HQ Power PAR64 User manual

Page is loading ...

VDPLP64SB / VDPLP64SC

27.09.2011 ©Velleman nv

2

User manual

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its

lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted

municipal waste; it should be taken to a specialized company for recycling. This device

should be returned to your distributor or to a local recycling service. Respect the local

environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing HQ-power! This LED parcan light with high-quality 10mm LEDs gives your

stage or club a unique appearance. It offers you excellent colour mixing through pre-programmed

effects or DMX control. Please read the manual thoroughly before bringing this device into service. If

the device was damaged in transit, do not install or use it and contact your dealer.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-

threatening electroshocks.

Always disconnect mains power when device not in use or when servicing or

maintenance activities are performed. Handle the power cord by the plug only.

Keep this device away from children and unauthorized users.

Caution: device heats up during use.

Do not stare directly at the light source, as this may cause

- epileptic seizure in sensitive people

- temporarily loss of sight (flash blindness)

- permanent (irreversible) eye damage

There are no user-serviceable parts inside the device. Refer to an authorized

dealer for service and/or spare parts.

• This device falls under protection class I. It is therefore essential that the device be earthed. Have

a qualified person carry out the electric connection.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of

this manual.

• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it

if necessary.

• Respect a minimum distance of 0.5m between the device’s light output and any illuminated

surface.

• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Indoor use only. Keep this device away form rain, moisture, splashing and

dripping liquids.

Keep this device away from dust and extreme heat. Make sure the ventilation

openings are clear at all times. For sufficient air circulation, leave at least 1” (±2.5

cm) in front of the openings.

Protect this device from shocks and abuse. Avoid brute force when operating the

device.

• Familiarise yourself with the functions of the device before actually using it. Do not allow

operation by unqualified people. Any damage that may occur will most probably be due to

unprofessional use of the device.

• All modifications of the device are forbidden for safety reasons. Damage caused by user

modifications to the device is not covered by the warranty.

VDPLP64SB / VDPLP64SC

27.09.2011 ©Velleman nv

3

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns,

electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the

warranty.

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty

and the dealer will not accept responsibility for any ensuing defects or problems.

• Mechanical wear is not covered by the warranty.

• A qualified technician should install and service this device.

• Do not switch the device on immediately after it has been exposed to changes in temperature.

Protect the device against damage by leaving it switched off until it has reached room

temperature.

• This device is designed for professional use on stage, in discos, theatres, etc. The

VDPLP64SB/VDPLP64SC can be used indoors with an alternating current of max.

230VAC/50Hz.

• Lighting effects are not designed for permanent operation: regular operation breaks will prolong

their lives.

• Use the original packaging if the device is to be transported.

• Keep this manual for future reference.

4. Features

• RGB colour mixing

• output distance : 20-25m

• master / slave or sound activated

• DMX-controlled : 4 channels with dimmer / strobe function

• with built-in microphone for sound activation

5. Installation

a) Fixture

• Choose a suitable mounting location and mount the light in the desired angle.

• Use a waterproof cover when using the light outdoors.

• Insert the power cord into an appropriate outlet (230VAC / 50Hz).

• Switch off the power to the light when not in use.

• This LED parcan is controlled through a 3-pin XLR (1

= GROUND, 2 = DATA-, 3 = DATA+).

b) Fuse

• Only fit or replace a fuse when the device is

unplugged from the mains.

• Replace a blown fuse with a fuse of the same type

and rating (see “Technical Specifications”):

1. Remove the fuse holder (1) at the back using an

appropriate screwdriver.

2. Remove the old fuse and install a new one.

3. Replace the fuse holder and fasten tight with the

screwdriver.

c) Mounting the Device

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other

applicable norms.

• The carrying construction must be able to support 10 times the weight of the device for 1

hour without deforming.

• The installation must always be secured with a secondary attachment e.g. a safety cable.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a

qualified technician check the device once a year and once before you bring it into service.

• Install the device in a location with few passers-by that is inaccessible to unauthorized

persons.

• Overhead mounting requires extensive experience: calculating workload limits, determining

the installation material to be used… Have the material and the device itself checked

regularly. Do not attempt to install the device yourself if you lack these qualifications as

improper installation may result in injuries.

• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.

• Make sure there is no flammable material within a 0.5m radius of the device.

• Have a qualified electrician carry out the electric connection.

• Connect the device to the mains with the power plug. Do not connect it to a dimming pack.

• The installation has to be approved by an expert before the device is taken into service.

VDPLP64SB / VDPLP64SC

27.09.2011 ©Velleman nv

4

6. Use

• Auto: DIP switches as below (X means ON, 0 means OFF)

Mode

DIP

Function

10 9 8 7 6 5 4 3 2 1

Auto run

(master

projector)

0 0 X X 0 0 0 0 0 0

Colour changing and fading. Select running

speed via dip 7-8.

0 0 0 0 X X X X X X

Static colour and flash. Select colour via dip

1-3, and flash speed via dip 4-6.

Sound

activated

(master

projector)

0 1 X X X X X X X X Sound-activated colour change.

DMX 1 X X X X X X X X X

DMX mode

CH1 → R CH2 → G

CH3 → B CH4 → Dimmer, strobe

Other

1 0 0 0 0 0 0 0 0 1

1. DMX address is 1 when in DMX mode.

2. As slave projector when in M/S mode.

1 0 0 0 0 0 0 0 0 0 Black-out

• DMX512 mode:

Press 10 to ON to receive the DMX signal. 1-9 are used to select the requested address.

1 2 3 4 5 6 7 8 9 10

1 2 4 8 16 32 64 128 256 *

Example: If the start address should be 95 the settings would be (for switches 1-10):

1111101000 (1 + 2 + 4 + 8 + 16 + 0 + 64 = 95).

This unit has 4 channels. Refer to the functions below:

Ch 1: 0-255 Red dimmer

Ch 2: 0-255 Green dimmer

Ch 3: 0-255 Blue dimmer

Ch 4: 0-189 Dimmer

190-250 Strobe

251-255 No function

• DMX512 Connection

Connect an XLR cable to the female 3-pin XLR output of your controller and the other side to the

male 3-pin XLR input of the VDPLP64SB / VDPLP64SC. Multiple VDPLP64SB / VDPLP64SCs can

be linked through serial linking. The linking cable should be a two-core screened cable with XLR

input and output connectors.

• DMX-512 Chain with Termination

A DMX terminator is recommended for installations where the DMX cable has

to run a long distance or is in an electrically noisy environment (e.g. discos).

The terminator prevents corruption of the digital control signal by electrical

noise. The DMX terminator is simply an XLR plug with a 120Ω resistor

between pins 2 and 3, which is then plugged into the XLR output socket of

the last device in the chain.

Please see illustrations.

• Projector DMX start address selection

All DMX-controlled devices need a digital start address so that the correct device responds to the

signals. This start address is the channel number from which the device starts to “listen” to the DMX

controller. Enter the correct number and read it from the display located on the base of the

VDPLP64SB / VDPLP64SC.

You can use the same starting address for a whole group of devices or enter an individual one for

every device.

When all devices have the same address, all the VDPLP64SB / VDPLP64SCs will “listen” to the

control signal on one particular channel. In other words: changing the settings of one channel will

affect all devices simultaneously. If you set different addresses, each device will “listen” to a

separate channel number. Changing the settings of one channel will only affect the device in

question.

In the case of the 4-channel VDPLP64SB / VDPLP64SC, you will have to set the start address of

the first VDPLP64SB / VDPLP64SC to 1, the second VDPLP64SB / VDPLP64SC to 5 (1 + 4), the

third to 9 (5 + 4) and so on.

VDPLP64SB / VDPLP64SC

27.09.2011 ©Velleman nv

5

7. Cleaning and maintenance

1. All screws should be tight and free of corrosion.

2. The housing, the lenses, the mounting supports and the installation location (e.g. ceiling,

suspension, trussing) should not be deformed, modified or tampered with e.g. do not drill extra

holes in mounting supports, do not change the location of the connections …

3. Mechanically moving parts must not show any signs of wear and tear.

4. The electric power supply cables must not show any damage. Have a qualified technician

maintain the device.

5. Disconnect the device from the mains prior to maintenance activities.

6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

7. There are no user-serviceable parts apart from the fuse (see “Installation”).

8. Contact your dealer for spare parts if necessary.

8. Technical specifications

Power Supply max. 230VAC / 50Hz

Power Consumption max. 30W

Fuse 0.5A, 250VAC (5 x 20mm) (order code FF0.5N)

LEDs 183 pcs (red x 60, green x 60, blue x 60)

LED diameter Ø 10mm

DMX512 Connection 3-pin XLR socket

Dimensions 300 x 220 x 230mm

Total Weight 2.3kg

Max. Ambient Temperature 45°C

Max. Housing Temperature 80°C

Use this device with original accessories only. Velleman nv cannot be held responsible in

the event of damage or injury resulted from (incorrect) use of this device.

For more info concerning this product, please visit our website www.hqpower.eu.

The information in this manual is subject to change without prior notice.

The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.

No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or

otherwise without the prior written consent of the copyright holder.

GEBRUIKERSHANDLEIDING

1. Inleiding

Aan alle ingezetenen van de Europese Unie

Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt

weggeworpen, dit toestel schade kan toebrengen aan het milieu. Gooi dit toestel (en

eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een

gespecialiseerd bedrijf terechtkomen voor recyclage. U moet dit toestel naar uw verdeler of

naar een lokaal recyclagepunt brengen. Respecteer de plaatselijke milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke autoriteiten betreffende de verwijdering.

Dank u voor uw aankoop! De VDPLP64SB / VDPLP64SC is een parcan led-projector met

hoogwaardige 10mm led’s waarmee u een podium of club op een originele manier kunt verlichten.

De VDPLP64SB / VDPLP64SC biedt een kleurmenging via voorgeprogrammeerde effecten of DMX-

besturing. Lees deze handleiding grondig voor u het toestel in gebruik neemt. Werd het toestel

beschadigd tijdens het transport, installeer het dan niet en raadpleeg uw dealer.

2. Veiligheidsinstructies

Wees voorzichtig bij de installatie: raak geen kabels aan die onder stroom

staan om dodelijke elektroshocks te vermijden.

Trek de stekker uit het stopcontact (trek niet aan de kabel!) voordat u het

toestel reinigt en als u het niet gebruikt.

Page is loading ...

Velleman® Service and Quality Warranty

Velleman® has over 35 years of experience in the electronics

world and distributes its products in more than 85 countries.

All our products fulfil strict quality requirements and legal

stipulations in the EU. In order to ensure the quality, our products

regularly go through an extra quality check, both by an internal

quality department and by specialized external organisations. If, all

precautionary measures notwithstanding, problems should occur,

please make appeal to our warranty (see guarantee conditions).

General Warranty Conditions Concerning Consumer

Products (for EU):

• All consumer products are subject to a 24-month warranty on

production flaws and defective material as from the original date of

purchase.

• Velleman® can decide to replace an article with an equivalent

article, or to refund the retail value totally or partially when the

complaint is valid and a free repair or replacement of the article is

impossible, or if the expenses are out of proportion.

You will be delivered a replacing article or a refund at the value of

100% of the purchase price in case of a flaw occurred in the first

year after the date of purchase and delivery, or a replacing article

at 50% of the purchase price or a refund at the value of 50% of

the retail value in case of a flaw occurred in the second year after

the date of purchase and delivery.

• Not covered by warranty:

- all direct or indirect damage caused after delivery to the article

(e.g. by oxidation, shocks, falls, dust, dirt, humidity...), and by the

article, as well as its contents (e.g. data loss), compensation for

loss of profits;

- frequently replaced consumable goods, parts or accessories such

as batteries, lamps, rubber parts, drive belts... (unlimited list);

- flaws resulting from fire, water damage, lightning, accident,

natural disaster, etc. …;

- flaws caused deliberately, negligently or resulting from improper

handling, negligent maintenance, abusive use or use contrary to

the manufacturer’s instructions;

- damage caused by a commercial, professional or collective use of

the article (the warranty validity will be reduced to six (6) months

when the article is used professionally);

- damage resulting from an inappropriate packing and shipping of

the article;

- all damage caused by modification, repair or alteration performed

by a third party without written permission by Velleman®.

• Articles to be repaired must be delivered to your Velleman®

dealer, solidly packed (preferably in the original packaging), and

be completed with the original receipt of purchase and a clear flaw

description.

• Hint: In order to save on cost and time, please reread the

manual and check if the flaw is caused by obvious causes prior to

presenting the article for repair. Note that returning a non-

defective article can also involve handling costs.

• Repairs occurring after warranty expiration are subject to

shipping costs.

• The above conditions are without prejudice to all commercial

warranties.

The above enumeration is subject to modification according

to the article (see article’s manual).

Velleman® service- en kwaliteitsgarantie

Velleman® heeft ruim 35 jaar ervaring in de elektronicawereld en

verdeelt in meer dan 85 landen.

Al onze producten beantwoorden aan strikte kwaliteitseisen en aan

de wettelijke bepalingen geldig in de EU. Om de kwaliteit te

waarborgen,

ondergaan onze producten op regelmatige tijdstippen een extra

kwaliteitscontrole, zowel door onze eigen kwaliteitsafdeling als

door externe gespecialiseerde organisaties. Mocht er ondanks deze

voorzorgen toch een probleem optreden, dan kunt u steeds een

beroep doen op onze waarborg (zie waarborgvoorwaarden).

Algemene waarborgvoorwaarden consumentengoederen

(voor Europese Unie):

• Op alle consumentengoederen geldt een garantieperiode van 24

maanden op productie- en materiaalfouten en dit vanaf de

oorspronkelijke aankoopdatum.

• Indien de klacht gegrond is en een gratis reparatie of vervanging

van een artikel onmogelijk is of indien de kosten hiervoor buiten

verhouding zijn, kan Velleman® beslissen het desbetreffende

artikel te vervangen door een gelijkwaardig artikel of de

aankoopsom van het artikel gedeeltelijk of volledig terug te

betalen. In dat geval krijgt u een vervangend product of

terugbetaling ter waarde van 100% van de aankoopsom bij

ontdekking van een gebrek tot één jaar na aankoop en levering, of

een vervangend product tegen 50% van de kostprijs of

terugbetaling van 50 % bij ontdekking na één jaar tot 2 jaar.

• Valt niet onder waarborg:

- alle rechtstreekse of onrechtstreekse schade na de levering

veroorzaakt aan het toestel (bv. door oxidatie, schokken, val, stof,

vuil, vocht...), en door het toestel, alsook zijn inhoud (bv. verlies

van data), vergoeding voor eventuele winstderving.

- verbruiksgoederen, onderdelen of hulpstukken die regelmatig

dienen te worden vervangen, zoals bv. batterijen, lampen,

rubberen onderdelen, aandrijfriemen... (onbeperkte lijst).

- defecten ten gevolge van brand, waterschade, bliksem,

ongevallen, natuurrampen, enz.

- defecten veroorzaakt door opzet, nalatigheid of door een

onoordeelkundige behandeling, slecht onderhoud of abnormaal

gebruik of gebruik van het toestel strijdig met de voorschriften van

de fabrikant.

- schade ten gevolge van een commercieel, professioneel of

collectief gebruik van het apparaat (bij professioneel gebruik wordt

de garantieperiode herleid tot 6 maand).

- schade veroorzaakt door onvoldoende bescherming bij transport

van het apparaat.

- alle schade door wijzigingen, reparaties of modificaties

uitgevoerd door derden zonder toestemming van Velleman®.

• Toestellen dienen ter reparatie aangeboden te worden bij uw

Velleman®-verdeler. Het toestel dient vergezeld te zijn van het

oorspronkelijke aankoopbewijs. Zorg voor een degelijke verpakking

(bij voorkeur de originele verpakking) en voeg een duidelijke

foutomschrijving bij.

• Tip: alvorens het toestel voor reparatie aan te bieden, kijk nog

eens na of er geen voor de hand liggende reden is waarom het

toestel niet naar behoren werkt (zie handleiding). Op deze wijze

kunt u kosten en tijd besparen. Denk eraan dat er ook voor niet-

defecte toestellen een kost voor controle aangerekend kan worden.

• Bij reparaties buiten de waarborgperiode zullen transportkosten

aangerekend worden.

• Elke commerciële garantie laat deze rechten onverminderd.

Bovenstaande opsomming kan eventueel aangepast worden

naargelang de aard van het product (zie handleiding van het

betreffende product).

Garantie de service et de qualité Velleman®

Velleman® jouit d’une expérience de plus de 35 ans dans le

monde de l’électronique avec une distribution dans plus de 85

pays.

Tous nos produits répondent à des exigences de qualité

rigoureuses et à des dispositions légales en vigueur dans l’UE. Afin

de garantir la qualité, nous soumettons régulièrement nos produits

à des contrôles de qualité supplémentaires, tant par notre propre

service qualité que par un service qualité externe. Dans le cas

improbable d’un défaut malgré toutes les précautions, il est

possible d’invoquer notre garantie (voir les conditions de garantie).

Conditions générales concernant la garantie sur les produits

grand public (pour l’UE) :

• tout produit grand public est garanti 24 mois contre tout vice de

production ou de matériaux à dater du jour d’acquisition effective ;

• si la plainte est justifiée et que la réparation ou le remplacement

d’un article est jugé impossible, ou lorsque les coûts s’avèrent

disproportionnés, Velleman® s’autorise à remplacer ledit article

par un article équivalent ou à rembourser la totalité ou une partie

du prix d’achat. Le cas échéant, il vous sera consenti un article de

remplacement ou le remboursement complet du prix d’achat lors

d’un défaut dans un délai de 1 an après l’achat et la livraison, ou

un article de remplacement moyennant 50% du prix d’achat ou le

remboursement de 50% du prix d’achat lors d’un défaut après 1 à

2 ans.

• sont par conséquent exclus :

- tout dommage direct ou indirect survenu à l’article après livraison

(p.ex. dommage lié à l’oxydation, choc, chute, poussière, sable,

impureté…) et provoqué par l’appareil, ainsi que son contenu

(p.ex. perte de données) et une indemnisation éventuelle pour

perte de revenus ;

- tout bien de consommation ou accessoire, ou pièce qui nécessite

un remplacement régulier comme p.ex. piles, ampoules, pièces en

caoutchouc, courroies… (liste illimitée) ;

- tout dommage qui résulte d’un incendie, de la foudre, d’un

accident, d’une catastrophe naturelle, etc. ;

Page is loading ...

HQ Power PAR64 User manual

HQ Power PAR64 User manual

in other languages

Related papers

Other documents