Dometic miniCool EA 3120 User manual

Page is loading ...

2

GB

Please read these operating instructions carefully before putting the refrigeration unit

into operation. If you later sell or dispose of it, please ensure that the new owner

receives these operating instructions.

Please follow the installation details below carefully. Guarantee is valid for products

installed as described only. (See chapter 4. 1)

Thank you for choosing our appliance. We are sure it will provide you with trouble-free use.

In the following, we would like to familiarise you with some symbols, which we bring to your attention to ensure

the safe and efficient operation of the appliance:

source of danger, in event of improper operation

suggested useful tips to read

information concerning environmental protection

This refrigerator is intended for the storage of food and drinks.

Attention!

• This product is designed to be operated by adults. Children should not be allowed

to tamper with the controls or play with the product.

• Any electrical work required to install this appliance should be carried out by a

qualified electrician.

• This product should be serviced by an authorised Service Engineer, and only genuine

spare parts should be used.

• It is dangerous to alter the specifications or modify this product in any way.

• Care must be taken to ensure that the appliance does not stand on the electrical

supply cable.

• There are working parts in this product which heat up. Always ensure that there is

adequate ventilation as a failure to do this will result in component failure and

possible content loss. See installation instructions.

• Parts which heat up should not be exposed. Wherever possible the back of the

product should be close to a wall but leaving the required distance for ventilation as

stated in the installation instructions.

• Before defrosting, cleaning or maintenance work is carried out, be sure to switch off

the appliance and unplug it.

• DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Under no circumstances

should solid ice be forced off the cooling fins. Solid ice should be allowed to thaw

when defrosting the appliance. See defrost instructions.

• This appliance is heavy. Care should be taken when moving it.

• Under no circumstances should you attempt to repair the appliance yourself. Repairs

carried out by inexperienced persons may cause injury or more serious malfunctioning.

Refer to your local Service Centre and always insist on genuine spare parts.

• In this appliance the storage of any toxic or explosive substance is forbidden!

3

GB

CONTENTS

1. Unpacking

2. View of the appliance

3. Cleaning

4. Positioning the appliance

4. 1. Installation instruction

5. Using the appliance

5.1. Temperature regulation

6. Ice cubes

7. Useful suggestions

8. Defrosting, cleaning and maintenance

9. Changing the lightbulb

10. Reversing the door hang

11. Replacing the decorative door panel

12. Changing the feet

13. Assembly of door handle

14. Customer service

15. Putting into operation, technical data

15.1.Connecting to electrical mains

16. Environmental protection information

17. Recycling

Attention!

Since Ser. No. 637XXXXX or higher (see rating label) the refrigerators are equipped with evaporator sensor for

CUC.

IN CASE I

F YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, DOMETIC RT. DO NOT ACCEPT LIABILITY FOR

LOSS OR DAMAGE OF KEYS. HOWEVER A COMPLETE LOCK CAN BE SUPPLIED.

Attention!

Warranty arrangements are in accordance with EC Directive 44/1999/CE and the normal

conditions applicable in the country concerned.

For warranty or other servicing, such as spare-parts, please contact our Dometic

Service Network.

The warranty does not cover any damage due to improper use.

The warranty does not cover any modifications to the appliance or the use of non-

original Dometic spare-parts.

The warranty does not apply if the installing and operating instructions are not adhered to.

When contacting Dometic Service Network, please state the model, product number and

serial number. You will find this information on the data plate inside of the refrigerator.

4

GB

1. Door lock (if available)

2. Sensor

3. Thermostat knob

4. Evaporator

5. Lamp (if available)

Figure 1.

1. Unpacking

After removal from the cardboard packaging, make sure the appliance is not damaged. If you find damage

to the appliance resulting from transport, report it immediately to the transportation firm.

2. View of the appliance

IN IN CASE IF YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, DOMETIC ZRT DO NOT ACCEPT

LIABILITY FOR LOSS OR DAMAGE OF KEYS. HOWEVER WE WOULD BE HAPY TO SUPPLY A COMPLETE

LOCK AND KEY REPLACEMENT.

EA 3100 EA 3080 EA 3120

EA 3140

3. Cleaning

Clean the refrigerator thoroughly at intervals, as

necessary. Remove the shelves; these, the cabinet

interior and the door should be washed with a warm

solution of sodium bi-carbonate. Finally wipe over

with a cloth rinsed in warm water only, and dry with

a clean cloth. Do not wash any plastic parts in water

that is more than hand warm, and do not expose

them to dry heat. The outside of the cabinet should

be wiped down regularly with a clean, damp cloth.

NEVER USE STRONG CHEMICALS OR ABRASIVE

CLEANING MATERIALS ON ANY PART OF THE

CABINET.

4. Positioning the appliance

When first using this refrigerator please consider

the following points:

• ENSURE REFRIGERATOR IS LEVEL

• THE PIPEWORK AT THE BACK GETS HOT IN

USE

• THE REFRIGERATOR HAS NO ‘MOTOR’ AND

IS THEREFORE VIRTUALLY SILENT

• ALLOW AT LEAST 3 HRS. FOR SIGNS OF

COOLING

During the refrigeration process, the appliance gives

off heat from the condenser (under the upper part

of the rear cover) into the surrounding air. The more

ventilated the condenser is, the more effective the

refrigeration will be.

• The other condition for satisfactory operation is

that the appliance is levelled. This could be

checked by placing

a glass of water on top of the

appliance.

• It is important that the appliance is not directly

exposed to radiated heat (sunlight, radiator, near

an oven, etc.).

4.1. Installation instructions

The refrigerator is equipped with an electrically

heated absorption cooling unit which is virtually silent

in operation. The fridge is designed for free-standing

installation, but can be built-in if the following

conditions are complied with to ensure satisfactory

operation and maximum cooling efficiency.

IMPORTANT

Please follow the installation details below

carefully. Guarantee is valid for products

installed as described only.

1. The refrigerator must be

level both directions

2. There should be

20mm clearance to the wall

3. Ventilation must be provided

as shown in

alternatives A, B, C or D (fig 2-3)

4. The ventilation duct must at least measure

105mm x the width of the refrigerator

5.

Only the entire cooling unit must project into

the duct as shown

6.

Air passing through the duct must not be

5

GB

7. Ventilation grills, if used, must have an free

openings of

at least 200cm2 each

During installation, please ensure the mains

plug is accessible at all times.

5. Using the appliance

• To start the refrigerator connect the plug into a

properly earthed socket.

• The cooling fins should show signs of cooling

after about 3 hours. The refrigerator needs about

6 hours at normal ambient temperature to reach 6

°C in the storage compartment.

5.1. Temperature regulation

The usual setting required is in the region of 2 to 3 on

the thermostat knob (Fig. 4), but this can vary with

Figure 2.

Figure 3.

6

GB

Figure 5.

conditions of load and installation. If it is found

necessary to change the setting, the knob can be

turned to a higher number to give a lower temperature,

or a lower number to give a higher temperature. The

effect of any adjustment can be checked by means

of a thermometer when the refrigerator has reached

the new temperature after some hours.

“0”, disconnect the refrigerator from the electricity

supply and leave the cabinet door open. After

defrosting the cabinet interior should be wiped out

with a clean, damp cloth.

Figure 4.

6. Ice cubes

Fill the ice tray up to 4/5 with drinking water, and

place the ice tray on the ice-tray shelf. Wipe off

any excess water to prevent the ice tray from

freezing to the surface.

To speed up the making of ice cubes, turn the

thermostat to position 5 for a short while. Remember

to turn the dial to its normal setting when the ice

cubes are frozen.

To remove the cubes from the ice tray, hold it under

running water. The ice cubes can now be taken out

easily

7. Useful suggestion

Do not overfill the appliance. Put warm foods and

drinks in the appliance only when they have cooled

down to room temperature. It is advisable to leave

some space between the products in the cabinet to

ensure efficient and even cooling. If the shelves

are packed too tightly there may be unacceptable

temperature variations.

8. Defrosting, cleaning and

maintenance

This frost-formation is kept back by the FUZZY

LOGIC system built into the appliance.

The first defrosting phase commences 39 hours

after the start and lasts for two hours.

After this, the device operates for 22 hours at a

time, followed by a defrosting period of 2 hours.

The frost will melt and the defrost water will run

through the drain tube from the drip channel into an

evaporating vessel located at the bottom rear of the

refrigerator. (Fig 5) The defrost water will evaporate

automatically into the circulating air and the vessel

will not need emptying.

To switch off the unit, turn the thermostat knob to

9. Changing the lightbulb (If available)

If the lightbulb needs changing, pull out the plug and

proceed as follows:

Press the metal reflector to one side and draw the

lamp covering backwards. Replace the bulb and

push the covering back into place.

A new 10-watt bulb can be obtained at any service

shop.

10. Reversing the door hang

(Fig. 6)

Lay the appliance on its back. Remove the 8 screws

(1). Remove the door, together with the two hinges

(2), from the housing.

Remove the two cover caps (3) from the housing

and place them in the open hinge holes in the housing.

Place the bottom righthand hinge in the top left of

the door and the top righthand hinge in the bottom

left of the door and hang the door on its hinges in the

open cover cap holes in the housing. Secure the

hinges and cover caps with the 8 screws.

Check that the door closes easily and is sealed

properly.

Figure 6

11. Replacing the decorative door

panel (Fig. 7-9)

Remove the two screws (1) from the upper hinge of

the door.

Pull the door together with the hinge away from the

housing and up off the lower hinge bolt (2-3).

Remove screws (4) and pull off the frame edge (5).

Slide the decorative panel (6) out of the door frame

and insert the new panel (7), so that the upper edge

of the panel runs exactly parallel to the upper edge

of the frame. A new panel can be inserted more

easily into the upper edge of the frame when the two

corners are cut off by approx. 5 x 5mm (8). Put the

frame edge (5) back in place and secure with screws.

Place the door on the lower hinge (9), slot the upper

hinge into the opening, press together with the door

against the housing and secure with the two screws

(11).

7

GB

14. Customer service

Before you call a service engineer, carry out the

following simple tests:

• Is there a power failure? Check the fuses.

• Is the plug firmly connected to the socket and is

the socket switched on? Check the socket by

plugging in another appliance, e. g. a table lamp.

• Is the thermostat at the correct setting? (nor-

mally 2 or 3).

• Has the door not been closed properly causing

the inside temperature to rise too quickly?

• Is the refrigerator level?

• Has the ventilation become obstructed?

Figure 7

Figure 8

Figure 9

12. Changing the feet

(Fig. 10)

Should you wish to install your miniCool, you will not

need the 40-mm feet. After having removed the 40-

mm feet, you can then re-attach the 12-mm feet,

located inside the 40-mm feet, to the front and rear

fixing points. The 40-mm feet and the 4 remaining

screws should be retained for future use.

Figure 10

13. Assembly of door handle

(Fig. 11)

Figure 11

If after checking all the above points, the refrigera-

tor is still not working satisfactorily, contact your

nearest service engineer. State the problem, model,

product- and serial-number.

(Details of the model, product- and serialnumber are

to be found on the data label in the top left of the

inside compartment.)

This refrigerator is equipped with overheating pro-

tection. An authorised service technician can check

whether this has been triggered or not.

In the event of a fault developing, contact your

nearest Service Centre-see local telephone direc-

tory.

8

GB

15.1. Connecting to electrical

mains

The appliance may only be operated from

nominal voltage mains as shown on the data

plate. The appliance mains plug may be connected

to a mains socket earthed in accordance with

regulations.

Any electrical work required to install this appliance

should be carried out by a qualified electrician or

competent person.

The manufacturer declines any liability should

these safety measures not be observed.

Electrical Requirements

Before switching on, make sure the electricity supply

voltage is the same as that indicated on the appliance

rating plate.

Only for UK:

The appliance is supplied with a 3 amp plug fitted. In

the event of having to change the fuse in the plug

supplied, a 3 amp ASTA approved (BS 1362) fuse

must be used. Should the plug need to be replaced

for any reason, the wires in the mains lead are

coloured in accordance with the following code:

Green and Yellow:Earth

Blue: Neutral

Brown: Live

The wire coloured green and yellow must be

connected to the terminal marked with the letter „E“

or by the earth symbol ” „ or coloured green and

yellow.

The wire coloured blue must be connected to the

terminal „N“ or coloured black.

The wire coloured brown must be connected to the

terminal marked „L“ or coloured red.

Upon completion there must be no cut, or stray

strands of wire present and the cord clamp must be

secure over the outer sheath

16.Environmental protection

information

The appliance does not contain any CFCs/HCFCs.

Ammonia (natural hydrogen and nitrogen compound)

is used as a refrigerating agent in the refrigeration

unit.

The ozone-friendly cyclopentane is activated as a

motive agent for the PU foam insulation.

Sodium chromate is used for corrosion protection

(less than 2 weight % of the coolant).

17. Recycling

After unpacking the appliance, the packing materials

should be delivered to a local collection site. At the

end of its useful lifetime, the appliance should be

delivered to a specialized collection and reprocessing

firm, which reclaims the usable materials. The rest

is properly destroyed.

15. Putting into operation

Technical data:

Model EA 3100 EA 3080 EA 3120 EA 3140

EA 0300, EA 0301 RA 80 RA 140

EA 0302 RA0450

Type MF20-60 MF20-60 MF20-60 MF20-60

Gross volume 31 litre 23 litre 31 litre 41 litre

Mains operation 220 - 240V (AC) 220 - 240V (AC) 220 - 240V (AC) 220 - 240V (AC)

Input 90W 90W 90W 90W

Energy consumption 0,97 kWh/24h 0,92 kWh/24h 0,99 kWh/24h 1,07 kWh/24h

Climate class N N N N

Refrigerant 159g H

2

O + 86g NH

3

159g H

2

O + 86g NH

3

159g H

2

O + 86g NH

3

159g H

2

O + 86g NH

3

Appliances bearing this symbol must be

deposited at the designated local reception

point for the disposal of electrical and

electronic equipment.It is not permitted that

this product be disposed of by way of the normal

household refuse collection system.

Dometic refrigerators bear this symbol on the

specifications plate (data plate) to be found in the

interior of the unit.

9

GB

This appliance complies with the

following EEC directives:

LVD-Directive 73/23/EEC

with amendment

90/683/EEC

EMC-Directive 89/336/EEC

RoHS-directive 2002/95/EC

Page is loading ...

EA 3100 EA 3080 EA 3120

EA 3140

28

1. Disimballaggio

Rimuovere l’imballaggio in cartone e accertarsi che l’apparecchio non sia danneggiato. In caso di danni

all’apparecchio dovuti al trasporto, contattare immediatamente la società di trasporti.

2. Schema dell’apparecchio

Figura 1.

1. Serratura porta (Se in dotazione) 3. Pomello termostato 5. Lampada (Se in dotazione)

2. Sensore 4. Evaporatore

SE IL FRIGORIFERO FOSSE DOTATO DI SERRATURA, DOMETIC ZRT NON È RESPONSABILE

DELL’EVENTUALE PERDITA O DANNEGGIAMENTO DELLE RELATIVE CHIAVI. IN TAL CASO POTRÀ

ESSERE FORNITA UNA SERRATURA DI RICAMBIO COMPLETA.

IT

Page is loading ...

EA 3100 EA 3080 EA 3120

EA 3140

52

1. Desembalagem

Após ter retirado o aparelho da sua embalagem de cartão, certifique-se de que o mesmo não esteja

danificado. Se constatar qualquer dano causado pelo transporte, contacte imediatamente a empresa

responsável pelo transporte, avisando-a da ocorrência.

2. Vista do aparelho

PT

Figura 1

1. Fecho da porta (se existir) 3. Botão do termostato 5. Lãmpada (se existir)

2. Sensor 4. Evaporador 6. Dobradiça.

A DOMETIC ZRT APARELHOS PARA OS TEMPOS LIVRES NÃO ACEITA QUALQUER RESPONSABILIDADE

PELA PERDA OU DANIFICAÇÃO DE CHAVES. TODAVIA, TEREMOS TODO O PRAZER EM FORNECER UM

CONJUNTO COMPLETO DE FECHOS E CHAVES DE SUBSTITUIÇÃO.

Page is loading ...

EA 3100 EA 3080 EA 3120

EA 3140

81

1. Pakkauksen purkaminen

Kun purat kuljetuspakkauksen tarkista, ettei laite ole vahingoittunut kuljetuksessa. Kuljetusvaurioista on

välittömästi ilmoitettava kuljetusliikkeelle.

2. Kuva jääkaapista

SF

Kuva 1

1. ovilukko (ei kaikissa malleissa) 3. termostaatin säätönuppi 5. lamppu (ei kaikissa malleissa)

2. termostaatin anturi 4. höyrystin

JOS JÄÄKAAPISSA ON LUKKO, DOMETIC-YHTIÖ EI OLE VASTUUSSA AVAIMIEN HÄVIÄMISESTÄ TAI

VAHINGOITTUMISESTA. TARVITTAESSA TOIMITAMME LAITTEESEEN UUDEN LUKON JA AVAIMET.

Page is loading ...

Dometic miniCool EA 3120 User manual

Dometic miniCool EA 3120 User manual

in other languages

Related papers

Other documents