Page is loading ...
OPERATOR’S MANUAL
6 FT WORKBENCH
MODEL # 72WB01SS-THD
• Weight of the unit is 94 lbs.
• The maximum load capacity for the work surface is 1000 lbs.
evenly distributed.
• The maximum product weight, including contents stored on the
work surface is 1094 lbs.
Locating Model # Information
Model numbers and other information required for service parts is
located on a white label on the upper right hand corner of the unit.
• Periodically the surfaces should be cleaned with a mild
detergent and water.
• Grease and oil can be removed with most standard cleaning
uids. For safety, use a nonammable cleaning uid.
• Auto wax will preserve the unit’s luster nish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
DANGER is used to indicate a hazardous
situation which, if not avoided, will result in serious injury
or death.
WARNING indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation
which, if not avoided, may result in minor injury, moderate
injury, or property damage.
CAUTION: Read and follow all Safety Rules and
Operating Instructions before rst use of this product.
DANGER
• DO NOT stand on this product. You may fall which may
cause personal injury.
• DO NOT mount this product on a truck bed or any
other moving object. This may cause personal injury or
product Damage.
• APPROPRIATELY SECURE this product before
moving it with a forklift.
WARNING
• USE APPROPRIATE SAFETY equipment when
using power and hand tools. Failure to do so may cause
personal injury or product damage.
• USE ADEQUATE MANPOWER when assembling
and moving this unit. Failure to do so may cause personal
injury or product damage.
• DO NOT alter this product in any manner. This may
cause product damage or personal injury.
• UNIT MUST BE located on a level surface. The
product may become unstable and tip if stored or moved
on an un-level surface, which may cause personal injury
or product damage.
• Stainless steel can discolor when exposed to pool chemi-
cals, saltwater or cleaners with bleach.
• Keep your stainless looking new by cleaning with a good
quality all-in-one stainless steel cleaner polish monthly.
Frequent cleaning will remove surface contamination that
could lead to rust.
• Do not clean with steel wool or other abrasive pads.
• Do not use cleaners not specically intended for
stainless steel on stainless surfaces (this includes
glass, tile and counter cleaners).
PAINTED SURFACES:
STAINLESS SURFACES:
CALL 1-866-440-3170 FOR SERVICE PARTS. Please
provide the Model Number when calling. To expand your garage
storage project, please visit www.homedepot.com/garagestorage
for additional product options.
F1831
SERVICE PARTS
SAFETY
CAPACITIES
MAINTENANCE
NOTE: IT IS RECOMMENDED
THAT UNIT IS ASSEMBLED WITH
AT LEAST TWO PERSONS.
TOOLS REQUIRED:
Socket Wrench 3/8in Socket Extension
7/16in Deep-well Socket 3/8in Wrench
Drill 1/8in Drill bit
Square Tape measure
OPTIONAL TOOLS: Screwdriver, Flathead and 7/16-in
Open End Wrench
HARDWARE INCLUDED:
A. Side
B. Rail - Top Back
C. Workbench Top
D. Rail - Top Front
E. Bottom Rail
DD - #14-10 x 5/8in Hex
Screw (Qty: 6)
AA - 1/4-20 x 5/8in Carriage
Bolt (Qty: 16)
BB - 5/16in Washer (Qty: 16)
CC - 1/4-20 Serrated Flange
Nut (Qty: 16)
EE - Screw Leveler (Qty: 4)
FF - Leveling Foot,
Left (Qty: 2)
GG - Leveling Foot,
Right (Qty: 2)
2
HARDWARE CARTON CONTENTS
C
A(2)
B
E
D
Process:
• Place (1) leveling foot pad FF and (1) leveling foot pad
GG on each side at the bottom. Make sure each leveling
foot is fully seated on each corner.
• Secure each Leveling Foot with (1) bolt AA, (1) Washer
BB and (1) Nut CC.
• Wrench tighten.
• Assemble (1) leveler EE in each leveling foot. Some
adjustments may be necessary after workbench is in
desired position.
SIDE CONSTRUCTION
Items Needed:
A - Side (Qty: 2)
AA - 1/4-20 x 5/8in Carriage Bolt (Qty: 4)
BB - 5/16in Washer (Qty: 4)
CC - 1/4-20 Flange Nut (Qty: 4)
EE - Screw Leveler (Qty: 4)
FF - Leveling Foot, Left (Qty: 2)
GG - Leveling Foot, Right (Qty: 2)
Items Needed:
B - Rail - Top Back (Qty: 1)
D - Rail - Top Front (Qty: 1)
AA - 1/4-20 x 5/8in Carriage Bolt (Qty: 8)
BB - 5/16 Washer (Qty: 8)
CC - 1/4-20 Serrated Flange Nut (Qty: 8)
3
ASSEMBLY
Figure 1
Figure 2
Process:
• Place Workbench Top, with stainless steel side facing
down. (Use packaging material to prevent scratches.)
NOTE: The Rail with the Husky® nameplate should be
placed toward the front of the unit with the nameplate
position upside down.
• Assemble (2) sides A and rails B and D, as shown using
(8) bolts AA, (8) washer BB, and (8) nut CC. Holes on
rails should be facing to the outside of the workbench top.
• Finger tighten.
TOP RAIL ASSEMBLY
Holes
facing out
Back
Front
Leveler
(on top)
D
A
B
CC
BB
AA
• Using help (second person) lift workbench up and
rotate onto leveling feet FF and GG. Do not rest on
side of legs while rotating workbench to its upright
position. Damage could occur.
• Place the workbench in its upright position.
• Move workbench to desired location and adjust level-
ing feet FF and GG to make workbench level and
secure. (See operation.)
Leveling Foot Adjustment
• Adjust leveling foot to desired position with athead
screwdriver or 7/16in open end wrench as shown.
Process:
• Position frame assembly on Workbench Top,
as desired.
NOTE: The back of the work bench frame must be at
least 1-1/2 inches (38 mm) from the back of the
Workbench Top.
• Mark centers of (6) mounting holes.
• Remove workbench frame in order to drill pilot holes.
• Drill (6) 1/8in pilot holes 1/2in deep in mounting
hole locations.
• Reposition workbench assembly on Workbench Top.
• Attach using (6) Hex Screws DD.
NOTE: Additional fasteners may be used to attach
workbench top through holes in side support if desired.
(Not supplied)
Process:
• Attach rail E in top back set of holes in both sides A as
shown, using (4) bolts AA, (4) washers BB, and (4) nuts
CC. Flanges of Rail E should point in.
• Finger tighten.
IMPORTANT:
• YOU MUST SQUARE THE UNIT AND
WRENCH TIGHTEN ALL FASTENERS TO
ENSURE STABILITY.
BOTTOM RAIL ASSEMBLY
Items Needed:
E - Bottom Rail (Qty: 1)
AA - 1/4-20 x 5/8in Carriage Bolt (Qty: 4)
BB - 5/16in Washer (Qty: 4)
CC - 1/4-20 Flange Nut (Qty: 4)
Figure 3
Flanges
point in
Back
Front
Bottom Rail
BB
AA
CC
4
OPERATION
REMOVING PROTECTIVE FILM FROM
STAINLESS STEEL
• Starting at one of the corners, peel back the protective
coating from the stainless top.
• Be sure to remove all the protective coating before
initial use.
• Follow the cleaning methods in thev maintenance sec-
tion to keep the stainless looking new.
TOP ATTACHMENT
Items Needed:
C - Workbench Top
DD - #14-10 x 5/8in Hex Screw (Qty: 6)
Drill
1/8in Drill Bit
Mounting Holes
Figure 4
1-1/2 inches
38 mm
/