
article, or to refund the retail value totally or partially when the
complaint is valid and a free repair or replacement of the article is
impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of
100% of the purchase price in case of a flaw occurred in the first
year after the date of purchase and delivery, or a replacing article
at 50% of the purchase price or a refund at the value of 50% of
the retail value in case of a flaw occurred in the second year after
the date of purchase and delivery.
• Not covered by warranty:
- all direct or indirect damage caused after delivery to the article
(e.g. by oxidation, shocks, falls, dust, dirt, humidity...), and by the
article, as well as its contents (e.g. data loss), compensation for
loss of profits;
- frequently replaced consumable goods, parts or accessories such
as batteries, lamps, rubber parts, drive belts... (unlimited list);
- flaws resulting from fire, water damage, lightning, accident,
natural disaster, etc. …;
- flaws caused deliberately, negligently or resulting from improper
handling, negligent maintenance, abusive use or use contrary to
the manufacturer’s instructions;
- damage caused by a commercial, professional or collective use of
the article (the warranty validity will be reduced to six (6) months
when the article is used professionally);
- damage resulting from an inappropriate packing and shipping of
the article;
- all damage caused by modification, repair or alteration performed
by a third party without written permission by Velleman®.
• Articles to be repaired must be delivered to your Velleman®
dealer, solidly packed (preferably in the original packaging), and
be completed with the original receipt of purchase and a clear flaw
description.
• Hint: In order to save on cost and time, please reread the
manual and check if the flaw is caused by obvious causes prior to
presenting the article for repair. Note that returning a non-
defective article can also involve handling costs.
• Repairs occurring after warranty expiration are subject to
shipping costs.
• The above conditions are without prejudice to all commercial
warranties.
The above enumeration is subject to modification according
to the article (see article’s manual).
Velleman® service- en kwaliteitsgarantie
Velleman® heeft ruim 35 jaar ervaring in de elektronicawereld en
verdeelt in meer dan 85 landen.
Al onze producten beantwoorden aan strikte kwaliteitseisen en aan
de wettelijke bepalingen geldig in de EU. Om de kwaliteit te
waarborgen,
ondergaan onze producten op regelmatige tijdstippen een extra
kwaliteitscontrole, zowel door onze eigen kwaliteitsafdeling als
door externe gespecialiseerde organisaties. Mocht er ondanks deze
voorzorgen toch een probleem optreden, dan kunt u steeds een
beroep doen op onze waarborg (zie waarborgvoorwaarden).
Algemene waarborgvoorwaarden consumentengoederen
(voor Europese Unie):
• Op alle consumentengoederen geldt een garantieperiode van 24
maanden op productie- en materiaalfouten en dit vanaf de
oorspronkelijke aankoopdatum.
• Indien de klacht gegrond is en een gratis reparatie of vervanging
van een artikel onmogelijk is of indien de kosten hiervoor buiten
verhouding zijn, kan Velleman® beslissen het desbetreffende
artikel te vervangen door een gelijkwaardig artikel of de
aankoopsom van het artikel gedeeltelijk of volledig terug te
betalen. In dat geval krijgt u een vervangend product of
terugbetaling ter waarde van 100% van de aankoopsom bij
ontdekking van een gebrek tot één jaar na aankoop en levering, of
een vervangend product tegen 50% van de kostprijs of
terugbetaling van 50 % bij ontdekking na één jaar tot 2 jaar.
• Valt niet onder waarborg:
- alle rechtstreekse of onrechtstreekse schade na de levering
veroorzaakt aan het toestel (bv. door oxidatie, schokken, val, stof,
vuil, vocht...), en door het toestel, alsook zijn inhoud (bv. verlies
van data), vergoeding voor eventuele winstderving.
- verbruiksgoederen, onderdelen of hulpstukken die regelmatig
dienen te worden vervangen, zoals bv. batterijen, lampen,
rubberen onderdelen, aandrijfriemen... (onbeperkte lijst).
- defecten ten gevolge van brand, waterschade, bliksem,
ongevallen, natuurrampen, enz.
- defecten veroorzaakt door opzet, nalatigheid of door een
onoordeelkundige behandeling, slecht onderhoud of abnormaal
gebruik of gebruik van het toestel strijdig met de voorschriften van
de fabrikant.
- schade ten gevolge van een commercieel, professioneel of
collectief gebruik van het apparaat (bij professioneel gebruik wordt
de garantieperiode herleid tot 6 maand).
- schade veroorzaakt door onvoldoende bescherming bij transport
van het apparaat.
- alle schade door wijzigingen, reparaties of modificaties
uitgevoerd door derden zonder toestemming van Velleman®.
• Toestellen dienen ter reparatie aangeboden te worden bij uw
Velleman®-verdeler. Het toestel dient vergezeld te zijn van het
oorspronkelijke aankoopbewijs. Zorg voor een degelijke verpakking
(bij voorkeur de originele verpakking) en voeg een duidelijke
foutomschrijving bij.
• Tip: alvorens het toestel voor reparatie aan te bieden, kijk nog
eens na of er geen voor de hand liggende reden is waarom het
toestel niet naar behoren werkt (zie handleiding). Op deze wijze
kunt u kosten en tijd besparen. Denk eraan dat er ook voor niet-
defecte toestellen een kost voor controle aangerekend kan worden.
• Bij reparaties buiten de waarborgperiode zullen transportkosten
aangerekend worden.
• Elke commerciële garantie laat deze rechten onverminderd.
Bovenstaande opsomming kan eventueel aangepast worden
naargelang de aard van het product (zie handleiding van het
betreffende product).
Garantie de service et de qualité Vellema
Velleman® jouit d’une expérience de plus de 35 ans dans le
monde de l’électronique avec une distribution dans plus de 85
pays.
Tous nos produits répondent à des exigences de qualité
rigoureuses et à des dispositions légales en vigueur dans l’UE. Afin
de garantir la qualité, nous soumettons régulièrement nos produits
à des contrôles de qualité supplémentaires, tant par notre propre
service qualité que par un service qualité externe. Dans le cas
improbable d’un défaut malgré toutes les précautions, il est
possible d’invoquer notre garantie (voir les conditions de garantie).
Conditions générales concernant la garantie sur les produits
grand public (pour l’UE) :
• tout produit grand public est garanti 24 mois contre tout vice de
production ou de matériaux à dater du jour d’acquisition effective ;
• si la plainte est justifiée et que la réparation ou le remplacement
d’un article est jugé impossible, ou lorsque les coûts s’avèrent
disproportionnés, Velleman® s’autorise à remplacer ledit article
par un article équivalent ou à rembourser la totalité ou une partie
du prix d’achat. Le cas échéant, il vous sera consenti un article de
remplacement ou le remboursement complet du prix d’achat lors
d’un défaut dans un délai de 1 an après l’achat et la livraison, ou
un article de remplacement moyennant 50% du prix d’achat ou le
remboursement de 50% du prix d’achat lors d’un défaut après 1 à
2 ans.
• sont par conséquent exclus :
- tout dommage direct ou indirect survenu à l’article après livraison
(p.ex. dommage lié à l’oxydation, choc, chute, poussière, sable,
impureté…) et provoqué par l’appareil, ainsi que son contenu
(p.ex. perte de données) et une indemnisation éventuelle pour
perte de revenus ;
- tout bien de consommation ou accessoire, ou pièce qui nécessite
un remplacement régulier comme p.ex. piles, ampoules, pièces en
caoutchouc, courroies… (liste illimitée) ;
- tout dommage qui résulte d’un incendie, de la foudre, d’un
accident, d’une catastrophe naturelle, etc. ;
/