OPERATOR'S
MANUAL
c^HUSKY
6 FT WORKBENCH
MODEL # 72WB01SS-THD
AT
LEAST
TWO
PERSONS.
SERVICE
PARTS
CALL
1-866-440-3170
FOR
SERVICE
PARTS.
Please
provide the Model Number when calling. To expand your garage
storage project, please visitwww.homedepot.com/garagestorage
for additional product options.
Locating
Model
#
Information
Model numbers and other information required for service parts is
located on a white label on the upper right hand corner of the unit.
CAPACITIES
• Weight of the unit is 94 lbs.
• The maximum load capacity for the work surface is 1000 lbs.
evenly distributed.
• The maximum product weight, including contents stored on the
work surface is 1094 lbs.
MAINTENANCE
PAINTED
SURFACES:
• Periodically the surfaces should be cleaned with a mild
detergent and water.
• Grease and oil can be removed with most standard cleaning
fluids.
For safety, use a nonflammable cleaning
fluid.
• Auto wax will preserve the unit's luster
finish.
Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
STAINLESS
SURFACES:
• Stainless steel can discolor when exposed to pool chemi-
cals,
saltwater or cleaners with bleach.
• Keep your stainless looking new by cleaning with a good
quality all-in-one stainless steel cleaner polish monthly.
Frequent cleaning will remove surface contamination that
could lead to rust.
• Do not
clean
with
steel
wool or other
abrasive
pads.
• Do not use
cleaners
not
specifically
Intended
for
stainless
steel
on
stainless
surfaces
(this
Includes
glass,
tile
and counter
cleaners).
SAFETY
DANGER
A is used to indicate a hazardous
situation which, if not avoided, wjl! result in serious injury
or
death.
—'
WARNING
A indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION
is used to indicate a hazardous situation
which,
if not avoided, may result in minor injury, moderate
injury, or property damage.
CAUTION:
Read and follow all Safety Rules and
Operating Instructions before first use of this product.
DANGER
A
• DO NOT stand on this product. You may fall which may
cause personal injury.
• DO NOT mount this product on a truck bed or any
other moving object. This may cause personal injury or
product Damage.
.
APPROPRIATELY
SECURE this product before
moving it with a forklift.
WARNING
A
. USE
APPROPRIATE
SAFETY equipment when
using power and hand tools. Failure to do so may cause
personal injury or product damage.
• USE
ADEQUATE
MANPOWER
when assembling
and moving this unit. Failure to do so may cause personal
injury or product damage.
• DO NOT alter this product in any manner. This may
cause product damage or personal injury.
•
UNIT
MUST
BE located on a level surface. The
product may become unstable and tip if stored or moved
on an un-level surface, which may cause personal injury
or product damage.
F1831
HARDWARE
CARTON
CONTENTS
TOOLS
REQUIRED:
^1°©
Socket Wrench
3/8in
Socket Extension B. Rail - Top Back
7/16in
Deep-well Socket
3/8in
Wrench C. Workbench Top
Drill 1/8in Drill bit D. Rail - Top Front
Square Tape measure E- Bottom Rail
OPTIONAL
TOOLS:
Screwdriver, Flathead and
7/16-in
Open
End
Wrench
ASSEMBLY
SIDE
CONSTRUCTION
Items Needed:
A-Side (Qty: 2)
AA -
1/4-20
X
5/8in
Carriage Bolt (Qty: 4)
BB-5/16in Washer (Qty: 4)
CC -1/4-20 Flange Nut (Qty: 4)
EE - Screw Leveler (Qty: 4)
FF - Leveling Foot, Left (Qty: 2)
GG - Leveling Foot, Right (Qty: 2)
Process:
• Place (1) leveling foot pad FF and (1) leveling foot pad
GG on each side at the bottom. Make sure each leveling
foot is fully seated on each corner.
• Secure each Leveling Foot with (1) boltAA, (1) Washer
BBand(1)NutCC.
• Wrench tighten.
•Assemble (1) leveler EE in each leveling foot Some
adjustments may be necessary after workbench is in
desired position.
Figure 1
TOP
RAIL
ASSEMBLY
Items Needed:
B-Rail-Top
Back (Qty: 1)
D-Rail-Top
Front (Qty: 1)
AA -1/4-20
X
5/8in
Carriage Bolt (Qty: 8)
BB-5/16 Washer (Qty: 8)
CC -
1/4-20
Serrated Flange Nut (Qty: 8)
Process:
• Place Workbench
Top,
with stainless steel side facing
down.
(Use packaging material to prevent scratches.)
NOTE:
The Rail with the Husky® nameplate should be
placed toward the front of the unit
with
the nameplate
position upside down.
•Assemble (2) sides A and rails B and D, as shown using
(8)
bolts
AA,
(8) washer BB, and (8) nut CC. Holes on
rails should be facing to the outside of the workbench top.
•
Finger
tighten.
Front
Holes
facing out
Back
Figure 2
3
BOTTOM RAIL ASSEMBLY
Items Needed:
E-Bottom
Rail (Qty: 1)
AA -1/4-20
X
5/8in
Carriage Bolt (Qty: 4)
BB-5/16in Washer (Qty: 4)
CC -1/4-20 Flange Nut (Qty: 4)
Process:
• Attach rail E in top back set of holes in both sides A as
shown,
using (4) bolts
AA,
(4) washers BB, and (4) nuts
CC.
Flanges of Rail E should point in.
• Finger tighten.
Flanges
point
In
Front
Back
Bottom
Rail
Figure 3
IMPORTANT:
• YOU MUST
SQUARE
THE
UNIT
AND
WRENCH
TIGHTEN ALL
FASTENERS
TO
ENSURE
STABILITY.
TOP
ATTACHMENT
items Needed:
C - Workbench Top
DD - #14-10
X
5/8in
Hex Screw (Qty: 6)
Drill
1/8in Drill Bit
Process:
• Position frame assembly on Workbench Top,
as desired.
NOTE:
The back of
the
work bench frame must be at
least 1-1/2 inches (38 mm) from the back of the
Workbench Top.
• Mark centers of (6) mounting holes.
• Remove workbench frame in order to drill pilot holes.
• Drill (6) 1/8in pilot holes 1/2in deep in mounting
hole locations.
• Reposition workbench assembly on Workbench Top.
• Attach using (6) Hex Screws DD.
NOTE:
Additional fasteners may be used to attach
workbench top through holes in side support if desired.
(Not supplied)
1-1/2
Inches
38 mm
Figure 4
Mounting
Holes
>
Using help (second person) lift workbench up and
rotate onto leveling feet FF and GG. Do not rest on
side of legs while rotating workbench to its upright
position.
Damage could occur.
>
Place the workbench in its upright position.
• Move workbench to desired location and adjust level-
ing feet FF and GG to make workbench level and
secure. (See operation.)
REMOVING
PROTECTIVE
FILM FROM
STAINLESS
STEEL
• Starting at one of the corners, peel back the protective
coating from the stainless top.
• Be sure to remove all the protective coating before
initial use.
• Follow the cleaning methods in thev maintenance sec-
tion to keep the stainless looking new.
OPERATION
Leveling Foot Adjustment
•Adjust leveling foot to desired position with flathead
screwdriver or 7/1 Bin open end wrench as shown.
4
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Craftsman 5-Drawer User manual
-
Craftsman 706.146440 User manual
-
-
-
-
-
-
Unbranded IMP 657-1000 Operating instructions
-
-
Excalibur 40-100C User guide